GE AKCQ08ACA Owner's manual

Write the model and serial

numbers here:

Model # _________________

Serial # _________________

You can find the rating label on the

side of the air conditioner.

GE is a trademark of the General Electric Company. Manufactured under trademark license.

OWNER’S MANUAL

AIR CONDITIONER

ROOM

49-7845 Rev. 0 08-18 GEA

SAFETY INFORMATION .........3

USING THE AIR CONDITIONER

Controls ..............................4

Starting the Air Conditioner .............5

Using the Remote Control ..............6

Air Direction ..........................7

CARE AND CLEANING

Grille and Case ........................7

Air Filter ..............................7

Annual Maintenance ....................7

INSTALLATION INSTRUCTIONS

Before You Begin ......................8

Electrical Requirements ................8

Tools You will Need ....................8

Installation Requirements ...............8

Parts Included .........................9

Installing the Air Conditioner ...........10

TROUBLESHOOTING

Normal Operating Sounds ............. 11

Troubleshooting Tips ..................12

LIMITED WARRANTY ...........13

CONSUMER SUPPORT ..........14

AKCQ08ACA

AKCQ10ACA

AKCQ10DCA

AKCQ12ACA

AKCQ12DCA

ENGLISH/FRANÇAIS/

ESPAÑOL

2 49-7845 Rev. 0

THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.

Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.

We take pride in the craftsmanship, innovation and design that goes into every GE Appliances

product, and we think you will too. Among other things, registration of your appliance ensures that we

can deliver important product information and warranty details when you need them.

Register your GE appliance now online. Helpful websites and phone numbers are available in the

Consumer Support section of this Owner’s Manual.

49-7845 Rev. 0 3

SAFETY INFORMATION

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

For your safety, the information in this manual must be followed to minimize the risk of

fire, electric shock or personal injury.

■ Use this appliance only for its intended purpose as

described in this Owner’s Manual.

■ This air conditioner must be properly installed in accordance

with the Installation Instructions before it is used.

■ Never unplug your air conditioner by pulling on the

power cord. Always grip plug firmly and pull straight

out from the receptacle.

■ Replace immediately all electric service cords that

have become frayed or otherwise damaged. A

damaged power supply cord must be replaced with a

new power supply cord obtained from the manufacturer

and not repaired. Do not use a cord that shows cracks

or abrasion damage along its length or at either the

plug or connector end.

■ Turn the unit OFF and unplug your air conditioner

before cleaning.

■ To avoid risk of injury or property damage, the air

conditioner should only be serviced by a qualified

servicer, who should hold a current valid certificate

from an industry-accedited assessment authority,

which authorizes their competence to handle

refrigerants safely in accordance with an industry

recognized assessment specification.

■ For your safety…do not store or use combustible

materials, gasoline or other flammable vapors or

liquids in the vicinity of this or any other appliance.

■ All air conditioners contain refrigerants, which under federal

law must be removed prior to product disposal. If you are

getting rid of an old product with refrigerants, check with

the company handling disposal about what to do.

■ If the receptacle does not match the plug, the receptacle

must be changed out by a qualified electrician.

■ These R410A air conditioning systems require

contractors and technicians to use tools, equipment

and safety standards approved for use with this

refrigerant. DO NOT use equipment certified for R22

refrigerant only.

WARNING

USE OF EXTENSION CORDS

RISK OF FIRE. Could cause serious injury or death.

■ DO NOT use an extension cord with this Built-In Air

Conditioner.

■ DO NOT use surge protectors or multi-outlet adaptors

with this Built-In Air Conditioner.

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third

(ground) prong from the power cord. For personal safety,

this appliance must be properly grounded.

DO NOT use an adapter plug with this appliance.

The power cord of this appliance is equipped with a

3-prong (grounding) plug which mates with a standard

3-prong (grounding) wall outlet to minimize the possibility

of electric shock hazard from this appliance.

Power cord includes a current interrupter device. A test

and reset button is provided on the plug case. The device

should be tested on a periodic basis by first pressing the

TEST button and then the RESET button while plugged

into the outlet. If the TEST button does not trip or if the

RESET button will not stay engaged, discontinue use of the

air conditioner and contact a qualified service technician.

Have the wall outlet and circuit checked by a qualified

electrician to make sure the outlet is properly grounded.

Where a 2-prong wall outlet is encountered, it is your

personal responsibility and obligation to have it replaced

with a properly grounded 3-prong wall outlet.

The air conditioner should always be plugged into its

own individual electrical outlet which has a voltage rating

that matches the rating plate.

This provides the best performance and also prevents

overloading house wiring circuits which could cause a

fire hazard from overheated wires.

See the Installation Instructions, Electrical

Requirements section for specific electrical connection

requirements.

WARNING

Chemical Burn Hazard. Keep batteries away from children.

■ This product contains a lithium button/coin cell battery.

If a new or used lithium button/coin cell battery is

swallowed or enters the body, it can cause severe

internal burns and can lead to death in as little

as 2 hours. Always completely secure the battery

compartment. If the battery compartment does not

close securely, stop using the product, remove the

batteries, and keep it away from children.

■ If you think batteries might have been swallowed or

placed inside any part of the body, seek immediate

medical attention.

■ The cells shall be disposed of properly, including

keeping them away from children.

■

Even used cells may cause injury.

READ AND SAVE THESE INSTRUCTIONS

4 49-7845 Rev. 0

USING THE AIR CONDITIONER

Controls

1. Power Pad

Turns air conditioner on and off. When turned on,

the display will show the room temperature.

2. Display

Shows the room temperature or time remaining on

the Delay timer. Shows the Set temperature while

setting the temperature in Cool or Eco modes.

3. Temp and Delay Increase + /Decrease – Pads

Use to set temperature or delay time. Temperature

can be set in Cool and Eco mode.

4. Mode Pad

Use to set the air conditioner to Fan, Energy Save,

Cool or Dehum mode.

5. Fan Speed Pad

Use to set the fan speed to High, Med, or Low

on the unit.

6. Timer

Use to set the air conditioner to turn on or off

automatically.

7. Filter Reset Pad

This feature automatically notifies you that the air

filter must be cleaned.

Features and appearance will vary.

Lights below the touch pads on the air conditioner control panel indicate the selected settings.

Unit power

on/off

Mode select

Fan speed

Delay 1–24hr

Temperature

set/Delay

Timer Increase

and Decrease

Air Conditioner Controls Remote Control

1

2 34 5

6

7

ON/OFF

MODE

SPEED

DELAY

TEMP/TIME

49-7845 Rev. 0 5

Operating your air conditioner properly helps you to obtain

the best possible results. This section explains how to

operate this air conditioner.

IMPORTANT:

• When you turn off the air conditioner , either at the control

panel or with the remote control, wait at least 3 minutes

before turning it back on. This prevents the compressor

from overloading. This 3 minute delay also applies when

switching from cool mode to fan and back.

• Do not operate your air conditioner in the Cool mode

when the outside temperature is below 61°F (16° C).

The inside evaporator coil will freeze up, and the air

conditioner will not operate properly.

Using the Air Conditioner

USING THE AIR CONDITIONER

Starting the Air Conditioner

1. Carefully remove the clear plastic film from the control

panel.

2. Press POWER once to turn on the air conditioner.

NOTE: When the air conditioner is first plugged in, the

LED display will show “88” for 3 seconds.

After the air conditioner is turned on for the first time,

the display will show the temperature 72 F and the

fan is automatically set to Low speed and the Mode

indicator will show ECO.

NOTE: To switch the temperature display between

Fahrenheit (F) and Celsius(C), the air conditioner

must be plugged in, and turned ON. On the control

panel on the front of the AC, press the UP and DOWN

button at the same time and hold for 3 seconds. The

change cannot be done using the remote control.

3. Select Mode. Refer to “Mode.”

4. Select Speed. Refer to “Speed.”

5. Set Timer. Refer to “Temp/Time.”

6. Reset the filter. Refer to “Filter Reset.”

MODE

1. Press mode until you see the indicator light come on

next to the desired setting.

2. Choose Fan, Eco, Cool, or Dehum.

FAN - Only the fan runs. Press SPEED to select High,

Med or Low fan speed. The display shows the current

room temperature.

ECO - In this mode the fan runs only when cooling

is needed. The fan will run for 3 minutes after the

compressor shuts off. The fan then cycles on for 2

minutes at 10 minute intervals until the temperature

in the room is above the set temperature. The

compressor then turns back on.

COOL - Cools the room. Press SPEED to select High,

Med, Low Fan speed. Press the TEMP/TIME up or

down arrow button to adjust the temperature.

DEHUM - Aids in removing humidity from the room.

This setting will NOT cool the room. NOTE: Dehum

mode cannot be used to cool the room.

SPEED

1. Press FAN SPEED until you see the indicator light

come on next to the desired setting.

2. Choose High, Med, Low

HIGH - For maximum cooling

MED - For normal cooling

LOW - For minimum cooling

TIMER

To set the air conditioner to turn off between 1 hour and

24 hours (The air conditioner must be ON to set):

1. Press TIMER. Timer Off indicator light will be on. The

display will show the remaining hours before the air

conditioner will turn off.

2. Press the TEMP/TIME up or down arrow button to

change the delay time from 1 hour to 24 hours.

3. After 5 seconds, Timer Off indicator light will remain

on. The display will show the remaining time to Timer

Off.

To set the air conditioner to turn on between 1 hour and

24 hours:

1. Press TIMER. Timer On indicator light will be on. The

display will show the remaining hours before the air

conditioner will turn on.

2. Press the TEMP/TIME up or down arrow button to

change the delay time from 1 hour to 24 hours.

3. After 5 seconds, Timer On indicator light will remain

on. The display will show the remaining time to Timer

On.

To clear timer program:

NOTE: Air conditioner can be either on or off.

Press TIMER until Timer indicator light turns off.

To view or change the remaining time (in hours):

TIMER OFF

1. Press the TEMP/TIME up or down arrow button to

increase or decrease the time.

2. After 5 seconds, the display will show the remaining

time to Timer OFF.

TIMER ON

1. The display will show the remaining time.

2. Press the TEMP/TIME up or down arrow button to

increase or decrease the time.

3. After 5 seconds, the display will show the remaining

time to Timer ON.

6 49-7845 Rev. 0

Using the Air Conditioner

Starting the Air Conditioner (Cont.)

TEMP/TIME

1. Press the TEMP/TIME up arrow button to raise the

temperature. Each time you press the TEMP/TIME up

arrow button, the temperature will go up 1°F until it

reaches 86°F (30°C).

2. Press the TEMP/TIME down arrow button to lower the

temperature. Each time you press the TEMP/TIME

down arrow button, the temperature will go down 1°F

until it reaches 61°F (16°C).

NOTE: After 5 seconds, under Fan mode, the display

will show the current temperature. Under Cool, Eco or

Dehum mode, the display will show the set temperature.

FILTER RESET

This feature automatically notifies you that the air filter

must be cleaned. The indicator light will come on after

240 hours of operation. Clean the air filter (refer to Care

and Cleaning), place it back in the front panel, and press

the Filter Reset button. The light will turn off.

USING THE AIR CONDITIONER

Using the Remote Control

NOTE: The raised dots are Braille for the

visually impaired.

Remote control may differ in appearance

from the image shown.

NOTE: Remove and discard protective film

prior to use. The remote control runs on

one CR2025 battery (included). Replace

battery after 6 months of use, or when the

remote control starts to lose power. To

change battery, remove screw on back

panel of remote to remove cover.

POWER

Press ON/OFF to turn on the air

conditioner.

Mode

Press MODE to choose Fan, Eco, Cool or Dehum.

Speed

Press SPEED to choose High, Med, Low.

TIMER

To set the air conditioner to turn off after a set amount

between 1 hour and 24 hours (unit must be ON):

1. Press TIMER. Timer OFF indicator light on the air

conditioner control panel will be on.

2. Press the TEMP/TIME up or down arrow button to

change the delay time from 1 hour to 24 hours.

3. After 5 seconds, Timer OFF indicator light on the air

conditioner control panel will remain on.

TO SET THE AIR CONDITIONER TO TURN ON

BETWEEN 1 HOUR AND 24 HOURS:

1. Press TIMER. Timer On indicator light on the air

conditioner control panel will be on.

2. Press the TEMP/TIME up or down arrow button to

change the delay time from 1 hour to 24 hours.

3. After 5 seconds, Timer On indicator light on the air

conditioner control panel will remain on.

TO CLEAR TIMER PROGRAM:

NOTE: Air conditioner can be either on or off.

Press TIMER until Timer indicator light turns off.

TO VIEW OR CHANGE THE REMAINING TIME (IN

HOURS):

TIMER OFF

1. Press the TEMP/TIME up or down arrow button to

increase or decrease the time.

2. After 5 seconds, the display will show the remaining

time to Timer OFF.

TIMER ON

1. The display will show the remaining time.

2. Press the TEMP/TIME up or down arrow button to

increase or decrease the time.

TEMP/TIME

1. Press the TEMP/TIME up arrow button to raise the

temperature. Each time you press the TEMP/TIME up

arrow button, the temperature will go up 1°F until it

reaches 86°F (30°C).

2. Press the TEMP/TIME down arrow button to lower the

temperature. Each time you press the TEMP/TIME

down arrow button, the temperature will go down 1°F

until it reaches 61°F (16°C).

ON/OFF

MODE

SPEED

DELAY

TEMP/TIME

49-7845 Rev. 0 7

USING THE AIR CONDITIONER / CARE AND CLEANING

Using the Air Conditioner

Air Direction

Use the lever to adjust the air direction left, right, up and

down.

Care and Cleaning

Grille and Case

Turn the air conditioner off and remove the plug from the

wall outlet before cleaning.

To clean, use water and a mild detergent. Do not use

bleach or abrasives.

Annual Maintenance

Your air conditioner needs annual maintenance to help

ensure steady, top performance throughout the year.

Call your local authorized dealer to schedule an annual

checkup. The expense of an annual inspection is your

responsibility.

Air Filter

The air filter behind the front grille should be checked

and cleaned at least every 2 weeks or more often if

necessary.

CAUTION

DO NOT operate the air conditioner

without a filter because dirt and lint will clog it and

reduce performance.

Cleaning the Air Filter

1. Turn off the air conditioner.

2. Remove the air filter by pulling the front panel to open

and removing the air filter.

3. Use a vacuum cleaner to clean air filter. If the air

filter is very dirty, wash it in warm water with a mild

detergent. Do not wash the air filter in the dishwasher

or use any chemical cleaners. Air dry the air filter

completely before replacing to ensure maximum

efficiency.

4. Replace the air filter.

5. Close the front panel.

6. Turn on the air conditioner.

Cleaning the Front Panel

1. Turn off the air conditioner.

2. Clean the front panel with a soft, damp cloth.

3. Air dry the front panel completely.

4. Turn on the air conditioner.

Air Filter

Front Panel

8 49-7845 Rev. 0

Installation Instructions

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT – Save these

instructions for local inspector’s use.

•

IMPORTANT – Observe all governing

codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions for

future reference.

• Skill level – Installation of this appliance requires

basic mechanical skills.

• Completion time – Approximately 1 hour

• We recommend that two people install this product.

• Proper installation is the responsibility of the

installer.

• Product failure due to improper installation is not

covered under the Warranty.

• You MUST use all supplied parts and use proper

installation procedures as described in these

instructions when installing this air conditioner.

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com

ELECTRICAL REQUIREMENTS

These models require a 115/120-volt AC or a

230-volt AC, 60-Hz grounded outlet protected

with a 15-amp time-delay fuse or circuit

breaker.

The 3-prong grounding plug minimizes the possibility

of electric shock hazard. If the wall outlet you plan to

use is only a 2-prong outlet, it is your responsibility to

have it replaced with a properly grounded 3-prong wall

outlet.

Power cord includes a current interrupter device. A

test and reset button is provided on the plug case. The

device should be tested on a periodic basis by first

pressing the TEST button and then the RESET button

while plugged into the outlet. If the TEST button does

not trip or if the RESET button will not stay engaged,

discontinue use of the air conditioner and contact a

qualified service technician.

INSTALLATION REQUIREMENTS

For new construction, install the Haier Wall Sleeve

HTTWSB.

Remove old air conditioner and inspect sleeve for

the following:

Installation - Make sure that sleeve is securely

installed and in sound structural condition.

Dimensions - Measure the size to make sure the air

conditioner will fit.

Slope - Ensure wall sleeve is level or has a rearward

slope for condensate to drain from the unit.

If pre-existing wall sleeve is suspect, it is

recommended to install Haier Wall Sleeve, model

HTTWSB, in its place.

TOOLS YOU WILL NEED

Phillips head screwdriver

Ruler or tape measure

Pencil

Level

Scissors or knife

Drill and 1/8” drill bit

CAUTION

Do not, under any circumstances, cut or remove

the third (ground) prong from the power cord.

Do not change the plug on the power cord of this

air conditioner.

Aluminum house wiring may present special

problems—consult a qualified electrician.

CAUTION

There are sharp edges that can cause serious cuts.

When lifting the air conditioner, it is HEAVY. Use 2

peoples to lift.

INSTALLATION INSTRUCTIONS

REAR

Wall Sleeve

UNIT

LEVEL

FRONT

to

ARRIÈRE

Compartiment mural

APPAREIL

NIVEAU

AVANT

1/4 po à 5/16 po

PARTE

TRASERA

Forro para pared

UNIDAD

NIVEL

PARTE

FRONTAL

a

49-7845 Rev. 0 9

INSTALLATION INSTRUCTIONS

Installation Instructions

Check the contents of the accessories supplied with your air conditioner as shown below:

7

5

10

2

1

3

4

6

8

9

Number Part name QTY.

1 Wide Top/Bottom Trim Frame 2

2 Wide Side Trim Frame 2

3 Narrow Top/Bottom Trim Frame 2

4 Narrow Side Trim Frame 2

5 Foam Seal 1

6 Universal Fit Rear Grille 1

7 Rubber Clamp 4

8 Tapered Spacer Block 2

9 Board 1

10 Retaining Bracket 1

10 49-7845 Rev. 0

Installing the Air Conditioner

1. Identify the existing wall sleeve before installing

the unit from the list below:

NOTE: All wall sleeves used to mount the new Air

Conditioner must be in sound structural condition

and have a rear grille that securely attaches to

sleeve,or rear flange that serves as a stop for the

Air conditioner.

2. Clean the interior of the sleeve (do not disturb

seals).

3. Repaint the sleeve if needed.

4. For best performance and energy efficiency,

replace the existing rear louver grille with the

plastic mesh supplied in the package. Measure

and cut the plastic grille to fit and place inside

the wall sleeve against the rear flange.

Installing the Air Conditioner (Cont.)

If your existing sleeve has a rear grille and you

wish to retain: redirect the louvers to 60 angle

as shown below.

5. If the depth of your existing wall sleeve is less

than or equal to 20”,skip to step 7. Otherwise,

cut the baffles and the support blocks according

to length “A” in the table below.

6. Remove the backing from the support blocks

and attach them to the inside of the wall sleeve

as shown below. Slide the baffle into slots of the

support blocks.

7. Install unit into the wall sleeve, leaving enough

of the unit exposed to access bracket location.

8. Install retaining bracket at front left corner by

removing and reusing screw. Push unit fully into

sleeve

Brand

Wall Sleeve Dimensions

Width Height Depth

Haier Amana 25-13/32” 15-3/4” 17-1/2”

Haier Amana 25-7/8” 15-9/16” 16-3/4”

White-

Westinghouse

Frigidare Carrier

(52F series)

25-1/2” 15-1/4” 16, 17-1/2”

or 22

GE Appliances/

Hotpoint

26” 15-5/8” 16-7/8”

Whirlpool 25-7/8” 16-1/2” 17-1/8”

Sears/Kenmore 25-7/8” 15-17/32” 16-23/32”

Carrier (51S

series)

25-3/4” 16-7/8” 18-5/8”

LG 25-7/8” 15-17/32” 16-23/32”

Plastic

Clamp

Plastic

Clamp

Plastic

Clamp

Plastic

Clamp

Serrage

En Caoutchouc

Serrage

En Caoutchouc

Serrage

En Caoutchouc

Serrage

En Caoutchouc

Abrazadera

de Goma

Abrazadera

de Goma

Abrazadera

de Goma

Abrazadera

de Goma

Pales arrieres

Rejillas traseras

Vista desde arriba

A

Depth “D” of the

existing wall sleeve

(inches)

Length “A”

(inches)

20 < D ≤ 20-5/8” 3/4

20-5/8 < D ≤ 21-3/4 1-3/4

21-3/4 < D ≤ 24 4

Tapered Spacer

Block Board

FRONT

Wall

Sleeve

Wall

Tapered Spacer

Block

6

1

2

”

Plaque de bloc

d'espacement

en biseau

AVANT

Compartiment

Mural

Bloc d'espacement

en biseau

6

1

2

po

Tablilla del bloque

espaciador cónico

FRONTAL

Forro aislante

pared

Pared

Bloque espaciador

cónico

6

1

2

”

Installation Instructions

INSTALLATION INSTRUCTIONS

Retaining

Bracket

Screw

49-7845 Rev. 0 11

Installing the Air Conditioner (Cont.)

9. Install the 1” x 1-1/2” x 84” long stuffer seal

between the wall sleeve and the unit.

10. To assemble trim, snap the tab of each piece

into the slot of the other piece as shown below.

Two different trim frames are supplied with unit.

Use the trim frame that best fits your sleeve.

Slide trim over the front of the air conditioner

until trim is flush with sleeve as shown below.

NOTE: Be sure to route the cord through the trim

frame before placing the trim frame on the unit. Do

not trap the cord between the trim frame and the

wall.

Installation Instructions

Assemble Trim

Ensamblar moldura

Assembler la garniture

Normal Operating Sounds

When your air conditioner is operating normally, you may hear sounds such as:

■ Droplets of water hitting the condenser, causing a pinging or clicking sound. The water droplets help cool the

condenser.

■ Air movement from the fan.

■ Clicks from the thermostat cycle.

■ Vibrations or noise due to poor wall or window construction.

■ A high-pitched hum or pulsating noise caused by the modern high-efficiency compressor cycling on and off.

INSTALLATION INSTRUCTIONS / TROUBLESHOOTING

12 49-7845 Rev. 0

Troubleshooting Tips... Before you call for service

Save time and money! Review the charts on the following pages first and you may not need to call for service.

Problem Possible Cause What To Do

Air conditioner

does not operate.

The unit is unplugged. Plug into a grounded 3 prong outlet. See “Electrical

Requirements.”

The power supply cord has tripped

(Reset button has popped out).

Press and release RESET (listen for click; Reset button will latch and

on some devices, a green light will turn on) to resume operation.

A household fuse has blown, or circuit

breaker has tripped.

Replace the fuse or reset the circuit breaker. If the problem

continues, call an electrician. See “Electrical Requirements.”

The Power button has not been pressed

or the Mode control knob is turned to Off.

Press POWER or turn the Mode control knob to an active

setting.

The local power has failed. Wait for power to be restored.

Air conditioner

blows fuses

or trips circuit

breakers

Too many appliances are being used on

the same circuit.

Unplug or relocate appliances that share the same circuit.

Time-delay fuse or circuit breaker of the

wrong capacity is being used.

Replace with a time-delay fuse or circuit breaker of the correct

capacity. See “Electrical Requirements.”

An extension cord is being used. Do not use an extension cord with this or any other appliance.

You are trying to restart the air

conditioner too soon after turning off the

air conditioner.

Wait at least 3 minutes after turning off the air conditioner before

trying to restart the air conditioner.

Air conditioner

power supply cord

trips (Reset button

pops out)

Disturbances in your electrical current

can trip (Reset button will pop out) the

power supply cord.

Press and release RESET (listen for click; Reset button will

latch and on some devices, a green light will turn on) to resume

operation.

Electrical overloading, overheating, cord

pinching or aging can trip (Reset button

will pop out) the power supply cord.

After correcting the problem, press and release RESET (listen

for click; Reset button will latch and on some devices, a green

light will turn on) to resume operation.

NOTE: A damaged power supply cord must be replaced with a

new power supply cord obtained from the product manufacturer

and must not be repaired.

Air conditioner

seems to run too

much

The current air conditioner replaced an

older model.

The use of more efficient components may cause the air

conditioner to run longer than an older model, but the total

energy consumption will be less. Newer air conditioners do not

emit the “blast” of cold air you may be accustomed to from older

air conditioners, but this is not an indication of lesser cooling

capacity or efficiency. Refer to the efficiency rating (EER) and

capacity rating (in Btu/h) marked on the air conditioner.

The air conditioner is in a heavily

occupied room, or heat-producing

appliances are in use in the room.

Use exhaust vent fans while cooking or bathing and try not to

use heatproducing appliances during the hottest part of the day.

A higher capacity air conditioner may be required, depending on

the size of the room being cooled.

Air conditioner

cycles on and off

too much or does

not cool room in

cooling mode

The air conditioner is not properly sized

for your room.

Check the cooling capabilities of your room air conditioner.

Room air conditioners are not designed to cool multiple rooms.

The filter is dirty or obstructed by debris.

Clean the filter.

There is excessive heat or moisture

(open container cooking, showers, etc.)

in the room.

Use a fan to exhaust heat or moisture from the room. Try not to

use heat-producing appliances during the hottest part of the day.

The louvers are blocked. Install the air conditioner in a location where the louvers are free

from curtains, blinds, furniture, etc.

The outside temperature is below 65°F

(18°C).

Do not try to operate your air conditioner in the cooling mode

when the outside temperature is below 65°F (18°C).

The temperature of the room you are

trying to cool is extremely hot.

Allow extra time for the air conditioner to cool off a very hot

room.

Windows or doors to the outside are open.

Close all windows and doors.

The Temperature control is not at a cool

enough setting.

Adjust the TEMP/TIME control to a cooler setting by pressing

the minus button to reduce the temperature. Set the Fan Speed

control to the highest setting.

Water drips from

cabinet into your

house

The air conditioner is not properly

leveled.

The air conditioner should slope slightly downward toward

the outside. Level the air conditioner to provide a downward

slope toward the outside to ensure proper drainage. See the

Installation Instructions.

NOTE: Do not drill a hole into the bottom of the metal base and

condensate pan.

TROUBLESHOOTING

49-7845 Rev. 0 13

LIMITED WARRANTY

GE Appliances Air Conditioner Limited Warranty

■ Service trips to your home to teach you how to use

the product.

■ Improper installation, delivery or maintenance. If you

have an installation problem, or if the air conditioner

is of improper cooling capacity for the intended use,

contact your dealer or installer. You are responsible

for providing adequate electrical connecting facilities.

■ Failure of the product resulting from modifications

to the product or due to unreasonable use including

failure to provide reasonable and necessary

maintenance.

■ In commercial locations, labor necessary to move the

unit to a location where it is accessible for service by

an individual technician.

■ Replacement of house fuses or resetting of circuit

breakers.

■ Failure due to corrosion on models not corrosion-

protected.

■ Damage to the product caused by improper power

supply voltage, accident, fire, floods or acts of God.

■ Incidental or consequential damage caused by

possible defects with this air conditioner.

■ Damage caused after delivery.

What GE Appliances Will Not Cover:

This limited warranty is extended to the original purchaser and any succeeding owner for products purchased

for home use within the USA. If the product is located in an area where service by a GE Appliances Authorized

Servicer is not available, you may be responsible for a trip charge or you may be required to bring the product to an

Authorized GE Service location for service. In Alaska, the limited warranty excludes the cost of shipping or service

calls to your home.

Some states do not allow the exclusion or limitation of incidental or consequential damages. This limited warranty

gives you specific legal rights, and you may also have other rights which vary from state to state. To know what your

legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.

Warrantor: GE Appliances, a Haier company

Louisville, KY 40225

All warranty service must be provided by our Factory Service Centers, or an authorized Customer Care

®

technician.

To schedule service, visit us on-line at GEAppliances.com/service, or call 800.GE.CARES (800.432.2737). Have

serial number and model number available when calling for service.

EXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive remedy is product repair as provided in this

Limited Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a

particular purpose, are limited to two years or the shortest period allowed by law.

For The Period Of: GE Appliances Will Replace:

Two Years

From the date of the

original purchase

Any part of the air conditioner which fails due to a defect in materials or workmanship.

During this limited two-year warranty, GE Appliances will also provide, free of charge, all

labor and related service to replace the defective part.

Staple your receipt here. Proof of the original purchase

date is needed to obtain service under the warranty.

14 49-7845 Rev. 0

Printed in China

Consumer Support

CONSUMER SUPPORT

GE Appliances Website

Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day, any day

of the year! You can also shop for more great GE Appliances products and take advantage of all our on-line support

services designed for your convenience. In the US: GEAppliances.com

Register Your Appliance

Register your new appliance on-line at your convenience! Timely product registration will allow for enhanced

communication and prompt service under the terms of your warranty, should the need arise. You may also mail in

the pre-printed registration card included in the packing material. In the US: GEAppliances.com/register

Schedule Service

Expert GE Appliances repair service is only one step away from your door. Get on-line and schedule your service at

your convenience any day of the year. In the US: GEAppliances.com/service or call 800.432.2737 during normal

business hours.

Extended Warranties

Purchase a GE Appliances extended warranty and learn about special discounts that are available while your

warranty is still in effect. You can purchase it on-line anytime. GE Appliances Services will still be there after your

warranty expires. In the US: GEAppliances.com/extended-warranty or call 800.626.2224 during normal

business hours.

Remote Connectivity

For assistance with wireless network connectivity (for models with remote enable),

visit our website at GEAppliances.com/connected-home-smart-appliances or call 800.220.6899 in the US.

Parts and Accessories

Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes

(VISA, MasterCard and Discover cards are accepted). Order on-line today 24 hours every day.

In the US: GEApplianceparts.com or by phone at 877.959.8688 during normal business hours.

Instructions contained in this manual cover procedures to be performed by any user. Other servicing

generally should be referred to qualified service personnel. Caution must be exercised, since improper

servicing may cause unsafe operation.

Contact Us

If you are not satisfied with the service you receive from GE Appliances, contact us on our Website with all the

details including your phone number, or write to:

General Manager, Customer Relations | GE Appliances, Appliance Park | Louisville, KY 40225

GEAppliances.com/contact

Page is loading ...

49-7845 Rev. 0 9

INSTRUCCIONES DE INSTALACIÓN

Instrucciones de instalación

Número Nombre de la parte CANT.

1 Moldura ancha uperior/inferior 2

2 Moldura ancha lateral 2

3 Moldura estrecha superior/inferior 2

4 Moldura estrecha lateral 2

5 Cinta de espuma 1

6 Rejilla posterior de ajuste universal 1

7 Abrazadera De Goma 4

8 Bloque espaciador cónico 2

9 Placa 1

10 Soporte de Retención 1

7

5

10

2

1

3

4

6

8

9

Page is loading ...

GE AKCQ08ACA Owner's manual

GE AKCQ08ACA Owner's manual

in other languages

Other documents