Grizzly T1238 Owner's manual

Brand: Grizzly

Model: T1238

Type: Owner's manual

For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com

MODEL T1238

MOBILE TOOL TABLE

INSTRUCTIONS

For Models Mfd. Since 10/17

NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#TKAB19421 PRINTED IN CHINA

V1.07.18

H. Linkage Bar/Pedal ...................................... 1

I. Caster ......................................................... 1

J. Upper Braces (Front & Back) ..................... 2

K. Pedal Assembly .......................................... 1

L. Wheel Assembly ......................................... 1

M. Handle ........................................................ 1

N. Hardware Bag (Not Shown)

—Carriage Bolts M8-1.25 x 12 ................. 30

—Button Hd Cap Screws M8-1.25 x 16 ... 12

—Flat Head Screws M8-1.25 x 25 ............. 4

—Hex Bolts M8-1.25 x 20 .......................... 2

—Hex Bolt M8-1.25 x 70 ............................ 1

—Flange Nuts M8-1.25 ............................ 38

—Lock Nuts M8-1.25 .................................. 3

—Extension Spring .................................... 1

Introduction

The Model T1238 Mobile Tool Table is designed

to provide a stable, mobile platform for mounting

machinery and equipment.

Figure 1. Model T1238 Mobile Tool Table.

Specifications

• Footprint (Length x Width) ..............20" x 23"

• Height ......................................................30"

• Maximum Weight Capacity ............. 300 lbs.

• Approximate Assembly Time .......30 Minutes

Needed for Assembly

• Open-End Wrenches or Sockets 13mm ..... 2

• Hex Wrench 5mm ....................................... 1

Inventory

Description Qty

A. Table Top ................................................... 1

B. Shelf ........................................................... 1

C. Side Panels ................................................ 2

D. Legs w/Foot Pads ....................................... 4

E. Tool Holder ................................................. 1

F. Upper Braces (Left & Right) ....................... 2

G. Lower Braces ............................................. 2

Figure 2. Inventory.

-2-

T1238 Tool Table (Mfd. Since 10/17)

Assembly

This tool table must be fully assembled before it

can be used. Before beginning the assembly pro-

cess, refer to Needed for Assembly and gather

all listed items.

2. Attach wheel assembly to side assembly

A with (4) M8-1.25 x 16 button head cap

screws. Long linkage should point outward

(see Figure 4) with wheels in the down

position.

To assemble tool table:

1. Build side assembly A by attach-

ing (1) front upper brace to (2) legs with

(4) M8-1.25 x 12 carriage bolts and

(4) M8-1.25 flange nuts (see Figure 3). Use

90° square to make sure legs and supports

are perpendicular (see Figure 3).

Figure 4. Wheel assembly orientation.

4. Attach pedal assembly to side assembly B

built in Step 3 with (4) M8-1.25 x 16 button

head cap screws. Ensure pedal points out-

ward (see Figure 5).

3. Repeat Step 1 in a similar manner to build

side assembly B.

Figure 5. Pedal assembly orientation.

5. Attach caster to pedal assembly with (1)

M8-1.25 x 70 hex bolt and (1) M8-1.25 lock

nut (see Figure 6).

Figure 3. Side assembly A built.

x 4

Legs

Degree

Square

x 4

Pedal

Pointing

Outward

x 4

Linkage

Pointing

Outward

Wheel

Down

Upper

Brace

Figure 6. Caster wheel attached to pedal

assembly.

x 1

Pedal

Assembly

Caster

T1238 Tool Table (Mfd. Since 10/17)

-3-

6. Attach (2) upper braces and shelf to side

assembly A with (6) M8-1.25 x 12 car-

riage bolts and (6) M8-1.25 flange nuts

(see Figure 7).

7. Attach (2) lower braces to side assembly A

with (2) M8-1.25 x 16 button head cap screws

and (2) M8-1.25 flange nuts (see Figure 7).

10. Turn table assembly upside down.

11. Loosely attach linkage bar to wheel assem-

bly with (1) M8-1.25 x 20 hex bolt and

(1) M8-1.25 lock nut to allow movement.

Connect extension spring to linkage bar and

wheel assembly (see Figure 9).

12. Loosely attach linkage bar to pedal assem-

bly with (1) M8-1.25 x 20 hex bolt and (1)

M8-1.25 lock nut to allow movement (see

Figure 10).

8. Attach side assembly A to side assembly

B with (6) M8-1.25 x 12 carriage bolts and

(6) M8-1.25 flange nuts (see Figure 8).

9. Attach side assembly B to lower braces with

(2) M8-1.25 x 16 button head cap screws and

(2) M8-1.25 flange nuts, as shown in Figure

Figure 8. Side assembly B attached.

x 2

x 6

Side Assembly A

Side Assembly B

x 6

x 2

Figure 9. Linkage and spring installed.

x 1

Extension Spring

Linkage Bar

Wheel Assembly

Figure 10. Linkage bar attached to pedal

assembly.

x 1

Linkage

Bar

Figure 7. Upper/Lower braces and shelf

attached to side assembly A.

x 2

Side Assembly A

Shelf

x 6

Lower

Brace

Upper

Brace

-4-

T1238 Tool Table (Mfd. Since 10/17)

18. Ensure all fasteners are firmly tightened and

wheel mechanism operates smoothly.

13. Turn table assembly unit upright. Attach bot-

tom of a side panel to table assembly shelf

with (2) M8-1.25 x 12 carriage bolts and

(2) M8-1.25 flange nuts (see Figure 11).

16. Attach tool holder and top of side panel

with (2) M8-1.25 x 12 carriage bolts and

(2) M8-1.25 flange nuts (see Figure 13).

Figure 14. Table top attached.

x 4

17. Attach table top with (4) M8-1.25 x 25 flat

head screws and (4) M8-1.25 flange nuts

(see Figure 14).

Figure 13. Tool holder attached.

x 2

Tool

Holder

Note: Position side panel so end with

long tab faces up.

15. Repeat Step 13 to attach second side panel

to opposite side of table assembly (see

Figure 11).

14. Attach handle and top of side panel

with (4) M8-1.25 x 12 carriage bolts and

(4) M8-1.25 flange nuts (see Figure 12).

Figure 11. Bottom of side panel attached.

Long Tab

Short Tab

Side

Panel

Shelf

Figure 12. Top of side panel and handle

attached.

x 4

Handle

Side

Panel

x 2

Note: The handle goes on the same side

as the pedal assembly.

T1238 Tool Table (Mfd. Since 10/17)

-5-

Moving Tool TableMounting Machines to Table

The Model T1238 Mobile Tool Table is designed

to have machines mounted to it. Mount the

machines to the table top with applicable hard-

ware (not included).

DO NOT mount machines with high centers

of gravity (like table-top drill presses or

mortising machines) on this table. Doing

so could cause the table to tip and fall,

resulting in serious injury or death.

Failure to properly mount machines to

table can cause tipping resulting in injury

property damage.

The strongest mounting option is a "Through

Mount" (see Figure 15) where holes are drilled

all the way through the table, and hex bolts,

washers, and hex nuts are used to secure the

machine in place.

Machine Base

Table Top

Hex

Bolt

Flat Washer

Lock Washer

Hex Nut

Figure 15. Through mount example.

Depress the lifting pedal to raise the table onto

the wheels. Carefully steer the table to the desired

location, then depress the smaller linkage pedal

to lower the unit onto its feet (see Figure 16).

Any abrupt movement could cause the unit

to tip, resulting in serious personal injury

and property damage.

Figure 16. Moving controls.

Lifting

Pedal

Linkage

Pedal

-6-

T1238 Tool Table (Mfd. Since 10/17)

Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here

are available for purchase. Call (800) 523-4777 or visit our online parts store at www.grizzly.com to check for availability.

REF PART # DESCRIPTION REF PART # DESCRIPTION

1 PT1238001 FLAT HD SCR M8-1.25 X 30 18 PT1238018 HANDLE

2 PT1238002 TABLE TOP 19 PT1238019 EXT RETAINING RING 20MM

3 PT1238003 FLANGE NUT M8-1.25 20 PT1238020 FLAT WASHER 20MM

4 PT1238004 CARRIAGE BOLT M8-1.25 X 16 21 PT1238021 LOCK WASHER 20MM

5 PT1238005 STAND LEG 22 PT1238022 SUPPORT FRAME

6 PT1238006 BUTTON HD CAP SCR M8-1.25 X 16 23 PT1238023 REAR ROLLER LEVER

7 PT1238007 FOOT PAD 24 PT1238024 EXTENSION SPRING

8 PT1238008 UPPER BRACE (FRONT & BACK) 25 PT1238025 LINKAGE BAR/PEDAL

9 PT1238009 LOWER BRACE 26 PT1238026 HEX BOLT M8-1.25 X 55

10 PT1238010 TOOL HOLDER 27 PT1238027 RUBBER WHEEL

12 PT1238012 HEX BOLT M8-1.25 X 20 28 PT1238028 CASTER

13 PT1238013 UPPER BRACE (LEFT & RIGHT) 29 PT1238029 HEX BOLT M8-1.25 X 70

14 PT1238014 SIDE PANEL 30 PT1238030 PEDAL ASSEMBLY

16 PT1238016 SHELF 31 PT1238031 EXT RETAINING RING 20MM

17 PT1238017 HANDLE CAP 32 PT1238032 LOCK NUT M8-1.25

BUY PARTS ONLINE AT GRIZZLY.COM !

Scan QR code to visit our Parts Store.

Parts Breakdown & List

T1238 Tool Table (Mfd. Since 10/17)

-7-

300 lb. max weight

capacity. DO NOT

exceed. Stand may tip

or collapse, and

crushing injury may

occur.

Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes

off or becomes unreadable, the owner of this machine MUST replace it in the original location

before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.

REF PART # DESCRIPTION REF PART # DESCRIPTION

40 PT1238040 NOTICE LABEL 43 PT1238043 CAUTION LABEL

41 PT1238041 GRIZZLY INDUSTRIAL LABEL 44 PT1238044 GRIZZLY.COM LABEL

42 PT1238042 QR CODE LABEL 45 PT1238045 TOUCH-UP PAINT, GLOSSY BLACK

Labels & Cosmetics

-8-

T1238 Tool Table (Mfd. Since 10/17)

Grizzly T1238 Owner's manual

Grizzly T1238 Owner's manual

Grizzly T1238 Owner's manual

Related papers

Other documents