2. Computers & electronics
  3. Telecom & navigation
  4. Mobile phones
  5. Car kits
  6. Crux
  7. SWRTY-61P
SWRTY-61P

Crux SWRTY-61P User manual

  • Hello! I've reviewed the user manual for the Crux SWRTY-61P Radio Replacement Interface. This device is designed to retain factory features in select Toyota vehicles, including steering wheel controls, the JBL amplifier, and backup camera when replacing the stock radio with an aftermarket one. I understand that it includes adapters for USB and antenna. I'm ready to answer your questions about its installation, dip switch settings, and compatibility.
  • What features does the SWRTY-61P retain?
    What vehicles are compatible with the SWRTY-61P?
    Is any dip switch setting required?
SWRTY-61P
SWC Module
TOY Box TY-61P Harness Speaker
Harness
SWC Cable USB Adapter Antenna Adapter
Crux Interfacing Solutions • Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.102221
SWRTY-61P
Radio Replacement Interface with Steering Wheel Control and
JBL Amplier Retention for Select Toyota Vehicles 2018-Up
1 of 3
RADIO REPLACEMENT
SWC RETENTION
+
R
INTERFACING SOLUTIONS
- Retains factory features in select Toyota vehicles while funconing with an aermarket radio.
- Pre-programmed to retain factory Steering Wheel Controls.
- Retains the factory JBL amplier.
- Retains factory back-up camera and sensors.
- Retains factory bird’s eye view feature (if equipped).
- Retains factory Auxiliary Audio Input.
- Includes factory USB retenon adapter cable.
- Includes antenna adapter.
PRODUCT FEATURES:
PARTS INCLUDED:
INSTALLATION DIAGRAM:
Crux Interfacing Solutions • Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.102221
2 of 3
RADIO REPLACEMENT
SWC RETENTION
+
R
INTERFACING SOLUTIONS
SWRTY-61P
Radio Replacement Interface with Steering Wheel Control and
JBL Amplier Retention for Select Toyota Vehicles 2018-Up
INSTALLATION INSTRUCTIONS:
1. Connect the SWRTY-61P T-harness
to the aermarket radio harness.
Refer to the diagram on page 1 for
wire color codes.
2. Remove the padded trim above the glove compartment.
3. Carefully pull out the trim under the
radio.
4. Remove the small trim next to the
shier.
5. Remove the AC control panel below
the radio.
6. Unplug the connector behind the AC
control panel.
7. Pull out the radio and unplug the
connectors.
8. Mate the factory radio connectors
to the SWRTY-61P T-harness. Test
for funconality then install the
aermarket radio.
Crux Interfacing Solutions • Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.1022213 of 3
RADIO REPLACEMENT
SWC RETENTION
+
R
INTERFACING SOLUTIONS
DIP SWITCH SETTINGS:
TOYOTA STEERING WHEEL CONTROL DIP SWITCH SETTING:
AFTERMARKET RADIO DIP SWITCH SETTINGS:
NOTE: Insulate the Blue/Yellow wire or 3.5mm plug if not being used.
DIP: 5 6 7 8
Toyota OFF ON OFF ON
SWC MODULE
ON RADIO VEHICLE
1 2 3 4 5 6 7 8
RADIO BRAND: DIP: 1 2 3 4
Atoto, Dual, Farenheit, Jensen, Pioneer
Power Acoustik, Soundstream
Blaupunkt, Most o-brand Radios
Alpine
Clarion
Kenwood
JVC
Boss, Old Sony
New Sony
OFF OFF ON ON
OFF OFF ON ON
OFF OFF ON ON
OFF OFF OFF OFF
OFF ON ON OFF
OFF ON ON ON
OFF ON OFF ON
OFF ON OFF OFF
OFF OFF ON OFF
SWC MODULE
ON RADIO VEHICLE
1 2 3 4 5 6 7 8
NOTE: For Atoto, Blaupunkt, Dual, Farenheit, Power Acoustik, Soundstream, and most o-brand radios,
check the aftermarket radio’s manual to see if the SWC buttons need to be programmed.
3.5MM SWC CABLE
Plug in the 3.5MM to 4-Pin SWC cable to the SWC module.
VEHICLE APPLICATIONS:
SWRTY-61P
Radio Replacement Interface with Steering Wheel Control and
JBL Amplier Retention for Select Toyota Vehicles 2018-Up
Factory bird’s eye view and proximity sensors feature is retained.
Image on the le is from a 2019 Toyota Camry using a Sony radio.
RED to SWC Key 1
WHITE to SWC Key 2
SHIELD to SWC Ground
For aermarket radios that have wires for SWC connecons,
cut o the 3.5mm plug on the Crux SWC Cable and connect
the SWC wires per the diagram on the right:
Note that there are some radios that only have SWC1 and SWC2,
in this case “shield” does not need to be connected.
Toyo ta
2020-Up
2019-Up
2018-Up
2019-Up
2018-Up
2020-Up
4Runner
Avalon
Camry
CH-R
Corolla
Highlander
2019-Up
2020-Up
2018-Up
2020-Up
2020-Up
RAV4
Sequoia
Sienna
Tacoma
Tundra
NOTE: For JBL amplied vehicles ONLY.
/