ADJ Focus Spot 2X User manual

User Instructions

FOCUS SPOT 2X

Europe Energy Saving Notice

Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical prod-

ucts when they are not in use. To avoid power consumption in idle mode, disconnect all electrical

equipment from power when not in use. Thank you!

instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying

product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection

claimed includes all forms and matters of copyrightable materials and information now allowed by

statutory or judicial law or hereinafter granted. Product names used in this document may be

trademarks or registered trademarks of their respective companies and are hereby acknowledged.

All non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of

their respective companies.

ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,

equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic

loss associated with the use or reliance of any information contained within this document, and/or as

a result of the improper, unsafe, unsucient and negligent assembly, installation, rigging, and opera-

tion of this product.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

FCC RADIO FREQUENCY INTERFERENCE WARNINGS & INSTRUCTIONS

This product has been tested and found to comply with the limits as per Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installation.

This device uses and can radiate radio frequency energy and, if not installed and used in accordance with

the included instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this device does cause harmful

interference to radio or television reception, which can be determined by turning the device off and on, the

user is encouraged to try to correct the interference by one or more of the following methods:

· Reorient or relocate the device.

· Increase the separation between the device and the receiver.

· Connect the device to an electrical outlet on a circuit different from which the radio receiver is

connected.

· Consult the dealer or an experienced radio/TV technician for help.

DOCUMENT VERSION

Due to additional product features and/or enhancements, an updated version of this document

may be available online.

Please check www.adj.com for the latest revision/update of this manual before beginning

installation and/or programming.

09/24/19

1 1.0

16/18 Initial Version

Date

Document

Version

Software

Version >

DMX Channel Mode

Notes

ADJ Products, LLC - www.adj.com - Focus Spot 2X User Manual Page 2

Focus Spot 2X Table of Contents

Introduction

Features I Warranty Registration I Installation

Safety Guidelines

Overview

Installation

DMX Set Up

DMX Addressing

DMX Modes & Values

System Menu

Master-Slave Set Up I Manual Zoom

UC IR & Airstream Remote Control

Target Mode

Dimmer Curve Chart

Gobo Replacement & Gobos

Remove the Head Casing

Dimensional Drawings

Fuse Replacement I Multiple Unit Power Linking

Trouble Shooting I Cleaning

Limited Warranty (USA Only)

Technical Specications

3

4

5

8

9

11

13

14

17

20

21

22

23

24

25

26

27

28

29

ADJ Products, LLC - www.adj.com - Focus Spot 2X User Manual Page 3

Focus Spot 2X Introduction

Unpacking: Thank you for purchasing the Focus Spot 2X by ADJ Products, LLC. Every unit has been

thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping

carton for damage that may have occurred during shipping. If the carton appears to be damaged,

carefully inspect your xture for any damage and be sure all accessories necessary to operate the unit

has arrived intact. In the case damage has been found or parts are missing, please contact our toll free

customer support number for further instructions. Do not return this unit to your dealer without rst

contacting customer support.

Introduction: The Focus Spot 2X is a DMX intelligent, moviing head, LED fixture. This xture can be

used in a stand alone mode or connected in a Master/Slave conguration. This product is intended to

be used by professionally trained personnel only and is not suitable for private use.

These instructions contain important safety information regarding the use and maintenance of this

unit. Please keep this manual with the unit, for future reference.

Customer Support: Contact ADJ Service for any product related service and support needs. Also visit

forums.adj.com with questions, comments or suggestions.

Parts: To purchase parts online visit:

http://parts.americandj.com (US)

http://www.adjparts.eu (EU)

ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST

Voice: 800-322-6337 | Fax: 323-832-2941 | [email protected]

ADJ SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET

Voice: +31 45 546 85 60 | Fax: +31 45 546 85 96 | [email protected]

ADJ PRODUCTS LLC USA

6122 S. Eastern Ave. Los Angeles, CA. 90040

323-582-2650 | Fax 323-532-2941 | www.adj.com | info@adj.com

ADJ SUPPLY Europe B.V

Junostraat 2 6468 EW Kerkrade, The Netherlands

+31 (0)45 546 85 00 | Fax +31 45 546 85 99

www.adj.eu | [email protected]

ADJ PRODUCTS GROUP Mexico

AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000

+52 (728) 282-7070

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,

doing so will void your manufactures warranty. In the unlikely event your unit may require service

please contact ADJ Products, LLC.

PLEASE recycle the shipping carton when ever possible.

Focus Spot 2X Features

Focus Spot 2X Warranty Registration

The Focus Spot 2X carries a 2 year limited warranty. Please fill out the enclosed warranty card to

validate your purchase. All returned service items whether under warranty or not, must be freight pre-

paid and accompany a return authorization (R.A.) number. The R.A. number must be clearly written on

the outside of the return package. A brief description of the problem as well as the R.A. number must

also be written down on a piece of paper included in the shipping carton. If the unit is under warranty,

you must provide a copy of your proof of purchase invoice. You may obtain a R.A. number by con-

tacting our customer support team on our customer support number. All packages returned to the

service department not displaying a R.A. number on the outside of the package will be returned to the

shipper.

ADJ Products, LLC - www.adj.com - Focus Spot 2X User Manual Page 4

• Individual Color and Gobo Wheels

• 8 Colors + White

• 6 Rotating Replaceable Gobos + Open

• 6 Facet Circular Prism & 6 Facet Linear Prism

• Electronic Dimming 0-100%

• DMX-512 protocol

• 3-Pin DMX Connections

• 2 DMX Channel Modes: 16/18

• Multiple Unit Power Linking (See page 27)

Included:

1 x powerCON Cable

1 x Mounting Bracket

ADJ Products, LLC - www.adj.com - Focus Spot 2X User Manual Page 5

Focus Spot 2X Safety Guidelines

• Do not attempt to operate this unit if the power cord has been frayed or broken. Do not attempt to

remove or break o the ground prong from the electrical cord. This prong is used to reduce the risk

of electrical shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Never plug this unit in to a dimmer pack

• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6”

(15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to be walked on or pinched by

items placed upon or against them, paying particular attention to the point they exit from the unit.

• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 27

for cleaning details.

• Heat -The appliance should be situated away from heat sources such as radiators, heat registers,

stoves, or other appliances (including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the fixture.

C. The fixture does not appear to operate normally or exhibits a marked change in performance.

D. The fixture has fallen and/or subjected to extreme handling.

ADJ Products, LLC - www.adj.com - Focus Spot 2X User Manual Page 6

Focus Spot 2X Safety Guidelines

RISK GROUP 3 - RISK OF EXPOSURE TO ULTRAVIOLET (UV) RADIATION!

FIXTURE EMITS HIGH INTENSITY ULTRAVIOLET (UV) LIGHT FROM THE UV LED.

WEAR PROPER EYE AND SKIN PROTECTION.

AVOID PROLONGED PERIODS OF EXPOSURE TO THE UV LED.

AVOID WEARING WHITE COLOR CLOTHING AND/OR USING (UV) PAINTS ON SKIN.

AVOID DIRECT EYE AND/OR SKIN EXPOSURE AT DISTANCES SHORTER THAN 11 feet (3.3m).

DO NOT OPERATE FIXTURE WITH DAMAGED OR MISSING EXTERNAL COVER.

DO NOT LOOK DIRECTLY INTO THE (UV) LIGHT AND/OR VIEW (UV) LIGHT DIRECTLY WITH

OPTICAL INSTRUMENTS THAT MAY CONCENTRATE THE LIGHT/RADIATION OUTPUT.

INDIVIDUALS SUFFERING FROM A RANGE OF EYE CONDITIONS, SUNLIGHT EXPOSURE

DISORDERS, OR INDIVIDUALS USING PHOTOSENSITIVE MEDICATION, MAY RECEIVE

DISCOMFORT IF EXPOSED TO THE ULTRAVIOLET (UV) LIGHT EMITTED FROM THIS FIXTURE.

ADJ Products, LLC - www.adj.com - Focus Spot 2X User Manual Page 7

Focus Spot 2X Safety Guidelines

POTENTIAL INTERNAL FIXTURE DAMAGE FROM EXTERNAL SOURCES OF LIGHT BEAMS

External sources of light beams from direct sunlight, lighting moving head xtures, and lasers, which

are focused directly towards the exterior housing and/or penetrate the front lens opening of ADJ

lighting xtures, can cause severe internal damage including burning to optics, dichroic color lters,

glass and metal gobos, prisms, animation wheels, frost lters, iris, shutters, motors, belts, wiring,

discharge lamps, and LEDs.

This issue is not specic only to ADJ lighting xtures, it is a common issue with lighting xtures

from all manufacturers. Although there is no true way to fully prevent this issue from happening, the

guidelines below can prevent any potential damage from occurring if followed. Contact ADJ Service

for more details.

DO NOT EXPOSE THE FIXTURE AND/OR FRONT LENS OPENING TO LIGHT BEAMS FROM DIRECT

SUNLIGHT, OTHER LIGHTING MOVING HEAD FIXTURES, AND LASERS WHILE UNPACKING,

INSTALLATION, USE, AND EXTENDED IDLE TIMES OUTDOORS.

DO NOT FOCUS A LIGHT BEAM FROM ONE LIGHTING FIXTURE DIRECTLY TOWARDS ANOTHER.

ADJ Products, LLC - www.adj.com - Focus Spot 2X User Manual Page 8

Focus Spot 2X Overview

7

8 9 10

1 2 3 4

5

6

1. IR Receiver

2. Master Active LED

3. LCD Display

MENU Button

UP Button

DOWN Button

ENTER Button

4. Sound Active LED

5. Slave Active LED

6. DMX Active LED

7. Manual Zoom Control

8. 3-Pin DMX In/Out

9. powerCON In/Out

10. Fuse (3.15A)

ADJ Products, LLC - www.adj.com - Focus Spot 2X User Manual Page 9

Focus Spot 2X Installation

The Focus Spot 2X is fully operational in three dierent mounting positions, hanging upside-down

from a ceiling or trussing, sideways on trussing, or set on a at level surface. Be sure this xture is

kept at least 12m (40ft) away from any ammable materials (decoration etc.). Always use and install

the supplied safety cable as a safety measure to prevent accidental damage and/or injury in the

event the clamp fails (see next page). Never use the carrying handles for secondary attachment.

When installing the unit, the trussing or area of installation must be able to hold 10 times the weight

without any deformation. When installing the unit must be secured with a secondary safety attachment,

e.g. and appropriate safety cable. Never stand directly below the unit when mounting, removing, or

servicing the unit.

Overhead mounting requires extensive experience, including calculating working load limits, installation

material being used, and perodic safety inspection of all installation material and unit. If you lack

these qualications, do not attempt the installation yourself.

These installaiton should be checked by a skilled person once a year.

ADJ Products, LLC - www.adj.com - Focus Spot 2X User Manual Page 10

Focus Spot 2X Installation

Screw one clamp via a M12 screw and nut into the bracket. Attach the bracket to the respective holes

located on the bottom of the Focus Spot 2X. Tighten and secure the bracket screws. Pull the safety

cable through the opening(s) located on the base plate and over the trussing system or a safe xation

spot. Insert the end in the carabine and tighten the safety screw.

NOTICE: The suitable enviromental temperature for this lighting xture is between -25˚ C to 45˚ C.

Do not place this lighting xture in an enviroment where the temperatures are under or above the

temperatures stated above. This will allow the xture to run at its best and help prolong the xture

life.

SAFETY CABLE

ATTACHMENT POINT

SAFETY CABLE

ATTACHMENT POINT

BRACKET

ATTACHMENT POINT

BRACKET

ATTACHMENT POINT

SAFETY CABLE

(NOT INCLUDED)

CLAMP

(NOT INCLUDED)

BRACKET

ADJ Products, LLC - www.adj.com - Focus Spot 2X User Manual Page 11

Focus Spot 2X DMX Set Up

DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of commu-

nication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions

from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture

via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only

have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of dierent manufactures to be

linked together and operate from a single controller, as long as all xtures and the controller are DMX

compliant. To ensure proper DMX data transmission, when using several DMX fixtures try to use

the shortest cable path possible. The order in which fixtures are connected in a DMX line does not

influence the DMX addressing. For example; a fixture assigned a DMX address of 1 may be placed

anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is

assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that

unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation): The Focus Spot 2X can be controlled

via DMX-512 protocol. The DMX address is set on the front panel of the Focus Spot 2X. Your unit and your

DMX controller require a standard 3-pin XLR connector for data input and data output (Figure 1). We

recommend Accu-Cable DMX cables. If you are making your own cables, be sure to

use standard 110-120 Ohm shielded cable (This cable may be purchased at almost

all pro lighting stores). Your cables should be made with a male and female XLR

connector on either end of the cable. Also remember that DMX cable must be

daisy chained and cannot be split.

Figure 1

Notice: Be sure to follow gures two and three when making your own cables. Do not use the ground

lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the

shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a

short circuit and erratic behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

1

2

3

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

1

2

3

1

2

3

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 2

Figure 3

1 Ground

XLR Male Socket

XLR Pin Conguration

3 Hot

2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

ADJ Products, LLC - www.adj.com - Focus Spot 2X User Manual Page 12

Special Note: Line Termination.

When longer runs of cable are used, you may need to use a termina-

tor on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is

connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted

in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable

terminator (ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior.

Focus Spot 2X DMX Set Up

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

1

2

3

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

1

2

3

1

2

3

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 4

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin DMX-512 data cables for DATA trans-

mission in place of 3-pin. 5-pin DMX xtures may be implemented in a 3-pin DMX line. When inserting

standard 5-pin data cables in to a 3-pin line a cable adaptor must be used, these adaptors are readily

available at most electric stores. The chart below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Pin 1

Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

ADJ Products, LLC - www.adj.com - Focus Spot 2X User Manual Page 13

All xtures should be given a DMX starting address when using a DMX controller, so the correct xture

responds to the correct control signal. This digital starting address is the channel number from which

the xture starts to “listen” to the digital control signal sent out from the DMX controller. The assignment

of this starting DMX address is achieved by setting the correct DMX address on the digital control

display on the xture.

You can set the same starting address for all xtures or a group of xtures, or set dierent addresses

for each individual xture. Setting all xtures to the same DMX address will cause all xtures to react

in the same way, in other words, changing the settings of one channel will aect all the xtures

simultaneously.

If you set each xture to a dierent DMX address, each unit will start to “listen” to the channel number

you have set, based on the quantity of DMX channels of each xture. That means changing the settings

of one channel will only aect the selected xture.

In the case of the Focus Spot 2X, when in 16 channel mode you should set the starting DMX address

of the rst unit to 1, the second unit to 17 (16 + 1), the third unit to 33 (17 + 16), and so on. (See the

chart below for more details.)

Focus Spot 2X DMX Addressing

Channel Mode

Unit1

Address

Unit2

Address

Unit3

Address

Unit4

Address

16Channels 1 17 33 49

18Channels 1 19 37 55

ADJ Products, LLC - www.adj.com - Focus Spot 2X User Manual Page 14

Focus Spot 2X DMX Modes & Values

1 1 PAN MOVEMENT 8-BIT:

2

PAN FINE 16-BIT:

Fine Control of Pan Movement

2 3 TILT MOVEMENT 8-BIT:

3 5

Functions

16 Channels 18 Channels Values

Open / White

Red

Blue

Green

Yellow

Pink

Light Blue

Light Green

Light Yellow

Clockwise Rotation Fast-Slow

Stop

Counter-Clockwise Rotation Fast-Slow

000-014

015-028

029-042

043-056

057-070

071-084

085-098

099-112

113-127

128-189

190-193

194-255

000-255

GOBO WHEEL:

Open

Gobo 1

Gobo 2

Gobo 3

Gobo 4

Gobo 5

Gobo 6

Open Shake

Gobo 1 Shake

Gobo 2 Shake

Gobo 3 Shake

Gobo 4 Shake

Gobo 5 Shake

Gobo 6 Shake

Clockwise Rotation Fast-Slow

Stop

Counter-Clockwise Rotation Fast-Slow

000-009

010-018

019-027

028-036

037-046

047-055

056-063

064-073

074-082

083-091

092-100

101-110

111-119

120-127

128-189

190-193

194-255

4 6

RGOBO (ROTATING GOBO):

Indexing

Clockwise Rotation Slow-Fast

Stop

Counter-Clockwise Rotation Fast-Slow

000-127

128-189

190-193

194-255

PRISMS:

No Effect

Prism 1

Prism 2

000-015

016-135

136-255

4

TILT FINE 16-BIT:

Fine Control of Tilt Movement

000-255

5 7

6 8

COLOR WHEEL:

ADJ FOCUS SPOT 2X

DMX Channel Values & Functions

Supports Software Version > 1.0

Features subject to change without notice

*Rotation direction (Clockwise/Counter-Clockwise) and control of effects depends on head orientation and Pan/Tilt settings*

ADJ Products, LLC - www.adj.com - Focus Spot 2X User Manual Page 15

Focus Spot 2X DMX Modes & Values

7 9

Functions

16 Channels 18 Channels Values

LED Off

LED On

Strobing Slow-Fast

LED On

Slow Open-Fast Close

LED On

Fast Open-Slow Close

LED On

Random Strobing Slow-Fast

LED On

000-007

008-015

016-131

132-139

140-181

182-189

190-231

232-239

240-247

248-255

UV SHUTTER & STROBE:

LED Off

LED On

Strobing Slow-Fast

LED On

Slow Open-Fast Close

LED On

Fast Open-Slow Close

LED On

Random Strobing Slow-Fast

LED On

000-007

008-015

016-131

132-139

140-181

182-189

190-231

232-239

240-247

248-255

9 11

SHOWS:

Off

Show 1

Show 2

Show 3

Show 4

Random Show Sound Active

0

001-021

022-041

042-061

062-081

082-255

12 14

SHUTTER & STROBE:

8 10

MASTER DIMMER:

000-255

0% - 100%

10 12

UV MASTER DIMMER:

000-255

0% - 100%

11 13

FOCUS:

000-255

0% - 100%

13 15

SHOW SPEED:

000-255

Slow-Fast

DIMMER MODES:

Standard

Stage

TV

Architectural

Theatre

Default to Unit Setting

000-020

021-040

041-060

061-080

081-100

101-255

14 16

15 17

PAN/TILT SPEED:

000-255

Fast-Slow

ADJ Products, LLC - www.adj.com - Focus Spot 2X User Manual Page 16

Focus Spot 2X DMX Modes & Values

Functions

16 Channels 18 Channels Values

SPECIAL FUNCTIONS:

No Function

Enable Blackout with Pan/Tilt Movement

Disable Blackout with Pan/Tilt Movement

Enable Blackout with Color Change

Disable Blackout with Color Change

Enable Blackout with Gobo Change

Disable Blackout with Gobo Change

Pan/Tilt Reset

Color Wheel Reset

Gobo Wheel Reset

Effect Reset

No Function

Reset All

No Function

000-069

070-079

080-089

090-099

100-109

110-119

120-129

130-139

140-149

150-159

160-169

170-199

200-209

210-255

16 18

ADJ Products, LLC - www.adj.com - Focus Spot 2X User Manual Page 17

Focus Spot 2X System Menu

SYSTEM MENU

The xture includes an easy to navigate system menu control panel display where all necessary

settings and adjustments are made. (See image below) During normal operation, pressing the MENU

button once will access the xture’s main menu. Once in the main menu, you can navigate through

the dierent functions and access the sub-menus with the UP and DOWN buttons. When you reach

a eld that requires adjusting, press the ENTER button to access that eld and use the UP and

DOWN buttons to adjust the eld. Pressing the ENTER button once more will conrm your setting.

You may exit the main menu at any time without making any adjustments by pressing the MENU

button.

ADJ Products, LLC - www.adj.com - Focus Spot 2X User Manual Page 18

Focus Spot 2X System Menu

001-XXX

Master/Slave Setting

DMX Channel Mode Selection

DMX Addressing

16Chan / 18Chan

OPTIONS DESCRIPTIONMENU

Target Mode Selection

DMX Address

Channel Mode

Slave Mode Master / Slave 1 / Slave 2

Show Mode

Show 0 / Show 1 / Show 2 / Show 3 / Show 4

Mode 0 / Mode 1 / Mode 2 / Mode 3 / Mode 4

Show Mode Selection

Target Mode

Sound Mode Activation

On / Off

Sound Mode

Sound Sensitivity Adjustment

0~100

Sound Sense

DMX State Setting

Master Slave / Blackout / Last State

DMX State

Dimmer Curve Dimming Curve SettingStandard / Stage / TV / Architec / Theatre

Pan Invert Pan InversionNormal / Invert

Tilt Invert Tilt InversionNormal / Invert

Back Light Back Light SettingOn / Off

Auto Test Auto Test

LED Temp. Current LED Temperature

XXX

Fixture Time Current Fixture Time

XXX

Firmware Version Current Software Version

VX.X

Pro Default Restore Factory DefaultsOn / Off

Reset Reset MotorsYes / No

ADJ Products, LLC - www.adj.com - Focus Spot 2X User Manual Page 19

Focus Spot 2X System Menu

DMX ADDRESS - In this submenu you can nd and set your desired DMX address.

DMX CHANNEL MODE - In this submenu you can nd and set your desired DMX channel mode.

SLAVE MODE - In this submenu you are able to designate the unit(s) as either a “master” or “slave”

in a master-slave setup.

SHOW MODE - In this submenu you can select 1 of 5 (0-4) built-in shows to run.

TARGET MODE - In this submenu you are able to select 1 or 5 (0-4) target modes for the unit to

follow. Target mode is a restrictive pan/tilt control mode limiting the pan/tilt movements to a certain

degree. See page 22 for a diagram of the Target mode movements.

SOUND MODE - In this submenu you can activate and deactivate sound active mode.

SOUND SENSE - In this submenu you can adjust and set the sound sensitivity level for sound active

mode.

DMX STATE - This submenu setting is used as a precaution mode in case the DMX signal is

lost or interrupted. The operating mode chosen in this submenu is the running mode the xture

will go into when the DMX signal is lost. Listed below are the 3 modes.

• Master Slave - This setting will have the xture automatically go into master/slave setup. The unit

will go into the setting that is selected under “SLAVE MODE”.

• Blackout - This setting will have the xture automatically go into stand by mode (blackout).

• Last State - This setting will have the xture stay in the last DMX setup.

DIMMER CURVE - In this submenu you are able to select 1 or 5 dimmer curves. See page 23 for the

dimmer curve chart for more information.

PAN INVERT - In this submenu you can activate pan inversion.

TILT INVERT - In this submenu you can activate tilt inversion.

BACK LIGHT - In this submenu you can have the display backlight turn o after a minute of no acitivty.

AUTO TEST - In this submenu you can run an auto test of the functions.

LED TEMP. (TEMPERATURE) - In this submenu you can check the current running temperature.

FIXTURE TIME - In this submenu you can check the xture running time.

FIRMWARE VERSION - In this submenu you can check the current software version.

FACTORY RESTORE - In this submenu you restore the factory (default) settings.

RESET - In this submenu you can reset the motors.

Page is loading ...

ADJ Focus Spot 2X User manual

ADJ Focus Spot 2X User manual

Related papers

Other documents