Miller RUNNING GEAR NO. 24K Owner's manual

Brand: Miller

Model: RUNNING GEAR NO. 24K

Type: Owner's manual

This manual is also suitable for

June 1991 FORFORM:

Use above FORM number when ordering extra manuals.

OWNER’S MANUAL

OM-676A

No. 24 Running Gear 042 371

No. 24K Running Gear 042 615

The data contained in this supplement is either in addition to or takes exception to data appearing

later in this manual.

THIS INSTALLATION MUST BE PERFORMED BY QUALIFIED PERSONNEL FAMILIAR WITH STANDARD

SAFETY PRACTICES

WARNING: FALLING EQUIPMENT can cause serious personal injury and equipment damage.

• Use equipment of adequate capacity to lift the unit.

• If using lift forks to handle this unit, be sure the lift forks are long enough to extend out of the opposite side

of the base.

• Do not place any part of the body under the unit while it is suspended.

IMPORTANT: All directions, such as left or right, are with respect to the operator facing the welding generator front

panel. Refer to Figure 1 when performing this installation.

1 Insert axle (5) into running gear brackets (9).

IMPORTANT: The running gear wheels require periodic greasing.

2. Install wheels (2) and flat washers (4) onto axle (5), and secure wheels in place with retaining ring (6).

3. Slide handle (1) onto brackets, and be sure holes are aligned. Secure with supplied hardware.

4. Block wheels so that running gear cannot roll.

IMPORTANT: Be sure there is approximately 3/8 in. (9.5 mm) clearance between welding generator and the handle

(1).

5. Place welding generator onto brackets, and secure with U-bolts (3) and supplied hardware.

6. Remove blocks from wheels.

OM-676 Page 2

Description

Quantity

Figure 1. Running Gear

Model

24 24K

042 371

042 615

Item

No.

Part

No.

1 131 244 HANDLE, running gear 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1 145 672 HANDLE, running gear 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2 022 825 WHEEL, w/tire & brg, 8 inch tire 2 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3 022 609 BOLT, U stl .375-24 x 1.000 4 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4 133 812 WASHER, flat stl 1.062 ID x 1.500 OD x .134thk 4 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5 130 768 AXLE, running gear (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6 145 665 RING, retaining ext 1.000 shaft x .082 grove 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5 145 671 AXLE, running gear 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6 145 665 RING, retaining 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7 602 213 WASHER, lock stl split .375 8 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8 601 873 NUT, stl hex full fnsh .375-24 8 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9 145 669 BRACKET, mtg running gear 2 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10 604 318 NUT, stl slflkg hex hvy .250-20 2 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11 601 941 SCREW, cap stl hex hd .250-20 x 1.750 2 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SC-135 355-A

98 7 5

Figure 1. No. 24 Running Gear

BE SURE TO PROVIDE MODEL AND SERIAL NUMBER WHEN ORDERING REPLACEMENT PARTS.