Weed Eater 180083 Owner's manual

Brand: Weed Eater

Model: 180083

Category: Grass trimmers

Type: Owner's manual

OWNER'S MANUAL

3.8 Horsepower

9 anch

EDGER/TRIMMER

MODEL NO.

536.797470

Caution:

Read and follow all Safety

Rules and Operating

instructions before first use

of this product.

Sears, Roebuck and Co., Hoffman Estates 60179 U.S.A.

339690 3/04t96

Table of Contents 2 Service and Adjustments 13.14

Warranty 2 Storage 14-15

Safety Rules 2-3 Troubleshooting t5

Contents of Shipping Carton 4 Spanish (EspaSol) 16-30

Assembly 5-7 Edger Repair Parts 31-35

Operation 7-11 Engine Repair Parts 36-39

Maintenance 11-12 Parts OrdertnglService Back Cover

LIMITED ONE-YEAR WARRANTY ON CRAFTSMAN EDGER/TRIMMER

Forone year fromthe date of purchase, when thisCraftsman Edger/Trimmer ismain-

tained, lubricated, and tuned up according to the operatingand maintenance instruc-

tions in the owner's manual, Sears will repair, free of charge, any defect in material or

workmanship._

Ifthis Craftsman Edger/Trimmer is used for commercial or rental purposes, this war-

ranty applies for only 90 days from the date of purchase_

This warranty does not cover the following:

. Expendable items which become worn during normal use, such as spark plugs, etc.

* Repairs necessary because of operator abuse or negligence, including bent crank

shafts and the failure to maintain the equipment according to the instructionscon-

tained in the owner's manual

WARRANTY SERVICE IS AVAILABLE BY RETURNING THE CRAFTSMAN EDGER/

TRIMMER TO THE NEAREST SEARS SERVICE CENTER/DEPARTMENT IN THE

UNITED STATES. THIS WARRANTY APPLIES ONLY WHILE THIS PRODUCT IS IN

USE IN THE UNITED STATES.

This warranty gives you specific legal rights, and you may also have other rightswhich

may vary from state to state.

Sears, Roebuck and Co,, D817WA, Hoffman Estates, |L 60179

_k Look for this symbol to potnt out Important safety precautions, It means-°-

ATTENTION!!! Become alertif! Your safety is Involved.

CAUTION: Always disconnect spark

plug wire.and place wire where itcannot

contact spark plug to prevent accidental

starting when setting-up, transporting,

adjusting or making repairs,

IMPORTANT: Safety standards require

operatorpresence controls to minimize the

risk of injury. Your Edger/Trimmer is

equipped with suchcontrols, Do not attempt

to defeat the function of the operator

presence controlunder any circumstances,.

BEFORE USE

• Read the owner's manual carefully., Be

thoroughly familiar with the controls and

the proper use of the edgerttrimmer_

Know how to stop the edger/trimmerand

disengage the controls quickty_

, Do not operate the edgerltrimmer without

wearing adequate outer garments, Wear

footwear that willimprove footing on

slippery surfaces.

• Keep the area of operation clear of aft

persons, particularly small children and

pets..

• Thoroughly inspectthe area where the

edger/trimmer is to be used and remove

all foreign objects,

FUEL SAFETY

• Handle fuel withcare; itis highlyflam-

mableo

• Use an approved container.

• Check fuel supply before each use,

allowingspace for expansion as the heat

of the engine and/or sun can cause fuel to

expand,

• Fill fue! tank outdoors with extreme care.

Never fill fuel tank indoors.Replace fuel

tank cap securely and w_peupspilled

fuel.

• Never remove the fuel tank cap or add

fuel to a runningor hotengine°

• Never storefuel or edger/trimmer with

fuel inthe tank inside a buildingwhere

fumes may reach an open flame.

OPERATING SAFETY

• Never allow children or young teenagers

tooperate the edger/trimmer, Keep them

away while itis operating, Never allow

adultsto operate the edger/trimmer

withoutproper instruction,

. Do not operate this machine ifyou are

taking drugs or other medication which

can cause drowsiness or affect your

ability to operate this machine.

• Do not use this machine if you are

mentally or physically unable to operate

this machine safely, ' '

. Always wear safety glasses, or eye

Shields during'opei'ati0n .or while perform-

ing an adjustment or repair to protect

your eyes from foreign objects that may

be thrown from the adgedtrimmer.

• Do not put hands or feet near Or under

rotating parts.

• Exercise extreme caution when operating

on or crossing gravel drives, walks, or

roads. Stay alert for hidden hazards or

traffic.

• Exercise cautionto avoid slipping or

falling..

• Never operate the edger/trimmer without

proper guards, plates, or other safety

protective devices in place,

- Never operate the edger/trimmer at high

transport speeds on slipperysurfaces.

Look behind and use care when backing

• Never allow bystanders near the edger!

trimmer.

• Keep children and pets away while

operating.

• Never operate the edger/trimmer wilhout

good visibility or light.

, Do not run the engine indoors_The

exhaust fumes are dangerous, containing

CARBON MONOXIDE, an ODORLESS

and DEADLY GAS. .'

• Take all possible precautions when

leaving the edger/trimmer unattended°

Stop the engine°

. Do not overload the edger/trimmer

capacity by attempting to edge too deep

at too fast a rate.

SAFE STORAGE

Always referto the owner's manual

instructionsfor importantdetails ifthe

edger/trimmer isto be stored for an

extended period..

• Never store the edger/trimmer with fue_in

the fuel tank inside a building where

ignitionsources are present such as

water and space heaters, clothes dryers,

and the likeoAllow the engine to cool

before storing in any enclosure.

• Keep the edger/trimmer in safe working

condition. Check all fasteners at frequent

intervals for proper tightness.

REPAIR!ADJUSTMENTS SAFETY

. After strikinga foreign object, stop the

engine (motor). Remove the wire from the

spark plug, andkeep the wire away from

the plug to prevent accidental starting.

Thoroughly inspectthe edger/trimmer for

any damage, and repair the damage

before restartingand operating it,,

,; If edger_rimmer shouldstart to vibrate

abnormally, stopengine (motor) and

check inlmediatelyfor the cause.

Vibration is generally a warning of

trouble,

• Stop the blade whenever you leave the

.operating position. Also, disconnect the

spark plug wire before unclogging the

blades and when making any repairs,

adjustments, or inspections.

• When cleaning, repairing, or inspecting,

shut off the engine and make certain all

moving parts have stopped.

• Never attempt to make any adjustments

while the engine is running except when

specifically recommended by the manu-

facturer..

WARNING: The engine exhaust

from this product contains chemicals

known to the State of California to cause

cancer, birth defects or other reproductive

harm,.

WARNING: This unit is equipped

with an internal combustion engine and

should not be used on or near any unim-

proved forest-covered, brush-covered or

grass-covered land unless the engine's ex-

haust system is equipped with a spark ar-

rester meeting applicable local or state laws

(if any). if aspark arrester is used, it should

be maintained in effective working order by

the operator,

In the state of California the spark arresler

is required by law (Section 4442 of the Cali-

fornia Public Resources Code). Other

states may have similar laws. Federal laws

applyon federal lands_A spark arrestor/ Sears Authorized Service Center (See RE-

muffler isavaitabIe through yournearest PAIR PARTS section in this manual).

Contents of Parts Bag (actual size)

(4) - Hex Head Wide

Flange Screws (8) - Hex Head Nuts

5/16-18x 5/8 Inch 5/16-18

jlllIll Itll

11) - Shoulder Bolt 3/8_16 x 1AQQinch

(1) - 5/16-18 Hex Head

Wide Flange Locknut

(I) - Spacer _70Inch (t) - Hex Head Jam

(left rear wheel nut 3t8_16

assembly)

(2i - Hair Pins 1 - Cotter Pin

(1) - 112x 3t4 Inch

Flatwasher(right rear

wheel assembly)

(2) - 11t32x11/16 inch

Flatwashere (front wheel

assembly)

©i ......1

(I) - Io39 Inch long Spacer

(front wheel assembly)

(4)- Hex Head Screws

5116-18x 1-114 Inch

(1) - 5f16_18 x 3_00 Inch Hex Head Screw

Parts packed separately In carton (not shown full size)

(3) - Wheels

(1) - Lower Handle

1 - Container SAE30 oit

(1) - Upper Handle

Assembly

(1) -Control Rod 1 - Owner's Manual (not shown)

2 - Parts Bags (not shown)

_'/V_ CAUTION: Always wear safety

glasses or eye shields while assembling

Edger!Trimmer,

TOOLS REQUIRED FOR ASSEMBLY

2 - 1/2 inch Wrenches

(or adjustable wrench)

2 - 9/16 inchWrenches

(or adjustable wrenches)

2 - Adjustable Wrenches

1 - Regular Screwdriver

1- Pliers

Upper

Handle

Lever

Rod

The figure to the rightshows the Edger/

Trimmer completely assembled,

References to the right or left hand side

of the Edger/Trimmer are from the view-

point of the operator's position behind the

unit,,

TO REMOVE EDGER/'[RIMMER

FROM CARTON

. Remove the lower handle, control rod,

upper handle and packing material from

the carton.

• Remove wheels, parts bags and packing

material from the carton.

• Cut down all four corners of the carton,

• Remove packing material from around

Edger/Trimmer blade.

TO ASSEMBLE THE EDGER/

TRIMMER

NOTE: Lower handle shouldbe attached

first as itis difficult to attach lower handle

with the wheeis on.

- Place lower handle inside the Edger/

Trimmer frame as shown in top figure

and secure in place with four 5/16-18x

5/8 inch hex head wide flange screws

and four 5/1 6-18 hex head Iocknuts

found in parts bag. Hold back on the

lower handle as you tighten the screws,

Locknuts should be on the insideof the

frame as shown in middle figure of this

page°

• Attach the right rear wheel to the wheel

support rod of the Edger/Trimmer as

shown in lower figure on this page with a

1/2 x 3/4 inch flatwasher and cotter pin

found tn parts bag, Bend ends of cotter

pin,,

Handle

5116-18X 5/8 inch(_

Frame/

LowerHandle

5116-18)-_

-tHexHead ! ,

VIEW FROM RIGHT SIDE

Flatwasher Wheel _[ _

112x3/4' _ '

Pit

Cotter _

, Attach the left rear wheel tothe Edger!

Trimmer shown in figure belowwith a

3/8-16 x 1.40 inch shoulder bott,spacer

and 3/8-16 hex head jam nut found in

partsbag.

ViEWFROM INSIDELEFT REARWHEEL

Spacer

(_70inchtong)

ShoulderBolt

318-16

Jam Nut

Attach the front wheel to the Edger/

Trimmer shown in figure be!ow with a

5/t6-t8 x 3.00 inch hex head screw,two

11132x 11/16 inch flatwashers, one

spacer and a 5ti6-18 hex head wide

flange locknut found in parts bag,

VIEW FROM FRONT

5/16-18 Wide

Range Locknut

Movethe clutchlever to rearmost

NEUTRAL position and latch in,

If itis difficult to get the clutchlever into

NEUTRAL, itmay be necessary to loosen

the four screws and nuts holdingthe

lower handles to the frame as shown in

first figure on page 7, Pry up (forward) on

the handles only enough to allow the

clutchlever to freely enter the NEUTRAL

position. Re-tighten nuts and screws.

When the clutch lever is in NEUTRAL the

quill support arm should be close to the

spacer and screw behind it as shown

below.

position)

_.._. lutch

r Lever

trol

Rod

Locknuts

It132xl1/16

_atwasher

11t32xl 11t6Inch

Hex H

Screw ( Long)

5/16-18x3inches

• Place the upper handle on the lower

handle zs shown in next figure and at[gn

upper handle holesin lower handle, and

secure in place withfour 5/16-18 x 1-114

inchhex head screws and four 5/16_18

hex head locknutsfound in parts bag.

Locknuts should be to the inside of the

two handles as shown,

• The clutch lever is located on the left

hand side of upper handle when properly

Installed, Insert one end of the control rod

from left to right through the hole in the

clutch lever and attach with a hair pin

found in parts bags, See next figure,

, Place the clutch lever in the first depth

selection and insertthe other end of the

control rod through the hole in the quill

support arm. Attach with hairpin found in

parts bag_

x1-1/4

Hex Head

Screw

Handle

Quill

Arm

cer

VIEW FROM RIGHT SIDE OF UNIT

RightSide

Lower

LowerHandle

Mounting

er CHECKLIST

Before you operate and enjoy your new

Edger/Trimmer, we wishto assure that you

receive the best performance and satisfac-

tionfrom this quality pmducto

PLEASE REVIEW THE FOLLOWING

CHECKLIST:

_f Al! assembly instructions have been

comp_eteoo

,/" No remaining loose parts in carton_

,/" All fasteners have been properly inn

stalled and tightened.,

While learning how to use your Edger/

rimmer, pay extra attention to the follow-

ing important items;

_'€" Engine oil is at proper level

=Z_f Fuel tank is filled with fresh, clean,

regular UnIeaded gasoline_

JJ Become familiar with all controls-their

location and function. Operate controls

before starting engine.

KNOW YOUR EDGER/TRIMMER

READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR

EDGER/TRIMMER. Compare the illustrationswith your EDGERKRIMMER tofamiliarize

yourself withthe Ibcationof variouscontrolsand adjustments°Save this manual for future

reference.

Fast Stow Stop PrimerButton

ThrotUe

Rear

Con_olRod

VIEW OF BLADE AREA

Throttle Control - Used to controlthe en-

gine speed.

Primer Button - injectsfuel directly intothe

carburetormanifold forfaster starts.

Starter Handle - The engine on this Edger/

Trimmer is equipped with an easy pull recoil

starter°

Clutch Lever - Used to start and stop the

blade and controlthe depth of cut.

Blade Guard - Used to prevent stones or

other materialfrom being thrown at the op-

eratoro

Index Lever - Permits adjustment from the

edging (vertica})positionto trimming (hori-

zontal) position, To change position, puUthe

indexlever and rotate the quillassembly to

the desired angle or position.

Adjustable Rear Wheel - Rightrear wheel

is adjustable to level Edger/Trimmer when

edging along acurb(curb-hopping).

Adjustable Front Wheel - Front wheel is

adjustablefrom side-to-side for balance..

Also, can be adjusted down for curb-hop-

ping_

HOW TO USE YOUR EDGER

Z_ WARNING: The operation of this

Edger/Trimmer can resultin foreign objects

being thrownintothe eyes, which can cause

severe eye damage. Alwayswear safety

glasses or eye shields whileoperating the

Edger/Trimmer.

We recommend standard safety glasses or

Wide Vision Safety Mask for over your

glasses.

secondsbetweeneachpush.

. Donotuseprimerbuttonto restarta

warmengineaftera shortshutdown.

TO USE THE CLUTCH LEVER

• Start the engine and move the clutch

lever forward or down to engage the

cuttingblade.

- Select the edging depth you need.

There are 5 selections up to 2-3/4

inchesdeep_

IMPORTANT: ff verydeep edging is

required, we recommend that a shal-

low cut be made first, then cuts at

greater depths untilthe desired depth

is obtained_

TO USE THE INDEX LEVER

(TRIMMING OPERATION)

• Stop engine and disconnect the spark

plug wire from the spark plug_

- Loosen the knob shown Jnfigure below

on the front wheel arm and slide the

wheel all the way tothe right side°

• Tighten the knob securely.

Z_ CAUTION: The front wheel must be

in the extreme rightpositionto prevent the

blade from strikingwheel while in trimming

position_

TO STOP EDGER/TRIMMER

. To stop the engine, make sure the clutch

lever isall the way back or up and move

the throttlecontroilever to the STOP

ositon,

CAUTION: Never leave the Edger/

Trimmer unattended while the engine is

running,Always disengage the cuttingblade

and stop the engine,

7'0 USE THROTTLE CONTROL

• Run at fulI engine speed during normal

use.

• Push throttlecontrollever up to increase

speed; down to decrease speed.

TO USE PRIMER BUTTON

. Push primerbuttonfive times See page 7

figure for location_ Wait about two

• Pullthe index lever out of its notch as

shown below and position it in the

notch marked 90=.See figure on page 9.

• Reconnect the spark plug wire and

start the engine, Move the clutch

lever to the destred tdmming height.

,/_ CAUTION: Never leave the Edger/

Trimmer unattended while the engine is

running.Always disengage the cutting

blade and stop the engine,

INDEXLEVERIN THENOTCH MARKED"90"

TO USE CURB-HOPPING FEATURE

The adjustablefront and right rear wheel

feature permit the Edgar/Trimmer to be

used on an uneven surface such as a curb

as shown infigure below,

. Stop the engine and disconnect the

spark plug wire from the spark plug,

• Loosen the knob on the front wheel arm

bracket and slide the wheel to the best

positionto clear the curb and balance the

unit.

• Tighten the knob securely,

. Using the curb height adjust lever, lower

the front wheel to a positionthat places

the Edger/Trimmer level with the left rear

wheel on the uneven curb surface,

. Loosen tee knob on the inside rightrear

of the main frame that secures the wheel

support rod as shown below.,

• Slide the rear wheel down untilthe

Edger/Trimmer is level when the left

wheel is on the curb.

. Tighten the knob securely,

• Reconnect the spark plug wire and start

the engine. The depth of cut adjustment

isthe same as described in Edging

Operation paragraph,

Tee Knob

(Behind..

Wheel)_,

Front Wheel Arm

Rear

Support

Rod

Adjust Lever

Front

CAUTION: Keep away from the

rotating blade, The blade can cause injury

BEFORE STARTING ENGINE

PRE-USE CHECK OF CONTROLS

Ati controls shou!d be checked for proper

function before servicing or starting the

engine.,

° Move the clutch lever intoall six

positions in the selector plate, Make

sure the clutch lever snaps into all six

holes,

• Return the clutch lever to the rearmost

hole in the selector plate°

FILL/ADD OIL:

This Edger/Trimmer was shipped with a 20

ounce container of SAE30 motor oil This

oit must be added to the engine before

operating, Remove the oil fiI_cap and fill

the crankcase,, DO NOT OVERFILL,

NOTE: Engine may already containsome

residualoil Check frequentlywhen filling

the crankcase.

OIL RECOMMENDATIONS

Only use highquality detergent oil rated

with API service classificationSG, Select

the oil's SAE viscosity grade according to

your expected operating temperature

Although multi*viscosity oils (5W30, t0W30,

etc_)improve starting incold weather, these

multi-viscosity oiJswiliresult in increased oil

consumption when used above 32°F.

Check your engine oil level more frequently

to avoid possible engine damage from

runninglow on oil,

j j

Colder <€ -- )>Warmer

(( _))

5W30 SAE30

TO ADD ENGINE OIL

* Ptace the Edger/Trimmer on a level

surface.

• Remove the oil fill cap as shown in figure

on page 10,

. Fill the engine crankcase, pouring sEowiy,

Do not overfill, For approximate capacity

see PRODUCT SPECIFICATIONS chart

in this manual°

Reinstall the oil fill cap and tighten

securely

Check oil before each use Add if

needed

Change oil after the first2 operating

hours and every 25 operating hours

thereafter.

Cap

Oil Fill Cap

FILL GAS

Fill the fue! tank with clean, fresh, unleaded

grade automotive gasoline. Be sure that

the container you pour the gasoline from is

clean and free from dust or other foreign

particles° Never use gasoline that may be

stale from long periods of storage in the

container.

L_ CAUTION: Never fillthe gas tank

while the engine is runningor hot

Immediately wipe off any spilledgasoline

before attemptingto start the engine,,

/_ CAUTION: Gasoline isflammable

and caution must be used when handlingor

storingit. Do notfill fuel tankwhile Edger/

Trimmer is running, hot,or when inan

enclosed area, Keep away from open

flame, electricalspark, and do not smoke

while filling the fuel tank Never fillfuel tank

completely; but fillthe tank to within 1/4-1/2

inchfrom the top to provide space for

expansion of fuel Always fill fuel tank

outdoorsand use a funnel or spout to

prevent spilling. Make sure to wipe up any

spilled fuel before starting the engine Store

gasoline in a clean, approved container,

and keep the cap in place on the container

Keep gasoline in acool, well ventilated

place; never in the house Never buy more

than a 30 day supply of gasoline to assure

volatility_ Gasoline is intended to be used as

a fuel for internal combustion engines

therefore, do not use gasoline for any other

purpose°Since many children like the smell

of gasoline, keep itout of their reach

because the fumes are dangerous to inhale,

as wel! as being explosive°

WARNING: Experience indicates

that alcohol blended fuels called gasohol or

using methanol can attract moisture which

leads to separation and formation Ofacids

duringstorage. Acidic gas can damage the

fuel system of _n engine while instorage

To avoid engine problems;the fuel system

should be emptied before storage of 30

days or longer. Drain fuel tank, start engine

and let _trun untilfuel lines and carburetor

are empty Use fresh fuel next season. See

Storage Instructions for additional informa-

tion. Never use engine or carburetor

cleaner productsin the fuel tank or perma-

nent damage may occur°

TO START THE ENGINE

Before starting the engine, be sure you

have read and understood all the instruc-

tions on the preceding pages The Edger/

Trimmer is equipped with a recoil starter.

The operation of the engine is controlled by

the throttle control lever

• Pull the clutch lever all the way back or

up to the rearmost hole to raise and

disengage the bladeo

• Move the throttle control lever, see figure

on page 7 to the FAST position

• Push primer buttonfive times, see figure

on page 7. Wait about two seconds

between each push

NOTE: Do not use primer button to

restart a warm engine after a short

shutdown

• To start engine, grasp the engine starter

handle firmly with your right hand°

• Hold the edger handle firmly with your

left hand

• Pull up sharply on the recoil starter

handle DO NOT allow the starter rope to

snap back, let it rewind slowly while

holding the starter handle If engine fails

to start after three pulls,push primer

button two times and pull starter rope

again.

• When the engine starts Push throttle

controllever up to increase speed; down

to decrease speed Run at full engine

speed during normal use°

NOTE: The cuttingblade speed is

controlled by the engine speed_To

reduce the cuttingblade speed, push

down on the throttle control lever To

increase the blade speed, push the

throttle control lever up

, To stopthe engine, make sure the clutch

lever isal! the way back or up and move

the+throttle control lever to the STOP

position.

CAUTION: Never run the engine

indoorsor in a poorly ventilated area°

Engine exhaust containscarbon monoxide,

an odorless and deadly gas,,Keep hands,

feet, hairand looseclothing away from any

moving partson the engine or edger/

trimmer. Avotd the muffler and surrounding

areas°Temperatures may exceed 150° F.

EDGING TIPS

• Edging is best p+erformedwhen conditions

are dry. If the soilJstowet, dirt becomes

packed in and around the blade causing

premature belt wear and decreased

performance°

• tfdid does become packed around the

blade, stop the engine, remove the spark

plug wire, and remove the packed debris

before continuingto edge°

• tfvery deep edging isrequired, we

recommend that ashallow cut be made

first,then cuts at greater depth until the

desired depth is obtalned.

• Uniform edging can be performed when

the blade guide rides on and against the

surface whtch you are edging.

• Edging can be customized by varying the

number of passes and by the distance

your blade isfrom the surface you are

edging°

PRODUCT SPECIFICATIONS

Horse Power: 3°8

DisPlacement: 9.52 cu. in. (156 cc)

2_0 qL (unleaded)

Lubrication: 20 oz. SAE_30W

Spark Piug: Champion CJ-8 or

Equivalent

CUSTOMER RESPONSIBILITIES _

RECORDS

Fill In dates as After "_Before'Frs_, "EVOW'Evory Every Begin Bslora

you complete First Each quontiy 5 10 25 kach Storage

regularservice 2 use '=Hours Hours Hours Season

Hours

Lubricate aU Pivot Points

LubricateWheelAxies

CheckEngineoii Levei

ChangeEngine0t1

Replace AirCleanerFilter

ChockSp_.Ptug

Check Drive Belt

Tighten All Screws and Nuts

CheckBladeWeas/Damsge

,I I

v, ,I I

..... _ v" __i

,I I

i !!ii!

GENERAL RECOMMENDATIONS

The warranty on this Edger/Trimmer does

notcover items that have been subjected to

operatorabuse or negligence, To receive

full value from the warranty,the operator

must maintain the Edger/Trimmer as in-

structed inthis manual. The above chart is

providedto assist the operator inpropedy

maintaining the edger/trimmer

Page is loading ...

ling

Blade

TO ADJUST CARBURETOR

The carburetor shown below has been pre-

set at the factoryand readjustmentshould

not be necessary° However, if the carbure-

tor does need to be adjusted, proceed as

follows:

Carburetor

HighSpeed

Screw

only)

• Close the high speed adjusting screw by

hand.

Do not over4ighten,

Then open it 1-1/4 to 1-1/2 turns.

Start the engine and let it warm up.

Set the throttlecontrolto FAST, Adjust

the high speed adjusting screw In until

the engine speed or sound alters. Adjust

the screw out until the engine speed

sound alters, Note the difference between

the two limits and set the screw in the

middle of the range,

ff the engine tends to stall under load or

not accelerate from low speed to high

speed properly, adjust the h_ghspeed

screw out fn 1/8 turn increments untit the

problemis resolved.

Let the engine run undisturbedfor 30

seconds between each setting to allow

the engine to reactto the previous

adjustments.

IMPORTANT: Never tamper the engine

governor, whichisfactory set for proper

engine speed. Overspeeding the engine

above the factory high speed setting can

be dangerous, ifyou think the engine-

governed high speed needs adjusting,

contact your nearest Sears Seryice

Center, which as the proper equipment

and experience to make any necessary

adjustments.

Z_ CAUTION: Neverstoreyouredger!

trimmerindoorsor inanenclosed,poorly

ventilatedareaifgasolineremainsinthe

tankfumesmay reachanopenflame,

sparkor p_Iotlightfrom a furnace,water

heater,clothesdryer,cigarette,etc.

EDGER/TRIMMER

, Clean the Edger/Trimmer thoroughly;

remove all debris and wipe the unit dry_

• Inspect the EdgerfFrirnmer for worn or

damaged parts and tighten alt loose

hardware.

• Oil all pointsdescribed inthe Lubrication

paragraph in the Maintenance section of

this manual.

. Store the EdgerTtrimmer in a protected

area and cover for additional protec-

tion°

IMPORTANT: A yearly checkup or tune-

up by a Sears Service Center is a good

way of ensuringthat your edger/

trimmer will provide maximumpeffor-

mance for the next season.

ENGINE

IMPORTANT: Itis importantto prevent

prevent gum deposits from forming in

essential fuel systemparts suchas.the

carburetor, fuel filter,fuel hose, or tank

during storage. Also, experience indicates

that alcohol-blended fuels called gasohol or

using ethanol or methanol can attract

moisture which leadsto separation and

formation of acids during storage..Acidic

gas can damage the fuel system of an

engine while in storage.

To prevent engine damage (ff edger/

trimmer is not used for more than 30 days)

follow the steps on next page.

• To remove gasoline, runthe engine

until the tank is empty and the engine

stops.

o if you do not want to remove gasoline

a fuel stabilizer (such as Sears

Craftsman fuel stabilizer No. 33500)

may be added to any gasoline_left in

the tank to minimize gum deposits

and acids+ if the tank isalmost empty,

mix stabilizer with fresh gasoline in a

separate container and add some tothe

tank. Always follow instructions on

stabilizer container. Then run engine at

least 10 minutes after stabilizer isadded

to allow mixture to reach carburetor.

Store Edger/Trimmer in a safe place. See

IMPORTANT under STORAGE (EN-

GINE).

Store the EdgerTrimmer in the wheels-

down, operating position,+Ifthe Edged

Trimmer is storedin anyother position, oi!

fromthe crankcase could enter the

cylinder, causing a service problem,,

You can keep your engine ingood operating

condition duringstorage by:

• Changing oil.

• Lubricating the piston/cylinder area

This can be done by first removing the

spark plug and squirting dean engine

oil intothe spark plug hole, Then cover

the spark plug hole with a rag to absorb

oil spray, Next, rotate the engine by

pulling the starter two or three times,

Finally, reinstallspark plug and attach

spark plug wire.

TROUBLE CAUSE CORRECTION

Difficult sterling Stale fuel Drain fuel tank, Fill with fresh

fuel

or Defectivespark plug Clean and re-gap spark plug

Clogged fuel line Replace fuel filter

Engine runs

erratic Blockedfuel line or empty fuel tank Clean fue! line; check gas tank

Carburetor outof adjustment Have carburetor adjusted

Fouled spark plug Clean and adjust gap

Croggedair Cleaner Tap clean or replace air cleaner

Jammed due to foreign object Clear obstruction

Cutting blade .......................

falls to turn Looseblade Tighten blade retainingnut

Defective belt Replace V-belt

Defective quill bearings i Replace the bearings

• =

Blade falls to cut Damaged or worn blade Reverse blade +orreplace brade

properly

., Stop engine immediately; tighten

vibration alt bolts,_If vibrationcontinues,

take the unitintothe nearest

Sears Service Center

CRAFTSMAN9"-3,8H.P.EDGER/TRIMMER536.797470

ENGINEASSEMBLY

Note: Always use original equipment

parts. Useofs_n/lcelreplacement

_adsotherthan originalpads may void

,our warranty

REF°

NO.

, ,,,,,,

PARTNO.

ENGINE

48148

314781

181608

120638

45602

32668

313011

51600

3.8 HP 143 963507

(See Engine pages)

Screw, 3/8-16 x 1.00

Pulley, Half V3L

Screw, 5116-24x 1O0 HHC

Washer, SPTLK

,328x 60x,09

Washer, Flat 333x 87x 11_

Belt, V 4L 32.60LG

Screw and Washer Assy

Guide, Belt

side

REF

NO. PART NO.

40 331281-833

41 181624

42 315095

43 173030

44! 308237

451 315095

80 323534-833

81 308154-833

339690

Al$unnumbered items ere

Interchangeable with opposite

PART NAME

Cover, Engine F

Screw, 5/16-24> HHC

Spacer, Sleeve

.335x 431 x2.50

Screw, 5/16-24>

Spacer, 3221D .562 OD

Spacer, Sleeve

.335x 431x250

Frame, Assy Ec |

Strap

]Owner*s Manua

323095D

CRAFTSMAN 9" - 3°8 HoP.EDGER/TRIMMER 536.797470

BLADEGUARDASSEMBLY _)

REF

NO, PART NO.

1 33io76,5

2 57072

3 120393

4 1498

5 326748-83.3

I IREF:I

PART NAME NI.N_ PART NO,

Blade Guard J 6 _

Can', Bolt5tt6-18x,63 I 8 J 53405-833

Flatwasher,344x,69x065 I 9 I 411666

Nut, 5116-18 Reghexctrlk

10 I 1501

Guide, Belt Front

332247O

PART NAME

Screw, 114-20x,50 Tap

Cover, Quill Pulley

Screw, 10-24x 50 Tap

Flat'washer 203x 56x 040

FRONT WHEEL BRACKET ASSEMBLY

REF,

NO. PART NO.

150 339299-833

151 331422

152 338614

153 325892

154 331421

t55 332002

156 331419

157 20252

158 22265

159 45905

160 5133-3

161 331394-833

162 120393

163 339388

164 1495

PART NAME

A I Front .....

Rod, Front Mount Curb Hopper

Pushnuto Washer

Washer, Plastic

Spacer, Height Adjust

Pin, Spring. 187Diaxt 50Lg

Lever, Height Adjust

Knob, Rectangle

Flatwasher .515xl. 38x.119PL

Nut, 3/8-16 Hwdfltk Mack

Screw, 5116-18x.63

Plate, Hetght Adjust Quad

Flatwasher, .344x,69x 065

Knob, W/5!16-18 Stud

Nut, 5/16-t8 Reghexctdk

3317650

CRAFTSMAN 9" - 3.8 H,P, EDGER/TRIMMER 536,797470

CURB HOPPERASSEMBLY

REF.

NO. PART NO,

i170 6842

171 180077

172 t498

180 126380

181 8O82

182 45222

183 120393

184 !3527

185 120376

186 310896

PART NAME

Bracket, Curb Hop Mnt

Screw, 5116.18x 75

Nut, 5/16-18 Reghexctdk

Carr. Bolt, 5/16-18x200

Clev;s

Spacer, Slav 356x.63xl o01

Flatwasher _344x69x 065

Knob, T

Nut, 5116-t8 Reghex

Rod, Wheel Support

32317gD

BLADE ASSEMBLY

REF.

NO.

30O

!3Ol

302

305

310

3il

312

32O

PART NO.

120396

338656-833

308254

1499

308243

411666

1501

51603

PARTNAME

Flatwasher,_531xtO6x_095

QuillSupptAssy

ShoulderBolt3!8-16

Nut,3f8-16 Reghexctdk

Deflector.Rubber

Screw,10-16x.50Tap

Flatwasher,,203x,56x040

QompressionSpring

323129C

REF=

NO. PART NO. PART NAME

,, _,,,_,,,,_,,,.,,,,,,,,_,, _,

32t 338070 Quill Assembly, LrgSuppl

322 308466 Index Lever

323 308155 Torsion Spdng

325 1498 Nut, 5116-18 Reghexctrlk

329 22265 Flatwasher; 515xl 38x 1t9

330 334056-853 Blade Edger

33't 46023 Nut, l!=20Wdfl

CRAFTSMAN 9" +3,8 H+P.EDGER/TRIMMER 536.797470

HANDLE ASSEMBLY

iREF.

INO, _PART NO.

720

721

722

726

728

750.

754

332232-853

1498

51333

180083

1498

580292-853

36368

PART NAME

Lower-i_a;_die

Nut, 5/16+18 Reghexctrtk

Screw. 5116-18x,,63

Screw, 5116-18xt, 50

Nut, 5/16-18 Reghe_ctrtk

ControlRod

Hair Pin, _072Diaxl. 13Lg

330225D

UPPER HANDLE ASSEMBLY

REF.

NO. PART NO,

725 332239

731 310052+85_

732 180024

735 1502

737 310050-85_

738 180081

739 25644

740 1498

741 56924

743 310053

745 1499

PART NAME

Upper Handle & Foam

Plate Selecter

Screw, 1t4+29xl ,25

Nut, 114-20 Reghexctdk

Handle, Depth Adjust

Screw, 5116-18xl 25

Spdng

Nut, 5116+18 Reghexctdk

Grip, Hand

Stud

Nut. 3/8-16 Reghexctdk

323136[3

0 0

CRAFTSMAN 9" - 3.8 H.P. EDGER 536°797470

TIRESASSEMBLY

REF.

NO.

PART NO.

336545

180113

t 20393

51887

55273

310716

310715

41529

2968

121222

PART NAME

_re & RimSXl,,75

Screw, 5/16-18x3.00

Flatwasher, 344x.69x.065

Spacer, Slev 328xA95x139

Nut, 5116-18 Wdfllk

Shoulder Bolt, 3/6-16

Spacer. Slev 390x,70x 70

Nut, 3/6-16 Hxctrlkjam

Flatwasher oS04x]Sx.059

Cotter Pin

332250B

DECALS

NO. PART NO.I

820 338984 I

82_ ' 69711

822

823 338982

824 333873

825 312548

826 333874

PART NAME

Decal. Recoil Cover

Decal, Information Danger

Reference Only

Deca!. 38 Sears Edger

Decal, Angle indicator

Decal, Quadrant Selector

Decal, Blade Cover

323t37D

CRAFTSMAH ,_.CYCLE ENGINE MODEL HUMBER: 143.963507

215

CRAFTSMAN 4-CYCLE ENGINE MODEL NUMBER: 143.963507

FIEF.

_10.

._0

._5A

._6A

_,2

€9

100

102

103

t10

119

120

t25

125

126

!26

130

130A

PART NO.

36560

26727

28277

31334

31336

31335

650548

34593

32600

36552

35883

650802

650926

359O2

34514

34515

34516

325388

325488

32549B

28986

28987

28988

20381

309638

32610A

!27241

128594

33149A

29745

650128

27677A

35863A

27642

26208

30574A

30590A

30591

30588A

650488

610961

611195

650815

650816

34443A

650872

651007

35182

36437

36438

36471

36472

293148

293t5C

650694

6021A

PART NAME

Cy_Inder

_ncL 2, 20, 72, & 125}

uowel

Washer

GovernorRod

GovernorLever

GovernorLever Clamp

Screw, 8-32 x 5116"

ExtensionSpring

Oil Seal

BlowerHslng Baifle

nd. 262)

alfle Extension

Screw, 1t4-20 x 5/8"

Screw, 8-32 x 21t64"

Crankshaft

Piston,Pin& RingSet

(_,010OS) '

ston,Pin & Ring Set

(].020OS)

start& RingAssy

(Sld) (lnc143)

Piston & PinAssy

010" OS) Incl 43

tston& Pin Assy

(.020" OS (Inc143)

Ring Sat (Std)

Ring Set (010" OS)

Ring Set ( 020" OS)

PistonPin RetainRing

ConnectingRod Assy

ncl46 & 49)

onnecttngRod Bolt

Valve Ltlter

Oil Dipper

Camshaft(BCR)

Blower HousingExt

Screw, 10..24x 1/2"

CylinderCoverGasket

CylinderCover({nci 75

thru 83, 311)

Oil Drain Plug

Oit Seal

Governor Shaft

Washer

Governor Gear Assy

(tnc181)

Governor Spool

Screw 114_20x 1-1t4"

FlywheelKey

Flywheel

Believi]leWasher

Flywheel Nut

SolidState Ignition

SolidState Mting Stud

Screw, Torx T-15, 10-24

x 15116"

Ground Wire

CylinderHead Gasket

CylinderHead (Incl 130)

Exhaust Vatve(Std)

ncL151)

xhaustValve (1132" OS)

Inc1151)

ntake Valve (Std)

(Inci 151)

tntakeValve (1/32" OS)

(Inc1151)

Screw 5/16-18 x 2"

Screw 5tt6-18 x 1-1/2"

FIEF_

_0=

_32

_35

W50

_69

170

f7!

172

173

174

178

179

t82

t84

t85

185

.>00

Z03

Z04

206

_.09

Z09A

215

?.24

238

Z39

241

245

250

260

262

275

277

285

287

290

292

298

B00

301

311

313

339

340

342

345

370A

3708

370K

380

390

400

416

417

PART NO.

650708

33636

31672

31673

27234A

27666

31410

34146

35350

30200

29752

30593

620t

26758

36703

31341

35677

31342

650549

610973

650139

30322

32410

650451

26754A

650932

34338

35797

35066

35065

35585

650737

35493

650988

36467A

650926

29774

26460

65O665

35591

35335

27625

34080

28212

35828

650751

32664

36261

35703

36695

632589

590732

36439

36085

650760

PART NAME

Washer

Resistor Spark Plug

(CJ8)

Valve Spring

Valve SpdngCap

Valve Cover Gasket

BreatherBody

BreatherE]ement

Valve Cover

BreatherTube

S_ew 10-24 x9t16"

Nut& LockWasher

t/4-28

RetainerClip

Screw 1/4-28 x7/8"

Carburetorto Intake

PipeGasket

intakePipe

Inc1182, 184,224)

Governor Link

ControlBreaker(lncl.

203 thru209A) •

CompresstonSpdng

Screw5,40 x 7/16"

Terminal

Screw8-32 xt/2"

Locknuf,8-32

Centre{Knob

Screw 1/4-20 x 1"

Intake PipeGasket

Screw 10-32 x 49164"

AirClef,net Gasket

Air Cleaner Collar

AirCleaner F{iter

AirCleaner Cover

Blower Housing

Screw 1/4-20 x 1/2"

Mullter (Ind 277)

Screw 1/4-20 x 2-5116"

Starter Cup

Screw 8-32 x21/64"

Fuel Line

FuelLine Clamp

Screw 1/4-15 x 7/8"

Fuel Tank

(lnc1292 & 30t)

Fuel Cap

Oil FillPlug

Spacer

FuelTank Bracket

Screw 1t4-20 x7t16"

Baffle Heat

LubricationDecal

ControlDecal

Starter Decal

Carburetor(Ind 184)

RewindStarter

Gasket Set

Spark ArrestorKit(incl

417}(opt)

Screw, 8-32x3/8" (opt)

This engine could havebeen buii!with590738

starter.Referto the designo! the rope pulley

strengthdbsfor partidentification.|ndividual start_

_artsdo not interchange,

Page is loading ...

Weed Eater 180083 Owner's manual

Brand: Weed Eater

Model: 180083

Category: Grass trimmers

Type: Owner's manual

Download PDF

report

in other languages

español: Weed Eater 180083 El manual del propietario

Weed Eater 180083 Owner's manual

Weed Eater 180083 Owner's manual

in other languages

Other documents