Tripp Lite B004-008 Owner's manual

Owner’s Manual

NOTE: Follow these instructions and operating procedures to ensure correct performance and to prevent damage to this unit

or to its connected devices.

8-Port Standard

KVM Switch

Model #: B004-008

WARRANTY

REGISTRATION

Register online today for a chance

to win a FREE Tripp Lite product!

www.tripplite.com/warranty

Tripp Lite World Headquarters

1111 West 35th Street, Chicago, IL 60609 USA

+1.773.869.1234 • www.tripplite.com

Features 2

Hardware Requirements 2

Console 2

PC 2

Cables 2

Controls and Connections 3

Front View 3

Rear View 3

Mounting and Stacking Instructions 4

Installation 4

Operation 5

Hot Plugging 5

Powering Off and Restarting 5

Port Selection 5

Hot Key Operation 6

Troubleshooting 6

Speciﬁcations 7

FCC Radio/TV Interference Notice 8

Warranty and Warranty Registration 8

Español 9

Français 17

Table of Contents

2

Control Up to 8 PCs from a Single Console (Keyboard, Monitor and Mouse)•

No Software Required - PC Selection done via Front Panel Switches or Hot Keys•

Quick View Scan Mode for Monitoring Selected PCs•

PS/2 and Serial Mouse Emulation Provided for System Bootup•

Console’s PS/2 Mouse Controls All Connected PCs•

Microsoft Intellimouse Pro, Logitech FirstMouse, FirstMouse+ Support*•

SVGA, VGA and Multisync Monitor Support•

LED Display for Easy Status Monitoring•

Rack Mountable in 19” System Rack•

Hot Pluggable - Add or Remove PCs for Maintenance Without Powering Down the Switch•

Superior Video Quality: 1920x1440; DDC2B.•

* 1. PS/2 compatible mouse support is for three button (wheel) mice.

2. The Change Device procedure in the Logitech Mouse Ware program does not work in Microsoft NT.

Features

Hardware Requirements

A VGA, SVGA, or Multisync monitor capable of the highest resolution that you will be •

using on any of the PCs.

A PS/2 Style Mouse•

A PS/2 Style Keyboard•

Each PC must have:

A VGA, SVGA, Multisync card or USB port.*•

A 6-pin mini-DIN (PS/2 style).•

Either a 6-pin mini-DIN (PS/2 Style) keyboard port or a USB port.*•

The following are the cables needed to connect your KVM Switch to the CPUs:

P750-006 PS/2 Cable Kit – 6’

P750-010 PS/2 Cable Kit – 10’

P750-015 PS/2 Cable Kit – 15’

NOTE: The wiring and pin assignments will not let you use a Serial-to-PS/2 adapter at the KVM side of the cable.

Attempting to use a standard serial extender cable with adapters at both ends will fail.

* Use a B015-000 PS/2 to USB Adapter to connect a USB computer to the KVM (still requires a P750 series cable kit to

complete CPU connection).

Console

PC

Cables

3

1

3

21

Controls and Connections

1

Lighted Port Selection Button

Lights GREEN to indicate which ports have been selected. •

Lights RED to indicate which ports are connected to a computer and powered on. •

An unlit button indicates that no computer is connected or that the connected computer •

is not powered on.

A flashing button indicates which port is currently selected in the auto-scan mode.•

1

Power Jack

The optional power adapter plugs in here. The switch is designed to be non-powered

(no external power required). It draws the necessary power from the connected CPUs

through the Keyboard/Mouse connection. External power is required if the CPUs do not

provide sufficient power (operation will be erratic).

2

Console Port Section

Your monitor, keyboard and mouse plug in here.

3

CPU Port Section

The cables from the PCs plug in here.

Front View

Rear View

4

For convenience in large installations, the unit is supplied with the necessary hardware for rack

mounting in a 19” (1U) system rack, or stacked.

For Rack Mounting:

Screw the mounting brackets into the sides of the unit.1.

Slide the unit into the rack and secure it to the rack.2.

Make sure that power to all the devices (KVM Switch and PCs) you will be connecting have

been turned off.

Plug the monitor, keyboard, and mouse into the Console Ports1.

Use Tripp Lite P750 Series Cable Kits to connect each PC’s monitor, keyboard and mouse 2.

ports to one set of the KVM ports.

If you choose to use external power, connect the supplied adapter to the power socket on 3.

the KVM switch and then plug the adapter into an AC power source. The unit is designed

for non-powered operation (it draws power from the computers via the keyboard and

mouse cables). If a computer only supplies 3.3V of power for the keyboard and mouse

instead of 5V (as in the case of Notebooks), you will need to use the external power

adapter.

NOTE: If you choose to use external power, the unit must be plugged in and receiving power prior to Step 4.

Turn on the power to the PCs.4.

Installation

Mounting and Stacking Instructions

5

Operation

Components can be removed and added back into the installation by unplugging their cables

from the unit’s ports without shutting the switch down. The following procedures must be

performed in order for hot plugging to work:

Hot Plugging CPU Ports:•

When hot plugging cables from the CPU ports:

The cable must be plugged back into the same port it was removed from.A.

The mouse cable must be plugged in before the keyboard cable.B.

Hot Plugging Console Ports:•

Simply unplug the Keyboard, Mouse or Monitor and plug in a new one.

NOTE: When hot plugging the mouse from the KVM Switch’s console mouse port:

The mouse may be removed and replaced (to reset the mouse, for example), as long as 1.

it is the same mouse.

If you plug in a different mouse, all the computers must be shut down for 10 seconds, 2.

then restarted.

If it is necessary to Power Off the KVM Switch, do the following before restarting it:

Shut down all the computers. 1.

NOTE: A. Unplug the power cord of any PC (connected to the KVM) that has the

Keyboard Power On function.

B. If the unit is operating on external power, unplug the power adapter cable.

Wait 10 seconds, then restart the KVM Switch.2.

After the Switch is up, power ON the PCs.3.

The following methods can be used to access the B004-008 KVM Switch ports:

Manual Push Buttons•

Simply press the appropriate port selection switch on the unit’s front panel. The Selected

LED will light to indicate that the port is selected.

Hot Plugging

Powering Off and Restarting

Port Selection

6

The following are the hot key commands for your KVM (keys must be pressed sequentially).

Change to previous port: Scroll Lock + Scroll Lock + [ ]

Change to next port: Scroll Lock + Scroll Lock + [ ]

Change to a specific port: Scroll Lock + Scroll Lock + “1” to “8” (depending on desired port)

Start Auto-Scan with an interval of “X” (where “X” can be 07, 15 or 30 for 7, 15 or 30

seconds): Scroll Lock + Scroll Lock + a + “X”

Stop Auto-Scan: Press the Space bar

NOTE: If you stop scanning on an empty port, or one where the computer is attached but is powered off, the monitor

screen will be blank, and the mouse and keyboard will have no effect. To recover, key in the Hot Key sequence (see Hot

Key Selection, above), for any Port ID that has an active PC attached.

Turn “Beep” sound On/Off: Scroll Lock + Scroll Lock + S

Operation (Continued)

Hot Key Operation

Troubleshooting

Symptom Possible Cause Action

Erratic Behavior Unit not receiving power under self-

powered operation

Use the power adapter that was

provided with the units to provide

external power.

Pressing the Hot Keys does not

get a response

The connection from the selected

port to the target PC has been

broken, or the PC is turned OFF.

Check the Online LED for the

selected port. If it is not lit:

Manually press one of the Select 1.

switches to connect to a PC that

is powered ON.

Check the cables to make sure all 2.

are properly connected.

If the desired PC is OFF, 3.

power it ON

Improper KVM switch reset Turn OFF all KVM Switches and

wait 10 seconds before turning them

back ON.

NOTE: If the unit is operating in the

Selfpowered mode (without the

optional Power Adapter), you must

unplug the power cord of any

connected PC that has the Keyboard

'Power On' function, otherwise the

switch still draws power from the PC.

7

Specifications

AC Power Adapter (Optional) 100-240 VAC, 50-60 Hz, 0.5A

Power Consumption DC9V 600mA

PC Connections Direct 8

Port Selection Front Panel Push Buttons

Hot Keys

LEDs On Line 8 (Red)

Selected 8 (Green)

Connectors Console 1 x mini-DIN 6 Female (PS/2 Style Mouse)

1 x mini-DIN 6 Female (PS/2 Style Keyboard)

1 HDDB15 Female (standard VGA/SVGA)

CPU Ports 8 HDDB15 Male (standard VGA/SVGA)

Required Cables Tripp Lite P750 Series

Scan Interval (OSD Selection) 7, 15, 30 seconds

Operating Temperature 41 – 104° F

Storage Temperature -4 – 140° F

Humidity 0 – 80%RH, Noncondensing

Enclosure Metal

Weight 4.8 lbs

Dimensions (W x D x H) 17.5” x 6.5” x 1.75” (1U)

8

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursu-

ant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in accordance with the instruction man-

ual, may cause harmful interference to radio communications. Operation of this equipment in a residential area

is likely to cause harmful interference in which case the user will be required to correct the interference at his

own expense. The user must use shielded cables and connectors with this product. Any changes or modifica-

tions to this product not expressly approved by the party responsible for compliance could void the user's

authority to operate the equipment.

1-YEAR LIMITED WARRANTY

TRIPP LITE warrants its products to be free from defects in materials and workmanship for a period of one (1)

year from the date of initial purchase. TRIPP LITE’s obligation under this warranty is limited to repairing or

replacing (at its sole option) any such defective products. To obtain service under this warranty, you must obtain

a Returned Material Authorization (RMA) number from TRIPP LITE or an authorized TRIPP LITE service

center. Products must be returned to TRIPP LITE or an authorized TRIPP LITE service center with

transportation charges prepaid and must be accompanied by a brief description of the problem encountered

and proof of date and place of purchase. This warranty does not apply to equipment which has been damaged

by accident, negligence or misapplication or has been altered or modified in any way.

EXCEPT AS PROVIDED HEREIN, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED,

INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Some

states do not permit limitation or exclusion of implied warranties; therefore, the aforesaid limitation(s) or

exclusion(s) may not apply to the purchaser.

EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL TRIPP LITE BE LIABLE FOR DIRECT, INDIRECT,

SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT,

EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically, TRIPP LITE is not liable for any

costs, such as lost profits or revenue, loss of equipment, loss of use of equipment, loss of software, loss of

data, costs of substitutes, claims by third parties, or otherwise.

WARRANTY REGISTRATION

Visit www.tripplite.com/warranty today to register the warranty for your new Tripp Lite product. You'll be

automatically entered into a drawing for a chance to win a FREE Tripp Lite product!*

* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.

Use of this equipment in life support applications where failure of this equipment can reasonably be

expected to cause the failure of the life support equipment or to significantly affect its safety or

effectiveness is not recommended. Do not use this equipment in the presence of a flammable

anesthetic mixture with air, oxygen or nitrous oxide.

WEEE Compliance Information for Tripp Lite Customers and Recyclers (European Union)

Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing regulations, when

customers buy new electrical and electronic equipment from Tripp Lite they are entitled to:

• Send old equipment for recycling on a one-for-one, like-for-like basis (this varies depending on the

country)

• Sendthenewequipmentbackforrecyclingwhenthisultimatelybecomeswaste

The policy of Tripp Lite is one of continuous improvement. Specifications are subject to change without

notice.

Made in China

FCC Radio/TV Interference Notice

Warranty and Warranty Registration

200806248 93-2465

Tripp Lite World Headquarters

1111 West 35th Street, Chicago, IL 60609 USA

+1.773.869.1234 • www.tripplite.com

Page is loading ...

Tripp Lite B004-008 Owner's manual

This manual is also suitable for

Tripp Lite B004-008 Owner's manual

in other languages

Related papers

Other documents