Neewer Q-CTTL Wireless Flash Trigger User guide

Q-CTTL Wireless Flash Trigger
Brand
Neewer
Model
Q-CTTL Wireless Flash Trigger
Type
User guide

This manual is also suitable for

Q-CTTLWirelessTrigger
FCC Warning:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer
could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure requirement. The device can be used
in portable exposure condition without restriction.
TableofContents
AboutThisManual
ThankyouforpurchasingtheNEEWER®Q-CTTLWirelessTrigger.
Themanualwillcoverthefollowing：
thebasicoperationproceduresandfunctionsoftheWirelessTrigger.
theapplicationenvironmentandsafetyuseoftheWirelessTrigger.
theinstallationoftheaccessoriesoftheWirelessTrigger.
1.PackageContents
2.CompatibleDevice
3.Nomenclature
4.PowerSupplyMode
5.Mode
6.Set-upProcedures
7.SafetyNotes
8.Caution
9.Maintenance
10.ProductParameters
11.WarrantyPolicy
12.TrademarkandStatement
13.ContactUs
1
2
3
6
7
13
14
15
15
16
17
18
18
1 2
NE EWER
SyncCable
ScrewAdapter
Camera On-cameraFlash
HotShoeStand
1.PackageContents Accessories
Manual
Uponreceivingthepackage,pleasecheckwhetheralltheproductsareincluded.
Ifthereareanymissingorbrokenproducts,pleasecontactNeewerCustomerService
(support@neewer.com).
2.CompatibleDevice
3.Nomenclature
YoucanpresstheFunction2andFunction3buttontogetherforthree
secondstorestorethetriggertodefaultsettings.
Type-c
FirmwareUpdate
2.5mmSyncPort
TriggerHotshoe
Battery
Compartment
Lock/
ReleaseButton
AF-assist
illuminator
SettingDial
3 4
FlashHotshoe
AF-assistSwitch
PowerSwitch
Menu
Zoomin/TX/RX
Mode/ScreenLock
TestFlash
Group
Function1
Function1
Function1
Function1
T
SE T
STBY-T
STBY-R
BEEP
2.0
Display
MultipleGroupDisplay MenuDisplay
T
Group
Mode Power ModellingLampGroup
Channel
HighSpeedSync
BatteryPower
ModellingLamp
MasterSwitch
Zoom/Channel
Buzzer
5 6
T
Zoo m
AUTO
TTL
SingleGroupDisplay
4.PowerSupplyMode
byAABattery
GroupDisplay
Whenonmultiplegroupdisplay,thetriggerwill
switchtosinglegroupdisplaywhenyouquick
pressthe“”button.Itwillswitchbacktothe
multiplegroupdisplayifyoupressthebuttonagain.
5.Mode
ModeSwitch
Chooseonegroup(demo:GroupA)andpressthe“”
buttontoswitchmodeinthefollowingorder:
TTL→M→OFF.
Inthismode,thetriggercanadjusttheflash
outputbetween-3and+3in1/3stopincrements.
Atthelevelof0,therewillbenoexposurecompensation.
ChooseaspecificgroupandrotatetheSettingDialto
changethecompensationlevel:-3.0、-2.7....0.0.....+3.0、+2.7....
ExposureCompensationSetting
7 8
T
T
T
Zo om
AU TO
T
Zo om
AU TO
TTL AsTransmitterorReceiver
Thetriggerwillworkastransmitterwhenyoupress
the“”buttonforthreesecondsuntilthesymbol
“T”appearsonthedisplay.Itwillturnintoareceiver
ifyoupressthebuttonagainfor3secondsuntilthe
“R”lettershowsonthedisplay.
RestoreDefaultSetting/HighSpeedSync
Thetriggerwillrestoretodefaultsettingswhenthe
Function2andFunction3buttonarepressedtogether
forthreeseconds.ToactivatetheHSSfunction,please
adjusttomainmenupageandpresstheFunction2
buttonuntilthe“ ”symbolappearsonthedisplay.
T
ModellingLampControl
Whennospecificgroupischosen,thetriggercanturn
on/offallmodellinglampswhenyouquickpressthe
“Function4”button.Whencontrollingaspecificgroup
oflights,pleasequickpressthe“ Function4”buttonto
changetheirlightintensityfromLevel1toLevel6.(The
modellinglampswithinthegroupcanallbeturnedoff
bypressingtheFunction4buttonfor3seconds.)
ThelightintensitylevelonlyfitsthatofQ5TTLstrobelight.
ZoomSetting
Quickpressthe“ Function1”button.Thenchoosea
specificgroupandrotatetheSettingDialtochange
zoomsettings:auto/20-200mm.ToexittheZoom
Settingpage,pleasequickpressthe“ Function1”
buttonagain.
Thetriggerfeatures32channels,availableforswitchfromChannel01toChannel32.
Pleasemakesurethatthetransmittingandreceivingdevicesareonthesamechannel.
Channel/TestFlash
Pressthe“ Function1”buttonfor3seconds.Thenyou
canrotatetheSettingDialtochooseasuitablechannel.
Thetriggercanmakeaflashlightfiretestflashwhenyou
pressthe“ ”button.
T
9 10
T
T
Zo om 20
Zo om AU TO
Zo om AU TO
Zo om AU TO
Zo om AU TO
CustomSettings
StandbyMode
ThetriggerdisplaywillturnoffIfnooperations
areperformedfor90seconds.Toactivatethe
display,pressanybuttononthetrigger.
Ifmountedonthehotshoeofacamera,thetriggercanbeactivated
bypressingthecamera'sshutterreleasebuttonhalfway.
11 12
ScreenLock
Pressthe“ ”buttonfor3secondsuntiltheword
“LOCKED”appearsonthedisplay,whichsuggeststhat
allbuttonshavebeendeactivated(exceptforthetest
flashbutton“ ”). Tounlockit,pleasepressthe
“”buttonfor3secondsuntiltheword“ LOCKED”
disappearsonthedisplay.
T
LOC KED
T
CustomSymbol
SRBY−T
SRBY−R
BEEP
LIGHT
SYNC
LCD
ID
Function
StandbyTimer
Buzzer
BacklightTimer
SyncPort
LCDContrast
WIFIID
Option
ON
OFF
30min
1H
2H
ON
OFF
12sec
OFF
ON
IN
OUT
-3-+3
OFF
01-29
Description
willturnoffwhennooperationsareperformedfor30minutes.
willturnoffwhennooperationsareperformedfor1hour.
willturnoffwhennooperationsareperformedfor2hour.
On
On
Off
Off
willturnoffwhennooperationsareperformedfor12seconds.
Alwaysoff
Alwayson
fireQ3flash
between-3and3
Off
availablefrom01to99
triggersignalinput
StandbyTimer
7.SafetyNotes
Pleaseavoidusingtheproduct
whereitwillbeexposedtohigher
temperaturesthan50degrees
Celsius.
＞50℃
6.Set-upProcedures
Pleaseheedthepositiveornegativepolaritywheninsertingthebatteries.
Iftheyarewronglyplaced,thetriggerwouldn'tturnon.
InsertAAbatteriesinthebattery
compartmentandlatchthecover.
Attachthetriggerhotshoetoyour
camera'scoldshoe.Then,turnthe
knobinthepictureaboveclockwise
untilitistightened.
13 14
Pleasedonotusethelightinthe
rainorinahumidenvironment.
10.ProductParameters8.Caution
Model
SignalTransmissionDistance
Built-inWIFI
Modulation
Channel
WIFIID
Group
2.5mmSyncPort
TX/RX
FirmwareUpdate
PowerSupply
Dimension
NetWeight
Q-C
0-100m
2.4GHz
MSK
32
01-99
5
Areceiverdevicecancontrolcamerashootingwitha2.5mmsynccable.
master/slavemodeswitch
viatheType-CUSBinterfaceonthetrigger
AAbattery
about120grams
105*75*64MM
Pleasedon'tdisassembleormodifytheproductunlessprofessionallycertified.
Otherwisetheremightberiskofmalfunction.
Pleasekeeptheproductdryandavoidtouchingitwithwethands.
Pleasedon'tusethetriggernearflammableorexplosiveitems.
Pleaseavoiddisposingofbatteryinafireorkeepingitnearfiresource.
Shouldtherebemalfunctionofthetrigger,pleaseturnitoffimmediatelyandtryto
identifythepossiblecause.
Pleaseavoidusingnewandoldbatteriestogetherordifferenttypesofbattery.
Pleasedon'tshortcircuitordismantlebatteries
9.Maintenance
Softclothisrecommendedtocleanthetriggerscreen.
Pleaseremovethebatterieswhenthetriggerisleftunusedforalongperiodoftime.
Thetriggershouldbekeptinadryandwell-ventilatedenvironment.
Pleaseavoidusingthetriggerincloseproximitytomagneticdevicesandstrong
electrostaticfield,suchasradiotransmitter,otherwisethetriggermightmalfunction.
15 16
17 18
11.WarrantyPolicy
Reminder:Pleasekeepthepackageboxforatleast15daysbecauseitisnecessary
tousethepackageboxtoprotecttheproductduringtransportation.
WarrantyPeriod
YoucanregisteryourNEEWER®productforitsfree1-yearwarrantyat
www.neewer.com.Thanks！
Yourquestionsorsuggestionarehighlyvaluedandappreciated.Please
feelfreetocontactus,andwewilldoourbesttofullysatisfyyou.
E-MAIL:support@neewer.com
WarrantyRestrictions
ThefollowingconditionsareNOTcoveredbytheNEEWER®Warranty:
(1)Theproducthasexpiredtheone-yearwarrantyperiod;
(2)Theproductismalfunctionedordamagedbecausetheuserdidnotfollowthe
WirelessTriggertouse,adjust,oroperatetheproduct;
(3)Theproductismalfunctionedordamagedduetorain,hailstorm,fumigation,
medicine,chemicalsornaturalwastage;andduetoforcemajeure(includebutnot
limitedtoearthquake,Typhoon,fire,flood,violentcrime);
(4)Theusermodify,dismantle,repairtheproductanditspartswithoutpermission;
(5)TheuserdamagedthepartsofWirelessTriggerbyusingnon-originalaccessories,or
changedthecircuit,lineconfigurationwithoutpermission;
(6)Theproductismalfunctionedordamagedbycollisionorfall-offduetotheuser;
12.TrademarkandStatement
13.ContactUs
NEEWER®isaregisteredtrademarkofNEEWER®TechnologyCompany,Ltd,
whichisprotectedbylaw. NEEWER®companyreservesallrightsforthistrademark.
NEEWER®hascontinuouslydevoteditselftodevelopingandimprovingphotography
andmusicproducts.Weholditourmissiontopursueexcellenceandimprovecustomer
experience.
Theactualproductmaydifferfromthepictureinthismanualincolorand
appearance.
Yourquestionsorsuggestionarehighlyvaluedandappreciated.Pleasefeel
freetocontactus,andwewilldoourbesttooffersatisfyingservicesforyou.
E-MAIL:support@neewer.comWEB:www.neewer.com
(7)WarrantyCard,After-saleServiceCard,invoiceoritemNodoesnotconformtothe
product;
(8)Anuserchangesthewarrantyservicedateoftheproductanditspartswithout
permission;
(9)Thepanelandmainpartsarebeyondmaintenancerange;Thesecuritylabelonthe
productismissingordamaged;
(10)TheWirelessTriggerisusedasacommercialproduct;
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

Neewer Q-CTTL Wireless Flash Trigger User guide

Q-CTTL Wireless Flash Trigger
Brand
Neewer
Model
Q-CTTL Wireless Flash Trigger
Type
User guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents