Ingersoll-Rand 650875-XXX-C User manual

Brand: Ingersoll-Rand

Model: 650875-XXX-C

Type: User manual

This manual is also suitable for

Heat Pump 650875-XXX-C

INGERSOLL RAND COMPANY LTD

209 NORTH MAIN STREET – BRYAN, OHIO 43506



(800) 495-0276

y

FAX (800) 892-6276

© 2011 CCN 99834913

www.ingersollrandproducts.com

OPERATOR’S MANUAL 650875-XXX-C

INCLUDING: SPECIFICATIONS, SERVICE KITS, GENERAL INFORMATION, TROUBLESHOOTING.

INCLUDE MANUALS: 66651-B Air Motor (pn 97999-869), 66236-XXX-B Lower Pump End (pn 97999-489) &

S-632 General Information Manual (pn 97999-624).

RELEASED: 1-14-00

REVISED:

5-19-11

(REV. 0

4)

650875-XXX-C

EXTRUSION PUMP SERIES

Carbon Steel

READ THIS MANUAL CAREFULLY BEFORE INSTALLING,

OPERATING OR SERVICING THIS EQUIPMENT.

It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.

10” AIR MOTOR

20:1 RATIO

6” STROKE

SERVICE KITS

Use only genuine ARO® replacement parts to assure compat-

ible pressure rating and longest service life.

637110 for repair of air motor section.

637128-XX4-B for repair of lower pump end. Refer to the chart

on page 2 for description of -XXX options.

SPECIFICATIONS

Model Series

(refer to option chart)

. . . . . . . . . . . 650875-XXX-C

Pump Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air Operated, Extrusion

Double Acting Pump

Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20:1

Air Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66651-B

Motor Repair Kit . . . . . . . . . . . . . . . . . . . . . . . 637110

Motor Diameter . . . . . . . . . . . . . . . . . . . . . . . 10” (25.4 cm)

Stroke (double acting) . . . . . . . . . . . . . . . . . 6” (15.2 cm)

Air Inlet (female) . . . . . . . . . . . . . . . . . . . . . . . 3/4 - 14 N.P.T.F. - 1

Air Exhaust (female). . . . . . . . . . . . . . . . . . . . 1-1/4 - 11-1/2 N.P.S.M.

Lower Pump End Series . . . . . . . . . . . . . . . . . . 66236-XXX-B

Lower Pump Repair Kit . . . . . . . . . . . . . . . . 637128-XX4-B

Material Outlet (female) . . . . . . . . . . . . . . . 1-1/2 - 11-1/2 N.P.T.F. - 1

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 lbs (65.3 kgs)

PUMP PERFORMANCE

Air Inlet Pressure Range . . . . . . . 30 - 90 p.s.i.g. (2.1 - 6.2 bar)

Fluid Pressure Range . . . . . . . . . . . . 600 - 2250 p.s.i.g. (41.4 - 155.2 bar)

Maximum Rec'd Cycles / Minute . . . . . . . . . 70

Displacement In. Per Cycle. . . . . . . . . . . . . . . . 40.4

Volume / Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . 22.4 oz. (661.8 ml)

Cycles Per Gallon . . . . . . . . . . . . . . . . . . . . . . . . 5.7

Flow @ 70 Cycles / Minute . . . . . . . . . . . . . . . . 12.2 g.p.m. (46.3 l.p.m.)

Noise Level @ 60 p.s.i. - 40 c.p.m. . . . . . . . 84.8 db(A)

c

Accessories Available . . . . . . . . . . . . . . . . 66542 Wall Mount Bracket

65139 Floor Mount

66718 Silencer

c

The pump sound pressure level has been updated to an Equivalent Continuous

Sound Level (LAeq) to meet the intent of ANSI S1.13-1971, CAGI-PNEUROP S5.1

using four microphone locations.

y

y

y

PUMP DATA

“B”

“A”

“C”

“D”

IMPORTANT

This is one of four documents which support the pump. Re-

placement copies of these forms are available upon request.

:

650875-XXX-C Model Operator’s Manual (pn 97999-875)



S-632 General Information - Industrial Piston Pumps (pn

97999-624)



66236-XXX-B Lower Pump End Operator’s Manual (pn 97999-489)



66651-B Air Motor Operator’s Manual (pn 97999-869)

Figure 1

MODEL 650875-XXX-C

NOTE: Dimensions are shown in inches and (mm) and are supplied for reference only.

Air Inlet (female)

3/4 - 14 N.P.T.F. - 1 (not shown)

Material Outlet (female)

1-1/2 - 11-1/2 N.P.T.F. - 1

(90° from 1-1/4 - 11-1/2

N.P.S.M. air exhaust)

66651-B Air Motor

(see manual 66651-B)

66236-XXX-B Lower Pump

(see manual 66236-XXX-B)

Spacer Section

Air Exhaust (female)

1-1/4 - 11-1/2 N.P.S.M.

Connector (see  gure 2)

Y6-128-C Hex Cap Screw (6)

Y14-750-K Lock Washer (6)

93866 Spacer Rod (3)

“A”

(mm)

“B”

(mm)

“C”

(mm) “D” (mm)

51-7/32”

(1300.9)

31-3/8"

(796.9)

19-15/16"

(506.4)

2-7/8”

(73.1)

d



Tested with 66718 silencer installed.

d

Page 2 of 2 650875-XXX-C (en)

PN 97999-875

650875- X X X -C

GENERAL DESCRIPTION

The chop-check pumps are primarily designed for the pumping of

heavy viscous material with or without  brous content. The models

can be used with a gravity feed single post lift as a topper type

assembly or with a two post lift as a force feed type assembly. The

lower pump is designed for easy priming and the double acting

feature is standard in all ARO industrial pumps. Material is delivered

to the pump discharge outlet on both the up and down stroke.

The motor is connected to the lower pump end by a spacer section.

This allows for lubrication of the upper packing gland and prevents

motor contamination because of normal wear and eventual leak-

age through the material packing gland. Be sure the solvent cup is

adequately  lled with lubricant to protect the upper packings and

insure longest service life.

WARNING

HAZARDOUS PRESSURE. Do not exceed maxi-

mum operating pressure of 2250 p.s.i. (155.2 bar) at 90 p.s.i.

(6.2 bar) inlet air pressure.

Pump Ratio X = Maximum Pump

Inlet Pressure to Pump Motor Fluid Pressure

Pump ratio is an expression of the relationship between the pump motor area

and the lower pump end area. EXAMPLE: When 150 p.s.i. (10.3 bar) inlet pressure

is supplied to the motor of a 4:1 ratio pump, it will develop a maximum of 600

p.s.i. (41.4 bar)  uid pressure (at no  ow) - as the  uid control is opened, the  ow

rate will increase as the motor cycle rate increases to keep up with the demand.

WARNING

Refer to general information sheet for additional

safety precautions and important information.

NOTICE: Thermal expansion can occur when the  uid in the mate-

rial lines is exposed to elevated temperatures. Example: Material

lines located in a non-insulated roof area can warm due to sunlight.

Install a pressure relief valve in the pumping system.

Replacement warning label (pn 92325) is available upon re-

quest.

TROUBLE SHOOTING

Pump problems can occur in either the air motor section or the

lower pump end section. Use these basic guidelines to help deter-

mine which section is a ected.

Pump will not cycle.

Be certain to first check for non-pump problems including

kinked, restrictive or plugged inlet / outlet hose or dispensing

device. Depressurize the pump system and clean out any ob-

structions in the inlet / outlet material lines.

Refer to the motor manual for trouble shooting if the pump

does not cycle and / or air leaks from the air motor.

Damaged motor. Service the motor.

Pump cycles but does not deliver material.

Refer to the lower pump end manual for further trouble shoot-

ing.

y

y

y

y

PUMP CONNECTION - UPPER / LOWER

NOTE: All threads are right hand.

Lay the pump assembly on a work bench.

Remove the three (Y6-128-C) cap screws and (Y14-750-K) lock

washers from the three spacer rods (see  gure 1).

Pull the air motor from the lower pump end until the motor

piston rod is in the “down” position and the lower pump end

rod is in the “up” position.

Remove the three spacer rods by removing the three (Y6-128-C)

cap screws and (Y14-750-K) lock washers.

Using e-ring pliers, slide the “e” ring up far enough to allow the

sleeve to move upward and release the two connectors (see

 gure 2).

PUMP CONNECTION DETAIL

Pump Motor Piston Rod

95069 “E” Ring

Lower Pump Piston Rod

94688 Connector (2)

94689 Sleeve

Figure 2

REASSEMBLY

Align the pump motor with the lower pump end. Position the

air inlet of the motor 180° from the material outlet.

Install the two connectors (94688) and retain with the sleeve

(94689). Slide the “e” ring (95069) back into position.

Assemble the three spacer rods (93866) to the lower pump and

secure using three (Y14-750-K) lock washers and (Y6-128-C)

cap screws.

Reinstall the spacer rods to the pump motor.

Bring the motor and lower pump together and retain with

three (Y14-750-K) lock washers and (Y6-128-C) cap screws.

1.

2.

3.

4.

5.

1.

2.

3.

4.

5

.

PUMP OPTION DESCRIPTION CHART

Packing Material

Spring Arrangement

Plunger Type

PACKING MATERIAL

(Packings are upper and lower unless noted)

3 - Glass  lled PTFE J - Polyurethane (upper)

C - UHMW-PE UHMW-PE (lower)

F - UHMW-PE / Leather staggered (upper) P - UHMW-PE / Glass  lled PTFE staggered (upper)

UHMW-PE (lower) UHMW-PE (lower)

R - Glass  lled PTFE / UHMW-PE staggered (upper)

Glass  lled PTFE (lower)

SPRING ARRANGEMENT PLUNGER TYPE

3 - No spring E - Carbon steel with hard chrome plating

4 - Multiple wave spring

8 - No spring with alternate solvent cup

9 - Multiple wave spring with alternate solvent cup

y

ARO® is a registered trademark of Ingersoll Rand

y

1
2

Ingersoll-Rand 650875-XXX-C User manual

Brand: Ingersoll-Rand

Model: 650875-XXX-C

Type: User manual

This manual is also suitable for

Heat Pump 650875-XXX-C

Download PDF

Related papers

Other documents