Brother CS7000X User manual

Operation Manual

Product Code: 888-N00/N02/N20/N22/N40/N42

Sewing Machine

English

888-N00/N02/N20/N22/N40/N42

D01F5E-101①

To get information about Videos, please go to http://s.brother/cvkag/.

Please visit us at http://s.brother/cpkag/ where you can get the support

information (Sewing Guide, Stitch Chart, Instruction Videos, FAQs, etc.)

for your Brother product.

Trademarks

App Store is a service mark of Apple Inc.

Android and Google Play are trademarks of Google, Inc.

Use of these trademarks are subject to Google Permissions.

Brother SupportCenter is a mobile app that provides the support

information (Instruction Videos, FAQs, etc.) for your Brother product.

Visit the Google Play™ or App Store to download.

App StoreGoogle Play™

Be sure to read this document before using the machine.

We recommend that you keep this document nearby for future reference.

Cover1-4

PANTONE 285CVC

K

CONTENTS

IMPORTANT SAFETY INSTRUCTIONS ��2

Names of Machine Parts ��4

Main parts �� 4

Needle and presser foot section �� 4

Operation buttons �� 4

Flat bed attachment �� 4

Accessories ��5

Included accessories �� 5

Optional accessories �� 5

Using Your Machine ��5

Power supply �� 6

Foot controller �� 6

Operation panel �� 6

Settings/Functions �� 6

Threading the Machine ��7

Winding/Installing the bobbin �� 7

Upper threading �� 9

Drawing up the bobbin thread �� 11

Fabric/Thread/Needle Combination ��12

Needle ��13

Checking the needle �� 13

Replacing the needle �� 13

Sewing with the twin needle �� 13

Replacing the Presser Foot ��14

Replacing the presser foot �� 14

Removing the presser foot holder �� 15

Sewing Basics��15

Selecting the stitch �� 15

Setting the stitch length and stitch width �� 15

Starting to sew �� 16

Sewing reverse/reinforcement stitches �� 16

Automatic reverse/reinforcement stitching �� 17

Thread tension �� 17

Utility Stitches ��17

Overcasting stitches �� 17

Blind hem stitching �� 18

Buttonhole sewing �� 19

Button sewing (for models equipped with

the button fitting foot “M”) �� 21

Zipper insertion�� 22

Bar tack stitching �� 23

Making Adjustment��23

Brother Support Website Information

(Downloading Manuals) ��24

Care and Maintenance ��24

Restrictions on oiling �� 24

Precautions on storing the machine �� 24

Cleaning the machine surface �� 24

Cleaning the race �� 24

Troubleshooting ��25

Frequent troubleshooting topics �� 25

Upper thread tightened up �� 25

Tangled thread on wrong side of fabric �� 25

Incorrect thread tension �� 26

Fabric is caught in the machine and cannot be

removed �� 26

If the thread becomes tangled under the bobbin

winder seat�� 28

List of symptoms�� 28

Error Messages ��30

Operation beep �� 30

Index ��31

2

IMPORTANT SAFETY

INSTRUCTIONS

Please read these safety instructions before

attempting to use the machine�

DANGER

- To reduce the risk of electrical shock

1

Always unplug the machine from the

electrical outlet immediately after

using, when cleaning, making any user

servicing adjustments mentioned in

this manual, or if you are leaving the

machine unattended�

WARNING

- To reduce the risk of burns, ﬁre, electrical shock, or

injury to persons�

2

Always unplug the machine from the electrical

outlet when making any adjustments mentioned

in the instruction manual�

• To unplug the machine, switch the machine to the

symbol “O” position to turn it off, then grasp the

plug and pull it out of the electrical outlet� Do not

pull on the cord�

• Plug the machine directly into the electrical outlet�

Do not use an extension cord�

•

Always unplug your machine if there is a power failure�

3

Electrical Hazards:

• This machine should be connected to an AC power

source within the range indicated on the rating label�

Do not connect it to a DC power source or inverter�

If you are not sure what kind of power source you

have, contact a qualiﬁed electrician�

• This machine is approved for use in the country of

purchase only�

4

Never operate this machine if it has a damaged

cord or plug, if it is not working properly, has been

dropped or damaged, or water is spilled on the

unit� Return the machine to the nearest authorized

Brother dealer for examination, repair, electrical or

mechanical adjustment�

• While the machine is stored or in use if you

notice anything unusual, such as an odor, heat,

discoloration or deformation, stop using the machine

immediately and unplug the power cord�

• When transporting the machine, be sure to carry it

by its handle� Lifting the machine by any other part

may damage the machine or result in the machine

falling, which could cause injuries�

• When lifting the machine, be careful not to make

any sudden or careless movements, which may

cause a personal injury�

5

Always keep your work area clear:

• Never operate the machine with any air openings

blocked� Keep ventilation openings of the machine

and foot controller free from the build up of lint,

dust, and loose cloth�

• Do not store objects on the foot controller�

• Never drop or insert foreign objects in any opening�

• Do not operate where aerosol (spray) products are

being used or where oxygen is being administered�

• Do not use the machine near a heat source, such as

a stove or iron; otherwise, the machine, power cord

or garment being sewn may ignite, resulting in ﬁre or

an electric shock�

• Do not place this machine on an unstable surface,

such as an unsteady or slanted table, otherwise the

machine may fall, resulting in injuries�

6

Special care is required when sewing:

• Always pay close attention to the needle� Do not use

bent or damaged needles�

• Keep ﬁngers away from all moving parts� Special

care is required around the machine needle�

• Switch the machine to the symbol “O” position

to turn it off when making any adjustments in the

needle area�

• Do not use a damaged or incorrect needle plate, as

it could cause the needle to break�

• Do not push or pull the fabric when sewing, and

follow careful instruction when free motion stitching

so that you do not deﬂect the needle and cause it to

break�

7

This machine is not a toy:

• Your close attention is necessary when the machine

is used by or near children�

• The plastic bag that this machine was supplied

in should be kept out of the reach of children or

disposed of� Never allow children to play with the

bag due to the danger of suffocation�

• Do not use outdoors�

3

8

For a longer service life:

• When using and storing this machine, avoid direct

sunlight and high humidity locations� Do not use or

store the machine near a space heater, iron, halogen

lamp, or other hot objects�

• Use only neutral soaps or detergents to clean the

case� Benzene, thinner, and scouring powders can

damage the case and machine, and should never be

used�

• Always consult the Operation Manual when

replacing or installing any assemblies, the presser

feet, needle or other parts to assure correct

installation�

9

For repair or adjustment:

• If the light unit is damaged, it must be replaced by

an authorized Brother dealer�

• In the event a malfunction occurs or adjustment is

required, ﬁrst follow the troubleshooting table in the

back of the Operation Manual to inspect and adjust

the machine yourself� If the problem persists, please

consult your local authorized Brother dealer�

Use this machine only for its intended use as

described in the manual�

Use accessories recommended by the manufacturer

as contained in this manual�

The contents of this manual and speciﬁcations of

this product are subject to change without notice�

For additional product information and updates, visit

our website at www�brother�com

SAVE THESE

INSTRUCTIONS

This machine is intended for household use�

FOR USERS IN COUNTRIES EXCEPT

CENELEC COUNTRIES

This appliance is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a

person responsible for their safety� Children should

be supervised to ensure that they do not play with

the appliance�

FOR USERS IN CENELEC

COUNTRIES

This appliance can be used by

children aged from 8 years and above

and persons with reduced physical,

sensory or mental capabilities or

lack of experience and knowledge

if they have been given supervision

or instruction concerning use of

the appliance in a safe way and

understand the hazards involved�

Children shall not play with the

appliance� Cleaning and user

maintenance shall not be made by

children without supervision�

FOR USERS IN THE

UK, EIRE, MALTA AND

CYPRUS ONLY

IMPORTANT

• In the event of replacing the plug fuse, use a fuse

approved by ASTA to BS 1362, i�e� carrying the

mark, rating as marked on plug�

• Always replace the fuse cover� Never use plugs with

the fuse cover omitted�

• If the available electrical outlet is not suitable for

the plug supplied with this equipment, you should

contact your authorized Brother dealer to obtain the

correct lead�

4

Names of Machine Parts

Main parts

A

I

G

H

B

C

D

E

F

1

3

2

5

6

7

8

9

0

4

1 Bobbin winder (page 8)

2 Spool pin (page 7)

3 Hole for extra spool pin (page 14)

4 Thread tension dial (page 17)

5 Thread guide (pages 8, 10)

6 Thread take-up lever (page 10)

7 Thread cutter (page 16)

8 Flat bed attachment with accessory compartment

(page 4)

9 Operation buttons (page 4)

0 Operation panel (page 6)

A Handwheel

This is used to manually raise and lower the needle�

B Air vent

This vent allows the air surrounding the motor to circulate�

Do not cover the air vent while the machine is being

used�

C Main power switch (page 6)

D Power supply jack (page 6)

E Foot controller (page 6)

F Foot controller jack (page 6)

G Presser foot lever (pages 8, 9, 16)

H Feed dog position switch (page 21)

I Handle

Carry the machine by its handle�

Needle and presser foot section

2

1

3

4

5

6

7

0

9

8

A

1 Needle threader (page 10) ★

2 Buttonhole lever (page 20) ★

3 Presser foot holder (page 15)

4 Presser foot holder screw (page 15)

5 Presser foot

The presser foot applies pressure consistently on the fabric

as the sewing takes place� Attach the appropriate presser

foot for the selected stitching�

6 Feed dogs

The feed dogs feed the fabric in the sewing direction�

7 Quick-set bobbin (page 11)

★

8 Bobbin cover (page 8)

9 Needle plate

The needle plate is marked with guides for sewing straight

seams�

0 Needle bar thread guide (page 10)

A Needle clamp screw

Operation buttons

The operation buttons differ depending on the

machine model�

1

2

3

4

1 Reverse/Reinforcement stitch button (page 16)

Reverse stitches are sewn by keeping this button pressed

down to sew in the opposite direction�

2 “Start/Stop” button

★

Press this button to start or stop sewing�

3 Needle position button

★

Press this button to raise or lower the needle� Pressing the

button twice sews one stitch�

4 Sewing speed controller

★

Slide this controller to adjust the sewing speed� The

controller also sets the maximum sewing speed of the foot

controller�

Flat bed attachment

Accessories such as presser foot, bobbins, and needles

can be stored inside the ﬂat bed attachment�

Slide the attachment to the left to open it�

Note

• Before storing accessories inside the flat bed

attachment, put accessories in a kind of zipper

plastic bags� If accessories are not in a bag, they

may fall out, and be lost or damaged�

★

: Only for some models�

5

Accessories

Included accessories

For the included accessories and their part codes for

your machine, refer to the additional sheet “Included

Accessories”�

Optional accessories

The following are available as optional accessories to

be purchased separately�

1� 2� 3�

4� 5� 6�

7� 8� 9�

10� 11�

No� Part Name

Part Code

Americas Europe

China

Others

1 Walking foot SA140 F033N:

XG6623-001

F033CN

F033N

2 Quilting foot SA129 F005N:

XC1948- 052

-

F005N

3 1/4” piecing

foot

SA125 F001N:

XC1944-052

F001CN

F001N

4 Quilting guide SA132 F016N:

XC2215-052

F016CN

F016N

5 Eyelet punch XG7791-001

6 Twin needle

(2/11 needle)

X59296-121

7 Extra spool pin XG3488-001

8 Cleaning brush X59476-051

9 Seam ripper XZ5082-001

10 Bobbin SA156 SFB:

XA5539-151

-

SFB

11 Wide table SAWT7 W T17:

D01LFJ-001

W T17CN

W T17AP

Memo

• To obtain optional accessories or other accessories

available, contact your authorized Brother dealer

or visit our site http://s�brother/cpkag/� Always use

accessories recommended for this machine�

Using Your Machine

WARNING

• Use only regular household electricity for

the power source� Using other power sources

may result in ﬁre, electric shock, or damage

to the machine�

• Make sure that the power plugs are ﬁrmly

inserted into the electrical outlet and

the power supply jack on the machine�

Otherwise, a ﬁre or electric shock may

result�

• Do not insert the power plug into an

electrical outlet that is in poor condition�

• Turn off the main power and remove the plug

in the following circumstances:

· When you are away from the machine

· After using the machine

· When the power fails during use

· When the machine does not operate correctly

due to a bad connection or a disconnection

· During electrical storms

CAUTION

• Use the power cord included with this

machine�

• Do not use extension cords or multi-plug

adapters with many other appliances plugged

in to them� Fire or electric shock may result�

• Do not touch the plug with wet hands�

Electric shock may result�

• When unplugging the machine, always turn

off the main power ﬁrst� Always grasp the

plug to remove it from the outlet� Pulling on

the cord may damage the cord, or lead to ﬁre

or electric shock�

• Do not allow the power cord to be cut,

damaged, modiﬁed, forcefully bent, pulled,

twisted, or bundled� Do not place heavy

objects on the cord� Do not subject the cord

to heat� These may damage the cord and cause

ﬁre or electric shock� If the cord or plug is

damaged, take the machine to your authorized

dealer for repairs before continuing use�

• Unplug the power cord if the machine is

not to be used for a long period of time�

Otherwise a ﬁre may result�

• (For U�S�A� only)

This appliance has a polarized plug (one

blade wider than the other)� To reduce the

risk of electrical shock, this plug is intended

to ﬁt in a polarized electrical outlet only one

way�

If the plug does not ﬁt fully in the electrical

outlet, reverse the plug� If it still does not ﬁt,

contact a qualiﬁed electrician to install the

proper electrical outlet� Do not modify the

plug in any way�

6

Power supply

1

Insert the plug into a household electrical outlet�

1

2

Turn on the machine�

Press the “I” mark on the main

power switch to turn on the main

power, sewing light, and LCD�

To turn off the machine, press

the “O” mark on the main power

switch�

ON

OFF

X

The machine will make a sound� This is not a

malfunction�

Foot controller

Insert�

CAUTION

• When inserting the foot controller plug,

be sure to turn off the machine in order to

prevent the machine from accidentally being

started�

Slowly depress the foot

controller to start sewing,

and adjust the sewing

speed by changing the

pressing force�

Slower

Faster

Note

• (For U�S�A� only)

Foot controller: Model T

This foot controller can be used on the machine

with product code 888-N00/N02/N20/N22/

N40/N42� The product code is mentioned on the

machine rating plate�

• When the foot controller is connected,

(“Start/

Stop” button) is disabled�

★

Operation panel

5 3

42

1

6

1 LCD (Liquid crystal display)

The selected stitch (1), presser foot that should be used

(2), stitch length in millimeters (3), stitch width in

millimeters (4), needle stop position (5), and single/twin

needle mode (6) are displayed�

2 Stitch selection keys (page 15)

Press keys to change the stitch pattern�

3 Stitch length keys (page 15)

Press keys to change the stitch length of the selected stitch

pattern�

4 Stitch width keys (page 15)

Press keys to change the stitch width of the selected stitch

pattern�

Settings/Functions

You can change settings of the following functions�

The settings are stored even when the power switch is

turned off�

No� Function

1 Needle stop position

2 Initial needle position (left / middle (center))

3 Operation beep ★

4 Maximum sewing speed

5 Automatic reverse / reinforcement stitching

6 Needle mode (single needle / twin needle)

7 Stitch adjustment ★

1

2 6

3

4

5

7

1 Changing the needle stop position

You can change the needle stop position to either

the lowered (in the fabric) or raised position�

(Default: Lowered position)

1

Turn off the machine�

2

Holding down 1, turn on the machine�

3

After the machine has turned on, release 1 �

X

The needle stop position is changed�

: Lowered position

: Raised position

★

: Only for some models�

7

2 Changing the initial needle position

You can change the stitch selected when the

machine is turned on to either

“straight stitch

(left needle position)” or

“straight stitch (middle

(center) needle position)”� (Default:

)

1

Turn off the machine�

2

Holding down 2, turn on the machine�

3

After the machine has turned on, release 2 �

X

The initial needle position is changed�

The currently selected stitch can be conﬁrmed

by the stitch number in the LCD�

3 Turning on/off the operation beep ★

You can turn on/off the operation beep�

(Default: On)

1

Turn off the machine�

2

Holding down 3, turn on the machine�

3

After the machine has turned on, release 3 �

X

The operation beep setting is changed�

4 Changing the maximum sewing speed

You can change the maximum sewing speed to

either the standard or slower speed�

(Default: Standard speed mode)

When the slower speed mode is selected, the

maximum speed adjusted with the sewing speed

controller becomes slower� ★

1

Turn off the machine�

2

Holding down 4, turn on the machine�

3

After the machine has turned on, release 4 �

X

The maximum sewing speed is changed�

l : Slower speed mode

: Standard speed mode

5 Turning on/off the automatic reverse/

reinforcement stitching

You can set the machine to automatically sew

reverse or reinforcement stitches at the beginning

and end of stitching� (Default: Off)

1

Turn off the machine�

2

Holding down 5, turn on the machine�

3

After the machine has turned on, release 5 �

X

The automatic reverse/reinforcement stitching is

turned on or off�

l : On

: Off

*

For details, refer to "Automatic reverse/reinforcement

stitching" (page 17)�

6 Changing the needle mode

You can change the needle mode to either the

single or twin needle mode�

(Default: Single needle mode)

1

Turn off the machine�

2

Holding down 6, turn on the machine�

3

After the machine has turned on, release 6 �

X

The needle mode is changed�

: Single needle mode

: Twin needle mode

*

For details, refer to "Sewing with the twin needle" (page

13)�

7 Stitch adjustment ★

With some stitches, a stitch pattern may turn out

poorly depending on the type of fabric� In such a

case, you can make adjustments� (Default: 0)

1

Turn off the machine�

2

Holding down 7, turn on the machine�

3

After the machine has turned on, release 7 �

X

The machine turns into the stitch pattern

adjustment mode�

*

For details, refer to "Making Adjustment" (page 23)�

Threading the Machine

Winding/Installing the bobbin

CAUTION

• Make sure the power is off while threading

the machine� If you accidentally step on the

foot controller and the machine starts to sew,

you could be injured�

• Be sure to use the

included bobbins

(part code: SA156,

SFB: XA5539-151) or

the same type�

SA156 is Class 15 type bobbin�

11�5 mm (7/16 inch)

1

Pull up the spool pin as far as

possible, and put a spool of

thread on this pin�

Make sure that the thread

unwinds as shown�

CAUTION

• If the spool of thread is not in the right place,

the thread may tangle on the spool pin�

★

: Only for some models�

8

2

Pass the thread under the thread guide and

around the pretension disk, front to back�

Pretension disk

3

Passing the thread through a hole on the bobbin,

set the bobbin on the bobbin winder shaft, and

then slide the shaft to the right�

Make sure the notch ﬁts the projection�

Bobbin winder shaft

Projection

Notch

Memo

• Checking the orientation of the bobbin will

be helpful in later procedures� By placing

the bobbin into the bobbin case in the same

orientation that it was on the bobbin winder

shaft, the bobbin can be installed with the

correct winding direction of the bobbin thread�

The “b” mark on one side of the bobbin

included with this machine can be used as a

reference�

Bobbin case

4

Turn on the machine�

5

While holding the end of the thread, start the

machine to wind the thread around the bobbin a

few times�

or

Depress

gently�

7-8 cm

★

6

Stop the machine and trim the excess thread�

Release�

or

★

7

Slide the sewing speed controller to adjust the

bobbin winding speed� ★

Slower

★

Faster

8

Start the machine�

Depress�

or

★

Note

• We recommend winding stretch thread, such as

transparent nylon thread, at a low speed since

the thread may stretch�

9

When the bobbin seems full and

begins spinning slowly, stop the

machine�

10

Cut the thread, slide the bobbin winder shaft to

the left and remove the bobbin�

CAUTION

• Make sure you follow the instructions

carefully� If you do not cut the thread

completely and the bobbin is wound, when

the thread runs low, it may tangle around the

bobbin and cause the needle to break�

• Not winding the bobbin

properly may cause the

thread tension to loosen,

and may break the needle�

11

Raise the needle to its highest position, and then

raise the presser foot lever�

Turn toward you�

★

or

12

Turn off the machine�

13

Open the bobbin cover�

ON

OFF

★: Only for some models�

9

14

Put the bobbin in, hold the end of the thread,

push the bobbin down with your ﬁnger, and

then pass the thread though the slit as shown�

Hold the bobbin�

Counterclockwise

*

Follow this instruction so that the thread is correctly

inserted through the tension spring of the bobbin

case�

 For models equipped with the quick-set

bobbin ★

Feed the end of the thread through the slit,

and then pull the thread to cut it�

Cutter

Slit for the quick set bobbin

*

The thread feeding direction is indicated by

arrows on the needle plate�

X

You can begin sewing without drawing up the

bobbin thread� When pulling up the bobbin

thread before sewing, refer to “Drawing up the

bobbin thread” (page 11)�

CAUTION

• Be sure to hold down the bobbin with

your ﬁnger and unwind the bobbin thread

correctly, otherwise the thread may break or

the thread tension will be incorrect�

15

Reattach the bobbin cover�

*

Make the end of the thread come out from the left

side of the cover�

n For models equipped with the cutter ★

1

Follow steps 1 to 2 of “Winding/Installing the

bobbin”�

2

Set the bobbin on the bobbin winder shaft,

and then slide the shaft to the right�

Make sure the notch ﬁts

the projection�

Notch

Projection

Slit (cutter)

*

Check the installation orientation of the bobbin by

using the "b" mark on one side of the bobbin as a

reference� When placing the bobbin in the bobbin

case, be sure to place it in the same orientation�

3

Slit

Wind ﬁve or six

times�

Pull the thread�

The thread is cut at the

slit�

CAUTION

• Be sure to cut the thread as described� If

the bobbin is wound without cutting the

thread using the cutter built into the slit

in the bobbin winder seat, the thread may

become tangled in the bobbin or the needle

may bend or break when the bobbin thread

starts to run out�

4

Turn on the machine�

5

Follow steps 7 to 15 of “Winding/Installing

the bobbin”�

Upper threading

CAUTION

• Make sure you thread the machine properly�

Otherwise, the thread could tangle and break

the needle�

• Never use a thread weight of 20 or lower�

• Use the needle and the thread in the correct

combination� (page 12)

1

Raise the presser foot lever�

★: Only for some models�

10

2

Raise the needle to its highest position�

Turn toward you so that this mark

points up to the highest position�

Press once or twice�

or

★

3

If the power of the machine is on, turn it off�

4

Pull up the spool pin as far as

possible, and put a spool of

thread on this pin�

Make sure that the thread

unwinds as shown�

5

Pass the thread through the thread channel in the

order shown below�

*

Follow the numbered path printed on the machine�

Thread take-up lever

Make sure that the thread

unwinds as shown�

6

Slide the thread behind

the needle bar thread

guide�

7

Insert the thread through the eye of the needle

from front to back, and then pass the thread

under the presser foot�

10 cm (4 inches)

n Using the needle threader ★

CAUTION

• The needle threader can only be used with

home sewing machine needles size 75/11-

100/16� If you are using transparent nylon

monoﬁlament thread, you can only use

needles in the range of 90/14-100/16�

• You cannot use the needle threader if you

are using decorative threads or special

needles, such as the twin needle and wing

needle� If you are using those types of

threads or needles, thread the eye of the

needle by hand� Make sure the main power

switch is off when threading the needle�

1

Follow steps 1 to 6 of “Upper threading”�

2

a) Pass the thread behind the guide (1), and

insert the thread into the slit of the thread

guide disk (2) ﬁrmly� Next, cut the thread

with the thread cutter (3)�

2

1

3

Thread cutter

Guide

Thread guide

disk

b) Lower the presser foot lever�

c) Lower the needle threader lever fully until

it stops (4), and push it back slowly until it

stops (5)�

5

4

Hook

*

Make sure that the hook passes through the

eye of the needle, and catch the thread�

a) Lower the presser foot lever�

Needle bar thread guide

★: Only for some models�

11

b) While lowering the needle threader lever

fully (1), hook the thread onto the guide

(2)� Next, push back the needle threader

lever until it stops (3), and pass the thread

in front of the needle� Make sure that the

thread is under the hook that has come

through the eye of the needle and the hook

catches the thread� (4)�

1

2

3

4

3

Return the needle threader lever to the front

slowly, and then release the lever slowly�

4

Raise the presser foot lever�

5

Pull the loop of the thread, and pass the end

of the thread as illustrated below�

10 cm

(4 inches)

Drawing up the bobbin thread

1

Refer to “Upper threading” (page 9) to thread

the machine with the upper thread and thread

the needle�

2

Follow steps 11 to 13 of “Winding/Installing the

bobbin” (page 7) for installing the bobbin and

to insert the bobbin into the bobbin case�

3

Pass the thread along the slit in the direction of

the arrow, and leave it there without cutting it�

4

Lightly hold the end of the upper thread�

Upper thread

5

While holding the end of the upper thread, lower

and raise the needle to draw up the bobbin

thread�

Turn towards you one full turn until

this mark points up to the highest

position�

Press twice�

or

★

6

Pull on the upper thread to draw up the bobbin

thread�

Next, pull out about 10 cm (4 inches) of both

threads toward the back under the presser foot�

Upper thread

Bobbin thread

n For models equipped with the quick-set

bobbin

★

You can begin sewing without drawing up the

bobbin thread� (page 9)

Note

•

When you sew gathers or ﬁnish up the threads

at the beginning of sewing, draw up the bobbin

thread�

★

: Only for some models�

12

Fabric/Thread/Needle Combination

• Needles that can be used with this machine: Home sewing machine needles (size 65/9 - 100/16)

* The larger the number, the larger the needle� As the numbers decrease, the needles get ﬁner�

• Thread that can be used with this machine: 30 - 90 weight

* Never use thread of 20 weight or lower� It may cause machine to malfunction�

* The smaller the number, the heavier the thread� As the numbers increase, the thread gets ﬁner�

• The machine needle and thread that should be used depends on the type and thickness of the fabric� Refer to

the following table when choosing the thread and needle appropriate for the fabric that you wish to sew�

- The combinations shown in the table provide a general guideline� Be sure to sew trial stitches on the actual

number of layers and type of fabric to be used in your project�

- The machine needles are consumables� For safety and best results, we recommend replacing the needle

regularly� For details on when to replace the needle, refer to “Checking the needle” (page 13)�

• In principle, use a ﬁne needle and thread with lightweight fabrics, and a larger needle and heavier thread with

heavyweight fabrics�

• Select a stitch appropriate for the fabric, and then adjust the stitch length� When sewing lightweight fabrics,

make the stitch length ﬁner (shorter)� When sewing heavyweight fabrics, make the stitch length coarser (longer)�

(page 15)

When sewing stretch fabrics, refer to “Sewing guide” (http://s�brother/cmkag/)�

Fabric Type/Application

Thread

Size of needle

Stitch length

mm (inch)

Type Weight

Lightweight

fabrics

Lawn, georgette, challis,

organdy, crepe, chiffon, voile,

gauze, tulle, lining, etc�

Polyester

thread

60 - 90

65/9 - 75/11

Fine stitches

1�8 - 2�5

(1/16 - 3/32)

Cotton thread,

Silk thread

50 - 80

Medium weight

fabrics

Broadcloth, taffeta, gabardine,

ﬂannel, seersucker, double

gauze, linen, terry cloth, wafﬂe

weave, sheeting, poplin, cotton

twill, satin, quilting cotton, etc�

Polyester

thread

60 - 90

75/11 - 90/14

Regular stitches

2�0 - 3�0

(1/16 - 1/8)

Cotton thread,

Silk thread

50 - 60

Heavyweight

fabrics

Denim (12 ounces or more),

canvas, etc�

Polyester

thread,

Cotton thread

30 100/16

Coarse stitches

2�5 - 4�0

(3/32 - 3/16)

Denim (12 ounces or more),

canvas, tweed, corduroy, velour,

melton wool, vinyl-coated

fabric, etc�

Polyester

thread

60

90/14 - 100/16

Cotton thread,

Silk thread

30 - 50

Stretch fabrics

(knit fabrics, etc�)

Jersey, tricot, T-shirt fabric,

ﬂeece, interlock, etc�

Polyester thread,

Cotton thread,

Silk thread

50

Ball point needle

75/11 - 90/14

Setting appropriate for

the fabric thickness

For top-stitching

Polyester thread,

Cotton thread

30 90/14 - 100/16

Setting appropriate for

the fabric thickness

50 - 60 75/11 - 90/14

n Transparent nylon thread

Use a home sewing machine topstitching needle, regardless of the fabric or thread�

n Sewing decorative stitch patterns (needles and threads) ★

When sewing lightweight, medium weight or stretch fabrics, use a ball point needle (gold colored) 90/14� When

sewing heavyweight fabrics, use a home sewing machine needle 90/14�

In addition, #50 to #60 thread should be used�

CAUTION

• The appropriate fabric, thread and needle combinations are shown in the preceding table� If the

combination of the fabric, thread and needle is not correct, particularly when sewing heavy fabrics

(such as denim) with thin needles (such as 65/9 to 75/11), the needle may bend or break� In addition, the

stitching may be uneven or puckered or there may be skipped stitches�

★

: Only for some models�

13

Needle

CAUTION

• Use recommended home sewing machine

needles�

• Never use bent needles� Bent needles can

easily break, possibly resulting in injuries�

Checking the needle

Before using the needle, place the ﬂat side of the

needle on a ﬂat surface and check that the distance

between the needle and the ﬂat surface is even�

Flat side Needle type marking

Flat surface

Even

Not even

Note

• The machine needles are consumables� Replace the

needle in cases such as those described below�

- If an unusual sound is produced when the needle

enters the fabric� (The tip of the needle may be

broken or dull�)

- If stitches are skipped� (The needle may be bent�)

- Generally, after completing one project, such as a

piece of clothing�

Replacing the needle

CAUTION

• Before replacing the needle, be sure to turn

off the machine, otherwise injuries may

occur if the foot controller (or

(“Start/

Stop” button) ★) is accidentally pressed and

the machine starts sewing�

1

Raise the needle to its highest position�

Turn toward you so that this mark

points up to the highest position�

Press once or twice�

or

★

2

Remove the presser foot� (page 14)

3

Turn off the machine�

4

Before replacing the needle, cover the hole in the

needle plate with fabric or paper to prevent the

needle from falling into the machine�

5

Remove the needle�

1

2

*

Do not apply strong

force�

Loosen�

Screwdriver

6

Install another needle�

Make the ﬂat side

face back�

Tighten�

Insert until the needle touches this part�

7

Attach the presser foot� (page 15)

CAUTION

• Be sure to install the needle as described

above, otherwise the needle may break or

damage may result�

Sewing with the twin needle

You can sew with the twin needle and

two upper threads� You can use the

same color or two different colors of

thread for making decorative stitches�

For details on the stitches that can be sewn with the

twin needle, refer to “Stitch chart”

(http://s�brother/cmkag/)�

*

The twin needle and the extra spool pin are sold separately

with some models�

CAUTION

• Use the twin needle that has been made for

this machine (part code: X59296-121)�

• Do not sew with bent needles� The needle

could break and injure you�

• You cannot use the needle threader to thread

the twin needle� Instead, thread the twin

needle by hand, from front to back� Using the

needle threader may damage the machine�

★: Only for some models�

14

CAUTION

• When using the twin needle, be sure to select

an appropriate stitch, otherwise the needle

may break or the machine may be damaged�

• Select a stitch width of 5�0 mm (3/16 inch) or

less, otherwise the needle may break or the

machine may be damaged�

• After adjusting the stitch width,

slowly turn the handwheel toward you

(counterclockwise) and check that the needle

does not touch the presser foot� If the needle

hits the presser foot, the needle may bend or

break�

• When using the twin needle, be sure to

attach zigzag foot “J”, otherwise the needle

may break or the machine may be damaged�

• When changing the sewing direction, be sure

to raise the needle before turning the fabric�

If the fabric is turned while the needle is

lowered, the needle may bend or break�

1

Attach zigzag foot “J”�

2

Attach the twin needle in the same way as a

single needle� (page 13)

3

Put the extra spool pin in the hole on the top of

the machine, and then put the second spool of

thread onto the extra spool pin�

Second spool

First spool

Extra

spool pin

4

Thread the left needle by using the thread from

the ﬁrst spool in the same way as for normally

threading the machine (for a single needle)�

(page 9)

*

Be sure to pass the thread behind the needle

bar thread guide�

5

Thread the right needle by using the thread from

the second spool in the same way as for normally

threading the machine (for a single needle)�

(page 9)

*

Be sure to thread the right needle from front to

back�

Needle bar

thread guide

6

Turn the machine into the twin needle mode�

(page 7)

7

Select a stitch and start sewing�

*

If you select an inappropriate stitch with the

twin needle, an error message appears� Select an

appropriate stitch�

Note

• You cannot use the needle threader to thread

the twin needle� Instead, thread the twin needle

by hand, from front to back� Using the needle

threader may damage the machine�

★

Replacing the Presser Foot

CAUTION

• Before replacing the presser foot, be sure to

turn off the machine, otherwise injuries may

occur if the foot controller (or

(“Start/

Stop” button)

★

) is accidentally pressed and

the machine starts sewing�

• Always use the correct presser foot for the

stitch pattern you have chosen� If you use

the wrong presser foot, the needle may strike

the presser foot and bend or break, and may

cause injury�

• Use the presser feet that have been designed

to be used with this machine�

Replacing the presser foot

1

Raise the needle to its highest position�

Turn toward you so that this mark

points up to the highest position�

Press once or twice�

or

★

2

Turn off the machine, then raise the presser foot

lever�

3

Remove the presser foot�

*

Refer to one of the procedure depending on the type of

your machine�

Press the black button

to release the presser

foot�

Pull the presser foot

vertically downward�

Black button

or

★: Only for some models�

15

4

Place another foot so that the groove and pin

align�

1

2

Groove

Note

• The presser foot to be used with each stitch

appears in the LCD�

5

Slowly lower the presser foot lever so that the

presser foot pin snaps into the groove�

Removing the presser foot holder

Remove the presser foot holder when installing a

presser foot that does not use the presser foot holder,

such as the walking foot * and quilting foot *�

*

: Sold separately with some models�

Screwdriver

Presser foot

holder

Loosen�

or

Note

• When attaching the presser foot holder, hold the

presser foot holder in place and tighten the screw�

Sewing Basics

CAUTION

• While the machine is in operation, pay

special attention to the needle location�

In addition, keep your hands away from

all moving parts such as the needle and

handwheel, otherwise injuries may occur�

• Do not pull or push the fabric too hard while

sewing, otherwise injuries may occur or the

needle may break�

• Never use bent needles� Bent needles can

easily break, possibly resulting in injuries�

• Make sure that the needle does not strike

basting pins, otherwise the needle may break

or bend�

Selecting the stitch

Press the stitch selection keys to change the stitch

number�

a b

Selected stitch Presser foot that should be used

Stitch selection keys

1 Changes the tens digit of the

stitch number�

2 Changes the ones digit of the

stitch number�

Setting the stitch length and stitch

width

• Press + or - of the stitch length keys to increase or

reduce the stitch length�

• Press + or - of the stitch width keys to increase or

reduce the stitch width�

Memo

• If a straight stitch or triple stretch stitch is

selected, changing the stitch width changes the

needle position�

Increasing the width moves the needle to the

right; reducing the width moves the needle to

the left�

Note

• The setting value changes until it reaches the

maximum or minimum value�

•

around or disappears when changed from

the standard setting�

• If “--” appears to the right of

, the stitch width

cannot be adjusted�

16

CAUTION

• After adjusting the stitch width,

slowly turn the handwheel toward you

(counterclockwise) and check that the needle

does not touch the presser foot� If the needle

hits the presser foot, the needle may bend or

break�

• If the stitches are bunched together, increase

the stitch length� Continuing to sew with the

stitches bunched together may result in the

needle bending or breaking�

Starting to sew

Baste the fabric before starting to sew�

1

Raise the needle to its highest position�

Turn toward you so that this mark

points up to the highest position�

Press once or twice�

or

★

2

Raise the presser foot lever�

3

Set the fabric under the presser foot, and then

hold the fabric and the end of the thread with

your left hand�

4

Lower the needle to the starting point of the

stitching�

Turn toward you�

or

★

5

Lower the presser foot lever�

6

Adjust the sewing speed�

★

7

Start sewing�

*

Guide the fabric lightly by hand�

Depress�

or

★

8

Stop sewing�

Release�

or

★

9

Raise the needle, and then raise the presser foot

lever�

Turn toward you�

or

★

10

Pull the fabric and cut the threads�

Thread cutter

Sewing reverse/reinforcement

stitches

Reverse/reinforcement stitches are generally necessary

at the beginning and end of sewing�

With reinforcement stitches, 3 to 5 stitches are sewn at

the same place� With reverse stitches, the stitching is

sewn in the opposite direction�

Depending on the selected stitch, reverse or

reinforcement stitches are sewn while

(Reverse/

Reinforcement stitch button) is pressed continuously�

Memo

• When any of the reverse stitch patterns is selected,

pressing

(Reverse/Reinforcement stitch button)

will sew reverse stitches� When any other stitch is

selected, pressing

(Reverse/Reinforcement stitch

button) will sew reinforcement stitches�

Reverse stitch pattern

Reinforcement stitch

Reverse/

Reinforcement

stitch button

Reverse stitch

★: Only for some models�

17

Automatic reverse/reinforcement

stitching

Turn on the automatic reverse/reinforcement stitching

function before sewing, and the machine will

automatically sew reinforcement stitches (or reverse

stitches, depending on the stitch pattern) at the

beginning and end of sewing�

1

Turn on the automatic reverse/reinforcement

stitching� (page 7)

2

Select a stitch�

3

Set the fabric in the start position and start

sewing�

Reverse stitches (or reinforcement stitches)

X

The machine will automatically sew reverse stitches (or

reinforcement stitches) and then continue sewing�

Note

• You can pause or resume sewing by pressing

(“Start/Stop” button) while sewing� ★

4

Once you have reached the end of the stitching,

press

(Reverse/Reinforcement stitch button)�

Reverse stitches (or reinforcement stitches)

X

The machine will sew reverse stitches (or

reinforcement stitches) and stop�

Thread tension

The thread tension will affect the quality of your

stitches� You may need to adjust it when you change

fabric or thread�

Note

• We recommend that you do a test sample on scrap

of a fabric before you start to sew�

n Correct tension

*

Too much or too little tension will weaken your seams

or cause puckers on your fabric�

Wrong side

Right side

Upper thread

Bobbin thread

n Upper tension is too tight

Note

• If the bobbin thread was incorrectly threaded,

the upper thread may be too tight� In this case,

refer to “Winding/Installing the bobbin” (page

7) and rethread the bobbin thread�

0

1

2

3

4

5

6

7

8

9

Loops will appear on the

right side of the fabric�

Solution

Reduce the upper thread

tension�

n Upper tension is too loose

Note

• If the upper thread was incorrectly threaded,

the upper thread may be too loose� In this case,

refer to “Upper threading” (page 9) and

rethread the upper thread�

0

1

2

3

4

5

6

7

8

9

Loops appear on the

wrong side of the fabric�

Solution

Increase the upper thread

tension�

Note

• If the upper thread is not threaded correctly or

the bobbin is not installed correctly, it may not be

possible to set the correct thread tension� If the

correct thread tension cannot be achieved, rethread

the upper thread and insert the bobbin correctly�

Utility Stitches

You can see the “Stitch chart” from

“ http://s�brother/cmkag/ ”�

Overcasting stitches

Sew overcasting stitches along the edges of cut fabric

to prevent them from fraying�

1

Attach overcasting foot “G”�

2

Select a stitch�

*

Stitches may differ depending on the model� Check

stitch selections on the machine's body, and then

select the stitch number�

★: Only for some models�

18

CAUTION

• When using overcasting foot “G”, be sure

to select a stitch that can be used with

overcasting foot “G”� If you sew with the

incorrect stitch, the needle may hit the

presser foot, bending the needle or damaging

the presser foot�

3

Position the fabric with the edge of the fabric

against the presser foot guide, and then lower the

presser foot lever�

Presser foot guide

4

Rotate the handwheel toward you

(counterclockwise)� Check that the needle does

not touch the presser foot�

The needle should not touch

the presser foot center bar�

5

Sew with the edge of the fabric against the

presser foot guide�

Needle drop point

CAUTION

• Be sure to pull the fabric backward after

ﬁnished sewing� If you pull the fabric toward

side or forward, the presser foot pin may be

damaged�

• If thread is tangled on the presser foot,

remove the entangled thread, and then raise

the presser foot lever to remove the presser

foot� If the presser foot is raised while

entangled with thread, the presser foot may

be damaged�

6

Stop sewing when you are ﬁnished, and raise the

presser foot and needle to pull the fabric under

the presser foot towards the back of the machine�

Blind hem stitching

Secure the lower edge of skirts and pants with a blind

hem�

Memo

• When the size of cylindrical pieces is too small to

slide onto the arm or the length is too short, the

fabric will not feed and desired results may not be

achieved�

1

Turn the skirt or pants inside out�

a

b

c

1 Wrong side of fabric

2 Right side of fabric

3 Lower edge of fabric

2

Fold the lower edge of fabric to the desired length

to be hemmed and then press�

d

b

a

c

1 Wrong side of fabric

2 Right side of fabric

3 Lower edge of fabric

4 Desired length for hem

<Seen

from the side>

3

Using tailor’s chalk, mark the fabric about 5 mm

(3/16 inch) from the edge of the fabric, and then

baste it�

b

a

ce

f

d

1 Wrong side of fabric

2 Right side of fabric

3 Lower edge of fabric

4 Desired length for hem

5 5 mm (3/16 inch)

6 Basting

4

Fold back the fabric inside along the basting�

a

c

f

e

a

b

g

d

1 Wrong side of fabric

2 Right side of fabric

3 Lower edge of fabric

4 Desired length for hem

5 5 mm (3/16 inch)

6 Basting

7 Basting point

5

Unfold the edge of fabric, and position the fabric

with the wrong side facing up�

a

b

f

c

a

c

d

a

f

a

b

e

1 Wrong side of fabric

2 Right side of fabric

3 Edge of fabric

4 Desired edge of hem

5 Basting point

6 Basting

19

6

Attach blind stitch foot “R”�

7

Select a stitch�

*

Stitches may differ depending on the model� Check

stitch selections on the machine's body, and then

select the stitch number�

8

Remove the ﬂat bed attachment to use the free

arm�

9

Slide the item that

you wish to sew

onto the free arm,

make sure that

the fabric feeds

correctly, and then

start sewing�

10

Position the fabric with the edge of the folded

hem against the presser foot guide, and then

lower the presser foot lever�

Fold of hem

Presser foot guide

Wrong side

of fabric

11

Adjust the stitch width until the needle slightly

catches the fold of the hem� (page 15)

Needle drop point

When you change the needle drop point, raise

the needle, and then change the stitch width�

*

To make ﬁne adjustments to the needle drop point,

adjust the stitch width setting�

Memo

• Blind hem stitches cannot be sewn if the left

needle drop point does not catch the fold� If the

needle catches too much of the fold, the fabric

cannot be unfolded and the seam appearing

on the right side of the fabric will be very large,

leaving an unattractive finish�

12

Sew with the fold of the hem against the presser

foot guide�

13

Stop sewing when you are ﬁnished, and raise

the presser foot and needle to pull the fabric

under the presser foot towards the back of the

machine�

Note

• Be sure to pull the fabric towards the back of

the machine after sewing� If you pull the fabric

toward side or forward, the presser foot may be

damaged�

14

Remove the basting stitching and turn the fabric

with the right side facing out�

Wrong side

of fabric

Right side

of fabric

Buttonhole sewing

The maximum buttonhole length is about 28 mm

(1-1/8 inches) (diameter + thickness of the button)�

Buttonholes are sewn from the front of the presser foot

to the back, as shown below�

1 Reinforcement stitching

*

Stitches may differ depending on the model� Check

the stitches lineup on your machine’s body, and then

select the stitch number�

The part names of buttonhole foot “A”, which is used

to create buttonholes, are indicated below�

e

bacd

A

1 Button guide plate

2 Presser foot scale

3 Presser foot pin

4 Marks on buttonhole foot

5 5 mm (3/16 inch)

Note

• Before sewing buttonholes, check the stitch length

and width by sewing a trial buttonhole on a scrap

piece of fabric used for your project�

20

1

Use chalk to mark on the fabric the position and

length of the buttonhole�

Marks on fabric

Buttonhole sewing

2

Pull out the button guide plate of buttonhole foot

“A”, and then insert the button that will be put

through the buttonhole�

*

If the button does not ﬁt in the button

guide plate

Add together the diameter and thickness of the

button, and then set the button guide plate to the

calculated length�

a

b

c

1 Presser foot scale

2 Length of buttonhole

(diameter + thickness

of button)

3 5 mm (3/16 inch)

Example: For a button with a diameter of 15 mm

(9/16 inch) and a thickness of 10 mm (3/8 inch),

the button guide plate should be set to 25 mm (1

inch) on the scale�

10 mm (3/8 inch)

15 mm (9/16 inch)

X

The size of the buttonhole is set�

3

Attach buttonhole foot “A”�

Before attaching the buttonhole foot “A”, pass the

upper thread underneath the presser foot through

the hole�

4

Select a stitch�

*

Stitches may differ depending on the model� Check

stitch selections on the machine's body, and then

select the stitch number�

5

Position the fabric with the front end of the

buttonhole mark aligned with the red marks on

the buttonhole foot, and then lower the presser

foot lever�

A

a

b

c

1 Mark on fabric (front)

2 Red marks on buttonhole

foot

3 Upper thread

Note

• When lowering the presser foot, do not push in

the front of the presser foot, otherwise the bar

tack will not be sewn with the correct size�

6

Pull down the buttonhole lever as far as possible�

Buttonhole lever

The buttonhole lever is positioned behind the

bracket on the buttonhole foot�

Buttonhole lever

Bracket

7

Gently hold the end of the upper thread in your

left hand, and then start sewing�

X

Once sewing is completed, the machine automatically

sews reinforcement stitches, then stops�

8

Raise the needle and presser foot, then remove

the fabric, and then cut the threads�

9

Raise the buttonhole lever to its original position�

10

Insert a pin along the inside of one bar tack at

the end of the buttonhole stitching to prevent

the stitching from being cut�

11

Use the seam ripper to cut towards the pin and

open the buttonhole�

Seam ripper

For keyhole buttonholes, use the eyelet punch

to make a hole in the rounded end of the

buttonhole, and then use the seam ripper to cut

open the buttonhole�

Eyelet punch

Page is loading ...

Brother CS7000X User manual

Brother CS7000X User manual

Related papers

Other documents