Mirabelle A7242OMIRBS Installation guide

www.mirabelleproducts.com

INSTALLATION AND OPERATING MANUAL

READ THESE INSTRUCTIONS COMPLETELY BEFORE INSTALLING THE PRODUCT. FOR PRODUCT OR

INSTALLATION QUESTIONS PLEASE CALL CUSTOMER SERVICE AT 1-800-221-3379.

YOU MUST FOLLOW ALL INSTRUCTIONS IN THIS MANUAL: FAILURE TO DO SO WILL RESULT IN YOUR

ASSUMPTION OF LIABILITY AND WILL VOID WARRANTY AND CAN RESULT IN PRODUCT DAMAGE OR

PERSONAL INJURY.

FAILURE TO USE A SUITABLE SETTING COMPOUND WILL VOID THE WARRANTY.

THIS PRODUCT IS DESIGNED TO BE INSTALLED BY A LICENSED TRADESMAN. LICENSED PLUMBERS AND

ELECTRICIANS SHOULD BE EMPLOYED TO INSURE PROPER INSTALLATION. INSTALLERS ASSUME ALL LIABILITY

FOR THE CORRECT INSTALLATION PROCEDURES.

Only accessories authorized by the manufacturer should be used with this product. This product is designed for

residential use and use by healthy individuals.

IMPORTANT SAFETY INSTRUCTIONS: WARNING! WHEN USING THIS PRODUCT, BASIC PRECAUTIONS SHOULD

ALWAYS BE FOLLOWED. READ AND FOLLOW ALL INSTRUCTIONS PERTAINING TO RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS.

INSTALLER: LEAVE THIS MANUAL FOR HOMEOWNER.

HOMEOWNER: READ THIS MANUAL AND KEEP FOR FUTURE REFERENCE.

TABLE OF CONTENTS

Important Safety Information 1

Recommended Tools and Material 2

Inspection & Testing 2

Electrical Requirements & Information 3

Framing & Installation 5

Rough-in Dimensions 7

Care & Cleaning/Maintenance 9

Operating Instructions 9

Troubleshooting 12

Warranty 12

Cut-Out Templates 13

www.mirabelleproducts.com

3

IMPORTANT SAFETY INSTRUCTIONS

SAVE THIS MANUAL: RETAIN FOR CONSUMER’S USE. READ THESE INSTRUCTIONS

COMPLETELY BEFORE INSTALLING THE PRODUCT: FOR PRODUCT OR INSTALLATION

QUESTIONS PLEASE CALL CUSTOMER SERVICE AT 1-800-221-3379.

YOU MUST FOLLOW ALL INSTRUCTIONS IN THIS MANUAL: FAILURE TO DO SO WILL RESULT

IN YOUR ASSUMPTION OF LIABILITY AND WILL VOID WARRANTY AND CAN RESULT

IN PRODUCT DAMAGE OR PERSONAL INJURY. FAILURE TO USE A SUITABLE SETTING

COMPOUND WILL VOID THE WARRANTY.

THIS PRODUCT IS DESIGNED TO BE INSTALLED BY A LICENSED TRADESMAN. LICENSED

PLUMBERS AND ELECTRICIANS SHOULD BE EMPLOYED TO INSURE PROPER INSTALLATION.

INSTALLERS ASSUME ALL LIABILITY FOR THE CORRECT INSTALLATION PROCEDURES.

Only accessories authorized by the manufacturer should be used with this product.

This product is designed for residential use and use by healthy individuals.

IMPORTANT SAFETY INSTRUCTIONS

WHEN USING THIS PRODUCT, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED.

READ AND FOLLOW ALL INSTRUCTIONS PERTAINING TO RISK OF FIRE, ELECTRIC SHOCK,

OR INJURY.

IMPORTANT SAFETY INSTRUCTIONS

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS

READ AND FOLLOW ALL INSTRUCTIONS!

Risk of personal injury. Do not permit children to use this unit without adult supervision.

Risk of personal injury. Do not operate this unit without the guard over the suction tting.

Risk of electric shock. Do not permit electrical appliances (hair dryer, telephone, radio, etc.)

within 60 inches (1524mm) of this unit.

Risk of hyperthermia and possible drowning. People using medications and/or having adverse

medical history should consult a physician before using this product.

Risk of personal injury. Do not overll unit before entering. Entering tub when lled more than

2/3 can cause overow and slippery conditions. Exercise caution when entering and exiting.

No Food or Alcoholic Beverages. Use of your bathtub immediately after meals is not

recommended. Avoid alcohol consumption before or during bathing. Alcoholic beverages can

cause drowsiness or hyperthermia resulting in loss of consciousness or even drowning.

Pregnancy. If you are or think you may be pregnant, consult your physician before using the

bathtub. Never drop or insert any object into any opening. Use this unit only for its intended use

as described in this manual. Do not use any attachments not recommended by Mirabelle.

This equipment is intended for indoor use only.

WARNING

www.mirabelleproducts.com

4

The unit must be connected only to a supply circuit that is properly protected by a 20 amp ground-fault circuit interrupter (GFCI). Such a GFCI

should be provided by the installer and should be tested on a routine basis. To test the GFCI, push the test button. The GFCI should interrupt

power. Push the reset button. Power should be restored. If the GFCI fails to operate in this manner, the GFCI is defective. If the GFCI interrupts

power to the bathtub without the test button being pushed, a ground current is owing, indicating the possibility of an electric shock. Do not

use this total massage, whirlpool or air bathtub. Disconnect The total massage, whirlpool or air bathtub and have the problem corrected by a

licensed electrician before using.

A pressure wire connector is provided on the exterior of the motor unit to permit connection of a no. 8 AWG solid copper bonding

conductor between this unit and all other electrical equipment and exposed metal in the vicinity, as needed to comply with local

requirements. To reduce the risk of an electric shock, connect this connector to the grounding terminal of your electric service or supply panel

with a conductor equivalent in size to the circuit conductors supplying this unit. Use supply wires that are suitable for 167°F (75°C), including

the temperature rating of the supply conductors to be used. Building materials and wiring should be routed away from the motor/pump or

blower or other heat producing components of this unit.

Recommended Tools and Material

Important Safety Instructions

• Silicone sealant

• Tape measure

• Pencil

• Safety glasses

• Pipe wrench

• Level

• Conventional woodworking

tools and materials

• Drop cloth

• 2x4’s

• Mortar

• Optional: construction adhesive

Inspection and Testing

Each bath arrives ready for installation, completely equipped with the pump and plumbing necessary for operation. However, a drain/

overow kit is required for each bath and it is not included.

The variety of installations for this bath may require framing procedures other than those shown.

Locate studs as required. Ensure roughing-in dimensions (see pg. 11) are proper, plumb, and square.

Inspection:

• Remove the bath from the carton. Retain the shipping carton until satisfactory inspection of the product has been made. Do not lift the bath

by the plumbing at any time; handle by the shell only. All bath units are factory tested for proper operation and watertight connections

prior to shipping.

• Inspect the shell and bathtub components. Should inspection reveal any damage or defect in the nish or visible damage to any

components, do not install the bathtub. Damage or defect to the nish claimed after the bathtub is installed is excluded from the warranty.

• Inspect the tub components for loose ttings.

Testing:

• Prior to installation and before enclosing with wallboard, tile, etc., the bath must be lled with water and operated to check for leaks that

may have resulted from shipping damage or mishandling.

• It is the responsibility of the installer to thoroughly test the tub prior to completing installation. Place the tub on a level surface, ensure

drain is sealed and ll the bathtub with water to the bottom of the overow. Allow water to sit in tub for at least 5 minutes as a static test. If

installing a system tub, plug in the motor/ pump and turn it on. Conrm all features function correctly. Visually inspect all joints for leaks.

DO NOT install tub if any leaks are detected or system functions do not work properly.

www.mirabelleproducts.com

5

Electrical Requirements and Information

ALL CONNECTIONS MUST BE GFCI (Ground Fault Circuit Interrupted) PROTECTED

1. Whirlpool and Total Massage units require dedicated 20 Amp,

120V service.

2. You must provide a receptacle with a 20-amp conguration.

3. See local codes for proper wire size. If not specied, use #12 Copper only wire.

4. Optional In-Line Heater requires its own dedicated 20 amp service.

The unit must be connected to a circuit interrupter (GFCI) provided by the installer. The (GFCI) breaker should be

tested on a routine basis.

To test the (GFCI) breaker, push the test button. The GFCI should interrupt power. To restore power, push the RESET

button. If the GFCI fails to operate in this manner there is ground current owing, indicating the possibility of an

electrical shock. Do not use the unit. Disconnect the unit and have the problem corrected by a qualied service

representative before using.

DANGER

RISK OF ELECTRICAL SHOCK. All pumps and blowers must be connected

to a ground fault circuit interrupter (GFCI) protected outlets. Standard Line

Total Massage units can be operated on a single service. All heaters must be

connected to a ground fault circuit interrupter (GFCI) protected outlets, separate

from the pump and/or blower.

Electrical outlet must be mounted 4” (101mm) above the oor line and 12’’

max (305mm) inside from the edge of the bathtub, or in accordance with local

building and electrical codes.

• Risks of component over heat. Do not use electric extension cord to power

the unit. Operating the pump without enough water in bathtub can cause

permanent damage to the pump/motor.

• If CFGI unit indicates a malfunction, per manufacturer’s instructions, turn OFF

power and do not attempt to use the bathtub until the source of the problem

has been identied and corrected.

www.mirabelleproducts.com

6

Electrical Congurations

TOTAL MASSAGE CIRCUIT WITH OPTIONAL HEATER

PUMP FLOW

CONTROLL VALV E

0.5 AMP

BACK OF 6 BTN CONTROL

PIGGY BLOWER

9.5 AMP

TMS - VARIABLE

CONTROL

TMS-P/TIMER

CONTROL

ON / OFF PUMP

9 AMP

OPTIONAL

120V, 60 HZ

20 AMP GFCI

120V / 20AMP

MALE PLUG

GFCI GFCI

ELECTRICAL

FEED

120V, 60 HZ

20 AMP GFCI

HEATER

AIR SPEED WAVE

SPEEDJETS WAVE

WHIRLPOOL CIRCUIT WITH OPTIONAL HEATER

PUMP FLOW

CONTROLL VALV E

0.5 AMP

TMS-P/TIMER

CONTROL

ON / OFF PUMP

9 AMP

OPTIONAL

HEATER

120V, 60 HZ

20 AMP GFCI

120V / 20AMP

MALE PLUG

GFCI GFCI

ELECTRICAL

FEED

120V, 60 HZ

20 AMP GFCI

BACK OF 3 BUTTON CONTROL

AIR MASSAGE CIRCUIT

PIGGY BLOWER

9.25 AMP

TMS - VARIABLE

CONTROL

120V, 60 HZ

20 AMP GFCI

GFCI GFCI

ELECTRICAL

FEED

120V, 60 HZ

20 AMP GFCI

GFCI GFCI

ELECTRICAL

FEED

BACK OF 3 BUTTON CONTROL

120V, 60 HZ

20 AMP GFCI

GFCI GFCI

ELECTRICAL

FEED

120V, 60 HZ

9.25 AMP

HEATER

PIGGY BLOWER

9.5 AMP

AIR SWITCH

ON / OFF PUMP

9 AMP

AIR SWITCH

CONTROL BOX

PIGGY BLOWER

9.5 AMP

PUMP / MOTOR

120V, 60 HZ

20 AMP GFCI

GFCI GFCI

ELECTRICAL

FEED

AIR SWITCH

BRADENTON & PROVINCETOWN TOTAL MASSAGE

CIRCUIT WITH OPTIONAL HEATER

BRADENTON & PROVINCETOWN

AIR BATH CIRCUIT

BRADENTON & PROVINCETOWN WHIRLPOOL

WITH INSTALLED AIR SWITCH

POWER SPEED WAVE

www.mirabelleproducts.com

7

Framing and Installation

Structural measurements should be veried against the actual bath received to ensure proper t.

• Never lift the tub by the plumbing. Doing so can result in leaks.

• Check if the oor is level and of good quality. An uneven oor may impede proper installation of the tub.

• Clean installation area of any debris or trash.

Locate studs as needed. Ensure roughing-in dimensions are proper, plumb and square. Provisions must be made in all installations for an

access opening for servicing the pump and controls on the pump or blower side.

An access opening of at least 18’’ x 24’’ must be provided or warranty service will not be performed. It is strongly recommended that an

additional opening be provided for access to the drain components. The apron should not be used as the primary access opening.

If the suboor is not level, you must level the entire surface prior to installing the bathtub.

Ensure that the entire oor is level and can support a load of 80lbs. per square foot.

The bathtub must remain level in order for it to drain properly and must make contact with the leveling material.

1. Position the tub into the installation opening and level the deck in both directions, shimming the base of the tub if necessary. Mark the nal

position of the underside of the deck by tracing a line on to the studs (see Figure 1).

2. Remove the tub and attach a 1 x 4 stringer to the studs, with the top of the stringer touching the traced line. Never support the tub by its

deck lip or stringers (see gure 2).

3. Install drain components to the tub following the drain installation instructions. Note that this requires a cutout in the oor. Before replacing

your tub for nal installation, bathtubs require a 6’’ x 12’’ oor opening for the 1-1/2” drain and waste & overow kit. The drain/overow of

the bath extends below the bottom of the bath.

The bath must be supported along its entire bottom. Do not remove foam base & pad from the bottom of the tub. Use 1-1/2’’ to 2’’ of mortar

as bedding material (do not use sand or foam). After the mortar has been poured, and before it sets, position tub within recess until the rim is

leveled against the leveling stringers (see below).

FIGURE 1

STRINGER INSTALLATION

TYPICAL DROP-IN TYPE INSTALLATION

REFERENCE FOR DROP-IN INSTALLATION

FIGURE 2

TYPICAL ALCOVE INSTALLATION

18"

(457.2mm)

24"

(609.6mm)

24"

(609.6mm)

LEVELING

STRINGERS

ACCESS PANEL MUST BE LOCAT ED

ON THE SAME SIDE AS THE MOTOR.

ALLOW OPEN FRAMING ON

PUMP MOTOR END FOR SERVICE.

ACCESS PANELS NOT REQUIRED

FOR NON-SYSTEM TUBS.

NOTE:

FRONT EDGE OF BATH

MUST BE SUPPORTED

BY STUD WALL.

HEIGHT

TO LIP

TILE

WALLBOARD

G

CUTOUT

18"

(457.2MM)

AS DESIRED

MOUNTING

SURFACE

WATERPROOF

SEALANT

BATH

AS DESIRED

F

CUTOUT

C

SILICONE

1" X 4" JOIST

STUD

AIR GAP 1/4" OR MORE

UNLESS AS ACCESS OPENING OF AT LEST 18" X 24"

IS PROVIDED, WARRANTY SERVICE WILL NOT BE PERFORMED.

ACCESS PANEL MUST BE LOCAT ED

ON THE SAME SIDE AS THE MOTOR.

ALLOW OPEN FRAMING ON

PUMP MOTOR END FOR SERVICE.

ACCESS PANELS NOT REQUIRED

FOR NON-SYSTEM TUBS.

UNLESS AS ACCESS OPENING OF AT LEST 18" X 24"

IS PROVIDED, WARRANTY SERVICE WILL NOT BE PERFORMED.

E

C

D

W

www.mirabelleproducts.com

8

Allow the mortar material to completely harden before applying weight to the rim or bottom of the bath. Any nish material such as tile or

wall board must be self supporting if it contacts the deck of the bath.

Verify that the product is lever by checking the tub deck surface in all directions.

For system tubs ensure blower and or pump cords are properly plugged into the dedicated 120V/20A GFCI outlet to supply electrical power

to the system (Please reference pg. 6) for electrical requirement information. To test run the bath, ll the tub with water at least 3” above the

highest jet and operate the bath for 5 minutes. Check all bath and piping connections for leaks.

POST INSTALLATION CLEAN-UP

Remove all construction debris from bath. Do not use wire brushes or any other metal implement on bath surface.

Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent.

Stubborn dirt or stains may be removed using granular Spic and Span® mixed with water. Painter’s Naphtha can be used to remove excess

adhesives and/or wet oil-base paint.

Reference for correct tile ange installation

Use drawing below as a reference guide for rough-in measurements

DRAIN CLEARANCE

11”

12”

PUMP ACCESS

STUD

SUGGESTED WHIRLPOOL/BATH

INSTALLATION METHOD

WATERPROOF DRYWALL

OR CEMENT BOARD

TILE

ROOFING NAIL

SEALANT

TUB

1 X 4 (25mm X 76mm)

WOOD STINGER FULL LENGTH

FIGURE 1

STRINGER INSTALLATION

TYPICAL DROP-IN TYPE INSTALLATION

REFERENCE FOR DROP-IN INSTALLATION

FIGURE 2

TYPICAL ALCOVE INSTALLATION

18"

(457.2mm)

24"

(609.6mm)

24"

(609.6mm)

LEVELING

STRINGERS

ACCESS PANEL MUST BE LOCATED

ON THE SAME SIDE AS THE MOTOR.

ALLOW OPEN FRAMING ON

PUMP MOTOR END FOR SERVICE.

ACCESS PANELS NOT REQUIRED

FOR NON-SYSTEM TUBS.

NOTE:

FRONT EDGE OF BATH

MUST BE SUPPORTED

BY STUD WALL.

HEIGHT

TO LIP

TILE

WALLBOARD

G

CUTOUT

18"

(457.2MM)

AS DESIRED

MOUNTING

SURFACE

WATERPROOF

SEALANT

BATH

AS DESIRED

F

CUTOUT

C

SILICONE

1" X 4" JOIST

STUD

AIR GAP 1/4" OR MORE

UNLESS AS ACCESS OPENING OF AT LEST 18" X 24"

IS PROVIDED, WARRANTY SERVICE WILL NOT BE PERFORMED.

ACCESS PANEL MUST BE LOCATED

ON THE SAME SIDE AS THE MOTOR.

ALLOW OPEN FRAMING ON

PUMP MOTOR END FOR SERVICE.

ACCESS PANELS NOT REQUIRED

FOR NON-SYSTEM TUBS.

UNLESS AS ACCESS OPENING OF AT LEST 18" X 24"

IS PROVIDED, WARRANTY SERVICE WILL NOT BE PERFORMED.

E

C

D

W

Framing and Installation

www.mirabelleproducts.com

9

Series Soaker Air Whirlpool Total Massage L W D H A B

Bradenton MIRBDS6030 (L/R) NA NA NA 59.75" 30" 18.88" 17.88" 11" 12"

Bradenton MIRBDS6032 MIRBDA6032 MIRBDW6032 MIRBDT6032 60" 32" 20" 18.5" 11" 16"

Bradenton MIRBDS6032 (L/R) MIRBDA6032 (L/R) MIRBDW6032 (L/R) MIRBDT6032 L/R) 59.75” 32" 21" 20" 11" 16"

Boca Raton MIRBRS6640V MIRBRA6640V MIRBRW6640V MIRBRS6640V 66" 40" 22" 20.5" 35.75" 10"

Boca Raton MIRBRS7242V MIRBRA7242V MIRBRW7242V MIRBRS7242V 71.5" 42" 22" 20.5" 35.75" 10"

Sitka MIRSKS6030 (L/R) MIRSKA6030 (L/R) MIRSKW6030 (L/R) NA 60" 30" 19.5" 19.25" 8.75" 15"

Sitka MIRSKS6032 (L/R) MIRSKA6032 (L/R) MIRSKW6032 (L/R) NA 60" 32" 19.5" 19.25" 8.75" 16"

Sitka MIRSKS6032 MIRSKA6032 MIRSKW6032 NA 60" 32" 19.5" 18.5" 8.75" 16"

Sitka MIRSKS6036 MIRSKA6036 MIRSKW6036 MIRSKT6036 60" 36" 23" 22" 8.75" 18

Sitka MIRSKS6636 MIRSKA6636 MIRSKW6636 MIRSKT6636 66" 36" 23" 22" 8.75" 18""

Sitka MIRSKS7236 MIRSKA7236 MIRSKW7236 MIRSKT7236 72" 36" 23" 22" 8.75" 18"

Galatia MIRGAS6042 MIRGAA6042 MIRGAW6042 MIRGAT6042 60" 42" 21" 19.5" 10.25" 21"

Galatia MIRGAS7242 MIRGAA7242 MIRGAW7242 MIRGAT7242 72" 42" 21" 19.5" 10.25" 21"

Key West MIRKWS6036 MIRKWA6036 MIRKWW6036 MIRKWT6036 60" 36" 22" 20.5" 9.5" 18"

Key West MIRKWS7236 MIRKWS7236 MIRKWW7236 MIRKWT7236 72" 36" 22" 20.5" 8.25" 18"

Provincetown MIRPRS6032 (L/R) MIRPRA6032 (L/R) MIRPRW6032 (L/R) MIRPRT6032 (L/R) 60" 32" 21" 20" 9" 16"

Provincetown MIRPRS6032 MIRPRA6032 MIRPRW6032 MIRPRT6032 59.75” 32" 20" 18.5" 9" 16"

St. Augustine MIRSAS6042 MIRSAA6042 MIRSAW6042 MIRSAT6042 60" 42" 22" 20.5" 8.75" 30"

St. Augustine MIRSAS7242 MIRSAA7242 MIRSAW7242 MIRSAT7242 70" 42" 22" 20.5" 8.5" 36"

Rough-in Dimensions

www.mirabelleproducts.com

10

Deck-to-oor dimensions are measured through the drain hole to give a more consistent measurement. The dimensions are achieved by

laying a straight edge across the deck; the distance was then measured from the oor at the drain opening to the bottom of the straight

edge. (See illustration below). The lip height is then subtracted to give a more consistent oor to lip height. There may be height dimension

variations of plus minus ¼” from the stated dimension in the table, which is a standard production tolerance. Leave adequate clearance with

framing for side mounted controls.

Use drawing below as a guide for rough-in measurements

Height

to Top

Height

to Deck

Tape Measure

Straightedge or Wood Board

Floor

Measure from

Straightedge to Floor

Through Drain

MEASURE FROM THE

FLOOR TO THE STRAIGHT

EDGE THROUGH THE

DRAIN HOLE TO OBTAIN

A CONSISTENT HEIGHT

TO DECK DIMENSION.

D

B

L

W

A

H

L

B

A

W

C

W

B

D

B

L

W

A

H

L

B

A

W

C

W

B

D

B

L

W

A

H

L

B

A

W

C

W

B

D

B

L

W

A

H

L

B

A

W

C

W

B

www.mirabelleproducts.com

11

Care and Cleaning

The use of bath oils and bath salts is not recommended due to the difculty in cleaning the systems and doing so will void the consumer's

warranty.

Air and Total Massage Baths are equipped with an Automatic Purge Cycle for the air blower only. The air blower has a pre-programmed

purge cycle built in to expel the remaining water in the air channels. It activates within 20 minutes after the Air Bath is turned off and then

blows for about 2 to 3 minutes.

After the cycle is completed it will shut off automatically. There is nothing to be alarmed about if you hear a blowing noise coming from

the tub after the tub has been turned off. The noise you hear is the cleaning cycle in operation. It is recommended to activate the air bath

routinely to purge water from the air channel when tub is used as a soaker or shower only. Purge cycle is only activated when blower has

been used.

Pump and pipe circulation system should be ushed before rst use and on a monthly basis when product is under normal use.

Below are the recommended procedures for cleaning:

DO NOT use powdered cleaners unless cleaner is fully dissolved in water.

DO NOT RUN WHIRLPOOL DRY. Fill the tub with hot water 2-3 inches above the jets and add 2-3 teaspoons of low foaming detergent

such as dish washing machine detergent.

DO NOT use full strength bleach of ammonia cleaning solutions. Chemically active cleaning solution can damage the bath surface.

• Switch on whirlpool and run for 10 minutes.

• Drain tub completely.

• Fill tub with cold water above jets.

• Switch on whirlpool and run for 5 minutes.

• Drain tub completely.

DO NOT USE ABRASIVE CLEANERS as they will scratch and dull the surface of the acrylic and void the consumer warranty. Plaster can

be removed using a sharpened wooden stick.

DO NOT USE METAL SCRAPERS, WIRE BRUSHES OR OTHER HARSH ABRASIVE TOOLS.

Usually a mild detergent will remove construction debris. More stubborn debris may be removed with denatured alcohol, or Clorox Soft

Scrub® cleaner. Light scratches and dulled areas may be restored to original luster by rubbing with an automotive type cleaning compound

such as DuPont White Polishing Compound®.

Note: To restore dull or scratched units: Apply white automotive polishing with a clean rage. Rub scratches and dull areas vigorously. Wipe off

residue. Follow with a coat of white automotive paste wax.

DO NOT wax areas where you walk or stand. For crack and major surface damage, call customer service at 1-800-221-3379 for repair

recommendations.

Operating Instructions

1. Fill the bath to at least 3 inches above the jets before activating the pump. DO NOT turn on whirlpool unless jets are completely

submersed in water.

2. The air bath blower and/or whirlpool pump is activated by pushing the control panel buttons (Provincetown and Bradenton system tubs

air/whirlpool is turned on by depressing the actuator button) . DO NOT repeatedly depress the switch in rapid order if you do not see

the whirlpool function right away, as it may take a few seconds before you can see it fully operating. Please see air bath control or Total

Massage Control instructions on the following page for operation and features.

3. If any factory installed ttings are removed; do not operate the unit. A safety hazard may occur.

4. Do not use bubble bath when you operate the whirlpool pump. This might cause excessive foaming.

5. Bath oils should not be used when you operate the whirlpool. If used while soaking, please drain and clean the tub thoroughly prior to

activating the whirlpool system.

6. The use of bath salts is not recommended and doing so will VOID THE CONSUMER’S WARRANTY.

7. Both air and whirlpool systems are plumbed in a way that water will drain from the plumbing easily.

8. The air system is designed to purge within 20 minutes after use (see details on previous page).

9. There are no user serviceable parts located under the tub. If a problem develops, call 1-800-221-3379

www.mirabelleproducts.com

12

Jet Operation and Adjustment

The jets can be easily adjusted by pointing the jet-nozzle in the

desired direction. The strength of the water ow and air induction

can be regulated through twisting the jet- nozzle. Twisting the

nozzle counter-clockwise will decrease the water ow of that

particular jet. If the nozzle is twisted clockwise then the water ow

will increase up to its maximum ow. Only a 1/4 turn or 90° turn is

required from the lowest ow position to the fully OPEN position.

The jets can be easily adjusted by pointing the jet-nozzle in the

desired direction. The strength of the water ow and air induction

can be regulated through twisting the jet- nozzle. Twisting the

nozzle clockwise will decrease the water ow of that particular jet

If the nozzle is twisted counter-clockwise then the water ow will

increase up to its maximum ow. Only a 1/4 turn or 90° turn is

required from the lowest ow position to the fully OPEN position.

Mirabelle Boca Raton, Bradenton, Galatia, Key West,

Provincetown and St. Augustine jets

Mirabelle Sitka jets

The whirlpool is controlled by a three button control.

1. The rst button switches the water-pump on or off. The other features will not operate unless the pump is turned on.

2. The second button sets the power level of the pump. Holding the button depressed will cycle the pump power from low to high in a

continuous cycle. When the desired level is reached, remove your nger quickly from the button to maintain that power setting.

3. The third button is a three step wave action button. Once activated, the jets expel water in a slow pulsating ow called wave action.

There are 3 levels for wave strength.

a. Level 1: operates the pump at

a steady ow.

b. Level 2: quick wave action.

c. Level 3: slower wave action.

Whirlpool Control Center Features

Whirlpool

POWER SPEED WAVE

www.mirabelleproducts.com

13

The air bath is controlled by a three button control.

1. The rst button switches the blower on or off. The other features will not operate unless the blower is turned on.

2. The second button sets the power level of the blower. Holding the button depressed will cycle the blower power from low to high in a

continuous cycle. When the desired level is reached, remove your nger quickly from the button to maintain that power setting.

3. The third button is a three step wave action button. Once activated, the air holes expel air in a slow pulsating ow called wave action. There

are 3 levels for wave strength.

a. Level 1: operates the blower at a steady ow.

b. Level 2: quick wave action.

c. Level 3: slower wave action.

Air Bath Control Center Features

Air

POWER SPEED WAVE

Total Massage units are a combination of whirlpool and air massages. The left three buttons on the control panel. Operate the whirlpool

and the right three buttons operate the air system. The whirlpool and air massage systems may be used at the same time if desired. The

whirlpool and air bath operations are explained in section above.

Total Massage Control Center Features

Total Massage

AIR JETSPEED SPEEDWAVE WAVE

In-Line heater operation

If your unit has an in-line heater installed, operation is automatic only during the use of the whirlpool function. The in-line heater will maintain

the water temperature only while the whirlpool is in operation.

Operating Instructions for Provincetown and Bradenton

Whirlpool baths: Equipped with on/off air switch actuator. Each depression of the switch will activate the pump. If off, one depression will turn

the pump on. if on, the next depression will turn it off.

Air baths: Equipped with a three-speed air switch actuator. Each depression of the switch will change the ow of air. The forth depression will

turn off the air pump.

Total massage baths: Equipped with both an on/off air switch actuator for whirlpool function and three-speed air switch actuator for air

function. See above for operation details.

www.mirabelleproducts.com

14

PROBLEM CAUSES SOLUTION

Motor will not start - Circuit breaker may be tripped

- Lose/Bad wire connection

- GFCI is tripped

- Incorrect electrical installation

- Jets are closed

- Make sure it is a 20 Amp circuit breaker with nothing else tied to the circuit

- Check for incorrect or lose wire connections, and pump/heater has been

properly grounded

- Reset if necessary

- Insure each motor/ in-line heater uses its own 20 Amp circuit breaker and GFCI

plug

- Make sure that jets are fully operational and water is owing

Motor overheating and

cycling

on and off

- Lose/Bad wire connection

- Incorrect Amp usage

- Air supply to motor

- Check for incorrect or loose wire connections

- Check for low voltage supply

- Make sure motor gets fresh air supply and vents are not clogged

Pump/motor operates

but jets/ air is not fully

function

- Jets are closed

- Suction/ strainer may be clogged

- Air valves are closed

- Open jets fully

- With pump off, remove the suction cover/ strainer and

remove any debris.

- Open all air control valves

Motor makes humming

noise but won’t start

- Jets are closed

- Pump does not have space

to operate

- Debris in pump

- Incorrect Amp usage

- Make sure jets are fully open

- Make sure the motor shaft turns free

- Check for jammed impeller or an obstruction on the

(volute) casing.

- Check for low voltage and undersized wire

Low water ow - Clogged pipe

- Incorrect electrical installation

- Check for clogged plumbing lines

- Check for low voltage

Water leaks - Leak in the plumbing - Check compression ttings (union connections) making sure

they are properly aligned and secured. Hand tighten only.

Do not use any tools.

- Make sure the o-ring is properly seated and not damaged.

Troubleshooting

FIVE-YEAR LIMITED WARRANTY

All Mirabelle Whirlpools and Bathing Systems are warranted in accordance with the following Limited Warranty: Mirabelle Whirlpools and Bathing Systems

are warranted against defects in material and workmanship for a period of ve (5) years from the date of the rst consumer purchase. This Warranty shall

apply to defective acrylic surfaces which crack, fade or blister, and any defect in whirlpool and bathing system components. The Warranty extends to the rst

consumer purchaser and not to subsequent owners, transferees or users other than the rst purchaser. This warranty does not extend to products previously

utilized as display models. This Warranty shall apply to products installed and used only for personal, family or household purposes and which are installed

and maintained in accordance with Mirabelle Whirlpool and Bathing Systems’ recommended installation and maintenance procedures. This Warranty does

not extend to defects or damage caused, in whole or in part, by any unauthorized or unreasonable use. No liability shall exist for incidental or consequential

damages caused in whole or part by any defects in Mirabelle Whirlpools and Bathing Systems. No warranty, expressed or implied, including any warranty of

merchantability or tness for a particular purpose, shall apply after the warranty period described above.

Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts. The above

limitation may not apply to you.

In the event of a defect in material or workmanship of a Mirabelle Whirlpool or Bathing System during the Warranty period, defective products will be

repaired or replaced as Mirabelle, at its sole and absolute discretion, determines. However, Mirabelle shall not be liable for the expense for removing

defective products or installing replacement products. In certain circumstances, some states do not allow the limitation of liability for removal, transportation

and reinstallation expenses. The above limitation may not apply to you.

Only Mirabelle is authorized to perform its warranty obligation. If you wish to obtain performance of the Mirabelle warranty obligation you should contact

Mirabelle, at (800) 221-3379. Other information about performance of the Mirabelle Whirlpool and Bathing Systems’ warranty obligation may be obtained at

the same address and telephone number. This Warranty gives you specic legal rights and you may also have other rights which vary from state to state.

www.mirabelleproducts.com

15

Cut-Out Templates

INSTALLING AN OVAL TUB WITH A TEMPLATE

The back section of the installation manual contains oval cut out instructions. Use pencil and tape measure to plot the coordinates and draw

the cut out. Take special care to place tub carefully in the platform cutout, because the tub might break and the ensuing warranty limitations

would become void. For additional questions on installing your tub read “installation procedures” above or call customer service at 800-221-

3379.

Cutout for Galatia Tubs

DROP-IN

CUT OUT LINE

UNDERMOUNT

CUT OUT LINE

6042 GALATIA TEMPLATE

58.2

54.753

36.891

40.2

DROP-IN

CUT OUT LINE

UNDERMOUNT

CUT OUT LINE

7242 GALATIA TEMPLATE

70

66.729

36.885

39.999

30

39.5

19.75

69.5

R19.75

25

37.5

18.75

63.5

R18.75

DROP-IN

CUT OUT LINE

UNDERMOUNT

CUT OUT LINE

6042 GALATIA TEMPLATE

58.2

54.753

36.891

40.2

DROP-IN

CUT OUT LINE

UNDERMOUNT

CUT OUT LINE

7242 GALATIA TEMPLATE

70

66.729

36.885

39.999

30

39.5

19.75

69.5

R19.75

25

37.5

18.75

63.5

R18.75

Mirabelle Cut-Out Template

Use for Boca Raton 7242

Mirabelle Cut-Out Template

Use for Boca Raton 6640

DROP-IN

CUT OUT LINE

UNDERMOUNT

CUT OUT LINE

6042 GALATIA TEMPLATE

58.2

54.753

36.891

40.2

DROP-IN

CUT OUT LINE

UNDERMOUNT

CUT OUT LINE

7242 GALATIA TEMPLATE

70

66.729

36.885

39.999

30

39.5

19.75

69.5

R19.75

25

37.5

18.75

63.5

R18.75

DROP-IN

CUT OUT LINE

UNDERMOUNT

CUT OUT LINE

6042 GALATIA TEMPLATE

58.2

54.753

36.891

40.2

DROP-IN

CUT OUT LINE

UNDERMOUNT

CUT OUT LINE

7242 GALATIA TEMPLATE

70

66.729

36.885

39.999

30

39.5

19.75

69.5

R19.75

25

37.5

18.75

63.5

R18.75

www.mirabelleproducts.com

05/16 165789

Page is loading ...

www.mirabelleproducts.com

6

Exigences et renseignements électriques

TOTAL MASSAGE CIRCUIT WITH OPTIONAL HEATER

PUMP FLOW

CONTROLL VALV E

0.5 AMP

BACK OF 6 BTN CONTROL

PIGGY BLOWER

9.5 AMP

TMS - VARIABLE

CONTROL

TMS-P/TIMER

CONTROL

ON / OFF PUMP

9 AMP

OPTIONAL

120V, 60 HZ

20 AMP GFCI

120V / 20AMP

MALE PLUG

GFCI GFCI

ELECTRICAL

FEED

120V, 60 HZ

20 AMP GFCI

HEATER

AIR SPEED WAVE

SPEEDJETS WAVE

WHIRLPOOL CIRCUIT WITH OPTIONAL HEATER

PUMP FLOW

CONTROLL VALV E

0.5 AMP

TMS-P/TIMER

CONTROL

ON / OFF PUMP

9 AMP

OPTIONAL

HEATER

120V, 60 HZ

20 AMP GFCI

120V / 20AMP

MALE PLUG

GFCI GFCI

ELECTRICAL

FEED

120V, 60 HZ

20 AMP GFCI

BACK OF 3 BUTTON CONTROL

AIR MASSAGE CIRCUIT

PIGGY BLOWER

9.25 AMP

TMS - VARIABLE

CONTROL

120V, 60 HZ

20 AMP GFCI

GFCI GFCI

ELECTRICAL

FEED

120V, 60 HZ

20 AMP GFCI

GFCI GFCI

ELECTRICAL

FEED

BACK OF 3 BUTTON CONTROL

120V, 60 HZ

20 AMP GFCI

GFCI GFCI

ELECTRICAL

FEED

120V, 60 HZ

9.25 AMP

HEATER

PIGGY BLOWER

9.5 AMP

AIR SWITCH

ON / OFF PUMP

9 AMP

AIR SWITCH

CONTROL BOX

PIGGY BLOWER

9.5 AMP

PUMP / MOTOR

120V, 60 HZ

20 AMP GFCI

GFCI GFCI

ELECTRICAL

FEED

AIR SWITCH

BRADENTON & PROVINCETOWN TOTAL MASSAGE

CIRCUIT WITH OPTIONAL HEATER

BRADENTON & PROVINCETOWN

AIR BATH CIRCUIT

BRADENTON & PROVINCETOWN WHIRLPOOL

WITH INSTALLED AIR SWITCH

POWER SPEED WAVE

Page is loading ...

www.mirabelleproducts.com

8

Laissez le mortier durcir complètement avant d’appliquer toute pression sur les bords ou sur le fond de la baignoire. Tout matériau de nition,

comme des carrelages ou des panneaux muraux, doit être xé indépendamment de la baignoire s’il est en contact avec cette dernière.

Vériez que la baignoire est à l’horizontale en vériant le niveau de la surface de la baignoire dans toutes les directions.

Si vous installez une baignoire avec un système à remous, vériez que les cordons de la soufante et de la pompe sont correctement

branchés sur la prise courant 120 V / 20 A protégée par un disjoncteur DDFT dédiée à l’alimentation électrique du système (Reportez-vous

à la page 6) pour les exigences et renseignements électriques. Pour effectuer un test de la baignoire, remplissez la baignoire avec de l’eau

au moins 8 cm (3 po) au-dessus du plus haut jet et actionnez le bain pendant 5 minutes. Inspectez tous les raccords de la baignoire et de la

tuyauterie pour vérier l’absence de fuites.

NETTOYAGE APRÈS INSTALLATION

Nettoyez tous les débris de construction de la baignoire. N’utilisez pas une brosse métallique ou tout autre objet en métal sur la surface de la

baignoire.

Le nettoyage après installation peut généralement se faire en utilisant de l’eau chaude et du détergent liquide pour lave-vaisselle.

Il est possible de faire partir les taches tenaces en utilisant de la poudre Spic and Span® mélangée avec de l’eau. Il est possible d’utiliser du

naphte de pétrole pour nettoyer les traces d’adhésifs ou les taches de peinture à l’huile.

Reference for correct tile ange installation

Use drawing below as a reference guide for rough-in measurements

DRAIN CLEARANCE

11”

12”

PUMP ACCESS

STUD

SUGGESTED WHIRLPOOL/BATH

INSTALLATION METHOD

WATERPROOF DRYWALL

OR CEMENT BOARD

TILE

ROOFING NAIL

SEALANT

TUB

1 X 4 (25mm X 76mm)

WOOD STINGER FULL LENGTH

FIGURE 1

STRINGER INSTALLATION

TYPICAL DROP-IN TYPE INSTALLATION

REFERENCE FOR DROP-IN INSTALLATION

FIGURE 2

TYPICAL ALCOVE INSTALLATION

LEVELING

STRINGERS

ACCESS PANEL MUST BE LOCATED

ON THE SAME SIDE AS THE MOTOR.

ALLOW OPEN FRAMING ON

PUMP MOTOR END FOR SERVICE.

ACCESS PANELS NOT REQUIRED

FOR NON-SYSTEM TUBS.

NOTE:

FRONT EDGE OF BATH

MUST BE SUPPORTED

BY STUD WALL.

HEIGHT

TO LIP

TILE

WALLBOARD

G

CUTOUT

18”

(457.2MM)

24”

(609.6MM)

18”

(457.2MM)

24”

(609.6MM)

AS DESIRED

MOUNTING

SURFACE

WATERPROOF

SEALANT

BATH

AS DESIRED

F

CUTOUT

C

SILICONE

1” X 4” JOIST

STUD

AIR GAP 1/4” OR MORE

UNLESS AS ACCESS OPENING OF AT LEST 18” X 24”

IS PROVIDED, WARRANTY SERVICE WILL NOT BE PERFORMED.

ACCESS PANEL MUST BE LOCATED

ON THE SAME SIDE AS THE MOTOR.

ALLOW OPEN FRAMING ON

PUMP MOTOR END FOR SERVICE.

ACCESS PANELS NOT REQUIRED

FOR NON-SYSTEM TUBS.

UNLESS AS ACCESS OPENING OF AT LEST 18” X 24”

IS PROVIDED, WARRANTY SERVICE WILL NOT BE PERFORMED.

E

C

D

W

Support et installation

Page is loading ...

www.mirabelleproducts.com

10

Les dimensions entre la surface et le plancher sont mesurées par l’orice de vidange, an d’obtenir une mesure plus cohérente. Les

dimensions ont été obtenues en plaçant une règle droite en travers de la surface de la baignoire et en mesurant la distance entre le plancher

et le bord inférieur de la règle droite, à travers l’orice de vidange. (Voir l’illustration). La hauteur du rebord est ensuite soustraite an de

fournir une hauteur plus cohérente entre le sol et la hauteur du rebord. Les dimensions de hauteur peuvent présenter des variations pouvant

atteindre +/- 6 mm (¼ po) par rapport aux dimensions indiquées dans le tableau, ce qui représente une tolérance de production standard.

Laissez un dégagement sufsant avec le support pour pouvoir installer les commandes à montage latéral.

Use drawing below as a guide for rough-in measurements

Height

to Top

Height

to Deck

Tape Measure

Straightedge or Wood Board

Floor

Measure from

Straightedge to Floor

Through Drain

MEASURE FROM THE

FLOOR TO THE STRAIGHT

EDGE THROUGH THE

DRAIN HOLE TO OBTAIN

A CONSISTENT HEIGHT

TO DECK DIMENSION.

D

B

L

W

A

H

L

B

A

W

C

W

B

D

B

L

W

A

H

L

B

A

W

C

W

B

D

B

L

W

A

H

L

B

A

W

C

W

B

D

B

L

W

A

H

L

B

A

W

C

W

B

Page is loading ...

www.mirabelleproducts.com

15

Modèles de découpe

INSTALLATION D’UNE BAIGNOIRE OVALE AVEC UN MODÈLE

La section au dos du manuel d’installation contient des instructions de découpe ovale. Utiliser un crayon et d’un ruban à mesurer pour

marquer les coordonnées et dessiner la forme de découpe. Prenez soin de placer soigneusement la baignoire dans la découpe de la

plateforme, parce que la baignoire pourrait se briser et les limitations de validité de la garantie pourraient s’appliquer. Pour toute question

concernant l’installation de votre baignoire, veuillez consulter la section « Procédures d’installation » ci-dessus ou appeler le service à la

clientèle au 800-221-3379.

Cutout for Galatia Tubs

DROP-IN

CUT OUT LINE

UNDERMOUNT

CUT OUT LINE

6042 GALATIA TEMPLATE

58.2

54.753

36.891

40.2

DROP-IN

CUT OUT LINE

UNDERMOUNT

CUT OUT LINE

7242 GALATIA TEMPLATE

70

66.729

36.885

39.999

30

39.5

19.75

69.5

R19.75

25

37.5

18.75

63.5

R18.75

DROP-IN

CUT OUT LINE

UNDERMOUNT

CUT OUT LINE

6042 GALATIA TEMPLATE

58.2

54.753

36.891

40.2

DROP-IN

CUT OUT LINE

UNDERMOUNT

CUT OUT LINE

7242 GALATIA TEMPLATE

70

66.729

36.885

39.999

30

39.5

19.75

69.5

R19.75

25

37.5

18.75

63.5

R18.75

Mirabelle Cut-Out Template

Use for Boca Raton 7242

Mirabelle Cut-Out Template

Use for Boca Raton 6640

DROP-IN

CUT OUT LINE

UNDERMOUNT

CUT OUT LINE

6042 GALATIA TEMPLATE

58.2

54.753

36.891

40.2

DROP-IN

CUT OUT LINE

UNDERMOUNT

CUT OUT LINE

7242 GALATIA TEMPLATE

70

66.729

36.885

39.999

30

39.5

19.75

69.5

R19.75

25

37.5

18.75

63.5

R18.75

DROP-IN

CUT OUT LINE

UNDERMOUNT

CUT OUT LINE

6042 GALATIA TEMPLATE

58.2

54.753

36.891

40.2

DROP-IN

CUT OUT LINE

UNDERMOUNT

CUT OUT LINE

7242 GALATIA TEMPLATE

70

66.729

36.885

39.999

30

39.5

19.75

69.5

R19.75

25

37.5

18.75

63.5

R18.75

Page is loading ...

Mirabelle A7242OMIRBS Installation guide

This manual is also suitable for

Mirabelle A7242OMIRBS Installation guide

in other languages

Related papers

Other documents