Vega VEGAPULS 31 Operating instructions

Operating Instructions

Radar sensor for continuous level

measurement

VEGAPULS 31

Two-wire 4 … 20 mA/HART

Document ID: 57820

2

Contents

VEGAPULS 31 • Two-wire 4 … 20 mA/HART

57820-EN-191014

Contents

1 About this document ............................................................................................................... 4

1.1 Function ........................................................................................................................... 4

1.2 Target group ..................................................................................................................... 4

1.3 Symbols used................................................................................................................... 4

2 For your safety ......................................................................................................................... 5

2.1 Authorised personnel ....................................................................................................... 5

2.2 Appropriate use ................................................................................................................ 5

2.3 Warning about incorrect use ............................................................................................. 5

2.4 General safety instructions ............................................................................................... 5

2.5 EU conformity ................................................................................................................... 6

2.6 Installation and operation in the USA and Canada ........................................................... 6

2.7 Safety instructions for Ex areas ........................................................................................ 6

3 Product description ................................................................................................................. 7

3.1 Conguration

.................................................................................................................... 7

3.2 Principle of operation........................................................................................................ 9

3.3 Adjustment ....................................................................................................................... 9

3.4 Packaging, transport and storage ................................................................................... 10

3.5 Accessories.................................................................................................................... 11

4 Mounting ................................................................................................................................. 12

4.1 General instructions ....................................................................................................... 12

4.2 Mounting instructions ..................................................................................................... 13

4.3 Measurement setup - Flow ............................................................................................. 16

5 Connecting to power supply ................................................................................................. 19

5.1 Preparing the connection ............................................................................................... 19

5.2 Connecting ..................................................................................................................... 20

5.3 Wiring plan ..................................................................................................................... 21

5.4 Switch-on phase............................................................................................................. 22

6 Access protection .................................................................................................................. 23

6.1 Bluetooth radio interface ................................................................................................ 23

6.2 Protection of the parameterization .................................................................................. 23

7 Set up with the integrated display and adjustment unit .................................................... 25

7.1 Adjustment system ......................................................................................................... 25

7.2 Measured value and menu item display ......................................................................... 26

7.3 Menu overview ............................................................................................................... 27

7.4 Parameter adjustment .................................................................................................... 28

8 Setup with smartphone/tablet (Bluetooth) .......................................................................... 36

8.1 Preparations ................................................................................................................... 36

8.2 Connecting ..................................................................................................................... 36

8.3 Parameter adjustment .................................................................................................... 37

9 Setup with PC/notebook (Bluetooth) ................................................................................... 38

9.1 Preparations ................................................................................................................... 38

9.2 Connecting ..................................................................................................................... 38

9.3 Parameter adjustment .................................................................................................... 39

10 Setup with PC/notebook (VEGACONNECT) ........................................................................ 40

3

Contents

VEGAPULS 31 • Two-wire 4 … 20 mA/HART

57820-EN-191014

10.1 Connect the PC .............................................................................................................. 40

10.2 Parameter adjustment with PACTware ............................................................................ 41

10.3 Saving the parameterisation data ................................................................................... 42

11 Diagnostics and servicing .................................................................................................... 43

11.1 Maintenance .................................................................................................................. 43

11.2 Rectify faults ................................................................................................................... 43

11.3 Diagnosis, fault messages ............................................................................................. 44

11.4 Status messages according to NE 107 .......................................................................... 44

11.5 Treatment of measurement errors .................................................................................. 47

11.6 Software update ............................................................................................................. 50

11.7 How to proceed if a repair is necessary .......................................................................... 51

12 Dismount................................................................................................................................. 52

12.1 Dismounting steps.......................................................................................................... 52

12.2 Disposal ......................................................................................................................... 52

13 Certicatesandapprovals .................................................................................................... 53

13.1 Environmental instructions ............................................................................................. 53

14 Supplement ............................................................................................................................ 54

14.1 Technical data ................................................................................................................ 54

14.2 Dimensions .................................................................................................................... 59

14.3 Industrial property rights ................................................................................................. 60

14.4 Hash function acc. to mbed TLS ..................................................................................... 60

14.5 Trademark ...................................................................................................................... 60

Editing status: 2019-10-10

4

1 About this document

VEGAPULS 31 • Two-wire 4 … 20 mA/HART

57820-EN-191014

1 About this document

1.1 Function

This instruction provides all the information you need for mounting,

connection and setup as well as important instructions for mainte-

nance,faultrectication,theexchangeofpartsandthesafetyofthe

user. Please read this information before putting the instrument into

operation and keep this manual accessible in the immediate vicinity

of the device.

1.2 Target group

This operating instructions manual is directed to trained personnel.

Thecontentsofthismanualmustbemadeavailabletothequalied

personnel and implemented.

1.3 Symbols used

Document ID

This symbol on the front page of this instruction refers to the Docu-

ment ID. By entering the Document ID on www.vega.com you will

reach the document download.

Information, note, tip: This symbol indicates helpful additional infor-

mation and tips for successful work.

Note: This symbol indicates notes to prevent failures, malfunctions,

damage to devices or plants.

Caution: Non-observance of the information marked with this symbol

may result in personal injury.

Warning: Non-observance of the information marked with this symbol

may result in serious or fatal personal injury.

Danger: Non-observance of the information marked with this symbol

results in serious or fatal personal injury.

Ex applications

This symbol indicates special instructions for Ex applications.

•

List

The dot set in front indicates a list with no implied sequence.

1 Sequence of actions

Numbers set in front indicate successive steps in a procedure.

Battery disposal

This symbol indicates special information about the disposal of bat-

teries and accumulators.

5

2 For your safety

VEGAPULS 31 • Two-wire 4 … 20 mA/HART

57820-EN-191014

2 For your safety

2.1 Authorised personnel

All operations described in this documentation must be carried out

onlybytrained,qualiedpersonnelauthorisedbytheplantoperator.

During work on and with the device, the required personal protective

equipment must always be worn.

2.2 Appropriate use

VEGAPULS 31 is a sensor for continuous level measurement.

Youcannddetailedinformationabouttheareaofapplicationin

chapter "Product description".

Operational reliability is ensured only if the instrument is properly

usedaccordingtothespecicationsintheoperatinginstructions

manual as well as possible supplementary instructions.

2.3 Warning about incorrect use

Inappropriate or incorrect use of this product can give rise to applica-

tion-specichazards,e.g.vesseloverllthroughincorrectmounting

or adjustment. Damage to property and persons or environmental

contamination can result. Also, the protective characteristics of the

instrument can be impaired.

2.4 General safety instructions

This is a state-of-the-art instrument complying with all prevailing

regulations and directives. The instrument must only be operated in a

technicallyawlessandreliablecondition.Theoperatorisresponsi-

ble for the trouble-free operation of the instrument. When measuring

aggressive or corrosive media that can cause a dangerous situation

if the instrument malfunctions, the operator has to implement suitable

measures to make sure the instrument is functioning properly.

During the entire duration of use, the user is obliged to determine the

compliance of the necessary occupational safety measures with the

current valid rules and regulations and also take note of new regula-

tions.

The safety instructions in this operating instructions manual, the na-

tional installation standards as well as the valid safety regulations and

accident prevention rules must be observed by the user.

For safety and warranty reasons, any invasive work on the device

beyond that described in the operating instructions manual may be

carried out only by personnel authorised by the manufacturer. Arbi-

traryconversionsormodicationsareexplicitlyforbidden.Forsafety

reasons,onlytheaccessoryspeciedbythemanufacturermustbe

used.

To avoid any danger, the safety approval markings and safety tips on

the device must also be observed.

The low transmitting power of the radar sensor is far below the inter-

nationally approved limits. No health impairments are to be expected

6

2 For your safety

VEGAPULS 31 • Two-wire 4 … 20 mA/HART

57820-EN-191014

with intended use. The band range of the transmission frequency can

be found in chapter "Technical data".

2.5 EU conformity

ThedevicefullsthelegalrequirementsoftheapplicableEUdirec-

tives.ByaxingtheCEmarking,weconrmtheconformityofthe

instrument with these directives.

The EU conformity declaration can be found on our homepage.

2.6 Installation and operation in the USA and

Canada

This information is only valid for USA and Canada. Hence the follow-

ing text is only available in the English language.

Installations in the US shall comply with the relevant requirements of

the National Electrical Code (ANSI/NFPA 70).

Installations in Canada shall comply with the relevant requirements of

the Canadian Electrical Code.

2.7 Safety instructions for Ex areas

For Ex applications, only devices with corresponding Ex approval may

beused.ObservetheEx-specicsafetyinstructions.Thesearean

integral part of the operating instructions and are enclosed with every

device with Ex approval.

7

3 Product description

VEGAPULS 31 • Two-wire 4 … 20 mA/HART

57820-EN-191014

3 Product description

3.1 Conguration

The scope of delivery encompasses:

•

VEGAPULS 31 radar sensor

•

Information sheet "Documents and software" with:

– Instrument serial number

– QR code with link for direct scanning

•

Information sheet "PINs and Codes" with:

– Bluetooth access code

– DataMatrix code with link for direct scanning

•

Information sheet "Emergency unlock codes" with:

– Bluetooth access code

– Bluetooth unlock code

– Device unlock code

The further scope of delivery encompasses:

•

Documentation

– Ex-specic"Safety instructions" (with Ex versions)

– Ifnecessary,furthercerticates

Note:

Optional instrument features are also described in this operating

instructions manual. The respective scope of delivery results from the

orderspecication.

This operating instructions manual applies to the following instrument

versions:

•

Hardware version from 1.0.0

•

Software version from 1.0.0

Scope of delivery

Scope of this operating

instructions

8

3 Product description

VEGAPULS 31 • Two-wire 4 … 20 mA/HART

57820-EN-191014

4

6

5

1

2

3

Fig. 1: Components of VEGAPULS 31

1 Radar antenna

2 Processtting

3 Process seal

4 Electronics housing

5 Display and adjustment unit

6 Ventilation/pressure compensation

Thetypelabelcontainsthemostimportantdataforidenticationand

use of the instrument.

0044

VEGAPULS 3.

s/n 12345678

12...35V

4...20mA HART

IP66/IP67, TYPE 4x

0...15m

4

123456

TA G1234

1

5

6

2

3

2019

www.vega.com

D-77761 SCHILTACH,

Made in Germany

MWP 3bar (300kPa)

PVDF

Fig. 2: Layout of the type label (example)

1 Instrument type

2 Field for approvals

3 Technical data

4 Number or DataMatrix code for Bluetooth access

5 QR code for device documentation

6 Serial number

Move to "www.vega.com"andenterinthesearcheldtheserial

number of your instrument.

Thereyoucanndthefollowinginformationabouttheinstrument:

•

Order data

•

Documentation

•

Software

Alternatively,youcanndallviayoursmartphone:

•

Scan the QR-code on the type label of the device or

Constituent parts

Type label

Documents and softwar

e

9

3 Product description

VEGAPULS 31 • Two-wire 4 … 20 mA/HART

57820-EN-191014

•

Enter serial number manually in the VEGA Tools app (available

free of charge in the respective stores)

3.2 Principle of operation

VEGAPULS 31 is a radar sensor for continuous level measurement. It

is suitable for liquids and solids in virtually all industries, particularly in

the water and waste water industry.

The instrument emits a continuous, frequency-modulated radar signal

throughitsantenna.Theemittedsignalisreectedbythemedium

andreceivedbytheantennaasanechowithmodiedfrequency.The

frequency change is proportional to the distance and is converted into

thellingheight.

3.3 Adjustment

On-site adjustment of the device is carried out via the integrated

display and adjustment unit.

Note:

The housing with display and adjustment unit can be rotated 330° for

optimum readability and operability without tools.

Devices with integrated Bluetooth module can be adjusted wirelessly

via standard adjustment tools:

•

Smartphone/tablet (iOS or Android operating system)

•

PC/notebook (Windows operating system)

1

3

2

Fig. 3: Wireless connection to standard operating devices with integrated

Bluetooth LE

1 Sensor

2 Smartphone/Tablet

3 PC/Notebook

Devices with signal output 4 … 20 mA/HART can also be operated

via a signal cable. This is done via an interface adapter and a PC/

notebook using DTM/PACTware.

Application area

Functional principle

Local adjustment

Wireless adjustment

Adjustment via the signal

cable

10

3 Product description

VEGAPULS 31 • Two-wire 4 … 20 mA/HART

57820-EN-191014

1

2 4

3

5

OPEN

TWIST

USB

LOCK

Fig. 4: Connecting the PC to the signal cable

1 Sensor

2 HARTresistance250Ω(optionaldependingonevaluation)

3 Connection cable with 2 mm pins and terminals

4 Voltage supply

5 Interface adapter VEGACONNECT

3.4 Packaging, transport and storage

Your instrument was protected by packaging during transport. Its

capacity to handle normal loads during transport is assured by a test

based on ISO 4180.

The packaging consists of environment-friendly, recyclable card-

board. For special versions, PE foam or PE foil is also used. Dispose

of the packaging material via specialised recycling companies.

Transport must be carried out in due consideration of the notes on the

transport packaging. Nonobservance of these instructions can cause

damage to the device.

The delivery must be checked for completeness and possible transit

damage immediately at receipt. Ascertained transit damage or con-

cealed defects must be appropriately dealt with.

Up to the time of installation, the packages must be left closed and

stored according to the orientation and storage markings on the

outside.

Unless otherwise indicated, the packages must be stored only under

the following conditions:

•

Not in the open

•

Dry and dust free

•

Not exposed to corrosive media

•

Protected against solar radiation

•

Avoiding mechanical shock and vibration

The permissible storage and transport temperatures can be found in

chapter "Supplement - Technical data - Ambient conditions"

Packaging

T

ranspor

t

Transport inspection

Storage

Storage and transport

temperature

11

3 Product description

VEGAPULS 31 • Two-wire 4 … 20 mA/HART

57820-EN-191014

3.5 Accessories

The instructions for the listed accessories can be found in the down-

load area on our homepage.

Screwedangesareavailableindierentversionsaccordingtothe

following standards: DIN 2501, EN 1092-1, BS 10, ASME B 16.5,

JIS B 2210-1984, GOST 12821-80.

Welded sockets are used to connect the sensors to the process.

Threaded adapters enable simple adaptation of sensors with stand-

ardthreadedttings,e.g.toprocess-sidehygieneconnections.

The mounting accessories include e.g. bracket and mounting bracket

and are used for stable mounting of the sensor at the measuring

point. The parts are available in various versions and sizes.

Flanges

Welded sockets and

adapters

Mounting accessories

12

4 Mounting

VEGAPULS 31 • Two-wire 4 … 20 mA/HART

57820-EN-191014

4 Mounting

4.1 General instructions

The instrument is suitable for standard and extended ambient condi-

tions acc. to DIN/EN/IEC/ANSI/ISA/UL/CSA 61010-1. It can be used

indoors as well as outdoors.

Note:

For safety reasons, the instrument must only be operated within the

permissibleprocessconditions.Youcannddetailedinformationon

the process conditions in chapter "Technical data" of the operating

instructions or on the type label.

Hence make sure before mounting that all parts of the instrument ex-

posed to the process are suitable for the existing process conditions.

These are mainly:

•

Active measuring component

•

Processtting

•

Process seal

Process conditions in particular are:

•

Process pressure

•

Process temperature

•

Chemical properties of the medium

•

Abrasionandmechanicalinuences

Protect your instrument against moisture ingress through the following

measures:

•

Use a suitable connection cable (see chapter "Connecting to

power supply")

•

Tighten the cable gland or plug connector

•

Lead the connection cable downward in front of the cable entry or

plug connector

This applies mainly to outdoor installations, in areas where high

humidity is expected (e.g. through cleaning processes) and on cooled

or heated vessels.

Note:

Makesurethatthedegreeofcontaminationspeciedinchapter

"Technical data" meets the existing ambient conditions.

Note:

Make sure that during installation or maintenance no moisture or dirt

can get inside the instrument.

To maintain the housing protection, make sure that the housing lid is

closed during operation and locked, if necessary.

Ambient conditions

Process conditions

Protection against mois-

ture

13

4 Mounting

VEGAPULS 31 • Two-wire 4 … 20 mA/HART

57820-EN-191014

4.2 Mounting instructions

Radar sensors for level measurement emit electromagnetic waves.

The polarization is the direction of the electrical component of these

waves.

The polarization direction is marked on the housing, see following

drawing:

1

Fig. 5: Position of the polarisation

1 Marking of the polarisation

Note:

When the housing is rotated, the direction of polarization changes

andhencetheinuenceofthefalseechoonthemeasuredvalue.

Please keep this in mind when mounting or making changes later.

The lower side of the radar antenna is the beginning of the measur-

ing range. It is at the same time the reference plane for the min./max.

adjustment, see following diagram:

1

Fig. 6: Reference plane

1 Reference plane

When mounting the sensor, keep a distance of at least 200 mm

(7.874 in) from the vessel wall. If the sensor is installed in the center

of dished or round vessel tops, multiple echoes can arise. However,

these can be suppressed by an appropriate adjustment (see chapter

"Set up").

If you cannot maintain this distance, you should carry out a false

signal suppression during setup. This applies particularly if buildup on

the vessel wall is expected. In such cases, we recommend repeating

the false signal suppression at a later date with existing buildup.

Polarisation

Reference plane

Installation position

14

4 Mounting

VEGAPULS 31 • Two-wire 4 … 20 mA/HART

57820-EN-191014

> 200 mm

(7.87

")

Fig. 7: Mounting of the radar sensor on round vessel tops

In vessels with conical bottom it can be advantageous to mount the

sensor in the centre of the vessel, as measurement is then possible

down to the bottom.

Fig. 8: Mounting of the radar sensor on vessels with conical bottom

Donotmounttheinstrumentsinorabovethellingstream.Makesure

thatyoudetecttheproductsurface,nottheinowingproduct.

Fig.9:Mountingoftheradarsensorwithinowingmedium

With threaded connection, the antenna end should protrude at least

5 mm (0.2 in) out of the socket.

Inowingmedium

Threaded socket und

socket piece

15

4 Mounting

VEGAPULS 31 • Two-wire 4 … 20 mA/HART

57820-EN-191014

ca. 5 mm

Fig. 10: Thread mounting

Ifthereectivepropertiesofthemediumaregood,youcanmount

VEGAPULS 31 on sockets longer than the antenna. The socket end

should be smooth and burr-free, if possible also rounded.

Youwillndrecommendedvaluesforsocketheightsinthefollowing

illustration or the table. The values come from typical applications.

Deviating from the proposed dimensions, also longer sockets are

possible, however the local conditions must be taken into account.

d

h

Fig. 11: Socket mounting

Socket diameter d Socket length h

40 mm 1½" ≤150mm ≤5.9in

50 mm 2" ≤200mm ≤7.9in

80 mm 3" ≤300mm ≤11.8in

100 mm 4" ≤400mm ≤15.8in

150 mm 6" ≤600mm ≤23.6in

Note:

When mounting on longer sockets, we recommend carrying out a

false signal suppression (see chapter "Parameter adjustment").

The mounting location of the radar sensor should be a place where no

otherequipmentorxturescrossthepathoftheradarsignals.

Vessel installations, such as e.g. ladders, limit switches, heating spi-

rals, struts, etc., can cause false echoes and impair the useful echo.

Make sure when planning your measuring point that the radar sensor

has a "clear view" to the measured product.

In case of existing vessel installations, a false signal suppression

should be carried out during setup.

If large vessel installations such as struts or supports cause false

echoes, these can be attenuated through supplementary measures.

Small,inclinedsheetmetalbaesabovetheinstallationsscatterthe

radarsignalsandpreventdirectinterferingreections.

Vessel installations

16

4 Mounting

VEGAPULS 31 • Two-wire 4 … 20 mA/HART

57820-EN-191014

Fig.12:Coverat,large-areaproleswithdeectors

In liquids, direct the sensor as perpendicular as possible to the prod-

uct surface to achieve optimum measurement results.

Fig. 13: Alignment in liquids

If there are agitators in the vessel, a false signal suppression should

be carried out with the agitators in motion. This ensures that the

interferingreectionsfromtheagitatorsaresavedwiththebladesin

dierentpositions.

Fig. 14: Agitators

Throughtheactionoflling,stirringandotherprocessesinthevessel,

compact foams which considerably damp the emitted signals may

form on the product surface.

If foams lead to measurement errors, you should use the biggest pos-

sible radar antennas or sensors with guided radar.

4.3 Measurement setup - Flow

In general, the following must be observed while mounting the sensor:

Sensor orientation

Agitators

Foam generation

17

4 Mounting

VEGAPULS 31 • Two-wire 4 … 20 mA/HART

57820-EN-191014

•

Mounting the sensor on the upstream or inlet side

•

Installationinthecentreoftheumeandverticaltotheliquid

surface

•

DistancetotheoverfalloriceorVenturiume

•

Min. distance to the max. height of damming for optimum accu-

racy: 250 mm (9.843 in)

1)

Detailed project planning data can be found at the channel manufac-

turers and in the technical literature.

Themeasurementcanbeindividuallyconguredfortherespective

umeviaaPC/notebookandPACTware/DTM.Themeasurementcan

beindividuallyconguredfortherespectiveumeviaaPC/notebook

and PACTware/DTM.

Thefollowingexamplesserveasanoverviewforowmeasurement.

3 ... 4 h

max

90°

2

3

1

h

max

≥ 2 x h

max

90°

42 3

≥ 250 mm

(

9.84")

≥ 250 mm

(9.84")

Fig.15:Flowmeasurementwithrectangularume:h

max.

=max.llingofthe

rectangularume

1 Overoworice(sideview)

2 Headwater

3 Tailwater

4 Overfallorice(viewfromtailwater)

Rectangular overfall

1)

At smaller distances the measuring accuracy is reduced, see Technical data.

18

4 Mounting

VEGAPULS 31 • Two-wire 4 … 20 mA/HART

57820-EN-191014

2

3 ... 4 x h

max

90°

h

max

B

1

≥ 250 mm

(

9.84")

Fig.16:FlowmeasurementwithKhafagi-Venturiume:h

max.

=max.llingofthe

ume;B=tightestconstrictionintheume

1 Position sensor

2 Venturiume

Khafagi-Venturiume

19

5 Connecting to power supply

VEGAPULS 31 • Two-wire 4 … 20 mA/HART

57820-EN-191014

5 Connecting to power supply

5.1 Preparing the connection

Always keep in mind the following safety instructions:

•

Carryoutelectricalconnectionbytrained,qualiedpersonnel

authorised by the plant operator

•

If overvoltage surges are expected, overvoltage arresters should

be installed

Warning:

Only connect or disconnect in de-energized state.

Thedataforpowersupplyarespeciedinchapter"Technical data".

Note:

Power the instrument via an energy-limited circuit (power max. 100 W)

acc. to IEC 61010-1, e.g.

•

Class 2 power supply unit (acc. to UL1310)

•

SELV power supply unit (safety extra-low voltage) with suitable

internal or external limitation of the output current

Keepinmindthefollowingadditionalfactorsthatinuencetheoperat-

ing voltage:

•

Lower output voltage of the power supply unit under nominal load

(e.g. with a sensor current of 20.5 mA or 22 mA in case of fault)

•

Inuenceofadditionalinstrumentsinthecircuit(seeloadvaluesin

chapter "Technical data")

Use cable with round cross section for instruments with housing and

cablegland.Toensurethesealeectofthecablegland(IPprotection

rating),ndoutwhichcableouterdiameterthecableglandissuitable

for.

The instrument is connected with standard two-wire cable. If electro-

magnetic interference is expected which is above the test values of

EN 61326-1 for industrial areas, screened cable should be used.

Note:

Screened cable generally necessary in HART multidrop mode.

Note:

If the temperatures are too high, the cable insulation can be dam-

aged. Hence keep apart from the ambient temperature also the self-

heating of the instrument for the temperature resistance of the cable

in the connection compartment in mind

2)

.

If shielded cable is required, we recommend that the cable screening

be connected to ground potential on one side of the supply side.

Safety instructions

Voltage supply

Connection cable

Cable screening and

grounding

2)

 Withanambienttemperature≥50°C(122°F)theconnectioncableshould

be suitable for a temperature which is at least 20 °C (36 °F) higher.

20

5 Connecting to power supply

VEGAPULS 31 • Two-wire 4 … 20 mA/HART

57820-EN-191014

In Ex systems, the grounding is carried out according to the installa-

tion regulations.

Metric threads

In the case of instrument housings with metric thread, the cable gland

is screwed in at the factory. It is sealed with plastic plugs as transport

protection.

You have to remove this plug before electrical connection.

NPT thread

In the case of instrument housings with self-sealing NPT threads, it

is not possible to have the cable entry screwed in at the factory. The

free opening for the cable gland is therefore covered with a red dust

protection cap as transport protection.

Note:

Prior to setup you have to replace this protective cap with an ap-

proved NPT cable gland or close the opening with a suitable blind

plug.

Note:

Do not use grease when screwing in the NPT cable gland or a conduit

steel pipe.

Maximum torque see chapter "Technical data".

5.2 Connecting

The voltage supply and signal output are connected via the spring-

loaded terminals in the housing.

Note:

Fixedconductorsandexibleconductorswithferrulescanbeinsert-

eddirectlyintotheterminalopenings.Inthecaseofexibleconduc-

tors for opening the terminals, use a screwdriver (3 mm blade width)

to push the actuator lever away from the terminal opening (snaps

into place). To unlock, press the actuator lever slightly from behind to

close the terminals again.

Cable gland

Connection technology

Page is loading ...

Vega VEGAPULS 31 Operating instructions

Related papers

Other documents