Chicago Electric 91995 Operating instructions

Brand: Chicago Electric

Model: 91995

Category: Power universal cutters

Type: Operating instructions

10” COMPOUND MITER SAW

91995

SET UP AND OPERATING INSTRUCTIONS

Distributed exclusively by Harbor Freight Tools

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our website at: http://www.harborfreight.com

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

2004 by Harbor Freight Tools

contained herein may be reproduced in any shape or form without the express written consent of

Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein. Tools required for

assembly and service may not be included.

For technical questions or replacement parts, please call 1-800-444-3353.

Manual Revised 07k, 09d

SKU 91995 For technical questions, please call 1-800-444-3353. Page 2

SAVE THIS MANUAL

Keep this manual for the safety warn-

ings and precautions, assembly, operat-

ing, inspection, maintenance and cleaning

procedures. Write the product’s serial

number in the back of the manual near the

assembly diagram (or month and year of

purchase if product has no number). Keep

this manual and the receipt in a safe and

dry place for future reference.

IMPORTANT SAFETY

INFORMATION

In this manual, on the labeling,

and all other information provid-

ed with this product:

This is the safety alert

symbol. It is used to alert

you to potential personal

injury hazards. Obey all

safety messages that

follow this symbol to avoid

possible injury or death.

DANGER indicates

a hazardous

situation which, if not

avoided, will result in death or

serious injury.

WARNING

indicates a

hazardous situation which, if

not avoided, could result in

death or serious injury.

CAUTION, used

with the safety

alert symbol, indicates a

hazardous situation which, if

not avoided, could result in

minor or moderate injury.

NOTICE is used to

address practices

not related to personal injury.

CAUTION, without

the safety alert

symbol, is used to address

practices not related to

personal injury.

General Tool Safety Warnings

WARNING Read all safety

warnings and instructions.

Failure to follow the warnings and

instructions may result in electric

shock, re and/or serious injury.

Save all warnings and

instructions for future reference.

KEEP GUARDS IN PLACE and in 1.

working order.

REMOVE ADJUSTING KEYS AND 2.

WRENCHES. Form habit of check-

ing to see that keys and adjusting

wrenches are removed from tool

before turning it on.

KEEP WORK AREA CLEAN. Clut-3.

tered areas and benches invite ac-

cidents.

DON’T USE IN DANGEROUS EN-4.

VIRONMENT. Don’t use power tools

in damp or wet locations, or expose

them to rain. Keep work area well

lighted.

KEEP CHILDREN AWAY. All visitors 5.

should be kept safe distance from

work area.

MAKE WORKSHOP KID PROOF 6.

with padlocks, master switches, or by

removing starter keys.

REV 09d

SKU 91995 For technical questions, please call 1-800-444-3353. Page 3

DON’T FORCE TOOL. It will do the 7.

job better and safer at the rate for

which it was designed.

USE RIGHT TOOL. Don’t force tool 8.

or attachment to do a job for which it

was not designed.

RECOMMENDED MINIMUM WIRE

GAUGE FOR EXTENSION CORDS

(120 VOLT)

NAMEPLATE

AMPERES

(at full load)

EXTENSION CORD

LENGTH

25’ 50’ 100’ 150’

0 – 6 18 16 16 14

6.1 – 10 18 16 14 12

10.1 – 12 16 16 14 12

12.1 – 16 14 12 Do not use.

TABLE A

USE PROPER EXTENSION CORD. 9.

Make sure your extension cord is

in good condition. When using an

extension cord, be sure to use one

heavy enough to carry the current

your product will draw. An undersized

cord will cause a drop in line voltage

resulting in loss of power and over-

heating. Table A shows the correct

size to use depending on cord length

and nameplate ampere rating. If in

doubt, use the next heavier gauge.

The smaller the gauge number, the

heavier the cord.

WEAR PROPER APPAREL. Do not 10.

wear loose clothing, gloves, neck-

ties, rings, bracelets, or other jewelry

which may get caught in moving

parts. Nonslip footwear is recom-

mended. Wear protective hair cover-

ing to contain long hair.

ALWAYS USE SAFETY GLASSES. 11.

Also use face or dust mask if cutting

operation is dusty. Everyday eye-

glasses only have impact resistant

lenses, they are NOT safety glasses.

SECURE WORK. Use clamps or a 12.

vise to hold work when practical. It’s

safer than using your hand and it

frees both hands to operate tool.

DON’T OVERREACH. Keep proper 13.

footing and balance at all times.

MAINTAIN TOOLS WITH CARE. 14.

Keep tools sharp and clean for best

and safest performance. Follow

instructions for lubricating and chang-

ing accessories.

DISCONNECT TOOLS before ser-15.

vicing; when changing accessories,

such as blades, bits, cutters, and the

like.

REDUCE THE RISK OF UNINTEN-16.

TIONAL STARTING. Make sure Trig-

ger is in off position before plugging

in.

USE RECOMMENDED ACCESSO-17.

RIES. Consult the owner’s manual for

recommended accessories. The use

of improper accessories may cause

risk of injury to persons.

NEVER STAND ON TOOL. Serious 18.

injury could occur if the tool is tipped

or if the cutting tool is unintentionally

contacted.

CHECK DAMAGED PARTS. Before 19.

further use of the tool, a guard or

other part that is damaged should

be carefully checked to determine

that it will operate properly and per-

form its intended function – check for

alignment of moving parts, binding

of moving parts, breakage of parts,

mounting, and any other conditions

that may affect its operation. A guard

REV 09d

SKU 91995 For technical questions, please call 1-800-444-3353. Page 4

or other part that is damaged should

be properly repaired or replaced.

DIRECTION OF FEED. Feed work 20.

into a blade or cutter against the

direction of rotation of the blade or

cutter only.

NEVER LEAVE TOOL RUNNING 21.

UNATTENDED. TURN POWER OFF.

Don’t leave tool until it comes to a

complete stop.

GROUNDING INSTRUCTIONS

TO PREVENT

ELECTRIC SHOCK

AND DEATH FROM

INCORRECT GROUNDING

WIRE CONNECTION

READ AND FOLLOW THESE

INSTRUCTIONS:

110-120 V~ Grounded Tools: Tools

with Three Prong Plugs

In the event of a malfunction or 1.

breakdown, grounding provides a

path of least resistance for electric

current to reduce the risk of electric

shock. This tool is equipped with an

electric cord having an equipment-

grounding conductor and a ground-

ing plug. The plug must be plugged

into a matching outlet that is properly

installed and grounded in accordance

with all local codes and ordinances.

Do not modify the plug provided – if it 2.

will not t the outlet, have the proper

outlet installed by a qualied electri-

cian.

Improper connection of the equip-3.

ment-grounding conductor can re-

sult in a risk of electric shock. The

conductor with insulation having an

outer surface that is green with or

without yellow stripes is the equip-

ment-grounding conductor. If repair

or replacement of the electric cord or

plug is necessary, do not connect the

equipment-grounding conductor to a

live terminal.

Check with a qualied electrician or 4.

service personnel if the grounding

instructions are not completely under-

stood, or if in doubt as to whether the

tool is properly grounded.

Use only 3-wire extension cords that 5.

have 3-prong grounding plugs and

3-pole receptacles that accept the

tool’s plug.

Repair or replace damaged or worn 6.

cord immediately.

125 V~ 3-Prong Plug and Outlet

(for up to 125 V~ and up to 15 A)

Grounding

This tool is intended for use on a cir-7.

cuit that has an outlet that looks like

the one illustrated above in 125 V~

3-Prong Plug and Outlet. The tool

has a grounding plug that looks like

the plug illustrated above in 125 V~

3-Prong Plug and Outlet.

The outlet must be properly installed 8.

and grounded in accordance with all

codes and ordinances.

REV 09d

SKU 91995 For technical questions, please call 1-800-444-3353. Page 5

Do not use an adapter to connect this 9.

tool to a different outlet.

Miter Saw Safety Warnings

For Your Own Safety Read Instruction

Manual Before Operating Miter Saw

Wear eye protection.1.

Keep hands out of path of saw blade.2.

Do not operate saw without guards in 3.

place.

Do not perform any operation free-4.

hand.

Never reach around saw blade.5.

Turn off tool and wait for saw blade 6.

to stop before moving workpiece or

changing settings.

Disconnect power before changing 7.

blade or servicing.

To reduce risk of injury, return car-8.

riage to the full rear position after

each crosscut operation.

Release lower guard retraction 9.

mechanism after each cut and before

moving or removing the work piece.

Blade adjustment is to be made with

the power off and the blade stopped.

Return all guards to original position if 10.

any are moved during blade replace-

ment. Check all guards for proper

operation after service.

The lock down pin is to be used only 11.

to lock the head in place for carrying

and storage. It is not to be used for

any cutting operation.

DO NOT OPERATE WITH ANY 12.

GUARD DISABLED, DAMAGED,

OR REMOVED. Moving guards

must move freely and close in-

stantly.

Replacing the Saw Blade only with 13.

a new blade with a diameter of 10”,

an RPM rating of at least 5,300,

and a 5/8” arbor hole.

To avoid accidental injury, always 14.

wear heavy duty work gloves when

changing Saw Blade.

Before use, make sure the Saw 15.

Blade is properly mounted on the

Saw Spindle. Make sure the Saw

Blade is balanced, and is not cracked

or bent.

The Saw Blade will become hot 16.

while cutting. Allow the Saw Blade

to completely cool before touching.

Make sure the workpiece is free 17.

from nails and any other foreign

objects which can damage the Saw

Blade.

The Cross Pin (28) should always 18.

be in the “locked down” position

when the Saw is not being used

and when the Saw is being trans-

ported. The Cross Pin should be

activated in the “locked up” posi-

tion when changing Saw Blades.

NEVER use the Cross Pin in any

cutting operation. The Cross Pin

allows the operator to lock the Saw

Blade in position, preventing the Saw

Blade from being raised or lowered.

Allow the Saw Blade to spin up to 19.

full speed before feeding it into the

workpiece. Do not force the Saw

Blade into the workpiece when cut-

ting. Apply moderate pressure, allow-

ing the Saw Blade to cut without be-

ing forced. When turning off the Saw,

allow the Saw Blade to spin down

REV 09d

SKU 91995 For technical questions, please call 1-800-444-3353. Page 6

and stop on its own. Do not press

against the Saw Blade to stop it.

Industrial applications must follow 20.

OSHA requirements.

Proper Miter Saw location: 21. Make

sure the Miter Saw is located on a

at, level, sturdy surface capable of

supporting the weight of the Miter

Saw, workpieces, and all other tools

and accessories.

Never attempt to remove material 22.

stuck in the moving parts of the

Miter Saw while the machine is

plugged in and running.

The use of accessories or attach-23.

ments not recommended by the

manufacturer may result in a risk of

injury to persons.

When servicing use only identical 24.

replacement parts.

Only use safety equipment that has 25.

been approved by an appropriate

standards agency. Unapproved

safety equipment may not provide

adequate protection. Eye protection

must be ANSI-approved and breath-

ing protection must be NIOSH-ap-

proved for the specic hazards in the

work area.

Industrial applications must follow 26.

OSHA guidelines.

Maintain labels and nameplates on 27.

the tool. These carry important safety

information. If unreadable or miss-

ing, contact Harbor Freight Tools for a

replacement.

Avoid unintentional starting. Prepare 28.

to begin work before turning on the

tool.

People with pacemakers should 29.

consult their physician(s) before use.

Electromagnetic elds in close prox-

imity to heart pacemaker could cause

pacemaker interference or pacemak-

er failure.

WARNING: Some dust created by 30.

power sanding, sawing, grinding, drill-

ing, and other construction activities,

contains chemicals known [to the

State of California] to cause cancer,

birth defects or other reproductive

harm. Some examples of these

chemicals are:

• Lead from lead-based paints

• Crystalline silica from bricks and ce-

ment or other masonry products

• Arsenic and chromium from chemi-

cally treated lumber

Your risk from these exposures var-

ies, depending on how often you do

this type of work. To reduce your

exposure to these chemicals: work in

a well ventilated area, and work with

approved safety equipment, such as

those dust masks that are specially

designed to lter out microscopic

particles. (California Health & Safety

Code § 25249.5, et seq.)

WARNING: Handling the cord on 31.

this product will expose you to lead,

a chemical known to the State of

California to cause cancer, and birth

defects or other reproductive harm.

Wash hands after handling. (Califor-

nia Health & Safety Code § 25249.5,

et seq.)

The warnings, precautions, and in-32.

structions discussed in this instruction

manual cannot cover all possible con-

ditions and situations that may occur.

It must be understood by the operator

that common sense and caution are

REV 09d

SKU 91995 For technical questions, please call 1-800-444-3353. Page 7

factors which cannot be built into this

product, but must be supplied by the

operator.

Vibration Safety

This tool vibrates during use. Re-

peated or long-term exposure to

vibration may cause temporary or

permanent physical injury, particularly

to the hands, arms and shoulders. To

reduce the risk of vibration-related

injury:

Anyone using vibrating tools regu-1.

larly or for an extended period should

rst be examined by a doctor and

then have regular medical check-

ups to ensure medical problems are

not being caused or worsened from

use. Pregnant women or people

who have impaired blood circulation

to the hand, past hand injuries, ner-

vous system disorders, diabetes, or

Raynaud’s Disease should not use

this tool. If you feel any medical or

physical symptoms related to vibra-

tion (such as tingling, numbness, and

white or blue ngers), seek medical

advice as soon as possible.

Do not smoke during use. Nico-2.

tine reduces the blood supply to the

hands and ngers, increasing the risk

of vibration-related injury.

Wear suitable gloves to reduce the 3.

vibration effects on the user.

Use tools with the lowest vibration 4.

when there is a choice between dif-

ferent processes.

Include vibration-free periods each 5.

day of work.

Grip tool as lightly as possible (while 6.

still keeping safe control of it). Let

the tool do the work.

To reduce vibration, maintain the tool 7.

as explained in this manual. If any

abnormal vibration occurs, stop use

immediately.

SAVE THESE

INSTRUCTIONS.

REV 09d

SKU 91995 For technical questions, please call 1-800-444-3353. Page 8

SPECIFICATIONS

Electrical

Requirements

120 V~ / 60 Hz / 15 A (Start)

Speed 5300 RPM (No Load)

Saw Blade (Included) 10” Diameter / 60 Teeth

Arbor Size 5/8” Diameter

Crosscut Capacity

4-11/16” x 2-15/16” @ 90°

4-11/16” x 1-9/16” @ 45°

Blade Tilt Capacity 0° - 45° Left

Positive Stops 0°, 15°, 22.5°, 30°, 45°

Overall Table Size 18-1/8” W x 5-3/8” L x 3-1/8” H

E105017

UNPACKING

When unpacking, check to make sure

all the parts shown on the Parts List near

then end of this manual are included. If

any parts are missing or broken, please

call Harbor Freight Tools at

1-800-444-3353 as soon as possible.

ASSEMBLY INSTRUCTIONS

Note: For additional references to the

parts listed in the following pages,

refer to the Assembly Diagram near

the end of this manual.

To Install A Saw Blade

WARNING! Prior to performing any

assembly and/or adjustment pro-

cedures, make sure the Power

Cord (102) of the Miter Saw is un-

plugged from its electrical outlet.

Make sure the unit has completely

cooled, and wear heavy-duty work

gloves.

When replacing the Saw Blade (56), 1.

make sure the new Saw Blade has a

diameter of 10”, an RPM rating of

at least 5,300, and an arbor hole of

5/8” diameter.

FIGURE D

COVER

CASE (89)

ARROW

SAW

BLADE (56)

ARROW

SAW

TEETH

POINTING

DOWN

2. When installing a Saw Blade (56),

make sure the teeth of the Saw Blade

point downward, and that the direc-

tion of the arrow shown on the Saw

Blade matches the direction of the

arrow shown on the Cover Case (89).

(See Figure D.)

REV 07k, 09d

SKU 91995 For technical questions, please call 1-800-444-3353. Page 9

Lock the Saw Blade (56) in its 3. up-

ward position. To do so, pull out on

the Cross Pin (28). Raise and hold

the Cover Case (89) of the Miter Saw

fully upward. Turn the Cross Pin 90

degrees. Then, insert the Cross Pin

into the deep slot in its locked posi-

tion. (See Figure E.)

FIGURE E

CROSS

PIN (28)

4. CAUTION! The Cross Pin (28)

should always be activated in the

“locked down” position when the

Saw is not being used and when

the Saw is being transported. The

Cross Pin should be activated in

the “locked up” position only when

changing Saw Blades. NEVER use

the Cross Pin in any cutting opera-

tion. The Cross Pin allows the oper-

ator to lock the Saw Blade in position,

preventing the Saw Blade from being

raised or lowered. (See Figure E.)

FIGURE G

LARGE

COVER

(47)

SCREW (48)

BOLT

(50)

SAFETY

COVER

(53)

WRENCH

(110)

5. Loosen the Screw (48) that holds the

Large Cover (47) in place. Then, use

the Wrench (110) to remove the Bolt

(50). (See Figure G.)

Rotate the Large Cover (47) and 6.

Safety Cover (53) up and out of the

way. (See Figure G.)

FIGURE H

SPINDLE

LOCK (84)

7. Depress the Spindle Lock (84) to

keep the Saw Blade (56) from turn-

ing. (See Figure H.)

Rev 07k

SKU 91995 For technical questions, please call 1-800-444-3353. Page 10

SPINDLE

BOLT (58)

CLOCKWISE

TO LOOSEN

COUNTERCLOCKWISE

TO TIGHTEN

OUTER

FLANGE (57)

FIGURE I

8. Use the Wrench (110) to unscrew and

remove the Spindle Bolt (58) clock-

wise.

NOTE: The Spindle Bolt unscrews in a

clockwise direction. Then, remove

the Outer Flange (57).

(See Figure I.)

Release pressure on the Spindle 9.

Lock (84). (See Figure H.)

Wearing heavy duty work gloves to 10.

avoid accidental cuts, remove the old

Saw Blade (56).

Install the new Saw Blade (56), mak-11.

ing sure the teeth of the Saw Blade

are pointing downward.

(See Figure D.)

Reassemble the Outer Flange (57), 12.

and Spindle Bolt (58) rmly.

(See Figure I.)

Swing the Large Cover (47) and 13.

Safety Cover (53) back in place, mak-

ing sure the Safety Cover covers the

Saw Blade (56). (See Figure G.)

Reinstall the Bolt (50), and retighten 14.

the Screw (48). (See Figure G.)

Make sure the Safety Cover (53) 15.

returns to its original position prior to

operating the Miter Saw.

CAUTION! Make sure to pull out on

the Cross Pin (28). Turn the Cross

Pin 90 degrees. Then, insert the

Cross Pin into the shallow slot in

its unlocked position. NEVER use

the Cross Pin in any cutting opera-

tion. (See Figure E.)

To Assemble Additional

Accessories

FIGURE K

CLAMP

ASSEMBLY (36)

THUMB SCREW (35)

HOLDER (9)

THUMB SCREW (10)

BASE

(8a)

GUIDE FENCE (37a)

1. A workpiece Clamp Assembly (36)

can be installed by inserting the As-

sembly into the hole located in the

Guide Fence (37a). Once inserted,

lock the Assembly in place with the

Thumb Screw (35). To clamp the

workpiece to the Base (8a) of the

Miter Saw, turn the Adjusting Knob on

the Clamp Assembly clockwise.

(See Figure K.)

A workpiece Holder (9) can be insert-2.

ed into each side of the Base (8a),

adjusted for the desired length, and

locked in place with the Thumb Screw

(10). The Holders should be used as

supports when cutting longer length

workpieces. (See Figure K.)

SKU 91995 For technical questions, please call 1-800-444-3353. Page 11

The Safety Cover

The transparent Safety Cover (53) 1.

automatically rotates to cover the

Saw Blade (56) when the Cover Case

(89) is lifted. When the Cover Case

is lowered, the Safety Cover rotates

back out of the way.

Do not disconnect or remove the 2.

Safety Cover (53). Do not operate

the Miter Saw if the Safety Cover is

damaged or missing.

If the transparent Safety Cover (53) 3.

becomes so dirty that the Saw Blade

(56) cannot be seen clearly, discon-

nect the electrical Power Cord from

its electrical outlet and clean the

Safety Cover with a soft, damp, cloth.

A mild detergent may be used, but do

not use solvents which may damage

the Safety Cover.

The Trigger

Before plugging in the Miter Saw,

check the operation of the Trigger (98).

Do not operate the Miter Saw if the Trigger

is not operating properly. To turn on the

Miter Saw, simply squeeze the Trigger. To

turn off the tool, release pressure on the

Trigger.

The Dust Bag

DUST

BAG

(93)

DUST TUBE (94)

FIGURE N

1. The Dust Bag (93) catches and holds

the wood chips and saw dust when

the Miter Saw is in operation.

(See Figure N.)

The 2. outside diameter of the Dust

Tube (94) is 1-3/4” to which the Dust

Bag (93) or a vacuum hose (not in-

cluded) may be attached. It is recom-

mended that only a qualied techni-

cian perform this procedure.

(See Figure N.)

SKU 91995 For technical questions, please call 1-800-444-3353. Page 12

To Adjust The Cutting Depth

WARNING! Prior to performing this

procedure, make sure the Power

Cord (102) of the Miter Saw is un-

plugged from its electrical outlet.

The depth of cut may be adjusted to 1.

a maximum of 4-11/16” at 90°, and

4-11/16” at 45°.

FIGURE O

TABLE

(18a)

KERF

BOARD

(11a)

SCREW

(92)

BASE (8a)

GAUGE

HANDLE

(1a)

2. Slightly loosen the Screw (92) and

pull the Miter Saw’s Cover Case

(89) downward as far as it will go.

Observe whether the edge of the

Saw Blade (56) passes completely

through the Kerf Board (11a).

(See Figure O.)

If the Saw Blade (56) does not pass 3.

completely through the Kerf Board

(11a), lower the Saw Blade further by

loosening the Screw (92).

(See Figure O.)

After adjusting the Screw (92), press 4.

down on the Miter Saw and make

sure the Saw Blade (56) does not

contact the bottom of the Table (18a)

or any other part of the Saw Base

(8a). (See Figure O.)

If the Saw Blade (56) touches the 5.

Table (18a) or any other part of the

Saw Base (8a), tighten the Screw

(92) to raise the Saw Blade slightly

until it clears. (See Figure O.)

To Adjust The Miter Angle

WARNING! Prior to performing this

procedure, make sure the Power

Cord (102) of the Miter Saw is un-

plugged from its electrical outlet.

The miter angle of a cut may be ad-1.

justed 0 - 45° to the right or left. To

do so, loosen the Handle (1a) located

at the front of the Table (18a).

(See Figure O.)

Move the Handle (1a) to the right or 2.

left until the desired miter angle of

cut is indicated by the Gauge located

on the Base (8a). Then, tighten the

Handle (1a) to lock the Miter Angle in

place. (See Figure O.)

SKU 91995 For technical questions, please call 1-800-444-3353. Page 13

To Adjust The Bevel Of Cut

WARNING! Prior to performing this

procedure, make sure the Power

Cord (102) of the Miter Saw is un-

plugged from its electrical outlet.

FIGURE P

HANDLE

(30)

GAUGE

(24)

BACK RACK

(25)

1. The bevel angle (or Saw Blade tilt

capacity) may be adjusted from 0 -

45° to the left. To do so, loosen the

Handle (30) located at the rear of the

Miter Saw. (See Figure P.)

Tilt the Back Rack (25) until the de-2.

sired bevel angle of cut is achieved

as indicated on the Gauge (24).

Then, re-tighten the Handle (30) to

lock the Back Rack in place.

(See Figure P.)

SKU 91995 For technical questions, please call 1-800-444-3353. Page 14

BASIC OPERATION

WARNING! Make sure the Power

Cord (102) of the Miter Saw is un-

plugged from its electrical outlet.

Then, if necessary, make adjustments

to the workpiece Holder (9), cutting

depth, miter angle, and bevel angle.

Raise the Saw Blade (56) up to allow 1.

positioning of the workpiece.

Check to make sure the Trigger (98) 2.

is operating properly.

Place the workpiece on the Table 3.

(18a) and against the Guide Fence

(37a).

Use the Clamp Assembly (36) to hold 4.

the workpiece in place.

Plug the Power Cord (102) into the 5.

nearest 120 volt, grounded, electri-

cal outlet.

Squeeze the Trigger (98) to turn on 6.

the Miter Saw.

When the Saw Blade (56) is turning 7.

at full speed, slowly bring down the

Motor Housing (75) to complete the

cut.

Note: Feed the Saw Blade into the work-

piece gradually. Do not force the

machine to remove material faster

than it was designed to cut.

When cutting a large workpiece, 8.

make sure its entire length is properly

supported. If necessary, use a roller

stand (not included) with a larger

workpiece.

Never attempt to remove material 9.

stuck in the moving parts of the Miter

Saw while it is plugged in and run-

ning.

Turn off the Miter Saw if the work-10.

piece is to be backed out of an un-

completed cut.

When the cut is complete, release the 11.

Trigger (98) to turn off the Miter Saw.

Wait until the Saw Blade (56) comes 12.

to a complete stop. Raise the Mo-

tor Housing (75). Then, unplug the

Power Cord (102) from its electri-

cal outlet.

Loosen the Clamp Assembly (36), 13.

and remove the workpiece and scrap

material from the Table (18a).

SKU 91995 For technical questions, please call 1-800-444-3353. Page 15

INSPECTION, MAINTENANCE,

AND CLEANING

WARNING! Always make sure the

Trigger (98) is in its “OFF” posi-

tion, and unplug the Power Cord

(102) from its 120 volt electrical

outlet before performing any in-

spection, adjustments, mainte-

nance, or cleaning.

Make sure the power tool is cool to

the touch before inspection, mainte-

nance, and cleaning begin. Always

protect your hands by wearing work

gloves.

Before each use,1. inspect the general

condition of the Miter Saw. Check

for loose screws, misalignment or

binding of moving parts, cracked or

broken parts, damaged electrical

wiring, loose, cracked, or bent Saw

Blade (56), and any other condition

that may affect its safe operation. If

abnormal noise or vibration occurs,

have the problem corrected before

further use.

Do not use damaged equipment.

Never work with a dull saw blade.

Daily: 2. With a soft brush, cloth, or

vacuum, remove all dust and debris

from the Miter Saw. Then, use a

premium quality, lightweight machine

oil to lubricate all moving parts except

the Saw Blade (56).

FIGURE Q

BRUSH

COVER (72)

BRUSH COVER (72)

(NOT SHOWN)

3. To replace the Motor Carbon

Brushes: It may become neces-

sary at sometime to replace the two

Carbon Brushes (73) when the Mo-

tor performance decreases, or stops

working completely. The Carbon

Brushes are located on each side

of the Motor Housing (75), see Fig-

ure Q. To replace the brushes:

Remove the two Brush Covers a.

(72). Then, remove the two Carbon

Brushes from the Brush Holders

(74).

If the Carbon Brushes are worn b.

down more than 1/2, replace both

Carbon Brushes. If, however, the

Carbon Brushes are just dirty they

may be cleaned by rubbing them

with a pencil eraser.

When installing the Carbon Brushes, c.

make sure the carbon portion of the

Carbon Brushes contact the Motor

Armature, and that the springs face

away from the Motor. Also, make

sure the springs operate freely.

Replace the Brush Holders.d.

NOTE: New Carbon Brushes tend to

arc or spark when rst used until

they wear and conform to the Mo-

tor’s Armature.

SKU 91995 For technical questions, please call 1-800-444-3353. Page 16

WARNING! All other maintenance

and servicing should be performed

only by a qualied service techni-

cian.

PLEASE READ THE

FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR

HAS PROVIDED THE PARTS LIST AND ASSEMBLY

DIAGRAM IN THIS MANUAL AS A REFERENCE

TOOL ONLY. NEITHER THE MANUFACTURER OR

DISTRIBUTOR MAKES ANY REPRESENTATION

OR WARRANTY OF ANY KIND TO THE BUYER

THAT HE OR SHE IS QUALIFIED TO MAKE ANY

REPAIRS TO THE PRODUCT, OR THAT HE OR

SHE IS QUALIFIED TO REPLACE ANY PARTS OF

THE PRODUCT. IN FACT, THE MANUFACTURER

AND/OR DISTRIBUTOR EXPRESSLY STATES

THAT ALL REPAIRS AND PARTS REPLACEMENTS

SHOULD BE UNDERTAKEN BY CERTIFIED AND

LICENSED TECHNICIANS, AND NOT BY THE

BUYER. THE BUYER ASSUMES ALL RISK AND

LIABILITY ARISING OUT OF HIS OR HER REPAIRS

TO THE ORIGINAL PRODUCT OR REPLACEMENT

PARTS THERETO, OR ARISING OUT OF HIS OR

HER INSTALLATION OF REPLACEMENT PARTS

THERETO.

SKU 91995 For technical questions, please call 1-800-444-3353. Page 17

PARTS LIST

Note: Some parts are listed and shown for illustration purposes only, and are not avail-

able individually as replacement parts.

Part Description

1a Handle

7 Screw

8a Base

9 Holder

10 Thumb Screw

11a Kerf Board

12 Screw

14 Nut

15 Pointer

16 Spring

17 Screw

18a Table

19 Nut

20 Screw

21 Gasket

22 Spring Gasket

23 Screw

24 Gauge

25 Back Rack

26 Nut

28 Cross Pin

29 Screw

30 Handle

31 Screw

32 Spring

33 Spring Base

34 Small Base

35 Thumb Screw

36 Clamp Assembly

37a Guide Fence

38 Connecting Bar

39 Screw

40 Gasket

41 Gasket

42 Gasket

43 Gasket

44 Screw

45 Nut

46 Small Cover

47 Large Cover

Part Description

48 Screw

49 Spring

50 Bolt

51 Gasket

52 Screw

53 Safety Cover

54 Spring Gasket

55 Screw

56 Saw Blade

57 Outer Flange

58 Spindle Bolt

59 Inner Flange

60 Pin

61 Arbor

62 Bearing

63 Bearing Box

64 Gear

65 Blind Ring

66 Needle Bearing

67 Spring

68 Spring Cover

69 Screw

70 Screw

71 Spring Gasket

72 Carbon Brush Cover

73 Carbon Brush

74 Carbon Brush Holder

75 Motor Housing

76 Screw

77 Spring Gasket

78 Gasket

79 Stator

80 Windshield Ring

81 Bearing

82 Armature

83 Bearing

84 Spindle Lock

85 Middle Cover

86 Screw

87 Fixed Rod

Part Description

88 Screw

89 Cover Case

90 Screw

91 Rubber Gasket

92 Screw

93 Dust Bag

94 Dust Tube

95 Hanging Ring

96 Screw

97 Switch Gasket

98 Trigger

99 Rubber Buff

100 Handle (Lower)

101 Sheathing

102 Power Cord

103 Wire Holding Board

104 Screw

105 Handle (Upper)

106 Screw

107 Nut

108 Screw

109 Plate

110 Wrench (Not Shown)

111 Screw

112 Bracket

113 Angle Spring

114 Spring Washer

115 Screw

116 Rubber Stopper

117 Screw

118 Pointer

119 Screw

120 Spring

121 Steel Ball

122 Washer

123 Spring

124 Roll Pin

125 Lock Nut

REV 08h, 09d

SKU 91995 For technical questions, please call 1-800-444-3353. Page 18

ASSEMBLY DIAGRAM

110: WRENCH NOT SHOWN.

Note: Some parts are listed and shown for illustration purposes only, and are not avail-

able individually as replacement parts.

REV 08h, 09d

113

SKU 91995 For technical questions, please call 1-800-444-3353. Page 19

LIMITED 90 DAY WARRANTY

Harbor Freight Tools Co. makes every effort to assure that its products meet high

quality and durability standards, and warrants to the original purchaser that this prod-

uct is free from defects in materials and workmanship for the period of 90 days from

the date of purchase. This warranty does not apply to damage due directly or indirectly,

to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities,

criminal activity, improper installation, normal wear and tear, or to lack of maintenance.

We shall in no event be liable for death, injuries to persons or property, or for incidental,

contingent, special or consequential damages arising from the use of our product. Some

states do not allow the exclusion or limitation of incidental or consequential damages, so

the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESS-

LY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE

WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with

transportation charges prepaid. Proof of purchase date and an explanation of the com-

plaint must accompany the merchandise. If our inspection veries the defect, we will ei-

ther repair or replace the product at our election or we may elect to refund the purchase

price if we cannot readily and quickly provide you with a replacement. We will return re-

paired products at our expense, but if we determine there is no defect, or that the defect

resulted from causes not within the scope of our warranty, then you must bear the cost

of returning the product.

This warranty gives you specic legal rights and you may also have other rights

which vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353

REV 09d

Chicago Electric 91995 Operating instructions

Brand: Chicago Electric

Model: 91995

Category: Power universal cutters

Type: Operating instructions

Download PDF

report

Chicago Electric 91995 Operating instructions

Chicago Electric 91995 Operating instructions

Related papers

Other documents