1
Functionality added in M-300 version 1.11
• Delay time can be set in sample units (p. 2).
• A function has been added to exclusively switch off sends to MAIN L/R or to MAIN C when sends to MAIN L/R and
MAIN C are on (p. 3).
• Functions that can be assigned to user buttons have been added (p. 3).
• A function has been added that automatically applies the channel names on the M-300 to the track names on the
R-1000 when an R-1000 48-track recorder/player is connected and the M-300 is used as a recording source (p. 4).
• The following RS-232C commands have been added.
For more information, refer to "V-Mixer RS-232C Reference."
◆ Control commands
• Display blackout/cancel blackout
• Display brightness setting
• Panel brightness setting
• Lamp brightness setting
◆ Request command
• REAC connection status request
• Display blackout status request
• Display brightness request
• Panel brightness request
• Lamp brightness request
◆ Reply-use commands
• Error status
• Connection-destination REAC device error status
1PS
2
Functionality added in M-300 version 1.11
Delays for MAIN L/R/C, AUX1 to 8, MTX1 to 4, and the delays provided for monitoring can be set using sample units.
1. At the SETUP section, press [SYSTEM].
The SYSTEM screen appears.
2. Use the DELAY UNIT selection button to select Sample.
Delay times can now be set using sample units.
Setting delay time in sample units
3
Functionality added in M-300 version 1.11
A function has been added to exclusively switch off sends to MAIN L/R or MAIN C when sends from CH1 to 32 and
AUX1 to 8 to MAIN L/R and MAIN C are on.
• Switching on sends to MAIN L/R MAIN C switched off sends to MAIN C.
• Switching on sends to MAIN C automatically switches off sends to MAIN L/R.
1. At the SETUP section, press [SYSTEM].
The SYSTEM screen appears.
2. At the MAIN OPTION selection buttons, select the check box for Mutually Exclusive LR/C
Assign.
Exclusion control is performed for sends to MAIN L/R and MAIN C.
The following functions can be assigned to user buttons.
Exclusion control of sends to MAIN L/R and MAIN C
Addition of functions assignable to user buttons
FUNCTION PARAM1 BUTTON Description
SYSTEM DISPLAY BLACKOUT
Flashing when the unit's display is
blacked out
Blacks out the unit's display
4
Functionality added in M-300 version 1.11
A function has been added that automatically applies the channel names on the M-300 to the track names on the R-
1000 when an R-1000 48-track recorder/player is connected via REAC and the M-300 is used as a recording source.
This function does not work when the version of the R-1000's system program is earlier than 1.100.
1. Display the R-1000 CONTROL popup.
2. At PREFERENCE, select the Name sync check box.
When recording is performed on the R-1000, the channel names on the M-300 used as the recording source are
applied to the track names on the R-1000.
The following rules are used to assign the track names according to the settings for the recording-use INPUT
patchbay on the R-1000 (the input connector assigned to the recording track) and the M-300's patchbay settings.
Automatic application of M-300 channel names to R-1000 track names
Assignment to R-1000 recording track Applied track name
MAIN L, R, C Channel name
MAIN MONO MAIN M
AUX 1 – 8
Channel name
MTX 1 – 4
MONITOR L, R MON L, MON R
REC L, R REC L, REC R
CH1 to 32 direct out Channel name
TALKBACK/OSCILLATOR TB/OSC
REAC A IN 1 – 40
When the corresponding input port is patched to the input channel,
the channel name.
When not patched, A IN1 to A IN40
REAC B IN 1 – 40
When the corresponding input port is patched to the input channel,
the channel name.
When not patched, B IN1 to B IN40
CONSOLE IN 1 – 12
When the corresponding input port is patched to the input channel,
the channel name.
When not patched, C IN1 to C IN12
-
1
-
2
-
3
-
4
