OWNER’S MANUAL
OM-237 679D
2010−02
RFCS - RJ45 Foot Control
1. Safety
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury. The possible ha-
zards are shown in the adjoining symbols or explained in
the text.
Breathing welding fumes and gases can harm your
health. Welding requires good ventilation. If ventilation is
impossible, such as when welding in a confined space,
use an air-supplied respirator.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury. The possible ha-
zards are shown in the adjoining symbols or explained in
the text.
Welding sparks can cause fire or explosion. Move flam-
mables away. Do not weld on closed tanks or barrels −
they can explode. Clean tanks or barrels properly.
NOTICE
Indicates statements not related to personal injury.
Indicates special instructions.
Arc rays can burn eyes and skin − wear a welding helmet
with correct filter, and cover exposed skin with nonflam-
mable clothing.
Beware of electric shock from welding electrode or wiring.
Touching the electrode while in contact with the work or
ground can cause electric shock. Always wear dry
gloves. Keep all panels and covers closed.
Wear safety glasses with side shields.
2. Typical Connections And Operation
805 166-A
1 Welding Power Source Foot
Control Receptacle
2 Strain Relief (Optional
Installation)
3 Cord
4 Foot Control
If desired, route cord through strain
relief. Remove screw as shown
from welding power source, and
use screw to secure strain relief.
Plug one end of cord into receptacle
on welding power source. Plug
remaining end into receptacle on
back of foot control.
OPERATION:
Press pedal lightly to turn weld
output and gas flow on. Press pedal
further to increase weld output.
Raise pedal to reduce amperage,
crater-out, and turn off weld output
and gas flow.
. See welding power source
Owner’s Manual for additional
information.
Tools Needed:
1
3
2
4
Torx T25
OM-237 679 Page 2
3. Troubleshooting
Trouble Remedy
No weld output Be sure foot control cord is plugged into matching receptacles on welding power source and back of
foot control.
Not enough weld amperage Set weld amperage to highest desired value on welding power source Material Thickness/Amperage
control. Amperage available with foot control is 10 amps to max value set on Thickness/Amperage
control.
4. Parts
Description
Part
No.
300 432
Quantity
RFCS−RJ45 (FOOT CONTROL)
237 678 FOOT CONTROL, RFCS−RJ45 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
237 676 CABLE CONNECTING, W/CONNECTORS 14 FT 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
235 493 CLAMP, STL CUSH .187 DIA X .281 MTG HOLE ZINC PLD 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
-
1
-
2
Miller LJ000000 Owner's manual
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Miller RFCS - RJ45 FOOT CONTROL Owner's manual
-
-
-
Miller RFCS-14 Owner's manual
-
-
-
-
-
-
Unitor NT 456 CC/CV WCC Owner's manual
