Bauknecht BKCIC 3C26 P Daily Reference Guide

Brand: Bauknecht

Model: BKCIC 3C26 P

Category: Dishwashers

Type: Daily Reference Guide

DAILY REFERENCE

GUIDE

THANK YOU FOR BUYING A BAUKNECHT PRODUCT.

In order to receive a more complete assistance, please

www.bauknecht.eu/register

You can download the Safety Instructions and the Use

and Care Guide, by visiting our website

docs.bauknecht.eu and following the Instructions on

the back of this booklet.

Before using the appliance carefully read Health and Safety guide.

PRODUCT DESCRIPTION

APPLIANCE

1. Upper rack

2. Foldable flaps

3. Upper rack height adjuster

4. Upper spray arm

5. Lower rack

6. Space Zone

7. Cutlery basket

8. Lower spray arm

9. Filter Assembly

10. Salt reservoir

11. Detergent and Rinse Aid dispensers

12. Rating plate

13. Control panel

0000 000 00000

Service:

CONTROL PANEL

1. On-Off/Reset button with indicator light

2. Program selection button

3. Salt refill indicator light

4. Rinse Aid refill indicator light

5. Program number and delay time indicator

6. Delay indicator light

7. Display

8. Multizone indicator light

9. Delay button

10. Multizone button

11. Turbo button with indicator light

12. Power Clean button with indicator light

13. Tablet (Tab) button with indicator light

1 2 3 4 5 6 7 8 9 10 11 12 13

FIRST TIME USE

SALT, RINSE AID AND DETERGENT

ADVICE REGARDING THE FIRST TIME USE

After installation, remove the stoppers from the racks and the retaining

elastic elements from the upper rack.

FILLING THE SALT RESERVOIR

The use of salt prevents the formation of LIMESCALE on the dishes and

on the machine’s functional components.

• It is important that the salt reservoir be never empty.

• It is important to set the water hardness.

The salt reservoir is located in the lower part of the dishwasher (see

PROGRAMS DESCRIPTION) and should be filled when the SALT REFILL

indicator light

in the control panel is lit.

1.Remove the lower rack and unscrew the

reservoir cap (anticlockwise).

2.Only the first time you do this: fill the salt

reservoir with water.

3.Position the funnel

(see figure)

and fill the salt

reservoir right up to its edge (approximately 1 kg);

it is not unusual for a little water to leak out.

4. Remove the funnel and wipe any salt residue away from the opening.

Make sure the cap is screwed on tightly, so that no detergent can get

into the container during the wash program (this could damage the

water softener beyond repair).

Whenever you need to add salt, it is mandatory to complete the

procedure before the beginning of the washing cycle.

SETTING THE WATER HARDNESS

To allow the water softener to work in a perfect way, it is essential that

the water hardness setting is based on the actual water hardness in

your house. This information can be obtained from your local water

supplier.

The factory setting is for average (3) water hardness.

• Switch on the appliance by pressing the ON/OFF button.

• Switch off the appliance by pressing the ON/OFF button.

• Hold down button P for 5 seconds, until you hear a beep.

• Switch on the appliance by pressing the ON/OFF button.

•

The current selection level number and the salt indicator light both flash.

• Press button P to select the desired hardness level (see WATER

HARDNESS TABLE).

• Switch off the appliance by pressing the ON/OFF button.

Setting is complete!

As soon as this procedure is complete, run a program without loading.

Only use salt that has been specifically designed for dishwashers.

After the salt has been poured into the machine, the SALT REFILL

indicator light switches off.

If the salt container is not filled, the water softener and the heating

element may be damaged as a result.

FILLING THE RINSE AID DISPENSER

Rinse aid makes dish DRYING easier. The rinse aid dispenser A should

be filled when the RINSE AID REFILL indicator light

in the control

panel is lit.

1. Open the dispenser

by pressing and pulling up the tab on the lid.

2. Carefully introduce the rinse aid as far as the maximum (110 ml)

reference notch of the filling space - avoid spilling it. If this happens,

clean the spill immediately with a dry cloth.

3. Press the lid down until you hear a click to close it.

NEVER pour the rinse aid directly into the tub.

ADJUSTING THE DOSAGE OF RINSE AID

If you are not completely satisfied with the drying results, you can ad-

just the quantity of rinse aid used.

• Switch the dishwasher on using the ON/OFF button.

• Switch it off using the ON/OFF button.

• Press button P three times - a beep will be heard.

• Switch it on using the ON/OFF button.

• The current selection level number and rinse aid indicator light flash.

• Press button P to select the level of rinse aid quantity to be

supplied.

• Switch it off using the ON/OFF button

Setting is complete!

If the rinse aid level is set to ZERO (ECO), no rinse aid will be supplied. The

LOW RINSE AID indicator light will not be lit if you run out of rinse aid.

A maximum of 5 levels can be set according to the dishwasher model.

The factory setting is specific to the model, please follow instruction

above to check this for your machine.

• If you see bluish streaks on the dishes, set a low number (1-2).

• If there are drops of water or limescale marks on the dishes, set a

high number (3-4).

FILLING THE DETERGENT DISPENSER

To open the detergent dispenser

use the opening device A. Introduce

the detergent into the dry dispenser

B only. Place the amount of

detergent for pre-washing directly

inside the tub.

1.When measuring out the detergent

refer to the mentioned earlier infor-

mation to add the proper quantity.

Inside the dispenser

there are indi-

cations to help the detergent dosing.

2. Remove detergent residues from the edges of the dispenser and

close the cover until it clicks.

3. Close the lid of the detergent dispenser by pulling it up until the

closing device is secured in place.

The detergent dispenser automatically opens up at the right time

according to the program. If all-in-one detergents are used, we

recommend using the

TABLE T

button, because it adjusts the program so

that the best washing and drying results are always achieved.

Water Hardness Table

Level

°dH

German degrees

°fH

French degrees

1 Soft 0 - 6 0 - 10

2 Medium 7 - 11 11 - 20

3 Average 12 - 17 21 - 30

4 Hard 18 - 34 31 - 60

5 Very hard 35 - 50 61 - 90

PROGRAMS TABLE

ECO program data is measured under laboratory conditions according to European Standard EN 50242. Note for Test Laboratories: For information on

comparative EN testing conditions, please send an email to the following address: [email protected]

Pre-treatment of the dishes is not needed before any of the programs.

*) Not all options can be used simultaneously.

**) The duration of the program shown on the display or in the booklet is an estimate calculated on standard conditions. The actual time may vary

depending on many factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of load,

load balancing, additional selected options and sensor calibration. The sensor calibration can increase program duration up to 20 min.

Standby consumption: Left-on mode consumption: 6 W - Off mode consumption: 0.5 W

PROGRAMS DESCRIPTION

Instructions on wash cycle selection.

ECO

Normally soiled crockery. Standard program, the most efficient in terms

of its combined energy and water consumption.

SENSOR

For normally soiled dishes with dried food residues. Senses the level of

soiling on the dishes and adjusts the program accordingly. When the

sensor is detecting the soil level an animation appears in the display

and the cycle duration is updated.

INTENSIVE

Program recommended for heavily soiled crockery, especially suitable

for pans and saucepans (not to be used for delicate items).

DAILY

Normally soiled crockery. Everyday cycle, that ensures optimal cleaning

performance in shorter time.

SILENT

Suitable for night-time operation of the appliance. Optimum

performance ensured.

EXPRESS 30’

Program to be used for lightly-soiled dishes with no dried food residues.

GLASS

Cycle for delicate items, which are more sensitive to high temperatures,

for example glasses and cups.

PRE-WASH

Crockery to be washed later. No detergent to be used with this

program.

Notes:

Please note that cycles like Express or Fast are most effective for lightly

soiled dishes.

To reduce consumption even further, only run the dishwasher

when it is full.

Program

Drying

phase

ActivEco

Available options

Detergent

container

Duration of

wash program

(h:min)

**)

Water

consumption

(litres/cycle)

Energy

consumption

(kWh/cycle)

Tub B

1. Eco 50° 3:10 9.5 0.93

2. Sensor 50-60° 01:25 - 3:00 7.0 - 14.0 0.90 - 1.40

3. Intensive 65° - - 2:50 14.0 1.50

4. Daily 50° - 1:35 13.0 1.15

5. Silent 50° - - 3:30 15.0 1.15

6. Express 30’ 50° - - - 0:30 9.0 0.55

7. Glass 45° - - 1:40 11.5 1.20

8. Pre-Wash - - - - - 0:12 4.5 0.01

OPTIONS AND FUNCTIONS

OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL).

DELAY

The start time of the program may be delayed for a period

of time between 1 and 12 hours.

1.Press the DELAY button: the corresponding symbol

appears on the display; each time you press the button,

the time (1h, 2h, etc. up to max. 12h) from the start of

the selected wash cycle will be increased.

2.Select the wash program and close the door: the timer

will begin counting down;

3.Once this time has elapsed, the indicator light switches

off and the wash cycle begins.

To adjust the delay time and select a shorter period of

time, press the DELAY button. To cancel it, press the

button repeatedly until the selected delayed start

indicator light switches off.

The wash program will start automatically as soon as the

door is shut.

The Delay function cannot be set once a wash cycle

has been started.

MULTIZONE

If there are not many dishes to be washed, a half loading

may be used in order to save water, electricity and

detergent.

Select the program and then press the MULTIZONE button:

the symbol of the chosen rack will appear on the display. By

default the appliance washes dishes in all racks.

To wash only the specific rack, press this button

repeatedly:

shown on the display (only lower rack)

shown on the display (only upper rack)

shown on the display (option is OFF and the appliance will

wash dishes in all racks).

Remember to load the upper or lower rack only, and to

reduce the amount of detergent accordingly.

TURBO

This option can be used to reduce the duration of the

main programs while maintaining the same washing and

drying performance levels.

After selecting the program, press the TURBO button and

the indicator light will switch on. To deselect the option,

press the same button again.

POWER CLEAN

Thanks to the additional power jets this option provides

a more intensive and powerful wash in the lower rack, in

the specific area. This option is recommended for

washing pots and casseroles. Press this button to activate

POWER CLEAN (the indicator lights up).

TABLET (Tab)

This setting allows you to optimize the performance of

the program according to the type of detergent used.

Press the TABLET button (the indicator light will light up)

if you use combined detergents in tablet form (rinse aid,

salt and detergent in 1 dose).

If you use powder or liquid detergent, this option

should be off.

ActivEco

ActivEco is a convection drying system which automatically opens the

door during/after drying phase to ensure exceptional drying

performance every day. Door opens at the temperature that is safe to

your kitchen furniture, thus door will not be opened when the option

of POWER CLEAN or TURBO are on.

As additional steam protection, special designed protection foil is

added together with the dishwasher. To see how to mount protection

foil please refer to (INSTALLATION GUIDE).

ActivEco functionality could be disabled by the user as follows:

1. Go to the Dishwasher software menu pressing and holding “

”

button (6 sec).

2. You switched to

ActivEco

Control Menu, you could change status of

ActivEco

functionality by pressing “

” button:

E – enabled d – disabled

To confirm the change and exit from the Control Menu please press

and hold “P” button (3 sec).

If an option is not compatible with the selected program see PROGRAMS TABLE, the corresponding LED flashes rapidly 3 times and beeps

will sound. The option will not be enabled.

DAILY USE

1. CHECK WATER CONNECTION

Check that the dishwasher is connected to the water supply and

that the tap is open.

2. SWITCH ON THE DISHWASHER

Open the door and press the ON/OFF button.

3. LOAD THE RACKS

(see LOADING THE RACKS)

4. FILLING THE DETERGENT DISPENSER

(see PROGRAMS TABLE).

5. CHOOSE THE PROGRAM AND CUSTOMISE THE CYCLE

Select the most appropriate program in accordance with the type

of crockery and its soiling level (see PROGRAMS DESCRIPTION) by

pressing the P button.

Select the desired options (see OPTIONS AND FUNCTIONS).

6. START

Start the wash cycle by closing the door. When the program starts

you hear a beep.

7. END OF WASH CYCLE

The end of the wash cycle is indicated by beeps and by the flashing

of the wash cycle number on the display. Open the door and switch

off the appliance by pressing the ON/OFF button.

Wait for a few minutes before removing the crockery - to avoid burns.

Unload the racks, beginning with the lower one.

The machine will switch off automatically during certain extended

periods of inactivity, in order to minimise electricity consumption.

If the crockery is only lightly soiled or if it has been rinsed with

water before being placed in the dishwasher, reduce the amount

of detergent used accordingly.

MODIFYING A RUNNING PROGRAM

If a wrong program was selected, it is possible to change it, provided

that it has only just begun: open the door (be ware of HOT steam!),

press and hold the ON/OFF button, the machine will switch off.

Switch the machine back on using the ON/OFF button and select the

new wash cycle and any desired options; start the cycle by closing the

door.

ADDING EXTRA CROCKERY

Without switching off the machine, open the door (be ware of HOT

steam!) and place the crockery inside the dishwasher. Close the door

and the cycle will begin from the point at which it was interrupted.

ACCIDENTAL INTERRUPTIONS

If the door is opened during the wash cycle, or if there is a power cut,

the cycle stops. It starts again from the point at which it was

interrupted once the door has been closed or the electricity supply is

restored.

For more information about the functions, you can request or download

from the WEB a Use & Care Guide by following the instructions on the last

page.

ADVICE AND TIPS

TIPS

Before loading the baskets, remove all food residues from the crockery

and empty the glasses. You do not need to rinse beforehand under

running water.

Arrange the crockery so that it is held in place firmly and does not tip

over; and arrange the containers with the openings facing downwards

and the concave/convex parts placed obliquely, thus allowing the

water to reach every surface and flow freely.

Warning: lids, handles, trays and frying pans do not prevent the

sprayer arms from rotating.

Place any small items in the cutlery basket.

Very soiled dishes and pans should be placed in the lower basket

because in this sector the water sprays are stronger and allow a higher

washing performance.

After loading the appliance, make sure that the sprayer arms can rotate

freely.

HYGIENE

To avoid odour and sediment which can be accumulated in the

dishwasher please run a high temperature program at least one a

month. Use a tea spoon of detergent and run it without the loading to

clean your appliance.

UNSUITABLE CROCKERY

• Wooden crockery and cutlery.

• Delicate decorated glasses, artistic handicraft and antique

crockery. Their decorations are not resistant.

• Parts in synthetic material which do not withstand high

temperatures.

• Copper and tin crockery.

• Crockery soiled with ash, wax, lubricating grease or ink.

The colours of glass decorations and aluminium/silver pieces can

change and fade during the washing process. Some types of glass (e.g.

crystal objects) can become opaque after a number of wash cycles too.

DAMAGE TO GLASS AND CROCKERY

• Only use glasses and porcelain guaranteed by the manufacturer as

dishwasher safe.

• Use a delicate detergent suitable for crockery

• Collect glasses and cutlery from the dishwasher as soon as the

wash cycle is over.

LOADING THE RACKS

UPPER RACK

Load delicate and light dishes:

glasses, cups, saucers, low salad

bowls.

(loading example for the upper rack)

ADJUSTING THE HEIGHT OF THE UPPER RACK

The height of the upper rack can be adjusted: high position to place

bulky crockery in the lower basket and low position to make the most

of the tip-up supports by creating more space upwards and avoid

collision with the items loaded into lower rack.

The upper rack is equipped with a Upper

Rack height adjuster (see figure), without

pressing the levers, lift it up by simply

holding the rack sides, as soon as the rack is

stable in its upper position.

To restore to the lower position, press the

levers A at the sides of the rack and move

the basket downwards.

We strongly recommend that you do not

adjust the height of the rack when it is

loaded.

NEVER raise or lower the basket on one side only.

FOLDABLE FLAPS WITH ADJUSTABLE POSITION

The side foldable flaps can be positioned at

three different heights to optimize the

arrangement of crockery inside the rack.

Wine glasses can be placed safely in the

foldable flaps by inserting the stem of each

glass into the corresponding slots.

For optimum drying results incline the

foldable flaps more. To change the inclination,

pull up the foldable flap, slide it slightly and

position it as you wish.

LOWER RACK

For pots, lids, plates, salad bowls, cutlery etc. Large plates and lids should

ideally be placed at the sides to avoid interferences with the spray arm.

The lower rack has tip-up supports which can be used in a vertical

position when arranging plates or in a horizontal position (lower) to

load pans and salad bowls easily.

(loading example for the lower rack)

POWER CLEAN IN LOWER RACK

Power Clean® uses the special water

jets in the rear of cavity to wash more

intensively the high dirty items.

Placing the pots/casseroles faced to

the Power Clean® component please

activate the POWER CLEAN on the

panel.

The lower rack has a Space Zone, a special pull-out support in the rear

of the rack that can be used to support frying pans or baking pans in

upright position, thus taking up less space.

How to use Power Clean®:

1. Adjust the Power Clean® area (G)

folding down the rear plate

holders to load pots.

2. Load pots and casseroles inclined

vertically in Power Clean® area.

Pots have to be inclined towards

the power water jets.

CUTLERY BASKET

The basket is equipped with top grilles

for improved cutlery arrangement. The

cutlery basket should be positioned only

at the front of the lower rack.

Knives and other utensils with sharp

edges must be placed in the cutlery

basket with the points facing

downwards or they must be

positioned horizontally in the tip-up

compartments on the upper rack.

CARE AND MAINTENANCE

CLEANING THE FILTER ASSEMBLY

Regularly clean the filter assembly so that the filters do not clog and

that the waste water flows away correctly.

The filter assembly consists of three filters which remove food residues

from the washing water and then recirculate the water: to obtain the

best washing results, you need to keep them clean.

The dishwasher must not be used without filters or if the filter is

loose.

After several washes, check the filter assembly and if necessary clean it

thoroughly under running water, using a non-metallic brush and

following the instructions below:

1. Turn the cylindrical filter

in an anti-clockwise direction and pull it

out

(Fig 1)

2. Remove the cup filter

by exerting a slight pressure on the side

flaps

(Fig 2)

3. Slide out the stainless-steel plate filter

(Fig 3)

4. Inspect the trap and remove any food residues.

NEVER REMOVE

the wash-cycle pump protection (black detail)

(Fig 4)

After cleaning the filters, re-place the filter assembly and fix it in

position correctly; this is essential for maintaining the efficient

operation of the dishwasher.

CLEANING THE SPRAY ARMS

On occasions, food residue may become encrusted onto the spray arms

and block the holes used to spray the water. It is therefore

recommended that you check the arms from time to time and clean

them with a small non-metallic brush.

To remove the upper spray arm, turn the plastic locking ring in an anti-

clockwise direction. The upper spray arm should be replaced so that

the side with the greater number of holes is facing upwards.

The lower spray arm may be removed by pulling it upwards.

CLEANING THE WATER INLET HOSE

If the water hoses are new or have not been used for an extended

period of time, let the water run to make sure it is clear and free of

impurities before performing the necessary connections. If this

precaution is not taken, the water inlet could become blocked and

damage the dishwasher.

TROUBLESHOOTING

MAINTENANCE AND TROUBLESHOOTING GUIDE

For more information, maintenance procedures and troubleshooting,

see the Use and Care Guide.

The Use and Care Guide can be obtained by:

• After-Sales Service; phone number see in warranty booklet.

• download from website: docs.bauknecht.eu

• use QR code

TECHNICAL DATASHEET

The technical data containing the energy consumption data can be

downloaded from the website: docs.bauknecht.eu

CONTACTING AFTER-SALES SERVICE

When you contact the After-Sales Service,

you must provide the codes shown on

the rating plate attached to the left or

right side inside the door of the

dishwasher. The phone number is listed

in the warranty booklet or on the website:

www.bauknecht.eu

Your dishwasher may not work properly.

Before contacting the Service Centre check if the problem can be solved by going through the following list.

PROBLEMS POSSIBLE CAUSES SOLUTIONS

The dishwasher

won’t start or does

not respond to

commands.

The appliance has not been plugged in

properly.

Insert the plug into the socket.

Power outage. The dishwasher starts automatically when the power returns.

The dishwasher door is not closed. Vigorously push the door until you hear the “click”.

It does not respond to commands. Switch off the appliance by pressing the ON/OFF button, switch it back on

after approximately one minute and reset the program.

The dishwasher

won’t drain.

The wash cycle has not finished yet. Wait until the wash cycle finishes.

The drain hose is bent. Check that the drain hose is not bent (see INSTALATION INSTRUCTION).

The sink drain pipe is blocked. Clean the sink drain pipe.

The filter is clogged up with food residues Clean the filter (see CLEANING THE FILTER ASSEMBLY).

The dishwasher

makes excessive

noise.

The dishes are rattling against each. Arrange the crockery correctly (see LOADING THE RACKS).

An excessive amount of foam has been

produced.

The detergent has not been measured out correctly or it is not suitable for

use in dishwashers (see FILLING THE DETERGENT DISPENSER). Reset dish-

washer by pressing the DRAIN button (see OPTIONS AND FUNCTIONS) and

run new program without detergent.

The dishes are not

clean.

The crockery has not been arranged

properly.

Arrange the crockery correctly (see LOADING THE RACKS).

The spray arms cannot rotate freely,

being hindered by the dishes.

Arrange the crockery correctly (see LOADING THE RACKS).

The wash cycle is too gentle. Select an appropriate wash cycle (see PROGRAMS TABLE).

An excessive amount of foam has been

produced.

The detergent has not been measured out correctly or it is not suitable for

use in dishwashers (see FILLING THE DETERGENT DISPENSER).

The cap on the rinse aid compartment

has not been shut correctly.

Make sure the cap of the rinse aid dispenser is closed.

The filter is soiled or clogged. Clean the filter assembly (see CARE AND MAINTENANCE).

There is no salt. Fill the salt reservoir (see FILLING THE SALT RESERVOIR).

IEC 436

400011355137

03/2019 as - Xerox Fabriano

Bauknecht BKCIC 3C26 P Daily Reference Guide

Brand: Bauknecht

Model: BKCIC 3C26 P

Category: Dishwashers

Type: Daily Reference Guide

Download PDF

report