Clarke CAV12 is especially designed for fine dust pick-up produced while grinding wood or gypsum, which makes it ideal for construction sites or workshops. It has a powerful motor that provides 127 CFM airflow for efficiently cleaning up even the finest dust particles, leaving the surfaces spotless. The 12-gallon tank offers ample capacity for extended cleaning sessions without the need for frequent emptying.
The triple-layer filtration system ensures maximum dust capture and prevents fine particles from escaping back into the air, contributing to a cleaner and healthier work environment. The tank liner's synthetic linen material allows for effortless dust removal, while the filter liner traps finer particles and the primary filtering element handles the ultra-fine ones. Cleaning and maintaining the filters is simple, ensuring optimal performance over time.
Clarke CAV12 is especially designed for fine dust pick-up produced while grinding wood or gypsum, which makes it ideal for construction sites or workshops. It has a powerful motor that provides 127 CFM airflow for efficiently cleaning up even the finest dust particles, leaving the surfaces spotless. The 12-gallon tank offers ample capacity for extended cleaning sessions without the need for frequent emptying.
The triple-layer filtration system ensures maximum dust capture and prevents fine particles from escaping back into the air, contributing to a cleaner and healthier work environment. The tank liner's synthetic linen material allows for effortless dust removal, while the filter liner traps finer particles and the primary filtering element handles the ultra-fine ones. Cleaning and maintaining the filters is simple, ensuring optimal performance over time.
Form No. 71073A 4/06
Vacuum 12 Gallon
Operator's Manual
Manual del operador
Manuel de l’utilisateur
This book has important information for the use and safe operation of this machine. Failure to read
this book prior to operating or attempting any service or maintenance procedure to your Clarke
American Sanders machine could result in injury to you or to other personnel; damage to the machine
or to other property could occur as well. You must have training in the operation of this machine
before using it. If your operator(s) cannot read this manual, have it explained fully before attempting
to operate this machine.
All directions given in this book are as seen from the operator’s position at the rear of the machine.
For new books write to: Clarke
®
, 2100 Highway 265, Springdale, Arkansas 72764
English (2 - 6)
Español (8 - 12)
Français (14 - 18)
READ THIS BOOK
LEA ESTE MANUAL
LISEZ CE MANUEL
ES
EN
FR
EN
ENGLISH
-2- Clarke
®
American Sanders Operator's Manual (EN) - CAV 12
Table of Contents
Important Safety Instructions ....................................................................................3
Specifications .........................................................................................................4
Introduction and Instructions.....................................................................................4
Grounding Instructions .............................................................................................5
Maintenance and Repair .........................................................................................6
Troubleshooting.......................................................................................................6
Section II Parts and Service Manual
Assembly Drawing #1 .............................................................................................20
Assembly Drawing #2 .............................................................................................21
Assembly Drawing #3 .............................................................................................22
EN
ENGLISH
Clarke
®
American Sanders Operator's Manual (EN) - CAV 12 - 3 -
DANGER: Failure to read and observe all DANGER statements could result in severe
bodily injury or death. Read and observe all DANGER statements found in
your Operator's Manual and on your machine.
WARNING: Failure to read and observe all WARNING statements could result in injury
to you or to other personnel; property damage could occur as well. Read
and observe all WARNING statements found in your Operator's Manual and
on your machine.
CAUTION: Failure to read and observe all CAUTION statements could result in damage
to the machine or to other property. Read and observe all CAUTION
statements found in your Operator's Manual and on your machine.
READ ALL INSTRUCTIONS BEFORE USE
WARNING:
To reduce the risk of fire, electric shock, or injury:
- Use only as described in this manual. Use only manufacturers recommended attachments.
- For indoor dry pick-up only. Do not expose to rain or weather.
- If machine is not working as it should, has been dropped, damaged, left outdoors, or dropped in water,
return it to a service center.
- Turn off all controls before unplugging
- Do not handle plug or machine with wet hands.
- Do not use with damaged plug or cord.
- Do not unplug by pulling on cord. To unplug, grasp the plug not the cord.
- Do not pull or carry by cord, use cord as a handle, close a door on the cord, or pull cord around sharp
edges or corners. Do not run machine over cord. Keep cord away from heated surfaces.
- Do not leave machine when plugged in. Unplug from outlet when not in use or before servicing.
- Do not put any objects into openings. Do not use with any openings blocked. Keep free of dust, lint,
hair, and anything that may reduce airflow.
- Keep hair, loose clothing, fingers, and body parts away from openings and moving parts.
- Do not use to pick-up flammable or combustible liquids, such as gasoline or solvents. Do not use
where they may be present.
- Do not use to pick-up hot, smoldering, or burning substances.
- Do not use where explosive vapors, such as gas, solvents, alcohol, fuels, or combustible materials such
as grain, wood dust, are present in the air. Keep the work area well ventilated.
- Dust produced from sanding wood or varnish could self ignite causing injury or damage. If this material
has been picked up, empty it immediately after use in a metal container.
- Do not use to pick-up health endangering dust.
- Do not use unless machine is fully assembled. Do not modify the machine. Read all instructional
labels on the machine. Replace damaged labels.
- Do not allow to be used as a toy. Close attention is necessary when used around children.
- Use extra care when cleaning on stairs.
- Connect to properly grounded outlet. See “grounding Instructions”.
- Do not use unless all filtering elements are present. Clean filtering elements frequently.
SAVE THESE INSTRUCTIONS.
IMPORTANT SAFETY INSTRUCTIONS
EN
ENGLISH
-4- Clarke
®
American Sanders Operator's Manual (EN) - CAV 12
Model CAV 12
Voltage 120 V
Frequency 60 Hz
Power 1000 W
Volume Flow (CFM) 127
Static Lift (inches H
2O) 92
Sound Level dB(A) 57
Cord Length (ft.) 25
Tank Volume 12 gal.
Width (in.) 18 3/4
Depth (in.) 19 29/32
Height (in.) 25 25/32
Weight (lbs.) 31
SPECIFICATIONS
INTRODUCTION AND INSTRUCTIONS
The CAV 12 comes fully assembled. It is specifically designed
for dry pick-up of fine dust made from the grindings of wood or
gypsum.
Intalled are three filtering elements (see figure 1). The
elements include the Tank Liner (part number 53856A), the
Filter Liner (part number 61156112), and the Primary Filter
Element (part number 63990). Each of these elements plays
a significant role in the machines overall performance.
NOTE: When performance has declined noticeably, empty
tank and clean the filters accordingly.
The Tank Liner (figure 1, A)
The tank liner filters all the larger particles and a proportion of
the fine. It is made from synthetic linen that easily releases
trapped dust for effortless cleaning. After use, but before
removing from tank, tap or shake the liner surface to release
the dust.
It is installed over the top rim of the tank. Center the tank liner
with respect to the rim before installing the head.
The Filter Liner (figure 1, B)
The filter liner traps the fine particles that pass through the
tank filter. It should be removed and cleaned weekly under
normal use. It is secured over the primary filtering element
with an elestic band. When reinstalling, the elastic band
should pinch upon the base of the primary filtering element
and not the paper.
The Primary Filtering Element (figure 1, C)
The primary filtering element traps the fine and ultra fine
particles that have escaped the filter liner. Clean with a gentle
stream of compressed air annually. Direct the stream onto the
inner surfaces of the filter. Replace if it has become damaged,
wet, or if performance is not restored after cleaning.
Figure 2
A
B
C
EN
ENGLISH
Clarke
®
American Sanders Operator's Manual (EN) - CAV 12 - 5 -
Figure 2
Figure 3
Figure 4
INTRODUCTION AND INSTRUCTIONS, cont.
WARNING: Wood and varnish sanding dust could self
ignite and cause injury or damage. If these substances
have been picked up with this machine, empty immediately
after use, into a metal container.
Operation Switch
The operation switch is located on the control panel (see figure
2). To activate, turn the switch clockwise. See that the switch
is turned off before connecting or disconnecting the plug.
Removing or Securing the Head
The head is held to the tank by two clamps. Lift the clamps to
release it from the tank (see figure 3). Press in on the clamps
to secure it to the tank.
GROUNDING INSTRUCTIONS
This appliance must be grounded. If it should malfunction or
breakdown, grounding provides a path of least resistance for
electric current to reduce the risk of electric shock. This appli-
ance is equipped with a cord having an equipment-grounding
conductor and grounding plug. The plug must be plugged into
an appropriate outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
WARNING: Improper connection of the equipment-
grounding conductor can result in a risk of electric
shock. Check with a qualified electrician or service
person if you are in doubt as to whether the outlet is
properly grounded. Do not modify the plug provided with
the product - if it will not fit the outlet, have a proper outlet
installed by a qualified
electrician.
This appliance is for use on a nominal 120-volt circuit and has a
ground plug that looks like the plug illustrated in figure 4. Make
sure that the appliance is connected to an outlet having the
same configuration as the plug. No adapter should be used
with this appliance.
WARNING: To prevent possible electric shock, protect the
machine from rain. Keep the machine in a dry building.
WARNING: To prevent possible electric shock, always use
a 3-wire electrical system connected to the electrical ground.
For maximum protection against electrical shock, use a
circuit that is protected by a ground fault circuit interrupter.
Consult your electrical contractor.
WARNING: Do not cut, remove or break the ground pin. If the
outlet does not fit the plug, consult your electrical contractor.
WARNING: Have worn, cut or damaged
cords replaced by an authorized service person.
EXTENSION CORDS
Use only an approved extension cord with three conductors, a
plug with three terminals, and a connector body with three
holes. The machine has a power cord with wire size 16 AWG
(AWG means American Wire Gauge).
WARNING: If you use an extension cord, use an extension
cord with minimum wire size 14 AWG. Do not use an
extension cord longer than 50 feet. Do not join two
extension cords.
Grounding
Pin
Grounded
Outlet
Grounded
Outlet
Box
(A)
EN
ENGLISH
-6- Clarke
®
American Sanders Operator's Manual (EN) - CAV 12
TROUBLESHOOTING
ActionCause
Problem
1. Reset the fuse
2. Allow the machine to cool down approximately
5 minutes; if the machine does not start again
automatically, contact the Service Dept.
1. Replace bag-type filter.
2. Clean suction hose.
3. Clean and replace filter element.
1. Empty tank.
1. The fuse or plug socket has blown.
2. Overload protection switch has tripped.
1. Bag-type filter full.
2. Suction hose clogged.
3. Filter element clogged.
1. Tank full (float switch closing off the
suction opening).
Motor does not start.
Reduced suction power.
No suction power during
wet cleaning.
MAINTENANCE AND REPAIR
CAUTION: Before cleaning and servicing the
machine, always remove the power cord.
Carry out only maintenance operations described in
these operating instructions. Use only original Clarke
service parts.
CAUTION: Do not make any technical
modifications to the machine. Your safety
could be endangered as a result!
For all other maintenance and repair work,
please contact and authorized service
department.
Replacing The Filter Element
1. Switch off the machine and pull the plug of the
power cord out of the plug socket.
2. Remove the machine top section from the dirt tank
and place to one side with the filter element facing
upwards (Figure 5).
3. Unscrew the filter retaining nut (1) and remove
together with the retaining washer (2).
4. Pull off the filter element (3).
5. Push on a new filter element.
6. Fit the filter retaining washer and tighten the
retaining nut.
7. Dispose of the used filter element in accordance
with the local waste disposal regulations.
Figure 5
EN
ENGLISH
Clarke
®
American Sanders Operator's Manual (EN) - CAV 12 - 7 -
NOTES
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page -19-
Clarke
®
American Sanders Operator's Manual - CAV 12
Section II
Parts and Service
(71073A)
Page -20- Clarke
®
American Sanders Operator's Manual - CAV 12
Assembly Drawing #1 4/06
1
2
4
10
3
6
5
9
8
7
Ref. Part No. Description Qty
1dooH3070002031
1eldnaH8360002032
3 909100084 1041x6M,wercS
4 302000380 1kooHelbaC
5 302000378 1oxBhctiwS
6 302000612 1hctiwS
7 18274 121x4M,wercS
1obnK1320019098
9 9868 15.2x01,gniR-O
10 302000382 Hose Hanger (optional accessory)
11 1Label
302002531
NI 302000435 1elbaC rewoP
Page -21-
Clarke
®
American Sanders Operator's Manual - CAV 12
Assembly Drawing #2 4/06
Ref. Part No. Description Qty
1 302000372 Base 1
2 302000637 Tank Gasket 1
3 302000460 Filter Gasket 1
4 26785 Vacuum Mot 1
5 26774 Carbon Brush Set 1
6 28875 Motor Bearing Ring Set 1
7 302000755 Terminal Block 1
8 302000371 Clamping Plate 1
9 302000373 Air Duct 1
10 47035 Sleeve 1
11 11256 Screw, 3.5 x 18 2
12 5697 Strap, 3 x 8 x 33 1
13 909100138 Screw, 5 x 20 MP 3
14 302000490 Filter Element 1
15 302000472 Filter Support 1
16 302000379 Deflector 1
17 61174 Static Strap 1
18 61156112 Filter Liner 1
1
3
2
4
17
18
16
13
15
14
6
5
11
10
9
11
12
13
7
8
Page -22- Clarke
®
American Sanders Operator's Manual - CAV 12
Assembly Drawing #3 4/06
Ref. Part No. Description Qty
1 302002528 Tank, CAV 12 1
2 302000349 Latch 2
3 302000682 Caster 2
4 909100164 Screw 2
5 302000636 Axle 1
6 909100085 Screw, 50 x 35 1
7 30637A Wheel 2
8 53857A Ring, Clamping 2
9 53856A Tank Liner 1
10 302000527 Filter Bag (optional accessory 5 pcs.)
9
2
3
4
3
4
6
5
7
8
2
10
1
Clarke
®
Operator's Manual - Focus Rider Scrubber Page -127-
CLARKE PRODUCT SUPPORT BRANCHES
PRODUCTION FACILITIES
ALTO Danmark A/S, Aalborg
Blytaekkervej 2
DK-9000 Aalborg
+45 72 18 21 00
ALTO Danmark A/S, Hadsund
Industrikvarteret
DK-9560 Hadsund
+45 72 18 21 00
SALES SUBSIDIARIES
ALTO US - Canada, Ontario (Canada)
4080 B Sladeview Crescent Unit 1
Mississauga, Ontario L5L 5Y5
(905) 569 0266
ALTO Overseas Inc., Sydney (Australia)
1B/8 Resolution Drive
Caringbah NSW 2229
+61 2 9524 6122
ALTO Cleaning Systems Asia Pte Ltd., Singapore
No. 17 Link Road
Singapore 619034
+65 268 1006
ALTO Deutschland GmbH, Bellenberg (Germany)
Guido-Oberdorfer-Straße 2-8
89287 Bellenberg
+49 0180 5 37 37 37
ALTO Cleaning Systems (UK) Ltd., Penrith
Gilwilly Industrial Estate
Penrith
Cumbria CA11 9BN
+44 1768 868 995
ALTO France S.A. Strasbourg
B.P. 44, 4 Place d’Ostwald
F-67036 Strasbourg
Cedex 2
+33 3 8828 8400
ALTO Nederland B.V.
Postbus 65
3370 AB Hardinxveld-Giessendam
The Netherlands
+31 184 677 200
ALTO Sverige AB, Molndal (Sweden)
Aminogatan 18
Box 4029
S-431 04 Molndal
+46 31 706 73 00
ALTO Norge A/S, Oslo (Norway)
Bjornerudveien 24
N-1266
+47 2275 1770
U. S. A. Locations European Locations
CORPO
PRODUCTION FACILITIES
Clarke
®
, Springdale, Arkansas
2100 Highway 265
Springdale, Arkansas 72764
(479) 750-1000
Customer Service - 1-800-253-0367
Technical Service - 1-800-356-7274
SERVICE FACILITIES
Clarke
®
, Elk Grove, Illinois 60007
2280 Elmhurst Road
(847) 956-7900
Clarke
®
, Denver, Colorado 80204
1955 West 13th Ave.
(303) 623-4367
Clarke
®
, Houston, Texas 77040
7215 North Gessner Road
713-937-7717
SERVICE AND SALES FACILITY
American Lincoln
®
/ Clarke, Madison Heights,
Michigan 48071-0158
29815 John R.
(810) 544-6300
American Lincoln
®
/ Clarke, Marietta, Georgia 30066
1455 Canton Road
(770) 973-5225
Clarke
®
Clarke American Sanders
A.L. Cook
Customer Service Headquarters and Factory
2100 Highway 265
Springdale, Arkansas 72764
(479) 750-1000
Technical Service
1-800-356-7274
Page -24- Clarke
®
American Sanders Operator's Manual - CAV 12
Clarke
®
American Sanders U. S. Warranty
This Clarke American Sanders Industrial/Commercial Product is warranted to be free from defects in
materials and workmanship under normal use and service for a period of two years from the date of pur-
chase, when operated and maintained in accordance with Clarke American Sanders's Maintenance and
Operations instructions.
This warranty is extended only to the original purchaser for use of the product. It does not cover normal
wear parts such as electrical cable, rubber parts, hoses and motor brushes.
If difficulty develops with the product, you should:
(a). Contact the nearest authorized Clarke American Sanders repair location or contact the Clarke American
Sanders Service Operations Department, 2100 Highway 265, springdale, Arkansas, for the nearest autho-
rized Clarke American Sanders repair location. Only these locations are authorized to make repairs to the
product under this warranty.
(b). Return the product to the nearest Clarke American Sanders repair location. Transportation charges to
and from the repair location must be prepaid by the purchaser.
(c). Clarke American Sanders will repair the product and or replace any defective parts without charge within
a reasonable time after receipt of the product.
Clarke American Sanders's liability under this warranty is limited to repair of the product and/or replace-
ment of parts and is given to purchaser in lieu of all other remedies, including INCIDENTAL AND CONSE-
QUENTIAL DAMAGES.
THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE SPECIFIED HEREIN. THERE ARE NO
WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION OF THE FACE HEREOF. NO WARRANTIES,
INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY, SHALL BE IMPLIED. A warranty
registration card is provided with your Clarke American Sanders product. Return the card to assist Clarke
American Sanders in providing the performance you expect from your new floor machine.
Clarke, 2100 Highway 265, Springdale, Arkansas 72764.
Clarke American Sanders reserves the right to make
changes or improvements to its machine without notice.
Always use genuine Clarke American Sanders Parts for repair.
2100 Highway 265
Springdale, Arkansas, 72764
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
Clarke CAV12 is especially designed for fine dust pick-up produced while grinding wood or gypsum, which makes it ideal for construction sites or workshops. It has a powerful motor that provides 127 CFM airflow for efficiently cleaning up even the finest dust particles, leaving the surfaces spotless. The 12-gallon tank offers ample capacity for extended cleaning sessions without the need for frequent emptying.
The triple-layer filtration system ensures maximum dust capture and prevents fine particles from escaping back into the air, contributing to a cleaner and healthier work environment. The tank liner's synthetic linen material allows for effortless dust removal, while the filter liner traps finer particles and the primary filtering element handles the ultra-fine ones. Cleaning and maintaining the filters is simple, ensuring optimal performance over time.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- français: Clarke CAV12 Manuel utilisateur
- español: Clarke CAV12 Manual de usuario
