Freestyle FS 1064 User manual

Freestyle
Brand
Freestyle
Model
FS 1064
Category
Sport watches
Type
User manual

This manual is also suitable for

Freestyle- Gromatide Instruction
30/01/2010
FS 1064 Gromatide AG7027-INST-R01
2741
AG7027
27/01/2010
GROMATIDE
FEATURES:
• Tidedatafor75beachesworldwide
• 180minuteoffset
• Displayspresentandfuturetidedata
• 9programmablefavoritelocations
• Optionalbigtimewithsharkn
animation
• 100metersH20
SPECIAL FEATURE
ThisFreestyleproductfeaturesunique
HydroPushers®:thesepusherscanbe
pressedunderwatertoadynamicwater
pressure(notwaterdepth)of3ATM.
CONTROL BUTTONS
S1:StartButton
S2:Stop/ResetButton
S3:ModeButton
S4:SetButton
S5:LightButton
DISPLAY MODE
Thewatchhassixdisplaymodes:NORMAL
TIME,TIDE,CHRONO,TIMER,HEATTIMER
andALARM.
Tochangefromonedisplaymodeto
another,pressS3buttononce.
NOTE:Inanysettingmode,ifthereisno
manipulationforabout120seconds,the
watchwillautomaticallyexitthesetting
procedure.
TO SET THE TIME AND CALENDAR
1. PressS3buttontoselectNORMALTIME
mode.
2. PressandholdS4buttonfortwosec-
ondsuntilthe“SET”messageappears
andtheTimeZoneblinksonthedisplay.
3. PressS1buttonorS2buttontotoggle
betweenTimeZone1andTimeZone2.
4. PressS3buttononce,theHourdigits
(includingAM/PMfor12-hourformat)
willblink.
5. PressS1buttontoincreasethedigitsby
oneunit,orpressS2buttontodecrease
thedigitsbyoneunit.Holdingdown
eitherbuttonwillspeeduptheprocess.
6. PressS3buttononce,theMinutedigits
willblink.
7. PressS1buttonorS2buttontosetthe
Minutedigits.
8. PressS3buttononce,theSeconddigits
willblink.
9. PresseitherS1buttonorS2buttonto
settheSeconddigitstozero.
10.PressS3buttononce,theMonthdigits
willblink.
11.PressS1buttonorS2buttontosetthe
Monthdigits.
12.PressS3buttononce,theDatedigits
willblink.
13.PressS1buttonorS2buttontosetthe
Datedigits.
14.PressS3buttononce,theYeardigits
willblink.
15.PressS1buttonorS2buttontosetthe
Yeardigits.
16.PressS3buttononce,theTimeFormat
willblink.
17.PressS1buttonorS2buttontotoggle
between12-hourand24-hourTime
Format.
18.PressS3buttononce,theDateFormat
willblink.
19.PressS1buttonorS2buttontocycle
amongMM-DD-YY(month-date-year),
DD-MM-YY(date-month-year)andYY-
MM-DD(year-month-date)tosetthe
DateFormat.
20.PressS3buttononce,theDay(ofthe
week)Languagewillblink.
21.PressS1buttonorS2buttontocycle
amongEnglish,French,Portugueseand
SpanishtosettheDayLanguage.
22.PressS3buttononce,theHourlyChime
statuswillblink.
23.PressS1buttonorS2buttontotoggle
betweenONandOFFofHourlyChime.
24.PressS3buttononce,theButtonBeep
statuswillblink.
25.PressS1buttonorS2buttontotoggle
betweenONandOFFofButtonBeep.
26.PressS3buttononce,theBigTimeOp-
tionstatuswillblink.
27.PressS1buttonorS2buttontotoggle
betweenONandOFFofBigTimeOp-
tion.
28.PressS3buttononce,theTideHeight
unitwillblink.
29.PressS1buttonorS2buttontotoggle
betweenfeetandmetersforTideHeight
unit.
30.Afternishedmakingallthesettings,
pressS4buttontoconrmthesettings.
NOTE:Thedateisdisplayedinthecurrent
DateFormat,butthesettingsequence
shallalwaysbemonth,date,andthenyear,
regardlessoftheDateFormatchosen.
NOTE:Theavailabledaysofthemonth
shallbedeterminedbythemonthsetting.
IfFebruaryisset,theavailabledaysofthe
monthshallbe1to29.IfFebruary29isset
forayearthatisnotaleapyear,thedate
shallbecorrectedtoFebruary28uponexit
fromthesettingprocedure.
NOTE:ForBigTimeOption,ifOFFis
selected,onlydate/timeandtide/time
formatswillbeavailableinNORMALTIME
mode;ifONisselected,theBigTime
displayformatshallalsobeavailablein
NORMALTIMEmode.
NOTE:TheTimeFormatandDateFormat
settingsapplyonlytotheselectedTime
Zone;whilethesettingsofDayLanguage,
HourlyChime,ButtonBeep,BigTime
OptionandTideHeightunitapplytoboth
TimeZones.
DIFFERENT DISPLAY FORMATS IN
NORMAL TIME MODE
Therearethreedisplayformatsineach
TimeZoneinNORMALTIMEmode:date/
time,tide/timeandbigtime.
TochangefromoneTimeZonetoanother,
pressS2buttononce.
Tochangefromonedisplayformatto
another,pressS1buttononce.
Indate/timedisplayformat,
theprimarytimedayanddateareshown
inthetopofthedisplay;thetimeinhours,
minutesandsecondsisshowninthebot-
tomofthedisplay.Thedataisshowninthe
DateandTimeFormatsofthedisplayed
TimeZone,whicharesetinthismode
alongwiththedateandtime.
Ifthereispreviousandupcomingtidedata,
theleft-handpartofthedisplayshows
thetidestatusforthecurrentlyselected
tidelocation.Otherwise,nographicis
displayed.
Intide/timedisplayformat,
thedisplayisidenticaltothedate/time
formatexceptthatthenexttide(highor
low)forthecurrentlyselectedtidelocation,
thetimeofthenexttide,anditsheightare
showninplaceofthedayandthedate.The
tidetimeisshowninthesameformatas
theprimarytime.TheTideHeightisshown
inthecurrentTideHeightunitselected.
Ifnopreviousorupcomingtidedatais
available,thisformatshallbeunavailable
andtheformatshallreverttodate/time.
Inbigtimedisplayformat,
onlythehoursandminutesoftheprimary
timeareshown,noAM/PMindication.
Asharknanimationshalloccuronceper
minutes.Forevenminutes,thenshall
movefromlefttorightonedotcolumnat
atime,andforoddminutes,thenshall
movefromrighttoleft.
Thebigtimedisplayformatisincludedonly
iftheBigTimeOptionison.
NOTE:Thecurrenttidelevelanddirection
(risingorfalling)shallbepresentedbya
tidestatusgraphic,whichisrepresentedby
anarrowheadtwodotshighandthreedots
wide.Thestepsshallappearasfollows:
Indisplays1through10,thetideisrising;
whileindisplays11through20,thetide
isfalling.Whenthetimeofdayadvances
totheminuteafterthetimeofhightide,
display11isshown;whenthetimeofday
advancestotheminuteafterthetimeof
lowtide,thesequencerepeatsbeginning
withdisplay1.
TO USE TIDE DATA
Fordisplayingtideinformationofcurrent
timeandlocation,
1.PressS3buttontoselectTIDEmode.
Thefavoritenumberandthenameof
currenttidelocationwillappear.
2.Aftertwoseconds,thenextupcoming
tide(highorlow),baseontheprimary
time,forthecurrenttidelocationwill
bedisplayed.Thedatewillbedisplayed
inthetopline,thenexttidewillbedis-
playedinthemiddlelinefollowedbythe
timeofthattide(withasuperscriptA/P
representingAM/PMin12-hourformat),
andtheheightofthenexttidewillbe
displayedinthebottomline(including
minussignifnecessary).
3.PressS1orS2buttontodisplaythe
previousandnexttiderespectively.
4.PressandholdS1buttonorS2button
untilthe“SCAN”messageappearsto
initiatedatescanningintheforwardor
backwarddirectionrespectively.
5.Releaseeitherbuttonwhenthedesired
dateisdisplayed.
6.Afterabandoningthedatescanning
procedure,whilethe“SCAN”messageis
stilldisplayed,pressS1buttonorS2
buttontomoveforwardorbackward
respectivelythedisplayeddatebyone
day.Pressandholdthecorrespond-
ingbuttonstoreinitiatedatescanning.
NOTE:Ifnopreviousorupcomingtidedata
isavailable,thesentence“NOTIDEDATA
FORDATE”willbedisplayed.
NOTE:Thedate,timeandtideheightunit
willbedisplayedintheformatsofthe
primarytimesetinNORMALTIMEmode.
NOTE:IfthedisplayedtimerepresentsDST
(daylightsavingstime),whichmeansthat
thetimewasadjustedfromthestoredtide
data,theDSTagwillappear.
NOTE:Scanningshallstopautomatically
ifthelastdateforwhichthereistidedata
isreached.
Forsettingtidelocation,
1. PressS3buttontoselectTIDEmode.
Thefavoritenumberandthenameof
currenttidelocationwillappear.
2. PressS4button,the“SET”messageap-
pearsandtheFAV(favorite)number
blinksonthedisplay.Thedefaultfavor-
ENGLISH ENGLISH
Freestyle- Gromatide Instruction
30/01/2010
FS 1064 Gromatide AG7027-INST-R01
2741
AG7027
27/01/2010
itenumberistheoneforthecurrent
location.
3. PressS1buttonorS2buttontomove
forwardorbackwardrespectivelythe
favoritenumberandthereforethecorre-
spondinglocationnametobeselected.
4. PressS3button,thegeographicalRE-
GIONwillblink.
5. PressS1buttonorS2buttontomove
forwardorbackwardrespectivelythe
REGIONtobeselected.
6. PressS3button,thegeographicalLOCA
TIONwillblink.
7. PressS1buttonorS2buttontomove
forwardorbackwardrespectivelythe
LOCATIONtobeselected.
8. PressS3button,theDST(daylightsav-
ingstime)statuswillblink.
9. PressS1buttonorS2buttontomove
forwardorbackwardrespectivelythe
DSTstatustobeselected.IfAUTOisse-
lected,thewatchshalldeterminewhen
thelocationisonDST;
ifOFForONisselected,theDSTstatus
isforcedtotheselectedstatusallthe
time.PleasenotethatthecurrentDST
statusisshownwiththeDSTag.
10.PressS3button,thecustomlocation
selectionwillblink.
11.PressS1orS2buttontotogglebetween
YESandNO.IfNOisselected,thatstep
istheendofthesettingsequence.Oth-
erwise,thesequencecontinuestoallow
settingthetimeoffsettothetidedata
andthe16charactersofthecustom
locationname.
12.PressS3button,thetimeoffset(inthe
unitofminutes)tothetidedataforthe
customlocationwillblink.
13.PressS1buttonorS2buttontoincrease
ordecreaserespectivelythetimeoffset
(theavailableoffsetsare-180,-170,…,
-10,0,+10,…,+170,+180minutes).The
offsethasnoimpactontheDSTstatus.
14.PressS3button,therstcharacterof
the16-charactercustomlocationname
willblink.
15.PressS1buttonorS2buttontocycle
forwardorbackwardrespectivelythe
selectedcharacter.PressS3buttonto
proceedtothenextcharacter.
16.Afternishedmakingallthesettings,
pressS4buttontoconrmthesettings.
TO USE THE CHRONOGRAPH
Forthemeasurementofelapsedtime,
1.PressS3buttontoselectCHRONO
GRAPHmode.
2.PressS1buttontostartcounting.
3.Tostopcounting,pressS2button.Press
S1buttontoresumefromwhereitleft
off.
4.Toresettozero,pressS2buttononce
tostopcountingandthenpressS2but-
tonagain.
NOTE:Forthersthour,theCHRONOtime
isdisplayedintheMM.SShh(minutes.
secondhundredths)format.Afteronehour,
theCHRONOtimeisdisplayedinHH:MM
SS(hours:minutes.seconds)format.
NOTE:TheCHRONOcancountup
toamaximumtimeof99:59.59
(99hours:59minutes.59seconds).
TO SET THE TIMER
1. PressS3buttontoselectTIMERmode.
2. PressS4button,the“SET”message
appearsandtheHourdigitsblinkonthe
display.
3. PressS1buttontoincreasethedigitsby
oneunit,orpressS2buttontodecrease
thedigitsbyoneunit.Holdingdown
eitherbuttonwillspeeduptheprocess.
4. PressS3buttononce,theMinutedigits
willblinkonthedisplay.
5. PressS1buttonorS2buttontosetthe
Minutedigits.
6. PressS3buttononce,theSeconddigits
willblinkonthedisplay.
7. PressS1buttonorS2buttontosetthe
Seconddigits.
8. PressS3buttononce,theactiontobe
takenattheendofacountdownwill
blink.
9. PressS1buttonorS2buttontotoggle
betweenSTOPandREPEAT.IfSTOPis
selected,theTIMERstops;ifREPEATis
selected,theTIMERrepastsitscount
downfor99times.
10.Afternishedmakingallthesettings,
pressS4buttontoconrmthesettings.
NOTE:TheTIMERcancountup
toamaximumtimeof23:59.99
(23hours:59minutes.59seconds).
TO USE THE TIMER
1.PressS3buttontoselectTIMERmode.
2.PressS1buttontostartacountdown.
3.Tostopcounting,pressS2buttononce.
PressS1buttontoresumefromwhereit
leftoff.
4.ToresettheTIMER,pressS2buttononce
tostopcountingandthenpressS2but-
tonagain.
5.Uponcompletionofacountdown,if
STOPisselectedastheactiontobe
taken,theTIMERstopsatzero,atune
willbeemittedandthebacklightwill
ash;ifREPEATisselected,theTIMER
repeatsitscountdownwiththerep
numberupdated.IftheTIMERreset
timeislessthan30seconds,abeepwill
beemitted.Otherwise,atunewillbe
emittedandthebacklightwillash.
TO SET THE HEAT TIMER
1.PressS3buttontoselectHEATTIMER
mode.
2.PressS4button,the“SET”message
appearsandtheMinutedigitsblinkon
thedisplay.
3.PressS1buttontoincreasethedigits
byveunits,orpressS2buttonto
decreasethedigitsbyveunits.Holding
downeitherbuttonwillspeedupthe
process.
4.Afternishedmakingallthesettings,
pressS4buttontoconrmthesettings.
NOTE:TheHEATTIMERcancountuptoa
maximumtimeof35.00(35minutes).
TO USE THE HEAT TIMER
1.PressS3buttontoselectHEATTIMER
mode.
2.PressS1buttontostartacountdown.
3.Tostopcounting,pressS2buttononce.
PressS1buttontoresumefromwhereit
leftoff.
4.ToresettheHEATTIMER,pressS2but-
tononcetostopcountingandthenpress
S2buttonagain.
5.Uponcompletionofacountdown,atune
willbeemittedandthebacklightwill
ash.
NOTE:TheHEATTIMERisindependent
oftheTIMER.Bothmayberunningatthe
sametime.
TO SET THE ALARM TIME
1. PressS3buttontoselectALARMmode.
2. PressS4button,the“SET”messageap
pearsandthealarmentrytosetblinks
onthedisplay.
3. PressS1buttonorS2buttontotoggle
betweenALARM1andALARM2.
4. PressS3button,theHourdigits(includ
ingAM/PMfor12-hourformat)will
blink.
5. PressS1buttontoincreasethedigitsby
oneunit,orpressS2buttontodecrease
thedigitsbyoneunit.Holdingdown
eitherbuttonwillspeeduptheprocess.
6. PressS3button,theMinutedigitswill
blink.
7. PressS1buttonorS2buttontosetthe
Minutedigits.
8. PressS3button,thealarmfrequency
willblink.
9. PressS1buttonorS2buttontocycle
forwardorbackwardrespectivelythe
alarmfrequencytobeselected(DAILY,
WEKDAYS,WEEKENDS,dayofthe
weekandWKLY).
10.Afternishedmakingallthesettings,
pressS4buttontoconrmthesettings.
NOTE:TheALARMTIMEdisplayedisinthe
sameTimeFormatastheprimarytime.
NOTE:Atunewillgooffandthebacklight
willashfor20secondsatthedesignated
timewhentheALARMisactivated.
NOTE:Thealarmwillautomaticallybe
activatedafterbeingset.
WHEN AN ALARM OR HOURLY CHIME
GOES OFF
AtunewillgooffbythehouriftheHourly
Chimefunctionisactivatedandthesame
willhappenatthedesignatedtimewhen
theALARMisactivated.Tostopthetune,
pressanybutton.
Ifthealarmtuneisdonewithoutanyuser
interruption,thewatchwillautomatically
enterasnoozemode.TheALARMwillgo
offagainafter5minutesbutforonlyonce.
TO USE THE BACKLIGHT
PressS5buttontoturnonthebacklightfor
threeseconds.
Toreducecarbonfootprint,these
Freestyleinstructionsareprintedwith
soyinksonrecycledpaper.
ENGLISH ENGLISH
FS1064-GROMATIDE-AG7027-R01
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Freestyle- Gromatide Instruction
30/01/2010
FS 1064 Gromatide AG7027-INST-R01
2741
AG7027
27/01/2010
WEST CST USA
Huntingt Huntington Beach, CA
Trestles Trestles, San Clemente, California
Oceansd Oceanside, California
La Jolla La Jolla, California
Humboldt Humboldt Bay, California
Ocean B. Ocean Beach, outer coast
Mvricks Mavericks, California
St. Cruz Santa Cruz, California
Morro B. Morro Bay, California
Pismo B. Pismo Beach, California
Gaviota Gaviota, California
Rincon Rincon, California
Ventura Ventura, California
Malibu Malibu, California
Redondo Redondo Beach, California
Anchorag Anchorage, Alaska
Elliot B Seattle, Washington
Seaside Seaside, Oregon
Newport Newport, Oregon
EAST CST USA
Sebastn Sebastian Inlet, Florida
N. Miami North Miami Beach, Florida
St. Aug St. Augustine Beach, Florida
Hamptn H Hampton Harbor, New Hampshire
Nauset H Nauset Harbor, Cape Cod,
Massachusetts
Montauk Montauk Point, Long Island Sound,
New York
Manasqn Manasquan Inlet, USCG Station,
New Jersey
Atlantic Atlantic City (Steel Pier), New Jersey
Ocean Ct Ocean City (shing pier), Maryland
Rehoboth Rehoboth Beach, Delaware
Virginia Virginia Beach, Virginia
C. Hattrs Cape Hatteras, North Carolina
Wrightsv Wrightsville Beach, North Carolina
Myrtle Myrtle Beach, South Carolina
HAWAII USA
Haleiwa Haleiwa, Oahu Island, Hawaii
Hanalei Hanalei Bay, Kauai Island, Hawaii
Banyans Banyans, Big Island, Hawaii
Ma’alaea Ma’alaea, Maui Island, Hawaii
Lahaina Lahaina, Maui Island, Hawaii
Sandy B Sandy Beach, Oahu Island, Hawaii
GULF CST USA
Pnma Cty Panama City Beach, Florida
Naples Naples Pier, Florida
Galvestn Galveston (Pleasure Pier), Texas
Corp Chr Corpus Christi, Texas
ISLANDS CARIBB
San Juan San Juan, Puerto Rico
Bdgetown Bridgetown, Barbados
CANADA
Tono Tono, British Columbia
MEXICO
Prt Escn Puerto Escondido, Oaxaca, Mexico
Mazatlan Mazatlán, Sinaloa, Mexico
Ensenada Ensenada, Baja California Norte, Mexico
WATCH DISPLAY LOCATION
VISUALIZACIÓN LUGAR
UHRANZEIGE STANDORT
AFFICHAGE SUR LA MONTRE EMPLACEMENT
DISPLAY OROLOGIO LUOGO
MOSTRADOR DE RELÓGIO LOCAL
時計のディスプレイロケーション
Freestyle- Gromatide Instruction
30/01/2010
FS 1064 Gromatide AG7027-INST-R01
2741
AG7027
27/01/2010
WATCH DISPLAY LOCATION
VISUALIZACIÓN LUGAR
UHRANZEIGE STANDORT
AFFICHAGE SUR LA MONTRE EMPLACEMENT
DISPLAY OROLOGIO LUOGO
MOSTRADOR DE RELÓGIO LOCAL
時計のディスプレイロケーション
CENTRAL AMERICA
Pta Arns Punta Arenas, Costa Rica
Cristobl Cristóbal, Panama
Libertad La Libertad, El Salvador
PACIFIC ISLANDS
Teahup. Teahupoo, Tahiti
Tavarua Tavarua, Fiji
GUAM
Agana Agana, Guam
AUSTRLIA
Sydney Sydney Beaches, Australia
Bells B. Bells Beach, Australia
Marg Rvr Margaret River, Australia
Phlp Isl Phillip Island, Australia
Newcastle Newcastle, Australia
NEW ZEALAND
Raglan Raglan, New Zealand
Hobart Hobart, Tasmania
SOUTH AMERICA
Rio de J Rio de Janeiro, Brazil
Floriano Florianópolis, Brazil
EUROPEAN
Bordeaux Anglet
Ferrol El Ferrol Del Caudillo, Spain
Newquay Imham, UK
Portrush Portrush, Northern Ireland
Canary Canary Island
ASIA
Bali Bali, Indonesia
Le Port Le Port, Reunion Island
Muroto Muroto
Irago Irago
Maizuru Maizuru
SOUTH AFRICA
Durban Durban, South Africa
Toreducecarbonfootprint,these
Freestyleinstructionsareprintedwith
soyinksonrecycledpaper.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Freestyle FS 1064 User manual

Freestyle
Brand
Freestyle
Model
FS 1064
Category
Sport watches
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents