Dwyer Series BV2IM User manual

Brand: Dwyer

Model: Series BV2IM

Type: User manual

Bulletin V-BV2IM

The Series BV2IM SS Ball Valve with ISO Mounting Pad provides an

economical, high quality stainless steel ball valve with an ISO mounting

pad. The ISO 5211 mounting pad accepts direct mounting of pneumatic

and electric actuators. The Series BV2IM body, ends, ball, and stem are

made from high quality 316 SS. The valve offers a stem design providing

additional protection against blow outs. Full port design allows for

maximum flow rates with minimal pressure drops.

OPERATIONS

Manual Operations-To open or close the valve, turn the handle 90° (1/4

turn). Valve in OPEN position: the handle is parallel (in line) with the valve

pipeline. Valve in CLOSED position: the handle is perpendicular

(crossed) with the valve or pipeline.

Automated Operation-Valves with actuators should be checked for

stem alignment. Most applications are direct mount to the actuator,

greatly reducing any sideload or increased torque. Make sure that all

insert adapters are properly placed on the valve stem and fully engaged

in the actuator.

INSTALLATION

General Information for On-Site Installation-The valve may be fitted in

any position in the pipeline. For automated operation, W.E. Anderson

recommends that the valve and actuator be installed vertically in case of

valve leakage, although this is not necessary for proper operation of the

valve. Prior to installation, inspect valve and pipe ends to make sure they

are free from debris. Materials trapped inside the valve can cause

damage to the seats and result in leakage. Clean pipe ends and check

for proper threading to prevent damage to valve internals. Use a PTFE

based thread sealant applied to the pipe threads. Use a smooth wrench

on the hex portion of the valve, not the valve body, to tighten. Use pipe

wrenches on pipe and pipe fittings only.

DWYER INSTRUMENTS, INC.

Phone: 219/879-8000 www.dwyer-inst.com

P.O. BOX 373 • MICHIGAN CITY, INDIANA 46360, U.S.A. Fax: 219/872-9057 e-mail: [email protected]

Specifications - Installation and Operating Instructions

Series BV2IM SS Ball Valve with ISO Mounting Pad

SPECIFICATIONS

Service: Compatible liquids and gases.

Line Size: 1/4 to 3˝.

End Connection: Female NPT.

Pressure Limit: 1000 psi (69 bar).

Wetted Materials:

Body and ends: CF8M;

Ball and stem: 316 SS;

Seat: RTFE.

Temperature Limit: 450°F (232°C); 366°F (186°C) steam maximum.

Other Materials:

Gland nut, belleville washer, lock washer, handle nut, handle, and

packing nut: 304 SS;

Thrust washer, body seal, and stem packing: PTFE.

WARRANTY

The Series BV2IM warranties from defects in materials and workmanship

are covered for (1) year from the date of purchase. In the unlikely event

the valve should fail, the unit can be returned to the factory for warranty

repair if the warranty period has not expired. Be sure to include a brief

description of the problem plus any relevant application notes. Contact

our customer service department for an RGA number and to set up the

return.

NPT

Size

/4˝

3/8˝

1/2˝

3/4˝

-1/4˝

-1/2˝

2˝

2-1/2˝

3˝

ISO

5211

03/04

F03/04

04/05

05/07

F05/07

F07/10

.56

2.56

2.95

3.15

.54

.33

.72

5.51

7.28

8.07

.69

1.69

1.64

1.74

.99

.19

.59

3.14

3.20

3.67

odel

V2IM00

V2IM01

V2IM02

V2IM03

V2IM04

BV2IM05

BV2IM06

BV2IM07

BV2IM08

BV2IM09

Dimensions (in)

Weight

lb (kg)

0.88 (0.40)

0.95 (0.43)

1.45 (0.66)

2.36 (1.07)

.50 (1.59)

.21 (1.91)

.90 (3.58)

17.60 (7.98)

25.30(11.48)

Dwyer Series BV2IM User manual

Dwyer Series BV2IM User manual

Dwyer Series BV2IM User manual

Related papers

Other documents