Exmark Metro HP MHP4815KA User manual

Brand: Exmark

Model: Metro HP MHP4815KA

Category: Lawnmowers

Type: User manual

WARNING

The engine exhaust from this product

contains chemicals known to the State of

California to cause cancer, birth defects,

or other reproductive harm.

IMPORTANT

When the mower is used or operated on any California forest, brush or grass covered land, a working

spark arrester must be attached to the muffler. If not, the operator is violating state law, Section 442

Public Resource Code. To acquire a spark arrester for your unit, see your Engine Service Dealer.

WARNING

POTENTIAL HAZARD

♦

This product is a piece of power equipment.

WHAT CAN HAPPEN

♦

Failure to follow safe operating practices can result in serious

operator injury or even death.

HOW TO AVOID THE HAZARD

♦

Keep all shields, guards and safety devices (especially the grass

discharge system) in place and in proper working condition.

♦

Stop engine and remove spark plug wire(s) or remove key and

wait for all moving parts to stop before adjusting, servicing, or

performing maintenance.

♦

If mower deck becomes clogged, stop engine and remove spark

plug wire(s) or remove key and wait for all moving parts to stop

before cleaning blockage.

♦

Keep hands, feet and clothing away from power driven parts.

♦

Keep off mower unless seat platform is provided.

♦

Keep others off mower.

WARNING

POTENTIAL HAZARD

♦

Gasoline is harmful or fatal if swallowed. Long-term exposure to

vapors has caused cancer in laboratory animals.

WHAT CAN HAPPEN

♦

Failure to use caution may cause serious injury or illness.

HOW TO AVOID THE HAZARD

♦

Avoid prolonged breathing of vapors.

♦

Keep face away from nozzle and gas tank/container opening.

♦

Keep away from eyes and skin.

♦

Never siphon by mouth.

Exmark reserves the right to make changes or add improvements to its products at any time without

incurring any obligation to make such changes to products manufactured previously. Exmark, or its

distributors and dealers, accept no responsibility for variations which may be evident in the actual

specifications of its products and the statements and descriptions contained in this publication.

iii

EXMARK PARTS PLUS







PROGRAM

EFFECTIVE DATE: September 1, 1995

Program

If your Exmark dealer does not have the Exmark part in stock,

Exmark will get the parts to the dealer the next business day or

the part will be FREE* Guaranteed!!

How the Program Works

1. If dealer does not have part in stock for a "down" unit at

the time of request by customer, the dealer contacts his

distributor by 1:00 p.m., local time, and requests Exmark

Parts Plus







shipment of six (6) line items or less.

2. Distributor ships part(s) to dealer or customer, as

requested by dealer, same day, overnight UPS

Distributor bills dealer for part and freight charges where

applicable.

3. If distributor does not have the part(s) in stock to satisfy Exmark Parts Plus







order, he contacts Exmark by 3:00 p.m.,

central time, with an Exmark Parts Plus







order of six (6) line items or less.

4. If order is received by 3:00 p.m. central time, Exmark ships part(s) direct to dealer or customer, as requested by

distributor, same day, overnight UPS, Exmark bills the distributor for parts and shipping charges, where applicable.

5. The customer pays for the part and freight

if it is shipped under the Exmark Parts Plus







and if it arrives in

accordance to the program.

6. Who pays for the part and freight

if it fails to arrive overnight in accordance to the program?

A. Under any circumstance the customer does not pay.

B. If the part does not arrive overnight due to:

1. The dealer not submitting the Exmark Parts Plus







order to his Exmark distributor by 1:00 p.m., the dealer

pays for the part and freight.

2. The Distributor being unable to ship the part the same day or not submitting the Exmark Parts Plus







order

to Exmark by 3:00 p.m., central time, the Distributor pays for the part and freight.

3. Exmark being unable to ship the part and the Exmark parts order is received by 3:00 p.m., central time,

Exmark pays for the part and freight.

4. If the part does not arrive overnight due to the shipper (UPS), the shipper pays for the freight and Exmark

pays for the part.

The following restrictions apply

-- The Exmark Parts Plus







Program is available only through participating Exmark

Dealers and applies only to orders submitted on this program Monday through Thursday. Parts Plus service is available

only in the 48 contiguous United States. UPS has initiated a Saturday delivery program to many areas of the continental

United States and can be requested for an overnight shipment on Friday to be delivered Saturday. The next day air

charge, plus the Saturday delivery fee will be the responsibility of the purchaser. Exmark Mfg. will assume no

responsibility for Saturday delivery shipments. To qualify, all Exmark Parts Plus







orders must be received by Exmark by

3:00 p.m., central time. Orders must be six (6) line items or less. Exclusions from the Exmark Parts Plus







Program are:

Any wholegood or accessory in its entirety, engines and engine replacement parts, 5-speed Peerless transmissions and

5-speed transaxles, hydraulic or hydrostatic wheel motors, cutter decks and engine decks or any item exceeding United

Parcel Service size and weight restrictions.

Due to UPS restrictions, aerosol spray paint is considered a hazardous material and cannot be shipped via UPS next day

or Second Day Air.

Exmark Manufacturing stocks a limited supply of parts for transaxles, pumps and wheel motors. These parts can be

ordered for Next Day Air shipment but will not be guaranteed per the Parts Plus Program.

CONGRATULATIONS

on the purchase of your Exmark Mower. This product has been carefully

designed and manufactured to give you a maximum amount of dependability and years of trouble-

free operation.

OPERATOR'S MANUAL

This manual contains assembly, operating, maintenance, adjustment and safety instructions

for your Exmark mower.

BEFORE OPERATING YOUR MOWER, CAREFULLY READ THIS MANUAL IN ITS

ENTIRETY.

By following the operating, maintenance and safety instructions, you will prolong the life of

your mower, maintain its maximum efficiency and promote safe operation.

If additional information is needed, or should you require trained mechanic service, contact

your authorized Exmark equipment dealer or distributor.

All Exmark equipment dealers and distributors are kept informed of the latest methods of

servicing and are equipped to provide prompt and efficient service in the field or at their service

stations. They carry ample stock of service parts or can secure them promptly for you from the

factory.

All Exmark parts are thoroughly tested and inspected before leaving the factory, however,

attention is required on your part if you are to obtain the fullest measure of satisfaction and

performance.

TABLE OF CONTENTS

1. SAFETY .............................................................................................PAGE

1.1 Safety Alert Symbol......................................................................................1

1.2 Training........................................................................................................1

1.3 Preparation................................................................................................1-3

1.4 Operation ..................................................................................................3-4

1.5 Maintenance & Storage.............................................................................4-5

1.6 Riding Attachments......................................................................................5

1.7 Safety Signs..............................................................................................5-8

2. SPECIFICATIONS

2.1 Model Number..............................................................................................8

2.2 Engine..........................................................................................................8

2.3 Fuel System .................................................................................................8

2.4 Safety Interlock System................................................................................8

2.5 Steering/Brake Control.................................................................................8

2.6 Transmission................................................................................................9

2.7 Wheel Drive System.....................................................................................9

2.8 Tires ............................................................................................................9

2.9 Deck ............................................................................................................9

2.10 Dimensions.............................................................................................9-10

2.11 Torque Requirements................................................................................ 10

3. ASSEMBLY INSTRUCTIONS

3.1 to 3.18 Assembly...................................................................................10-15

4. OPERATION INSTRUCTIONS

4.1 Controls.................................................................................................15-17

4.2 Pre-Start................................................................................................17-18

4.3 Operation Instructions...........................................................................18-21

4.4 Transporting...............................................................................................21

5. MAINTENANCE & ADJUSTMENTS

5.1 Periodic Maintenance............................................................................21-27

5.2 Adjustments ..........................................................................................27-30

6. TROUBLE SHOOTING

6.1 Mower Pulling Left or Right ........................................................................30

6.2 Mower Cuts Unevenly................................................................................. 30

6.3 Engine Will Not Start.............................................................................30-31

7. WIRING DIAGRAM

...................................................................................32-33

WARRANTY

..............................................................................................34-35

- 1 -

1. SAFETY

1.1 SAFETY ALERT SYMBOL

THIS SAFETY ALERT SYMBOL

IS USED BOTH IN THIS MANUAL AND ON

THE MACHINE TO IDENTIFY IMPORTANT SAFETY MESSAGES WHICH MUST BE

FOLLOWED TO AVOID ACCIDENTS. THIS SYMBOL MEANS:

ATTENTION! BECOME ALERT!

YOUR SAFETY IS INVOLVED!

The safety alert symbol appears above information which alerts you of unsafe actions

or situations and will be followed by the word

DANGER

WARNING

, or

CAUTION.

When used with the word DANGER: IT DENOTES THAT AN EXTREME HAZARD

EXISTS WHICH WOULD RESULT IN HIGH PROBABILITY OF DEATH OR

IRREPARABLE INJURY IF PROPER PRECAUTIONS ARE NOT TAKEN.

When used with the word WARNING: IT DENOTES THAT A HAZARD EXISTS

WHICH CAN RESULT IN INJURY OR DEATH IF PROPER PRECAUTIONS ARE

NOT TAKEN.

When used with the word CAUTION: IT DENOTES A REMINDER OF SAFETY

PRACTICES OR DIRECTS ATTENTION TO UNSAFE PRACTICES WHICH COULD

RESULT IN PERSONAL INJURY IF PROPER PRECAUTIONS ARE NOT TAKEN.

1.2 TRAINING

1.2.1 Regard the Exmark mower as a piece of power equipment and teach this

regard to all who operate this unit.

1.2.2 Read the instructions carefully. Familiarize yourself with the controls and the

proper use of the equipment.

1.2.3 Never allow children, teenagers, or people unfamiliar with these instructions to

use the mower.

1.2.4 Avoid mowing while people, especially children, or pets, are nearby. Keep in

mind that the operator or user is

responsible for accidents or hazards occurring to other people or their property.

1.3 PREPARATION

1.3.1 The use of personal protective equipment, such as (but not limited to)

protection for the eyes, ears, feet and head is recommended.

1.3.2 While mowing, always wear substantial footwear and long trousers. Do not

operate equipment when barefoot or when wearing open sandals.

1.3.3 Thoroughly inspect the area where the equipment is to be used and remove all

stones, sticks, wires, bones and other foreign objects which may damage the

equipment or cause personal injury to the operator or bystanders.

- 2 -

WARNING

POTENTIAL HAZARD

♦

Engine exhaust contains carbon monoxide, which is

an odorless deadly poison.

WHAT CAN HAPPEN

♦

Carbon monoxide can kill you and is also known to the

State of California to cause birth defects.

HOW TO AVOID THE HAZARD

♦

Do not run engine indoors or in a small confined area

where dangerous carbon monoxide fumes can collect.

DANGER

POTENTIAL HAZARD

♦

In certain conditions gasoline is extremely flammable

and highly explosive.

WHAT CAN HAPPEN

♦

A fire or explosion from gasoline can burn you, others,

and cause property damage.

HOW TO AVOID THE HAZARD

♦

DO NOT

smoke while refueling, and stay away from

an open flame or where gasoline fumes may be ignited

by spark.

♦

Refuel only in a well ventilated area, or refuel

outdoors.

♦

Store gasoline in an approved container and keep it

out of the reach of children.

♦

Add fuel before starting the engine.

Never

remove the

cap of the fuel tank or add fuel when engine is running

or when the engine is hot.

♦

Never fill the fuel tank so that the gasoline level rises

above a level that is 1/2” below the bottom of the filler

neck to allow for gasoline expansion and prevent fuel

spillage.

♦

If fuel is spilled,

DO NOT

attempt to start the engine.

Move away from the area of the spill and avoid

creating any source of ignition until fuel vapors have

dissipated.

- 3 -

DANGER

POTENTIAL HAZARD

♦

In certain conditions gasoline is extremely flammable

and highly explosive.

WHAT CAN HAPPEN

♦

A static charge can ignite gasoline vapors. A fire or

explosion from gasoline can burn you, others, and

cause property damage.

HOW TO AVOID THE HAZARD

♦

Purchase and store gasoline only in an approved

container.

♦

Always place gasoline containers on the ground away

from your vehicle before filling.

♦

Do not fill gasoline containers inside a vehicle or on a

truck or trailer bed because interior carpets or plastic

truck bed liners may insulate the container and slow

the loss of any static charge.

♦

When practical, remove gas-powered equipment from

the truck or trailer and refuel the equipment with its

wheels on the ground.

♦

If this is not possible, then refuel such equipment on a

truck or trailer from a portable container, rather than

from a gasoline dispenser nozzle.

♦

If a gasoline dispenser nozzle must be used, keep the

nozzle in contact with the rim of the fuel tank or

container opening at all times until fueling is complete.

1.4 OPERATION

Although hazard control and accident prevention are partially dependent upon the

design and configuration of the equipment, these factors are also dependent upon

the awareness, concern, prudence and proper training of the personnel involved

in the operation, transport, maintenance and storage of the equipment. It is

essential that all Operator Safety Mechanisms be connected and in operating

condition prior to use for mowing.

1.4.1 Give complete, undivided attention to the job at hand.

1.4.2 Mow only in daylight or good artificial light.

Do Not

operate the mower when

children or others are in the area!

1.4.3 When feasible, avoid operating the equipment in wet grass.

1.4.4 Use

EXTREME

caution when mowing and/or turning on slopes as loss of

traction and/or control could occur. Mow

across

slopes with walk behind

mowers, never up and down. Loss of control and/or loss of operator’s footing

could result in a fall with an arm or leg getting under the mower or engine deck

and sustaining serious injury. Drive slower on slopes.

DO NOT

operate on

slopes greater than 20 degrees. Watch for ditches, holes, rocks, dips, and

rises which can cause erratic handlebar movement and loss of footing. Keep

away from drop-offs and steep banks. Avoid sudden starts. Look down and

behind you before and while moving backwards.

DO NOT

mow slopes when

grass is wet - slippery conditions create hazardous footing, affect steering, and

reduce traction and braking. The operator is responsible for safe operation on

slopes. See inside back cover to determine the approximate slope angle of the

area to be mowed.

- 4 -

1.4.5 Stop the blades when crossing surfaces other than grass; and when

transporting the mower to and from the area to be mowed.

1.4.6 Never operate the mower with defective guards, shields, or covers. Always

have safety shields, guards, switches, and other devices in place and in proper

working condition.

1.4.7

Do Not

change the engine governor settings or over-speed the engine.

Operating an engine at excessive speed may increase the hazard of personal

injury.

1.4.8 Place transmission in neutral, disengage blade drive before starting engine.

1.4.9 Start the engine carefully with feet well away from blades.

1.4.10 Keep hands, feet and clothing away from rotating parts while the mower is

being operated.

1.4.11 Stop the engine and remove spark plug wire(s) or ignition key:

•

Before checking, cleaning or working on the mower.

•

After striking a foreign object (inspect the mower for damage and make

repairs before restarting and operating the mower).

1.4.12 Stop the engine:

•

Before clearing blockages.

•

Whenever you leave the mower.

•

Before removing the grass catcher.

•

Before refueling.

•

Before making height adjustments.

1.4.13 Before stopping the engine, return the throttle control to the idle position for 30

seconds to allow the engine to cool down.

1.4.14 The fuel system is provided with a shut-off valve. The fuel shut-off valve is

used to shut off the fuel when:

•

The machine will not be used for a few days.

•

During transport to and from the job.

•

When parking inside a building.

1.4.15 This mower was designed for one operator only. Keep all others away from

mower during operation.

1.4.16

Do Not

mow without the grass deflector or entire grass collection system in

place and in proper working condition.

1.5 MAINTENANCE AND STORAGE

1.5.1 For engine maintenance, follow the engine manufacture’s recommendations

precisely as stated in the engine manual.

1.5.2 When making adjustments while the engine is running, such as carburetor and

motion control linkage adjustments, stand to one side and keep clear of

moving/rotating components, such as engine screen, drive belts and sheaves.

Do Not

wear

loose fitting clothing or jewelry that could get tangled in

moving/rotating components..

1.5.3 Keep engine and engine area free from accumulation of grass, leaves,

excessive grease or oil and other debris which can accumulate in these areas.

These materials can become combustible and may result in a fire.

1.5.4 Store fuel in a container specifically designed for this purpose in a cool, dry

place.

- 5 -

1.5.5 Keep the mower and fuel container in locked storage to prevent children from

playing or tampering with them.

1.5.6 Gasoline powered equipment or fuel containers should not be stored in a

basement or any enclosed area, where open pilot lights or heat appliances are

present.

1.5.7 Maximum mowing results and safety can only be achieved if the mower is

properly maintained and operated correctly.

1.5.8. Check all bolts frequently to maintain proper tightness.

1.5.9. Keep all guards, shields and all safety devices in place and in safe working

condition.

1.5.10 Frequently check for worn or deteriorating components that could create a

hazard.

1.5.11 All replacement parts must be the same as or equivalent to the parts supplied

as original equipment.

1.6 RIDING ATTACHMENTS

1.6.1 Use only

Exmark

riding attachments. The use of other than Exmark riding

attachments may create a hazardous condition resulting in injury.

1.7 SAFETY SIGNS

1.7.1 Keep all safety signs legible. Remove all grease, dirt and debris from safety

signs.

1.7.2 Safety signs must be replaced if they are missing or illegible.

1.7.3 When new components are installed, be sure that current safety signs are

affixed to the replaced components.

1.7.4 New safety signs may be obtained from your authorized Exmark equipment

dealer or distributor or from Exmark Mfg. Co. Inc.

1.7.5 Safety signs may be affixed by peeling off the backing to expose the adhesive

surface. Apply only to a clean, dry surface. Smooth to remove any air bubbles.

1.7.6 Familiarize yourself with the following safety signs and instruction labels. They

are critical to the safe operation of your Exmark commercial mower.

- 6 -

14 HP Kawasaki,Briggs & Stratton, & 15HP Kohler – All Serial Nos.

(Serial Nos. 150,000-189,999: 17 HP Kawasaki

PART NO. 323688

LOCATION: Console

14 HP Kawasaki & 15HP Kohler

PART NO. 323689

LOCATION: RH Side of

Console

Serial Nos. 190,000 & Higher 15 & 17 HP Kawasaki

PART NO. 323699

LOCATION: Console

15 & 17 HP Kawasaki

PART NO. 323691

LOCATION: RH Side of

Console

PART NO. 403005

LOCATION: RH & LH Corners

of Mower Deck

PART NO. 303508

LOCATION: Front of Mower

Deck, Top Surface

PART NO. 303293

LOCATION: On Top RH Side

of Fuel Tank

17HP Kawasaki & 16HP B&S

Serial Nos. 150,000-189,999

PART NO. 403120

LOCATION: On Switch Bracket

at Front Left of

Fuel Tank Support

- 7 -

PART NO. 403143

LOCATION: RH Side of Rear

Surface of Engine Deck

PART NO. 303517

LOCATION: LH Side of Rear

Surface of Mower Deck

PART NO. 553049

LOCATION: Front of Mower Deck Top Surface

PART NO. 513746

LOCATION: On Engine Blower

Housing next to

Muffler & on Center

Belt Cover

PART NO. 323540

LOCATION: Front of Mower Deck

Top Surface

PART NO. 323550

LOCATION:Upper

Handle

PART NO. 303518

LOCATION: Transmission Shifter Plate

PART NO. 413421

LOCATION: Left Rear on Top of

Engine Deck

16 HP Briggs & Stratton

PART NO. 543631

LOCATION: RH Side Console

- 8 -

2. SPECIFICATIONS

2.1 MODEL NUMBER:

Serial Nos. 150,000 – 189,999:

MHP4816BV; MHP5216BV

Serial Nos. 150,000 – 219,999:

MHP3614KA; MHP4814KA

Serial Nos. 150,000 & Higher:

MHP3615KC; MHP4815KC

Serial Nos. 160,000 & Higher:

MHP4817KA; MHP5217KA

Serial Nos. 190,000 & Higher:

MHP4815KA

Serial Nos. 220,000 & Higher:

MHP3615KA

2.2 ENGINE

2.2.1 Engine Specifications: See your Engine Owner's Manual.

2.2.2 3600 RPM (No Load).

2.3 FUEL SYSTEM

2.3.1 Capacity: 5.0 gal.(18.9 L.)

2.3.2 Type of Fuel: Regular

unleaded

gasoline, 87 octane or higher. In countries

using the research method, it should be a 90 octane

minimum

2.3.3 Fuel Filter: Replaceable in-line

2.3.4 Fuel Shut-Off Valve: 1/4 turn

2.4

SAFETY INTERLOCK SYSTEM

Operator must have transmission in neutral and blade clutch disengaged to

start engine. Release of OPC levers will cause the engine to stop if

transmission is

not

in neutral

and/or

blade clutch is

engaged

2.5 STEERING/BRAKE CONTROL:

Fingertip drive control levers provide independent speed control, braking and

neutral to each drive wheel for moving, stopping and power turning. Parking

brakes are engaged by locking drive control levers in the “brake” position.

2.6 TRANSMISSION:

2.6.1 Peerless 700-061, five speeds forward and one reverse.

2.6.2 Speed Range:

2.0 mph (3.22 km/h) 4

4.1 mph (6.60 km/h)

2.7 mph (4.35 km/h) 5

6.2 mph (9.98 km/h)

3.5 mph (5.63 km/h) Rev. 3.1 mph (4.99 km/h)

PART NO. 413206

LOCATION: Top of Cutter Deck, Under

Center Belt Shield (36”)

PART NO. 413327

LOCATION: Top of Cutter Deck, Under

Belt Shield (48” & 52” Decks)

- 9 -

2.7 WHEEL DRIVE SYSTEM:

Banded double A-Section V-Belts, single top side idlers and replaceable bolt-

on drive sheaves and brake drums.

2.8 TIRES

Drive Front Caster

Size16 x 6.50-8......9 x 3.50-4

Quantity............................. 2.........................................2

Tread................Turf Saver/Turf Master..................Smooth

Ply Rating.......................... 4.........................................4

Pressure............... 14 psi(97 kPa)..................22 psi(152 kPa)

2.9 Deck

2.9.1 Cutting Width:

Model 36 in....................35.25 in. (89.5 cm)

Model 48 in....................47.25 in. (120.0 cm)

Model 52 in....................52.00 in. (132.1 cm)

2.9.2 Discharge: Right Side

2.9.3 Blade Size:

Model 36 in....................18.00 in. (45.7 cm) ..............Qty. 2

Model 48 in....................16.25 in. (41.3 cm) ..............Qty. 3

Model 52 in....................18.00 in. (45.7 cm) ..............Qty. 3

2.9.4 Type of Drive: Manual engagement of belt with over-center lock. Belt tension

is adjustable via turnbuckle.

2.9.5 Deck Mounting: Full floating deck is attached to out-front support frame,

removable for service.

2.9.6 Cutting Height: Adjusts in 1/2” (.63 cm) increments from 1.5” (3.8 cm) to 4 1/2”

(11.4 cm).

2.10 DIMENSIONS

2.10.1 Overall Width:

36” 48” 52”

Discharge chute down

46.25” 58.25” 62.6”

(117.5 cm) (148.0 cm) (159.0 cm)

Discharge chute up

36.1” 48.1” 53.0”

(Transport only)

(91.7 cm) (122.2 cm) (134.62 cm)

2.10.2 Overall Length:

36” 48” 52”

Overall Length

77.7” 73.7” 75.9”

(197 cm) (187 cm) (193 cm)

2.10.3 Curb Weight:

36” 48” 52”

Curb Weight

∗

507 lbs. 555 lbs. 583 lbs.

(230 kg) (252 kg) (264 kg)

∗

Weights will vary slightly depending on engine option.

2.10.4 Overall Height: 42” (107 cm)(all units)

2.10.5 Tread Width (to outside of tires):

36” Model....................35.2” (89.4 cm)

48” Model....................35.2” (89.4 cm

52” Model....................35.2” (89.4 cm)

- 10 -

2.11 TORQUE REQUIREMENTS

BOLT LOCATION TORQUE

Blade Mounting Bolt.........................................................75-80 ft-lbs.

Cutter Housing Spindle Nut..............................................75-80 ft-lbs.

Anti-Scalp Roller Bolts......................................................40-45 ft-lbs.

Mower Deck Support/Engine Deck Mount........................30-35 ft-lbs.

Engine Mounting Bolts

Briggs

Stratton

& 15 &

Kawasaki..........15-20 ft-lbs.

Kohler

HP Kawasaki..................................25-30 ft-lbs.

Transmission Shifter-lever Nut...........................30-35 ft-lbs.

3. ASSEMBLY INSTRUCTIONS

3.1 Uncrate unit, and remove upper handle assembly, fuel tank, and linkages from

top of crate.

3.2 Remove and open the bolt bag.

3.3 Loosen the 5/16" hardware at the two (2) discharge deflector hinge points so

that the deflector is snug, but can be moved up and down freely.

3.4 Refer to Parts Manual to help you identify and locate parts and their proper

position.

3.5 Apply retaining adhesive “Fel-Pro Retaining I or Retaining II” or “Loctite RC609

or 680” on the two threaded studs from the bolt bag and install into the two left

holes underneath fuel tank. Install the fuel tank on top of the fuel tank support

with the studs going through the slots in the support. Install two 5/16-18 x 3/4”

screws with a 5/16” SAE flatwasher and 5/16” lockwasher into the threaded

holes in the right side of the fuel tank.

Do not over tighten

. Place a 5/16” SAE

flatwasher, then a spring, over each of the studs and fasten with a 5/16 nyloc

nut. Tighten 3/16 nylock nut fully then cack off a 1/2 turn. This is to allow for

normal fuel tank expansion with changes in temperature and fuel levels.

3.6 Attach the fuel tank hose to the tank fitting and secure with the clamp provided.

Make sure that fuel hose is not between engine and throttle plate on engine.

3.7 Position the lower end of the handle assembly on the outside of the upper rear

section of the fuel tank & handle support. Install four 3/8-16 x 1" bolts (with

four spring disk washers against the head of each bolt) from the outside in.

Secure using four 3/8" whizlock nuts on the inside of each handle support and

tighten until the spring disk washers are flat (See Figure 1).

FIG. 1

UPPER HANDLE MOUNTING

3.8 Route the throttle cable along the right side of the upper handle, under the fuel

tank support, and position the cable on the

left

side of the engine

(Kaw &

Kohler)

to the

right side

of engine

(B&S)

Attach throttle cable to engine:

For Kohler and Kawasaki engines with “positive” detents in throttle cable

for the full throttle and idle positions.

- 11 -

a) Position the throttle control lever (on console) in the full throttle (but not

choke) position. You will feel a detent when the throttle lever is

approximately 3/4” from the upper end of the slot (this is full throttle

position).

b) Loosen clamp on engine control plate (See Figures 2, 3 & 4). Attach inner

wire of the throttle cable to the control plate lever and position cable clamp,

do not

tighten clamp.

FIG 2

KOHLER SPEED CONTROL

(THROTTLE CABLE HOOK-UP)

FIG 3

14 HP KAWASAKI SPEED CONTROL

(THROTTLE CABLE HOOK-UP)

FIG 4

15 & 17 HP KAWASAKI SPEED CONTROL

(THROTTLE CABLE HOOK-UP)

Control Alignment Holes

Control Plate Lever

Choke Link

Clamp

Control Cable

Choke Adjusting Screw

- 12 -

c) Pull cable upward (pull the cable to the right when facing the control plate

on 15 & 17 HP Kawasaki units) until alignment holes in control plate lever

and control plate line up. For Kawasaki 15/64” (6mm) drill bit can be

inserted through these two holes to align them. For Kohler use a 19/64” drill

bit. Once the holes are aligned, tighten clamp onto throttle cable.

d) Be sure the

choke adjusting screw just contacts the choke lever

when

the throttle control is in the full throttle position. Choke link should not move

when throttle control is moved to the full throttle position. Choke must be

completely closed when throttle lever is moved to the full forward “CHOKE”

position.

e) This step needs to be done after the

unit has been assembled and the

engine has been started

. Refer to Section 4. (Operation Instructions).

For Kohler and 14 HP Kawasaki engines

Check the engine “STOP” position by moving the throttle control fully to the

rear. (Note: There is a detent toward the lower end of the slot in the

console for “IDLE”; the “STOP” position is rearward from this detent).

For Kohler engines

If the engine continues to run in the "STOP" position, turn the kill switch

adjusting screw inward until engine stops, then give it an additional 1/2 to

3/4 turn to assure it will always function properly.

(The 14 HP Kawasaki kill switch is not adjustable)

For 15 & 17 HP Kawasaki engines

There is not a “STOP” position. The engine will continue to run when the

throttle control is moved past the rear detent.

Turn the ignition switch to the “off” position to stop the engine.

For B&S Vanguard Engines:

a) Position the throttle control lever (on console) 1/8" from the upper end of

the slot. Route the throttle cable along the right side of the upper handle,

under the fuel tank support, and position the cable on the

right

side of the

engine between the oil fill tube and engine.

b) Attach the inner wire to the appropriate throttle control lever on the engine.

Loosen the cable clamp on the engine, place the cable behind it and pullup

on the cable to move the throttle linkage to the

full

throttle

position.

Tighten the cable clamp screw.

3.9 Connect the blade engagement linkages. Loosen jamnut and remove

turnbuckle from lower linkage. Screw turnbuckle onto both upper and lower

linkages simultaneously. (See figure 5) Note that the threads on upper linkage

are left hand. See 5.2.2 for linkage adjustment.

- 13 -

FIG 5

BLADE ENGAGEMENT LINKAGE

3.10 Install and adjust shifter lever.

a) Remove the 3/8” nyloc nut and spring disc washer from the stud on top of

the transmission. Install the shifter lever through slot in shifter lever plate

and onto the stud on top of transmission. Be sure the square-hole washer

remains between the lever and transmission. Replace the spring disc

washer and nyloc nut(see figure 6). Torque the 3/8” nut to 35ft. lbs.

(47N.M).

b) Shift lever to second gear and check alignment of lever in slot of shifter

plate. Clearance between top of lever and the top of the slot should be

about equal to the clearance between bottom of the lever and the bottom

of the slot (See figure 7). If it is not, remove lever and bend it slightly to

adjust. DO NOT Bend lever while it is attached to transmission. Reinstall

lever and tighten hardware.

c) Shift to neutral position. Lever Should not contact the left edged of the

upper slot. Push lever down. Lever should not contact the right edge of

the bottom slot (See Figure 8). Shifter plate can be adjusted side to side

to adjust position of lever relative to the slot in plate. Loosen the two

bolts securing the shifter plate to the shifter lever legs. Adjust shifter

plate and retighten bolts.

FIG. 7

THIS CLEARANCE SHOULD BE EQUAL

FIG. 6

SHIFTER LEVER

TO TRANSMISSION

- 14 -

FIG. 8

THIS CLEARANCE SHOULD BE EQUAL

3.11 Install and adjust wheel drive linkages.

a) Screw threaded end of drive linkages into swivels in wheel drive idler arms.

b) Insert clevis pin from bolt bag through drive linkage, lever and slot in the

neutral lock/park brake latches (See Figure 9). Make proper adjustments

before adding hairpins.

FIG. 9

LEVER AND ROD ADJUSTMENT

c) Adjust drive linkage length by threading into or out of the swivel until

there is a 3/16” to 1/4” clearance between the linkage assembly and the

bottom of the slot in the neutral lock/park brake latch. (See Figure 10)

FIG. 10

NEUTRAL LOCK LEVER CLEARANCE

Note: Neutral lock/park brake latch clearance should be checked when

there is a slight upward force placed on the drive levers to remove any

“slack” in the linkage.

After clevis pin has been inserted, install hairpin into hole on the clevis pin

between the neutral lock/park brake latch and drive lever (See Figure 11).

Repeat procedure on opposite side of unit.

Clevis Pin

Drive Linkage

Neutral Lock/Park Brake Latch

Drive Lever

1/4” Clearance

3/16” TO 1/4”

Drive Linkage

Neutral Lock/ Park

Brake Latch

- 15 -

FIG. 11

DRIVE LEVER HARDWARE LOCATION

d) Adjust brakes by adjusting wingnut on upper end of each brake rod so

that when brakes are engaged there is approximately 1/4” of clearance

between ends of drive levers and handle grips (See Figure 10)

Note: Adjustment should allow the brakes to be engaged, yet allow the

neutral lock/park brake latches to be moved into the park brake position,

if not the brake linkages must be adjusted again.

e) Squeeze the drive levers and move both neutral lock/park brake latches

into the neutral lock position. Mower should move forward and backward

freely, if not, readjust as stated in Sections 3.11c and 3.11d.

3.12 Route the long unattached wiring harness lead, up the left hand side of the

handle and connect the two terminals (in any order) to the operator presence

control switch terminals underneath the control console.

Fasten the lead to the handle with two small wire ties from the bolt bag, one at

the upper end of the handle next to the console, and one at the very lower end

of the handle where it attaches to the fuel tank support.

3.13 If machine is shipped without muffler installed, install muffler with hardware

provided.

3.14 For Briggs and Stratton Engines install debris guard to top of engine.

3.15 Service Engine: Refer to Engine Owner’s Manual.

3.16

GREASE UNIT: NOTE:

UNIT IS NOT GREASED AT THE FACTORY.

Refer to 5.1.13, for locations and grease amounts.

3.17 Follow pre-start instructions as outlined in 4.2.

3.18 Perform any needed adjustments as outlined in the Adjustment Section.

4. OPERATION INSTRUCTIONS

4.1 Controls

4.1.1 Operator Presence Control (OPC) Levers: Located on the upper handle

assembly directly above the handle grips.

When these levers are depressed,

the OPC system senses that the operator is in the normal operator's

position.

When the levers are released, the OPC system senses that the

operator has moved from the normal operating position

and will kill the

engine if either the transmission shift lever is

not in the neutral

position or the

blade clutch is engaged

4.1.2 Drive Levers: Located on each side of the upper handle assembly directly

below the handle grips. These levers individually control the clutching action of

the wheel drive belts and brakes. When the drive levers are all of the way

down, the wheel drive belts engage and the brakes disengage. Squeezing the

left or right hand drive lever causes the left hand or right hand wheel to slow

down or stop, which makes the machine turn to the left or right respectively.

Drive Linkage

Left Side

Shown

Reference for

Position Only

Neutral

Lock/Park

Brake Latch

Drive

Lever

Clevis Pin

Hairpin

Page is loading ...

Exmark Metro HP MHP4815KA User manual

Brand: Exmark

Model: Metro HP MHP4815KA

Category: Lawnmowers

Type: User manual

Download PDF

report

Exmark Metro HP MHP4815KA User manual

Exmark Metro HP MHP4815KA User manual

Related papers

Other documents