Bresser 70-09000 WoW200 Owner's manual

Page is loading ...

18



This device contains electronic components that are powered by

either a mains connection or batteries. Never leave a child unsu-

pervised with this device. The device should only be used as per these

instructions otherwise there is a serious RISK of ELECTRICAL SHOCK.

Children should only use this device under supervision. Keep packaging

materials (plastic bags, rubber bands, etc.) away from children. There is

a risk of SUFFOCATION.

Batteries should be kept out of children’s reach. When inserting batte-

ries please ensure the polarity is correct. Leaking or damaged batteries

can cause injury if they come into contact with the skin. If you need to

handle such batteries please wear suitable safety gloves.



Do not expose the device to high temperatures. Use only the

mains adapter supplied or those battery types recommended. Ne-

ver short circuit the device or batteries or throw into a re. Exposure to

high temperatures or misuse of the device can lead to short circuits, re

or even explosion!



Never take the device apart. Please consult your dealer if there are

any defects. The dealer will contact our service centre and send

the device in for repair if needed.

Only use the batteries that have been recommended. Always replace

low or used batteries with a completely new set of full capacity batteries.

Do not combine batteries of different brand, type or capacity. Batteries

should be removed from the device after long periods of disuse.

GB/IE

19



Remove the device from it’s energy source before cleaning (remo-

ve plug from socket / remove batteries).

Clean the exterior of device with a dry cloth. Do not use cleaning uids

so as to avoid causing damage to electronic components.



Dispose of the packaging material/s as legally required.

Consult the local authority on the matter if necessary.

Do not dispose of electrical equipment in your ordinary refuse.

The European guideline 2002/96/EU on Electronic and Electri-

cal Equipment Waste and relevant laws applying to it require such used

equipment to be separately collected and recycled in an environment-

friendly manner.

Empty batteries and accumulators must be disposed of separately. Infor-

mation on disposing of all such equipment made after 01 June 2006 can

be obtained from your local authority.

20



Thank you for your purchase of the WoW200 Weather station.

The basic package comes with a main unit, which is the weather fore-

cast station, a remote unit that is the thermo-hygrometer and the AC/

DC adaptor.

The main unit is capable of keeping track of maximum and minimum

temperature of different sites. And no wire installation is required and

operates at 433 MHz.

The packaging consists of:

- Main Unit

- Outdoor Thermo-hygrometer sensor

- AC-adaptor

- Instruction Manual

GB/IE

21



NOTE:  ON FRONT SIDE

Flashes when the remote unit transmits a reading.

 

Accommodates 2 UM-3 or “AA” size 1.5V batteries

 

Resetting of all functions after changing the channels

 

Toggles the unit of temperature (if applicable)

 

Channel is to be selected before batteries are installed

 

For mounting the sensor on the wall

Page is loading ...

GB/IE

23

 

Activates the snooze function and Backlight (at battery operation)

 

Display the alarm time or sets the alarm status for alarm 1

 

Display the alarm time or sets the alarm status for alarm 2

 



Decrease the Value of a setting

 





Increase the Value of a setting; Force to receive

Radio-controlled Clock signal

 

Force to search for remote sensor signal

 

Receive the maximum or minimum temperature

and humidity of main unit and remote unit

 

Toggle among different channels of the remote

sensor units. Key sequence: Indoor > Channel 1

> Channel 2 > Channel 3 > Indoor… Also, you can

press and hold to enter the Auto Scroll function

 

Toggles the display modes and conrms entry

while setting the values for display

 

Press to reset all values to their default setting

24





For best operation,

1. Insert batteries for remote units before doing so for the main unit.

2. Position the remote unit and main unit within effective transmission

range, which, in usual circumstances, is 20 to 30 meters. Note that

the effective range is vastly affected by the building materials and

where the main and remote units are positioned. Try various set-ups

for best result. Though the remote units are weather proof, they

should be placed away from direct sunlight, rain or snow.



1. Remove the screws on the battery compartment.

2. Select the channel

3. Install 2 batteries (UM-3 or “AA” size 1.5V) strictly according to the

polarities shown or remove the insulating strip.

4. Operating the remote unit with the supplied power supply activates

the display's background illumination.



Install 2 batteries (UM-3 or AA size 1.5V) strictly into the main unit and

plug the AC-adaptor to give power to the main unit as well, you will see

the display is lighted up.



When it is time to replace batteries for the remote sensor, the respective

low battery indicator will show up on display. In addition, the low bat-

tery indicator will show up on the Main Unit display for this specied

Remote Sensor Unit.



When the battery power is not enough, there is a battery icon will

be shown on the display, so we need to use the new batteries. If the AC-

adaptor cannot connect to the Main Unit properly, or the AC-adaptor is

GB/IE

25

removed out of the Main Unit, the icon will be shown on display.



The receiving unit is equipped with a base which allows you to mount it

on an even surface.



1. Before mounting the device on a wall, make sure that the location of-

fers the receiving unit optimal reception from the external sensor.

2. Mount a screw in the desired location. Ensure that the screw can

hold the weight of the receiving unit. Leave a space of about 5 mm

between the head of the screw and the wall. Hang the receiving unit

on the screw. Make sure that the receiving unit is securely fastened

onto the head of the screw before you let it go.



a. Once batteries are in place for the remote unit, they will start transmit-

ting temperature and humidity readings at around 45 seconds inter-

vals. The main unit will also start searching for signals for about two

minutes once batteries are installed. 10 seconds upon successful

reception, the outdoors temperatures and humidity will be displayed.

The main unit will automatically update its readings at about 45-sec-

ond intervals.

b. If no signals are received, blanks “ ” will be displayed.

Hold  for 2 seconds to enforce another search for

about 2 minutes. This is useful in synchronizing the transmission and

reception of the remote and main units.

c. When remote signal reception is nished, it will automatically synchro-

nize its current time and dated when brought within rang of the “DCF”

RF signal. Repeat this step whenever you nd discrepancies between

the reading shown on the main unit and that on the remote unit.



The maximum and minimum recorded indoor / outdoor temperature

26



 rising steady falling

and humidity will be automatically stored in memory. To display these

readings, press  button to display the minimum reading and press

 button to display the maximum reading, and then press 

button to resume to the current reading.



The Main Unit is able to detect atmospheric pressure changes. Based

on the collected data, it can predict the weather for the forthcoming

12 to 24 hours.

Remark:

1. The accuracy of a general pressure-based weather forecast is at

about 70%.

2. The weather forecast may not necessarily reect the current situation

3. The Sunny icon, as applies to night time, implies clear weather there

is a trend indicator on the display to show the measured atmospheric

pressure are rising , steady , or Falling .



The comfort level indicators COM, WET or DRY will tell you if the current

environment is comfortable, too wet, or too dry. The comfort indicators

will appear on the display of the Main Unit when the following conditions

are satised:





 Sunny

Partly

Cloudy

Cloudy Rainy Snowy

GB/IE

27



If without obvious reasons the display of the outdoor

temperature goes blank, hold [SEARCH] button for 2

seconds to enforce an immediate search. If that fails, check:

1. The Remote Sensor Unit is still in place

2. The batteries of both the Remote unit and the Main Unit. (Notes: when

the temperature falls below freezing point, the batteries of outdoor

units will freeze, lowering their voltage supply and the effective range.

3. The transmission is within range and path is clear of obstacles and

interference. Shorten the distance when necessary.



Signals from other household devices, such as door bells, home security

systems and entry controls, may interfere with those of this product and

cause temporarily reception failure. This is normal and does not affect

the general performance of the product. The transmission and reception

of temperature readings will resume once the interference recedes.



1. After the batteries are installed. The clock will automatically search





















COM 20°C to 25°C

40% RH to

70% RH

Comfortable

WET -5°C to +50°C OVER 70% RH

Too wet

(moisture)

DRY -5°C to +50°C Below 40% RH Too Dry

No

Indicator

Less than 20°C

or More than 25°C

40% RH to

70% RH

No comment

28

the radio signal. It takes about 3-5 minutes to nish this process.

2. If user wishs to disable the auto-reception feature, hold the [ + ] button

for 2 seconds to disable it.

3. To enable the auto-reception feature again, holds the [ + ] for 2 sec-

onds again to force it receive and allow it receive at desired time.

4. If the radio signal is received, the date & time will be set automatically

with radio control signal icon [ ] turns on.

5. If the clock fails to receive the time signal, it will be show as [ ] icon.

Then user can set the time manually.



To set the clock manually, hold  for two seconds it will show the

display language. Use [ + ] or [ – ] to change it. Press  to con-

rm. Repeat the same procedure to set year, month, date, 12/24 hour

format, hour and minute. During the setting, use [ + ] or [ – ] will increase

or decrease the value rapidly. For display language, you are able to se-

lect English (En), German (DE), French (Fr), Italian (IT), Spanish (SP)

and Dutch (DU). If there is an item you do not need to change, simply

press to bypass the item. When you nished the change, press

 to exit. The display will return to the clock mode.



In the normal display mode, you can use the  key to select from

the following display modes:

- Time display with seconds

- Time display with days of the week

- A second time zone with the days of the week

- A second time zone with seconds



1. To set the zone time,

2. Press  until at zone time display mode which there is a ‘ZONE’

icon on LCD display,

GB/IE

29

3. Hold  for two seconds, the zone time offset will be dis-

played.

4. Enter the offset using [ + ] or [ – ].

5. Pressto exit.



There are total two alarms, namely alarm 1 and alarm 2 which can be

operated by press [AL. 1] an [AL. 2] respectively. The alarm setting pro-

cedure is listed as below.



1. Press 

2. Press [ + ] or [ – ] to turn on / off the alarm function.

3. Press and Hold [AL. 1] button until the hour for alarm is ashing

4. Set the hour by press [ + ] or [ – ], and then press [AL. 1] button to

conrm.

5. Then, to set the minute by press [ + ] or [ – ], and then press 

button to conrm.

6. If you would like to leave the alarm display and show calendar,

press  to show calendar. If you would like to switch to alarm

1 display, press  button.



1. Press 

2. Press [ + ] or [ – ] to turn on / off the alarm function.

3. Press and Hold  button until the hour for alarm is ashing

4. Set the hour by press [ + ] or [ – ], and then press  button to

conrm.

5. Then, to set the minute by press [ + ] or [ – ], and then press 

button to conrm.

6. If you would like to leave the alarm display and show calendar, press

 to show calendar. If you would like to switch to alarm 1 dis-

play, press  button.

30



When the alarm is wake up, you are able to press  to off the

alarm



Main Unit

Proposed operation range

-5°C to 50°C

Humidity measuring range

25% to 90% at 25%

Temperature resolution

0.1°C

Humidity Resolution

1%

Battery

1.5V AA x 2pcs

Remote Sensor Unit

Proposed operation range

-10°C to 50°C

Humidity measuring range

25% to 90% at 25%

Temperature resolution

0.1°C

Humidity Resolution

1%

RF Transmission frequency

433 MHz

Maximum No. of remote unit

3

Sensing cycle

around 43 to 47 seconds

Battery

1.5V AA x 2pcs



This product is engineered to give you years of satisfactory service if you

handle it carefully. Here are a few precautions:

Do not tamper with the unit's internal components. Doing so will invali-

date the warranty on the unit and may cause unnecessary damage. The

unit contains no user-serviceable parts.

Only use fresh batteries as specied in the user's manual. Do not mix

new and old batteries as the old ones may leak.

GB/IE

31



Product Type: Weather Station

Product Name: WoW200

Article No.: 70-09000

Meade Instruments Europe GmbH & Co. KG declares that the above-

named product corresponds to the following directives and relevant

standards in its conception and design as well in the version marketed

by us.

 

99/5/EC (R&TTE)

EN 300 220-2 V2.1.2:2007

EN 300 330-2 V1.3.1:2006

EN 301 489-3 V1.4.1:2002

ETSI EN 301 489-1 V1.6.1:2005

EN 50371 : 2002

EN 60950-1:2006+A11+A1

This declaration is no longer valid in the event of a change to the product

which has not been coordinated with us.

Meade Instruments Europe GmbH & Co. KG

Gutenbergstr. 2

D-46414 Rhede

Germany

Phone: +49 (0) 2872 8074-0

Fax: +49 (0) 2872 8074-444

e-Mail: info@bresser.de

Rhede, 2010-12-08 Helmut Ebbert

Managing Director

Page is loading ...

49



TESTIMONE LUMINOSO (LED)

Lampeggia brevemente durante la trasmissione delle date misurate.

 

 

  

Questa funzione non è disponibile per tutti gli apparecchi

 

Installazione del sensore su uno dei canali (1, 2 o 3)

 

ENCOCHE PER LA FISSAZIONE MURALE

IT

Page is loading ...

ANL7009000MSP0111BRESSER

Meade Instruments Europe

GmbH & Co. KG

DE-46414 Rhede/Westf.

Germany

www.bresser.de

Irrtümer und technische Änderungen vorbehalten. · Errors and technical changes reserved.

Sous réserve d’erreurs et de modiﬁcations techniques. · Con riserva di errori e modiﬁche tecniche.

Queda reservada la posibilidad de incluir modiﬁcaciones o de que el texto contenga errores.

Bresser 70-09000 WoW200 Owner's manual

This manual is also suitable for

Bresser 70-09000 WoW200 Owner's manual

in other languages

Related papers

Other documents