Tunturi E 2 User manual

:: 1

E2

Owner's Manual :: 2-12

GB

Mode d'emploi :: 13-23

F

Manual del usario :: 24-34

E

Gebruikers gids :: 35-45

NL

583 1028A

2 :: :: 3

WELCOME TO THE WORLD OF

TUNTURI EXERCISING!

Your choice shows that you really want to invest in your well-being and

condition; it also shows you really value high quality and style. In Tunturi

Fitness Equipment, you’ve chosen a high-quality, safe and motivational

training partner. Whatever your training goal, we are certain this is the

equipment to get you there.

ASSEMBLY ::

Start by unpacking the equipment and check that you have the following

parts:

1. Frame

2. Rear support

3. Plastic covers for front support (2)

4. Handlebar / interface

5. Ear sensor

6. Assembly hardware kit (contents are marked with an * in the spare

part list)

In case of problems contact your Tunturi dealer.

The packaging includes a silicate bag for absorbing moisture during

storage and transportation. Please dispose of the bag once you have

unpacked the equipment.

The directions left, right, front and back are deﬁ ned as seen from the

exercising position. The ﬁ gures referred to in the text are in the back

fold.

Assemble your ﬁ tness equipment as follows:

IMPORTANT SAFETY INSTRUCTIONS

This manual is an essential part of your equipment: read it

through carefully before assembling, using or servicing your

equipment. Please keep the manual somewhere safe; it will

provide you now and in the future with the information you

need to use and maintain your equipment. Always follow these

instructions with care.

:: Before you start any training, consult a physician to check your

state of health.

:: If you experience nausea, dizziness or other abnormal symptoms

while exercising, stop your workout at once and consult a

physician.

:: The device is not to be used outdoors. E2 tolerates an

environment measuring + 10º C to + 35ºC. Air humidity must

never exceed 90 %.

:: Place the equipment on a ﬁ rm, level and protected surface.

:: The device can only be used at home.

:: Make sure the equipment is unplugged before carrying out any

assembly or maintenance procedures.

:: Before you start using the equipment, make sure it functions

correctly in every way. Do not use faulty equipment.

:: Do not attempt any servicing or adjustments other than those

described in this manual. All other servicing else must be left to

someone familiar with the maintenance of electro-mechanical

devices and authorised under the laws of the country in question

to carry out maintenance and repair work. Always follow these

maintenance instructions.

:: The electromagnetic brake forms a magnetic ﬁ eld that may

damage the mechanism of a watch, or the magnetic identiﬁ cation

strip on a credit or cash card, should they come into immediate

contact with the magnetic ﬁ eld.

:: Press the keys with the tip of the ﬁ nger; your nails may damage

the key membrane.

:: The device must not be used by persons weighing over 135 kg.

4 :: :: 5

ADJUSTMENTS ::

CORRECT EXERCISING POSITION

The seat height should be set so that the heal of the foot reaches the pedal

with the leg straight and the pedal at its lowest point. To raise or lower

the seat: First turn the locking knob one turn counter-clockwise, then

pull the locking knob outwards, so that the seat tube can be moved

freely up and down. Once the height is right, let go of the knob and

the seat locks into

place. Turn the locking knob clockwise to tighten. NOTE! Always make

sure that the locking knob is properly fastened before starting to exercise!

The scale on the seat tube helps you remember the seat height that suits

you best. The seat can be inclined forward or backward by turning the

green adjustment ring below the saddle. The seat inclines forward when

the ring is turned clockwise, and back when the ring is turned counter-

clockwise. Do not try to adjust seat inclination when you’re sitting on the

seat - the ring won’t turn.

HANDLEBAR SET-UP

Loosen the grey knob in front of the handlebar and adjust the handlebar

position until your training position feels comfortable. Tighten the grey

knob carefully.

PEDALS

Select strap tightness, set the appropriate strap hole on the retainer from

below and pull forcibly upward. Especially when the equipment is new,

the strap fastening may seem relatively tight.

PEDALLING RESISTANCE

To increase or decrease resistance, turn the adjustment knob at the top of

the handlebar support tube clockwise (+ direction) to increase resistance

and counterclockwise (- direction) to decrease resistance. The scale above

the knob (0-8) helps you ﬁ nd and reset a suitable resistance.

SUPPORTS (FIGURES 1 AND 2)

:: Place the rear support under the frame and fasten it with two hex

screws and washers.

:: Tilt the cycle back so that it rests on the rear support and seat.

Push the plastic covers into place at the ends of the front support.

Turn the cycle back to upright position.

HANDLEBAR (FIGURES 3 AND 4)

:: Expose the wire coming from the frame tube by unwrapping the

tape that covers it, and then connect it to the counterpart in the

handlebar support tube. Ensure that the joint is securely locked by

gently pulling the wire.

:: Thread the wire carefully inside the frame tube and push the

handlebar support tube into place inside the frame tube, so that

the fastening screws are on the front of the tube.

:: NOTE! Use the enclosed Allen key to tighten both fastening

screws through the holes in the tube. Tighten the fastening screws

by turning them counter-clockwise.

:: Pull out the tape protecting batteries from the side of the meter.

The meter becomes activated.

:: Remove the protecting ﬁ lm from the display.

6 :: :: 7

PULSE MEASUREMENT ::

1. Push the ear sensor connector into the interface connector.

2. Attach the ear sensor to your earlobe.

3. Attach the sensor wire to your shirt with the clip provided. This

prevents the sensor and wire from moving, which may interfere

with measuring.

If there are problems in pulse measurement:

:: The display shows - - instead of the heart rate.

:: Check how the sensor works while not pedalling.

:: Try measuring on the inside surface of the ear or on the tip of your

ﬁ nger.

:: Rub the earlobe with your ﬁ ngers to quicken circulation.

:: If pulse values rise above 150 beats/min., earlobe measurement

may be affected by the faster circulation.

:: Sometimes a strong light source in the immediate vicinity of the

user may cause disturbances. Turn the ear sensor the other way

around on your earlobe.

Keep the ear sensor clean. Clean the ear sensor after use with a damp

cloth and dry carefully.

You can buy a heart-rate belt for telemetric measurement from your

Tunturi dealer as an accessory. Due to its reliability we recommend the

heart-rate belt.

EXERCISING WITH TUNTURI ::

No matter what your goal, you’ll get the best results by training at the

right level of effort, and the best measure is your own heart-rate. First

ﬁ nd your maximum heart-rate, i.e. where the rate doesn’t increase with

added effort. If you don’t know your maximum heart rate, please use the

following formula as a guide:

Women: 226 - age Men: 220 - age

These are average values and the maximum varies from person to person.

The maximum heart rate diminishes on average by one point per year.

If you belong to a risk group, ask a doctor to measure your maximum

heart rate for you.

We have deﬁ ned three different heart-rate zones to help you with targeted

training.

Beginner: 50-60 % of maximum heart rate

Also suitable for weight-watchers, convalescents and those who haven’t

exercised for a long time. Three sessions a week of at least a half-hour

each is recommended.

Trainer: 60-70 % of maximum heart rate

Perfect for improving and maintaining ﬁ tness. You should train for a

minimum of 30 minutes at least three times a week. To improve your

condition still further, increase either frequency or effort, but not both

at the same time!

Active trainer: 70-80 % of maximum heart rate

Exercise at this level suits only the ﬁ ttest and presupposes a long history

of exercising.

8 :: :: 9

MAIN DISPLAY ::

When you turn the user interface on, the display shows the following

exercise parameters:

1. Efﬁ ciency (W)

:: Figure indicates exercise efﬁ ciency in Watts, which depends on

pedalling speed and resistance adjustment.

2. Energy consumption (kcal/kJ)

:: Displays cumulative energy consumption (0-999); default setting

is kcal.

3. Speed (rpm / km/h / mph)

:: Default setting is rpm (pedal revolutions / minute).

4. Pulse

:: Heart rate transmitter belt or an ear sensor is required.

:: If the user interface does not receive a heart-rate signal, - - is

displayed instead of the heart rate.

NOTE! Always disconnect the ear sensor from the user interface if using

a heart rate transmitter belt; the ear sensor will interfere with the heart

rate transmitter.

5. Time

:: Displays the exercise time elapsed between 0:00 - 59:59 minutes

and between 1:00 - 10:00 hours in 1 minute increments.

:: Time display stops if speed falls to zero.

6. Distance (km / miles)

:: Default display setting is km.

:: Displays the distance travelled during the workout in km (or

miles) to two decimal points up to 9.99 km (or miles) and with

one decimal point up to 99.9.

METER ::

RESET

Pressing Reset always resets the value on the display.

SET

Press Set key for 2 seconds to set units of measurement.

:: Default units are rpm, km and kcal.

:: To change the units press the - or + key until the desired units are

displayed.

:: To measure speed you can set either revolutions per minute,

(rpm), kilometres per hour (km/h) or miles per hour (mph).

Energy consumption measurement can be set for kilocalories

(kcal) or kilojoules (kJ).

:: In addition to rpm you can also select either kilometres (km) or

miles as distance measures. If km/h is selected as the unit to

measure speed, km will automatically be the unit for distance. The

same applies to the units mph and miles.

:: The user interface automatically returns to the main display 5

seconds after the Set key was last pressed.

:: Press the Reset key to exit the setting function without saving the

adjustment. This resets the readings on the main display.

10 :: :: 11

If the display malfunctions proceed as follows:

Loosen the 6 fastening screws in the top of the meter. Carefully lift the

top and turn it so that the wire joint is exposed. Detach the joint by

pressing the lever towards the wire and pull the wire connector out. Be

careful not to let the wire drop inside the tube. If the bottom of the

meter is damaged, remove it by unscrewing the 2 fastening screws at the

bottom. Defective parts should be sent to your Tunturi dealer. Ensure

that the meter wire is securely locked in place when replacing the top of

the interface by gently pulling on the joint.

NOTE! Despite continuous quality control, defects and malfunctions

caused by individual components may occur in the equipment. In most

cases it is unnecessary to take the whole device in for repair, as it is

usually sufﬁ cient to replace the defective part. If the equipment does not

function properly during use, contact your Tunturi dealer immediately.

Always give the model and serial number of your equipment. The

location of the serial number sticker is shown on the inside cover. Please

also state the nature of the problem, conditions of use and purchase date.

If you require spare parts for your equipment, please contact your dealer

with the model, equipment serial no. and spare part number of the

required part. There is a spare part list at the back of this manual. Use

only components and parts mentioned in the spare part list.

TECHNICAL DATA ::

Length 96 cm Height 124 cm

Width 69 cm Weight 35 kg

All Tunturi models and user interfaces meet the requirements of the

EU EMC Directives on electromagnetic compatibility (89/336/EEC)

and electrical equipment designed for use within certain voltage limits

(73/23/EEC). This product therefore carries the CE label.

All Tunturi ergometers meet CEN precision and safety standards (Class

A, EN-957, parts 1 and 5).

TRANSPORT AND STORAGE ::

Follow these instructions when carrying and moving the cycle about,

because lifting it incorrectly may strain your back or risk other accidents:

Stand behind the device. Grip the seat with one hand and the handlebar

with the other, and set your foot on the rear support. Tilt the device so

that it rests on its transport wheels. Wheel the device to move it on these

transport wheels. Lower the device while holding on to the handlebar and

remain behind the device all the time.

If the device is not used for a period of time, the transmission belt may

become temporarily distorted. This can lead to slightly uneven pedalling.

However, after a few minutes of use the effect disappears as the belt

returns to its original form.

To prevent the cycle malfunctioning, store in a dry place with as little

temperature variation as possible and protected from dust.

MAINTENANCE ::

The equipment requires very little maintenance. Check, however, from

time-to-time that all screws and nuts are tight.

:: After exercising, clean the equipment with a soft, absorbent cloth.

Sweat may cause corrosion: we recommend therefore that you

protect all metal surfaces outside the plastic covers with teﬂ on or

car wax. Do not use solvents. The magnetic brake is

based on magnetic resistance; resistance level is measured

electronically and shown as a watt-reading on the display.

:: Due to the measurement system, your Tunturi ergometer need not

be recalibrated when assembled, serviced and used according to

this owner’s manual.

If the meter display shows text “LO BAT”, change the batteries. Loosen

the 6 fastening screws in the top of the meter. Carefully lift the top, cut

the ribbon over the batteries and remove the old batteries. Place the new

batteries (3 x 1.5 V AA) in the holder and replace the top of the meter.

12 :: :: 13

:: Avant de commencer un entraînement, quel qu’il soit, consultez

votre médecin.

:: En cas de nausées, vertiges ou autres symptômes anormaux,

interrompez la séance immédiatement et consultez un médecin.

:: L’appareil ne doit pas être utilisé à l’extérieur. L’appareil supporte

des températures de + 10º C à + 35ºC. L’hygrométrie ne doit

jamais excéder 90 %.

:: Installez l’appareil sur une surface plane et ferme, et sur un tapis

protecteur.

:: L’appareil peut être utilisé seulement à la maison.

:: N’utilisez jamais un appareil défectueux ou incomplet.

:: N’essayez pas d’effectuer d’autres mesures d’entretien ou réglage

que celles décrites dans ce mode d’emploi. Toutes les autres

opérations doivent être laissées aux soins des personnes

compétentes dans l’entretien des dispositifs électromagnétiques et

autorisées, au regard des lois du pays concerné (ou équivalent), à

accomplir des travaux de maintenance et réparations. Les

instructions d’entretien de ce mode d’emploi doivent être

scrupuleusement suivies.

:: Le champ magnétique généré par les aimants de l’arc de frein peut

endommager par ex. les montres ou les cartes bancaires, si elles

entrent en contact direct avec le champ en question.

:: Appuyez sur les touches avec l’intérieur des bouts de vos doigts ;

les ongles peuvent endommager le ﬁ lm les protégeant.

:: L’appareil ne doit pas être utilisé par des personnes dont le poids

excède 135 kg.

CONSEILS ET AVERTISSEMENTS

Ce manuel est une pièce essentielle de votre appareil : lisez

attentivement ce mode d’emploi avant d’assembler, d’utiliser ou

d’effectuer l’entretien de votre appareil. Veuillez conserver ce guide,

il contient les renseignements dont vous aurez besoin, maintenant

et plus tard, pour bien utiliser et entretenir votre appareil. Suivez

toujours les instructions très rigoureusement.

TIPS ::

ABOUT YOUR HEALTH

:: To avoid muscular pain and strain, begin and end each workout

by stretching.

ABOUT THE EXERCISE ENVIRONMENT

:: Make sure the exercise environment has adequate ventilation. To

avoid catching cold, do not exercise in a draughty place.

ABOUT USING THE EQUIPMENT

:: If children are allowed to use the ﬁ tness equipment, they should

be supervised and taught to use it properly, keeping in mind the

child’s physical and mental development and their personality.

:: Only one person may use the cycle at a time.

:: Protect the user interface from excess sunlight. Do not let the

interface come into contact with water.

:: Hold the handlebar for support when getting on or off the cycle.

:: Wear appropriate clothing and shoes while exercising.

:: Keep hands clear of any moving parts.

NOTE! The instructions must be followed carefully in the assembly,

use and maintenance of your equipment. The warranty does not cover

damage due to negligence of the assembly, adjustment and maintenance

instructions described herein. Changes or modiﬁ cations not expressly

approved by Tunturi Oy Ltd will void the user’s authority to operate

the equipment!

Due to our continuous policy of product development, Tunturi reserves

the right to change speciﬁ cations without notice.

We wish you many enjoyable workouts with your new Tunturi

training partner!

Page is loading ...

Tunturi E 2 User manual

Tunturi E 2 User manual

in other languages

Related papers

Other documents