DFI EC70A-KU User manual

DFI
Brand
DFI
Model
EC70A-KU
Type
User manual

This manual is also suitable for

DFI EC70A-KU is a compact and versatile system that offers a wide range of features for various industrial applications. With its rugged design, it can withstand harsh environments and operate reliably in industrial settings. The system supports multiple expansion options, including Mini PCIe and M.2 slots, allowing for customization and flexibility. Additionally, the наличието на множество портов ввода/вывода, таких как COM-порты, USB и LAN, обеспечивает различные возможности подключения для периферийных устройств и сетевого оборудования.

DFI EC70A-KU is a compact and versatile system that offers a wide range of features for various industrial applications. With its rugged design, it can withstand harsh environments and operate reliably in industrial settings. The system supports multiple expansion options, including Mini PCIe and M.2 slots, allowing for customization and flexibility. Additionally, the наличието на множество портов ввода/вывода, таких как COM-порты, USB и LAN, обеспечивает различные возможности подключения для периферийных устройств и сетевого оборудования.

1
www.dfi.com
Rear View
Front View
Quick Installation Guide
EC70A-KU
Panel
Notes:
1.2. This port can be in HDMI or DP++.
1.2. The HDMI is a DP++/HDMI combo port but can only transmit HDMI signals (unless wired as
a DP++ port). Please plug in an HDMI cable with the right orientation and alignment to avoid
damage to the connector. You should feel resistance (due to a pin on the right) if the cable is not
inserted correctly.
Angled-corner
Aligning side
(left)
pin
Align this edge with the
left side of the connector
Angled-corner
(up)
•
EC70A-KU System Unit
•
Mounting screws for SATA, Mini PCIe and M.2
•
Extended power switch cable
Package Contents
COM 2
Power Button (green)
COM 6
COM 4
Status LED (blue)
Reset Switch
COM 1
USB 2.0
VGA
HDMI/DP
(1)
HDD LED
(blue)
Antenna hole
USB 3.0
Line-out
LAN 1
LAN 2
COM 3
COM 5
HDMI
(2)
15~36V
SATA drive bay
USB 2.0
Remote Power Switch
2Quick Installation Guide |
Removing the Chassis Cover
2. The system supports one 2.5" SATA drive. Use 4
provided screws to install a SATA HDD or SSD on
the HDD tray. Then slide the HDD tray back into
the drive bay and close the drive bay by installing
the screws. Make sure that the HDD is on top of
the tray when inserting the tray.
1
Mini PCIe
socket
The SATA drive bay can be easily accessed without opening the system. However, the system
does not support hot-swapping hard drives; turn off the system rst.
Use the following procedure to install SATA HDD or SSD to the system:
1. Locate the drive bay on the front panel and open it by uninstalling the screws. Then take
out the HDD tray.
Installing a SATA Drive
Mounting Screws
Mounting Screws
Before working inside your system, observe the following precautions:
1. Make sure the system and all other peripherals connected to it have been powered off.
2. Disconnect all power cords and cables.
3. The 4 mounting screws on the bottom of the system are used to secure the cover to the
chassis. Remove these screws and put them in a safe place for later use.
The Mini PCIe and M.2 sockets are accessible after removing the chassis cover. The M.2 type
2280 socket (B Key) provides PCIe Gen 3.0 x 1 interface that supports both PCIe NVMe and
SATA SSD cards. The full-size Mini PCIe socket supports only mSATA cards.
M.2 socket
HDD tray Screws
SATA data
SATA power
3
Accessing the System Board
The system board is equipped with 2 Mini PCIe slots: one full-size and one half-size slot. The full-
size Mini PCIe slot supports PCIe and USB interfaces whereas the half-size Mini PCIe slot supports
PCIe, USB and SATA interfaces (jumper switchable between PCIe and SATA). The PCIe sockets
are located on the main board; to access the main board, detach the expansion board on top of
it. Remove the screws that afx the front and back bezels as shown in the following pictures to
remove the expansion board from the system.
Use a wrench or a screwdriver
with a socket end to remove the
fasteners used on DB-9 and VGA
connectors
Use a wrench to remove the
hexagonal gasket
Remove these screws to detach the
expansion board from the main board
To install a Mini PCIe or an M.2 card:
1. Grasp the Mini PCIe card by its edges and align the notch of the card with the key in the
connector and insert the bottom edge of the card into the connector.
2. Push down on the other end of the card and use the provided mounting screw to secure the
card on the system board.
Mini PCIe Module
Mini PCIe Socket
Key
Stand-off
Notch
Mini PCIe Module
Mini PCIe Socket
Key
Stand-off
Notch
Mini PCIe Module
Mini PCIe Socket
Key
Stand-off
Notch
4Quick Installation Guide |
COM 1~COM 2:
RS232/422/485
COM 4:
RS232 or DIO
COM 3, 5 & 6:
RS232
DC-in
1
6
1
1
1
3
1
Mini PCIe /mSATA
12
12
1
Reset
Power
Front
Panel
(JP11)
DDR4 DDR4
DDR4
DDR4
COM 4 (RS232/DIO)
LAN 2
LAN 1
USB 2
USB 1
USB 3.0
USB 4
USB 3
COM 3 (RS232)
COM 2 (RS232/422/485)
COM 1 (RS232/422/485)
COM 6 (RS232)
USB 3.0
SPI Flash
BIOS
JP2
JP1
Battery
Mini PCIe
MIC-inLINE-out
HDMI
1
SATA Power
Realtek ALC888
Intel
WGI210AT
JP3
JP4
COM4/DIO Pin Select
COM4/DIO Pin Select
Clear CMOS
Mini PCIe PCIe/
SATA Select
(JP3)
(JP4)
Auto PWR ON
(JP1)
(JP2)
(JP7)
1
SATA 3.0
LED 1
SATA_2
USB 2.0 7/8
1
2
10
1
2
1
2
COM 6 COM 5
DC-in
1
2
79
80
EIO
Board Layout and Jumper Settings
RS232
RS422
RS485
6
7
8
9
1
2 3 4
5
DCD
RXD
TXD
DTR
GND
DSR
RTS
CTS
RI
N.C.
N.C.
N.C.
N.C.
2
4
5
3
1
7
6 8
9
RXD+
RXD-
TXD+
TXD-
GND
DATA+
DATA-
N.C.
N.C.
GND
2
4
5
3
1
7
6 8
9
N.C.
N.C.
N.C.
N.C.
Pins
COM 4 Function
RS232 DIO
1
DCD DIO0
2
RXD DIO1
3
TXD DIO2
4
DTR DIO3
5
GND GND
6
DSR
DIO4
7
RTS
DIO5
8
CTS DIO6
9
RI DIO7
COM4/DIO Pin Select JP1 JP2
COM4 1-2, 4-5, 7-8,
10-11 On (default)
1-2, 4-5, 7-8,
10-11 On (default)
DIO 2-3, 5-6, 8-9,
11-12 On
2-3, 5-6, 8-9,
11-12 On
Mini PCIe/SATA Select
(for
the half-size Mini PCIe slot)
JP3
PCIe 2-3 On
SATA 1-2 On (default)
Clear CMOS JP4
Normal 1-2 On (default)
Clear CMOS 2-3 On
Auto Power-ON JP7
Normal 1-2 On (default)
Auto-PWR ON 2-3 On
DIO0
DIO1
DIO2
DIO3
GND
2
4
5
3
1
7
6 8
9
DIO4
DIO5
DIO6
DIO7
DIO
933-EC70A1-000G
A-581-Q-2003
DFI reserves the right to change the specifications at any time prior to the product's release.
This QIG may be based on editions that do not resemble your actual products. For the latest
revision and more details of the installation procedure, please refer to
https://go.dfi.com/EC70A-KU or scan the QR code on the right.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

DFI EC70A-KU User manual

DFI
Brand
DFI
Model
EC70A-KU
Type
User manual
This manual is also suitable for

DFI EC70A-KU is a compact and versatile system that offers a wide range of features for various industrial applications. With its rugged design, it can withstand harsh environments and operate reliably in industrial settings. The system supports multiple expansion options, including Mini PCIe and M.2 slots, allowing for customization and flexibility. Additionally, the наличието на множество портов ввода/вывода, таких как COM-порты, USB и LAN, обеспечивает различные возможности подключения для периферийных устройств и сетевого оборудования.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers