DVD Player
DVD-P180
www.samsung.com/my
AK68-01640C
2
PRECAUTIONS
PRECAUTIONS
1. Setting up
- Refer to the identification label located on
the rear of your player for its proper operat-
ing voltage.
- Install your player in a cabinet with ade-
quate ventilation holes. (7~10cm) Do not
block ventilation holes on any of the compo-
nents for air circulation.
- Do not push the disc tray in by hand.
- Do not stack components.
- Be sure to turn all components off before
moving the player.
- Before connecting other components to this
player, be sure to turn them off.
- Be sure to remove the disc and turn off the
player after use, especially if you don’t use
it for a long time.
- The mains plug is as a disconnect device
and shall stay readily operable at any time.
2. For your safety
- This product utilizes a laser. Use of controls
or adjustments or performance of proce-
dures other than those specified herein may
result in hazardous radiation exposure.
- Do not open covers and do not repair your-
self. Refer servicing to qualified personal.
3. Caution
- Your player is not intended for industrial use
but for domestic purposes. Use of this prod-
uct is for personal use only.
- Apparatus shall not be exposed to dripping
or splashing and no objects filled with liq-
uids, such as vases, shall be placed on the
apparatus.
- Exterior influences such as lightning and
static electricity can affect normal operation
of this player. If this occurs, turn the player
off and on again with the POWER button, or
disconnect and then reconnect the AC
power cord to the AC power outlet. The
player will operate normally.
- When condensation forms inside the player
due to sharp changes in temperature, the
player may not operate
correctly. If this occurs, leave the player at
room temperature until the inside of the
player becomes dry and operational.
4. Disc
- Do not clean record-cleaning sprays, ben-
zene, thinner, or other volatile solvents that
may cause damage to the disc surface.
- Do not touch the disc’s signal surface. Hold
by the edges or by one edge and the hole
in the center.
- Wipe the dirt away gently; never wipe a
cloth back and forth over the disc.
5. Environmental info
- The battery used in this product contains
chemicals that are harmful to the environ
ment.
- So, dispose of batteries in the proper man
ner, according to federal, state, and local
regulations.
The product unit accompanying this user manual is
licensed under certain intellectual property rights of
certain third parties. This license is limited to private
non-commercial use by end-user consumers for
licensed contents. No rights are granted for
commercial use. The license does not cover any
product unit other than this product unit and the
license does not extend to any unlicensed product
unit or process conforming to ISO/OUR 11172-3 or
ISO/OUR 13818-3 used or sold in combination with
this product unit. The license only covers the use of
this product unit to encode and/or decode audio files
conforming to the ISO/OUR 11172-3 or ISO/OUR
13818-3. No rights are granted under this license for
product features or functions that do not conform to
the ISO/OUR 11172-3 or ISO/OUR 13818-3.
CAUTION: USE OF ANY CONTROLS,
ADJUSTMENTS, OR PROCEDURES OTHER
THAN SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
3
BEFORE
BEFORE
YOU
YOU
ST
ST
AR
AR
T
T
English
1. Open the battery cover on the back of the remote
control.
2. Insert two AAA batteries.
Make sure that the
polarities (+ and -) are aligned correctly.
3. Replace the battery cover.
Remote Control
User’s Manual
Video/Audio
Cable
Install Batteries in the Remote control
If remote control doesn’t operate
properly:
- Check the polarity + - of the batteries (Dry-Cell)
- Check if the batteries are drained.
- Check if remote control sensor is blocked by
obstacles.
- Check if there is any fluorescent lighting nearby.
Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Before you start . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Setup
General Features . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Disc Type and Characteristics . . . . . . . . . . . . . . . . 5
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Tour of the Remote Control . . . . . . . . . . . . . . . . . . 8
Connections
Choosing a Connection . . . . . . . . . . . . . . . . . . . . . 9
Basic Functions
Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Using the Search and Skip Functions . . . . . . . . . 13
Using the Display Function . . . . . . . . . . . . . . . . . 13
Using the Disc and Title Menu . . . . . . . . . . . . . . 14
Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Slow Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Advanced Functions
Adjusting the Aspect Ratio (EZ View) . . . . . . . . . 15
Selecting the Audio Language . . . . . . . . . . . . . . . 15
Selecting the Subtitle Language. . . . . . . . . . . . . . 16
Changing the Camera Angle . . . . . . . . . . . . . . . . 16
Using the Bookmark Function . . . . . . . . . . . . . . . 16
Using the Zoom Function . . . . . . . . . . . . . . . . . . . 17
Clips Menu for MP3/WMA/JPEG/
CD Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Folder Selection . . . . . . . . . . . . . . . . . . . . . . . . . . 17
MP3/WMA/CD Audio Playback. . . . . . . . . . . . . . . 17
Picture CD Playback. . . . . . . . . . . . . . . . . . . . . . . 18
Changing Setup Menu
Using the Setup Menu . . . . . . . . . . . . . . . . . . . . . 19
Setting Up the Language Features . . . . . . . . . . . 20
Setting Up the Audio Options . . . . . . . . . . . . . . . . 21
Setting Up the Display Options . . . . . . . . . . . . . . 21
Setting Up the Parental Control . . . . . . . . . . . . . . 22
Reference
Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . 24
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
T
T
ABLE OF
ABLE OF
CONTENT
CONTENT
4
SETUP
SETUP
General Features
Excellent Sound
Dolby Digital, a technology developed by Dolby
Laboratories, provides crystal clear sound reproduc-
tion.
Screen
Both regular and widescreen(16:9) pictures can be
viewed.
Slow Motion
An important scene can be viewed in slow motion.
Parental Control (DVD)
The parental control allows users to set the level
necessary to prohibit children from viewing harmful
movies such as those with violence, adult subject
matter, etc.
Various On-Screen Menu Functions
You can select various languages (Audio/Subtitle)
and screen angles while enjoying movies.
EZ VIEW (DVD)
Easy View enables picture adjustment to match
your TV's screen size (16:9 or 4:3).
Digital Photo Viewer (JPEG)
You can view Digital Photos on your TV.
Repeat
You can repeat a song or movie simply by pressing
the REPEAT button.
MP3/WMA
This unit can play discs created from MP3/WMA
files.
Note
- Discs which cannot be played with this
player.
• DVD-ROM • DVD-RAM
• CD-ROM • CDV
• CDI • CVD
• CDGs play audio only, not graphics.
- Ability to play back may depend on recording
conditions.
• DVD-R, +R
• CD-RW
• DVD+RW, -RW (V mode)
- The unit may not play certain CD-R, CD-RW
and DVD-R due to the disc type or recording
conditions.
COPY PROTECTION
Many DVD discs are encoded with copy protection.
Because of this, you should only connect your DVD
player directly to your TV, not to a VCR. Connecting
to a VCR results in a distorted picture from copy-
protected DVD discs.
This product incorporates copyright protection
technology that is protected by methods claims of
certain U.S. patents and other intellectual property
rights owned by Macrovision Corporation and other
rights owners. Use of this copyright protection tech-
nology must be auzthorized by Macrovision
Corporation, and is intended for home and other
limited viewing uses only unless otherwise autho-
rized by Macrovision Corporation. Reverse engi-
neering or disassembly is prohibited.
5
English
Disc Type and Characteristics
Disc Markings
Region Number
Both the DVD player and the discs are coded
by region. These regional codes must match in
order for the disc to play. If the codes do not
match, the disc will not play.
The Region Number for this player is
described on the rear panel of the player.
You must only insert one DVD disc at a
time. Inserting two or more discs will not
allow to play them back and it may cause
damage to the DVD player.
~
DIGITAL
SOUND
STEREO
PAL
Play Region Number
PAL broadcast system in
U.K, France, Germany, etc.
Dolby Digital disc
Stereo disc
Digital Audio disc
DTS disc
MP3 disc
This DVD player is capable of playing the following types of discs with the correspond-
ing logos:
12 Cm
8 Cm
Single-sided 240 min.
Double-sided 480 min.
Single-sided 80 min.
Double-sided 160 min.
Audio
+
Video
- DVD contains excellent sound
and video due to Dolby Digital
and MPEG-2 system.
- Various screen and audio func-
tions can be easily selected
through the on-screen menu.
Disc Types (Logos)
Recording Types Disc Size Max. Playing Time Characteristics
DVD
12 Cm
8 Cm
74 min.
20 min.
Audio
+
Video
- Video with CD sound, VHS quali-
ty & MPEG-1 compression tech-
nology.
VIDEO-CD
12 Cm
8 Cm
74 min.
20 min.
Audio
- CD is recorded as a Digital
Signal with better audio quality,
less distortion and less deteriora-
tion of audio quality over time.
AUDIO-CD
6
Description
Front Panel Controls
1. STANDBY/ON ( )
When STANDBY/ON is pressed on, the indicator
goes out and the player is turned on.
2. STANDBY indicator
When the unit is first plugged in, this indicator
lights.
3. DISC TRAY
Place the disc here.
4. REMOTE CENSOR
5. OPEN/CLOSE /STOP ( )
Stops disc play.
Press to open and close the disc tray.
6. PLAY/PAUSE ( )
Begin or pause disc play.
1
6
3
2
4
5
7
English
Rear Panel
1. AUDIO OUT JACKS
- Connect to the Audio input jacks of your television or
audio/video receiver.
2. VIDEO OUT JACK
- Use a video cable to connect to the Video input jack
on your television
.
3. DIGITAL AUDIO OUT JACKS
- Use either coaxial digital cable to connect to a com-
patible Dolby Digital receiver.
- Use either coaxial digital cable to connect to an A/V
Amplifier that contains a Dolby Digital, MPEG2 or
DTS decoder.
Note
- See pages 21-22 to get more information on how to use the setup menu.
1
2
3
8
Tour of the Remote Control
1
2
3
4
5
6
7
8
9
10
14
11
12
13
15
16
17
18
19
20
6. SEARCH Buttons (
/
)
Allow you to search forward/backward through a disc.
7. VIDEO SEL.Button
(Only for DVD-P181/DVD-P181K)
8. SKIP Buttons (
/
)
Use to skip the title, chapter or track.
9. STOP Button ( )
10. MENU Button
Brings up the DVD player’s menu.
11. ENTER/
/
,
¦¦
/
Buttons
This button functions as a toggle switch.
12. EZ VIEW Button
The aspect ratio of a picture can easily be adjusted
according to the screen size of your TV (16:9 or 4:3)
13. DISC MENU Button
Brings up the Disc menu.
14. OPEN/CLOSE ( ) Button
To open and close the disc tray
15. AUDIO Button
Use this button to access various audio functions on a disc.
16. DVD Button
Use to operate DVD
17. TV Button
Use to operate TV.
18. BOOKMARK (Number 9 Button)
Quickly find bookmark sections of a DVD
19. STEP /TV SOURCE Button
Advances play one frame at a time.
20. TV CH Buttons
Use to change channel.
21. SUBTITLE Button
22. PLAY/PAUSE Button ( )
Begin/Pause disc play.
23. RETURN Button
Returns to a previous menu.
24. INFO Button
Displays the current disc mode.
25. CANCEL Button
Use to remove menus or status displays from the
screen.
26. REPEAT A-B Button
Allows you to repeat A-B disc.
27. REPEAT Button
Allows you to repeat play a title, chapter, track, or disc.
21
24
23
22
25
26
27
1. DVD Power Button
Turns the power on or standby.
2. NUMBER Buttons
3. TITLE MENU (number 7) Button
Brings up the Title menu.
4. ZOOM/- /-- Button
Enlarge DVD Picture
Use this button to select the channel of TV pro-
gram by inserted the channel number (TV mode).
5. TV VOLUME
TV VOL(+,-) button
9
CONNECTIONS
CONNECTIONS
English
Choosing a Connection
The following shows examples of connections commonly used to connect the DVD player with a TV and
other components.
Before Connecting the DVD Player
- Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.
- Refer to the user’s manual of the additional components you are connecting for more information on those
particular components.
Connection to a TV (For Video)
1
Using video/audio cable, connect the VIDEO
(yellow)/Audio (red and white) terminals on the rear of the
DVD player to the VIDEO (yellow)/Audio (red and white)
IN terminals of TV.
2
Turn on the DVD player and TV.
Note
- Noise may be generated if the audio cable is too close to the power cable.
- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 10 to 11)
- The number and position of terminals can vary depending on your TV set. Please refer to the user's man-
ual of the TV.
RED
WHITE
YELLOW
RED
WHITE
YELLOW
Audio Cable
Video Cable
3
Press the TV/VIDEO button on the TV's remote
control to select Video.
10
Connection to an Audio System (2 Channel Amplifier)
1
Using the audio cables, connect the AUDIO (red and
white) OUT on the rear of the DVD player to the AUDIO
(red and white) IN terminals of the Amplifier.
2
Using the video signal cable, connect the VIDEO terminals
on the rear of the DVD player to the VIDEO terminal of your
TV.
3
Turn on the DVD player, TV, and Amplifier.
4
Press the input select button of the Amplifier to select exter-
nal input in order to hear sound from the DVD player.
Note
- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause
damage to the speakers and your ears.
- Please set the audio in the menu screen according to the Amplifier. (See pages 21)
- The position of terminals can vary depending on the Amplifier.
Please refer to the user's manual of the Amplifier.
RED
WHITE
RED
WHITE
Audio Cable
11
English
Connection to an Audio System (Dolby digital, MPEG2 or DTS Amplifier)
1
If using a coaxial cable (not included), connect the DIGI-
TAL AUDIO OUT (COAXIAL) terminal on the rear of the
DVD player to the DIGITAL AUDIO IN (COAXIAL) termi-
nal of the Amplifier.
2
Using the video signal cable, connect the VIDEO terminals
on the rear of the DVD player to the VIDEO terminal of TV.
3
Turn on the DVD player, TV, and Amplifier.
4
Press the input select button of the Amplifier to select
external input in order to hear sound from the DVD player.
Note
- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause
damage to the speakers and your ears.
- Please set the audio in the menu screen according to the Amplifier. (See pages 21)
- The position of terminals can vary depending on the Amplifier.
Please refer to the user's manual of the Amplifier.
Coaxial cable
(not supplied)
12
BASIC
BASIC
FUNCTIONS
FUNCTIONS
Playing a Disc
Before Play
- Turn on your TV and set it to the correct Video
Input by pressing TV/VIDEO button on the TV
remote control.
- If you connected an external Audio System, turn
on your Audio System and set it to the correct
Audio Input.
After plugging in the player, the first time you press the DVD
POWER button, this screen comes up: If you want to select
a language, press a NUMBER button. (This screen will only
appear when you plug in the player for the first time.)
If the language for the startup screen is not set, the settings
may change whenever you turn the power on or off.
Therefore, make sure that you select the language you want
to use.
Once you select a menu language, you can change it by
pressing the button on the front panel of the unit for
more than 5 seconds with no disc in the unit. Then the
SELECT MENU LANGUAGE window appears again where
you can reset your preferred language.
SELECT MENU LANGUAGE
Playback
1. Press the OPEN/CLOSE ( ) button. The STANDBY
indicator light goes out and the tray opens.
2. Place a disc gently into the tray with the disc’s label facing
up.
- You must only insert one DVD disc at a time.
Inserting two or more discs will not allow to play
them back and it may cause damage to the DVD
player.
3. Press the PLAY/PAUSE ( ) button or OPEN/ CLOSE
()button to close the disc tray.
-
When you stop disc play, the player remembers
where you stopped, so when you press
PLAY/PAUSE ( ) button again, it will pick up where
you left off. (unless the disc is removed or the player
is unplugged, or if you press the STOP ( ) button
twice.)
4. Stopping Play
Press the STOP ( ) button during play.
5. Removing Disc
Press the OPEN/CLOSE ( ) button.
6. Pausing Play
Press the PLAY/PAUSE ( ) or STEP button on the
remote control during play.
- Screen stops, no sound.
To resume, press the PLAY/PAUSE ( )
button once again.
7. Step Motion Play (Except CD)
Press the STEP button on the remote control during play.
- Each time the button is pressed, a new frame will
appear.
- No sound is heard during STEP mode.
- Press the PLAY/PAUSE ( ) button to resume
normal play.
- You can only perform step motion play in the
forward direction.
8. Slow Motion Play
Press SEARCH ( ) button to choose
the play speed between 1/2, 1/4, 1/8 and 1/16 of normal
during PAUSE mode.
- No sound is heard during slow mode.
- Press the PLAY/PAUSE ( ) button to resume
normal play.
- Reverse slow motion play will not work.
Note
- If the player is left in the stop mode for more
than one minute without any user interaction, a
screen saver will be activated. Press the
PLAY/PAUSE ( ) button to resume normal play.
- If the player is left in the stop mode for more than
about 30 minutes, the power will automatically
shut off. (Automatic Power-Off Function)
- If the player is left for about 5 minutes in pause
mode, it will stop.
- This ( ) icon indicates an invalid button press.
Press 1 for English
Touche 2 pour Français
Drücken Sie 3 für Deutsch
Pulsar 4 para Español
Premere 5 per Italiano
Druk op 6 voor Nederlands
13
English
Using the Search and Skip
Functions
During play, you can search quickly through a chap-
ter or track, and use the skip function to jump to the
next selection.
Searching through a Chapter or
Track.
During play, press the SEARCH ( or ) button on
the remote control.
Note
- The speed marked in this function may be different from
the actual speed of playback.
- No sound is hearing during search mode (Except CD).
Skipping Tracks
During play, press the SKIP ( or ) button.
- When playing a DVD, if you press the SKIP ( ) button, it
moves to the next chapter. If you press the SKIP ( )
button, it moves to the beginning of the chapter. One more
press makes it move to the beginning of the previous
chapter.
- When playing a CD, in Menu Off mode, if you press the
SKIP ( ) button, it moves to the next track. If you
press the SKIP ( ) button, it moves to the beginning of
the track. One more press makes it move to the begin
ning of the previous track.
Using the Display Function
When Playing a DVD/VCD
1. During play, press the INFO button on the remote control.
Using the Disc and Title
Menu
Using the Disc Menu
1. Press the MENU button on the remote control.
2. Press the / buttons to select Disc Menu, then press the
or ENTER button.
2. Press the /buttons to select the desired item.
3. Press the ¦/ buttons to make the desired setup and then
press the ENTER button.
- You may use the number buttons of the remote control
to directly access a title, chapter or to start the
playback from the desired time.
Note
To access the desired title when there is
more than one in the disc. For example, if
there is more than one movie on a DVD,
each movie will be identified.
Most DVD discs are recorded in chapters so
that you can quickly find a specific passage
Allows playback of the film from a desired
time. You must enter the starting time as a
reference.The time search function does not
operate on some disc.
Refers to the language of the film soundtrack.
In the example, the soundtrack is played in
English 5.1CH. A DVD disc can have up to
eight different soundtracks.
Refers to the subtitle languages available in
the disc. You will be able to choose the
subtitle languages or, if you prefer, turn them
off from the screen. A DVD disc can have up
to 32 different subtitles.
To access the desired Bookmark or Angle
function.
Some DVD discs are have more angle func-
tion from any picture.
Bookmark function make you easily and
quickly to find a track or chapter from DVD.
4. To make the screen disappear, press the RETURN button
again.
.. Language Setup Page ..
Player Menu ENG
Disc Menu ENG
Audio ORI
Subtitle AUTO
Note
- Depending on a disc, the Disc Menu may not work.
- You can also use the Disc Menu, using the DISC
MENU button on the remote control.
DVD
VCD
CD
2X, 4X, 64X, 128X
4X, 8X
2X, 4X, 8X
14
T
-
-
-
Repeat Play
Press the REPEAT button to change playback
mode.
When playing a DVD/VCD
- DVD repeat play by chapter,title,disc
repeat play by disc or track.
- Chapter : repeats the chapter that is playing.
- Title : repeats the title that is playing.
- Disc : repeats the disc that is playing.
- Track : repeats the track that is playing.
- Off
Not
- A-B REPEAT allows you to set point(B) directly
after point (A) has been set.
- Depending on a disc, the Repeat function may
not work.
Slow Play
This feature allows you slowly to repeat scenes con-
taining sports, dancing, musical instruments being
played etc., so you can study them more closely.
When playing a DVD
1. During play, press the PLAY/PAUSE ( ) button.
2. Press the SEARCH (
)
button repeatedly to choose
the play speed between 1/2, 1/4,1/8,1/16 of normal during
PAUSE mode.
Using the A-B Repeat function
1. Press the REPEAT A-B button on the remocon at the point
where you want repeat play to start (A).
2. Press the REPEAT A-B button on the remocon at the
point where you want the repeat play to stop (B).
3. To return to normal play, press REPEAT A-B button
again.
DVD/VCD
15
English
ADV
ADV
ANCED
ANCED
FUNCTIONS
FUNCTIONS
Adjusting the Aspect Ratio
(EZ View)
To play back using aspect ratio
(DVD)
Press the EZ VIEW button.
- The screen size changes when the button is pressed
repeatedly.
- The screen zoom mode operates differently depending on the
screen setting in the Display Setup menu.
- To ensure correct operation of the EZ VIEW button, you
should set the correct aspect ratio in the Display Setup
menu. (See pages 21 to 22).
If you are using a 16:9 TV
For 16:9 aspect ratio discs
- WIDE SCREEN
Displays the content of the DVD title in 16:9 aspect ratio.
- SCREEN FIT
The top and bottom portions of the screen are cut off.
When playing a 2.35:1 aspect ratio disc, the black bars at
the top and bottom of the screen will disappear. The picture
will look vertically stretched. (Depending on a type of disc,
the black bars may not disappear completely.)
- ZOOM FIT
The top, bottom, left and right of the screen are cut off and
the central portion of the screen is enlarge
For 4:3 aspect ratio discs
- Normal Wide
Displays the content of the DVD title in 16:9 aspect ratio.
The picture will look horizontally stretched.
- SCREEN FIT
The top and bottom portions of the screen are cut off and
the full screen appears.
The picture will look vertically stretched.
- ZOOM FIT
The top, bottom, left and right portions of the screen are
cut off and the central portion of the screen is enlarged.
- Vertical Fit
When a 4:3 DVD is viewed on a 16:9 TV, black bars will
appear at the left and right of the screen in order to prevent
the picture from looking horizontally stretched.
If you are using a 4:3 TV
For 16:9 aspect ratio discs
- 4:3 Letter Box
Displays the content of the DVD title in 16:9 aspect ratio. The
black bars will appear at the top and bottom of the screen.
- 4:3 Pan&Scan
The left and right portions of the screen are cut off and the
central portion of the 16:9 screen is displayed.
- SCREEN FIT
The top and bottom portions of the screen are cut off and a
full screen appears. The picture will look vertically stretched.
- ZOOM FIT
The top, bottom, left and right of the screen are cut off and
the central portion of the screen is enlarged.
For 4:3 aspect ratio discs
- Normal Screen
Displays the content of the DVD title in 4:3 aspect ratio.
- SCREEN FIT
The top and bottom portions of the screen are cut off and the
full screen appears. The picture will look vertically stretched.
- ZOOM FIT
The top, bottom, left and right portions of the screen are cut
off and the central portion of the screen is enlarged.
Note
This function may behave differently depending on
the type of disc.
Selecting the Audio
Language
You can select a desired audio language quickly and
easily with the AUDIO button.
Using the AUDIO button
1. Press the Audio button. The Audio changes when the audio
button is press repeatedly.
The audio languages are represented by
abbreviations.
-
DVD
2. To remove the AUDIO icon, press the CANCEL or RETURN button.
16
Note
- This function depends on audio languages are
encoded on the disc and may not work.
- A DVD disc can contain up to 8 audio lan-
guages.
- To have the same audio language come up
whenever you play a DVD;
Refer to “Using the Audio Language” on page
20.
Selecting the Subtitle
Language
You can select a desired subtitle quickly and easily
with the SUBTITLE button.
Using the SUBTITLE button (DVD)
1. Press the SUBTITLE button. The subtitle languages are
represented by abbreviations. The subtitle changes when
the button is pressed repeatedly.
Note
- You have to change the desired subtitle in the
Disc Menu, according to discs. Press the INFO
MENU button.
- This function depends on what subtitles are
encoded on the disc and may not work on all
DVDs.
- A DVD disc can contain up to 32 subtitle
languages.
- To have the same subtitle language come up
whenever you play a DVD; Refer to “Using the
Subtitle Language” on page 20.
Changing the Camera
Angle
When a DVD contains multiple angles of a particular
scene, you can use the ANGLE function.
Using the ANGLE Function (DVD).
If the disc contains multiple angles, the ANGLE
appears on the screen.
1. During play, press the INFO button on the remote control.
2. Press the / buttons to select
3. Press the ¦/ buttons or you can use the number buttons
on the remote control to select the desired angel Angle.
DVD
English
Using the Bookmark
Function
This feature lets you bookmark sections of a DVD
so you can quickly find them at a later time.
Using the Bookmark Function
(DVD)
1. During play, press the Bookmark button on the remote
control.
Note
- Depending on a disc, the Bookmark function
may not work.
2. When you reach the scene you want to mark, press the
ENTER button. Up to12 scenes may be marked at a time.
DVD
Bookmark
Play
Clear
Bookmark
Play
Clear
1
TT:01 CH:05 Time 0:39:23
3. Press the PLAY/PAUSE ( ) button to skip to the marked
scene.
Recalling a Marked Scene
1. During play, press the bookmark button on the remocon
2. Press the /¦/ buttons to select a marked scene.
Bookmark
Play
Clear
1
2
TT:01 CH:05 Time 0:39:23
Clearing a Bookmark
1. During play, press the Bookmark button on the remocon.
2. Press the /¦/ buttons to select the bookmark num-
ber you want to delete.
3. Press the CANCEL button to delete a bookmark number.
Bookmark
Play
Clear
1
2
3
TT:01 CH:05 Time 0:39:23
17
English
Using the Zoom Function
Using the Zoom Function (DVD)
- During DVD play or pause mode, press ZOOM
button on the remocontrol repetedly to zoom in
2X/3X/4X
Clips Menu for
MP3/WMA/JPEG/CD Audio
CD Audio or discs with MP3/WMA/JPEG contain
individual songs and/or pictures that can be orga-
nized into folders as shown below. They are similar
to how you use your computer to put files into differ-
ent folders.
Open the disc tray.
Place the disc on the tray.
Close the tray.
The tray closes and this
screen displays.
-:
Current Playback Mode : There are four
modes. They can be selected in order by
pressing the REPEAT button.
- Off: Normal Playback
- Track: Repeats the current track.
- Folder: Repeats the current folder.
- Random: Files in the disc will be played in
random order.
- : STOP file icon.
- : PLAY file icon
- : WMA file icon
- : MP3 file icon.
- : JPG file icon.
- : CD file icon.
- : Folder file icon
- : current file icon
- To select the Parent Folder
Press the RETURN button to go to parent folder, or press the
/
buttons to select “..” and press ENTER to go to the
parent folder.
Folder Selection
MP3/WMA/CD Audio Playback
1. Open the disc tray. Place the disc on the tray. Close the tray.
- Only one kind of file is played back when a disc or a
folder contains both MP3 and WMA files.
2. Press the
/
buttons to select a song file.
Press ENTER to begin playback of the song file.
001/004
Off
128kbps
03:12
00:01
track 1
track 2
track 3
track 4
001/004
Off
Repeat/Random playback
Press the REPEAT button to change the playback mode. There
are four modes, such as Off, Track, Folder and Random.
- Off: Normal Playback
- Track: Repeats the current song file.
- Folder: Repeats the song files which have the same
extension in the current folder.
- Random: Song files which have the same extension will be
played in random order.
18
Picture CD Playback
1. Select the desired folder.
2. Press the
/
buttons to select a Picture file in the clips
menu and then press the ENTER button.
Rotation
- Each time the
¦/
button is pressed,the picture
rotates 90 degree clockwise.
- Each time the
button is pressed,the picture
rotate 180 degree.
- Each time the
button is pressed,the picture
go to miror appearance.
Zoom
- Each time number 7 is pressed, the picture is
enlarged.
zoom mode : 100% -125%-150%-200%-100% .
Slide show
- When you press the ENTER/PLAY at JPEG file,it
will go to full screen mode and automaically slide
show.
CD-R MP3/WMA file
When you record MP3 or WMA files on CD-R, please refer
to the following.
- Your MP3 or WMA files should be ISO 9660 or JOLIET
format.
ISO 9660 format and Joliet MP3 or WMA files are
compatible with Microsoft's DOS and Windows, and with
Apple's Mac. This format is the most widely used.
- When naming your MP3 or WMA files, do not exceed 8
characters, and enter “.mp3, .wma” as the file extension.
General name format : Title.mp3. or Title.wma. When
composing your title, make sure that you use 8 characters or
less, have no spaces in the name, and avoid the use of
special characters including: (.,/,\,=,+).
- Use a decompression transfer rate of at least 128 Kbps
when recording MP3 files.
Sound quality with MP3 files basically depends on the rate of
compression/decompression you choose. Getting CD audio
sound requires an analog/digital sampling rate, that is
conversion to MP3 format, of at least 128 Kbps and up to 160
Kbps. However, choosing higher rates, like 192 Kbps or more,
only rarely give better sound quality. Conversely, files with
decompression rates below 128 Kbps will not be played
properly.
- Use a decompression transfer rate of at least 64Kbps
when recording WMA files.
Sound quality with WMA files basically depends on the rate of
compression/decompression you choose.
Getting CD audio sound requires an analog/digital sampling
rate, that is conversion to WMA format, of at least 64Kbps
and up to 192Kbps. Conversely, files with decompression
rates below 64Kbps or over 192Kbps will not be played
properly.
- Do not try recording copyright protected MP3 files.
Certain "secured" files are encrypted and code protected to
prevent illegal copying. These files are of the following types:
Windows Media
TM
(registered trade mark of Microsoft Inc) and
SDMI
TM
(registered trade mark of The SDMI Foundation). You
cannot copy such files.
- Important:
The above recommendations cannot be taken as a
guarantee that the DVD player will play MP3 recordings, or as
an assurance of sound quality. You should note that certain
technologies and methods for MP3 file recording on CD-Rs
prevent optimal playback of these files on your DVD player
(degraded sound quality and in some cases, inability of the
player to read the files).
- This unit can play a maximum of 500 files and 500 folders
per disc.
19
English
Note
- Depending on a file size, the amount of time
between each picture may be different from the
manual.
- If you don’t press any button, the slide show will
start automatically in about 8 seconds by default.
CD-R JPEG Discs
- Only files with the “.jpg” and “.JPG” extensions can be played.
- If the disc is not closed, it will take longer to start playing and
not all of the recorded files may be played.
- Only CD-R discs with JPEG files in ISO 9660 or Joliet format
can be played.
- The name of the JPEG file may not be longer than 8
characters and should contain no blank spaces or special
characters (. / = +).
- Only a consecutively written multi-session disc can be played.
If there is a blank segment in the multi-session disc, the disc
can be played only up to the blank segment.
- A maximum of 500 images can be stored on a single CD.
- Kodak Picture CDs are recommended.
- When playing a Kodak Picture CD, only the JPEG files in the
pictures folder can be played.
- When playing a Kodak Picture CD, only the JPEG files in the
pictures folder can be played.
- Kodak Picture CD: The JPEG files in the pictures folder can
be played automatically.
- Konica Picture CD: If you want to see the Picture, select the
JPEG files in the clips menu.
- Fuji Picture CD: If you want to see the Picture, select the
JPEG files in the clips menu.
- QSS Picture CD: The unit may not play QSS Picture CD.
- If the number of files in 1 Disc is over 500, only 500 JPEG
files can be played.
- If the number of folders in 1 Disc is over 500, only JPEG
files in 500 folders can be played
CHANGING SETUP
CHANGING SETUP
MENU
MENU
Using the Setup Menu
The Setup menu lets you customize your DVD play-
er by allowing you to select various language prefer-
ences, set up a parental level, even adjust the play-
er to the type of television screen you have.
❶
Language Setup page: Setup of the Language.
❷
Audio Setup page: Setup of the Audio Options.
❸
Display Setup page: Setup of the Display Options. Use
to select which type of screen you want to watch and
several display options.
❹
Parental Setup page: Setup of the Parental Level. Allows
users to set the level necessary to prevent children from
viewing unsuitable movies such as those with violence,
adult subject matter, etc.
1. Pess the MENU button on the remote control.Use the
¦/
buttons to select Setup, then press the
or ENTER button.
2. Press the
¦/
buttons to access the different features.
Press the
or ENTER button to access the sub features.
3. To make the setup screen disappear after setting up, press
the MENU button again.
Note
Depending on the disc, some Setup Menu selec-
tions may not work.
.. Language Setup Page .. ..
Player Menu ENG
Disc Menu ENG
Audio ORI
Subtitle AUTO
20
Setting Up the Language
Features
If you set the player menu, disc menu, audio and
subtitle language in advance, they will come up
automatically every time you watch a movie.
Using the Player Menu Language
1. Press the MENU button.
2. Press the
¦/
buttons to select Language Setup, then
press the
or ENTER button.
3. Press the
/
buttons to select Player Menu, then press
the
or ENTER button.
4. Press the
/
buttons to select the desired language,
then press ENTER button.
- The language is selected and the screen
returns to Language Setup page.
- To make the setup menu disappear, press the MENU
button.
Using the Disc Menu Language
This function changes the text language only on the
disc menu screens.
1. Press the MENU button.
2. Press the
¦/
buttons to select Language Setup page,
then press the
or ENTER button.
3. Press the
/
buttons to select Disc Menu, then press
the ENTER button.
4. Press the
/
buttons to select the desired language,
then press the ENTER button.
- The language is selected and the screen returns to
Language Setup page
- To make the setup menu disappear, press the MENU
button.
.. Language Setup Page .. ..
Player Menu ENG
Disc Menu ENG
Audio ORI
Subtitle AUTO
English
Français
Deutsch
Español
Italiano
Nederlands
Cesky
Dansk
.. Language Setup Page .. ..
Player Menu ENG
Disc Menu ENG
Audio ORI
Subtitle AUTO
English
Français
Deutsch
Español
Italiano
Nederlands
Using the Audio Language
1. Press the MENU button.
2. Press the
¦/
buttons to select Language Setup page,
then press the
or ENTER button.
3. Press the
/
buttons to select Audio, then press ENTER
button.
Using the Subtitle Language
1. Press the MENU button.
2. Press the
¦/
buttons to select Language Setup, then
press the
or ENTER button.
3. Press the
/
buttons to select Subtitle, then press the
or ENTER button.
4. Press the
/
buttons to select the desired language,
then press the ENTER button.
- Select “Automatic” if you want the subtitle language to
be the same as the language selected as the audio
language.
- Some discs may not contain the language you select as
your initial language; in that case the disc will use its
original language setting.
- The language is selected and the screen returns to
setup menu.
- To make the setup menu disappear, press the MENU
button.
4. Press the
/
buttons to select the desired language, then
press ENTER button.
- Select “Original” if you want the default soundtrack
language to be the original language the disc is
recorded in.
- If the selected language is not recorded on the disc, the
original pre-recorded language is selected.
- The language is selected and the screen returns to
Language Setup menu.
- To make the setup menu disappear, press the MENU
button.
Original
English
Français
Deutsch
Español
Italiano
Nederlands
Cesky
Automatic
English
Français
Deutsch
Español
Italiano
Nederlands
Cesky
.. Language Setup Page .. ..
Player Menu ENG
Disc Menu ENG
Audio ORI
Subtitle AUTO
.. Language Setup Page .. ..
Player Menu ENG
Disc Menu ENG
Audio ORI
Subtitle AUTO
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
