Wireless Controller for Wave Maker
User’s Manual
Matched Models, RW4/8/15/20 and WP10/25/40/60
Company：Jebao(Zhongshan)Electrical Appliance Co.Ltd
Address：Tongmao Industrial Park, Dongsheng Town, Zhongshan city.
Guangdong Pro. China
Tel.: +86-760-28136717/20/21 Fax: +86-760-28136725
Jebao wave makers are intended to simulate the natural waves and
whirlpools found in a marine environment.
Before installing and using the controller, please read through these
instructions to familiarise yourself with the correct operation of the device.
Features:
1. Unique wireless multi- mode controller to allow adjustment of the
wave maker to suit the users requirements.
2. Use of low-voltage, low power, DC variable-speed pump for safe
operation.
3. Easy adjustment & operation.
4. Wireless communication with other Wireless Controllers
Installation Instructions:
1. Accessories: Intelligent controller, power adaptor, mains cable, double
sided tape, instruction manual.
2. Assembly: Remove one side of the double-sided tape and stick to the
rear of the controller. Remove the other side of the double-sided tape and
affix the controller in a suitable location.
3. Attach the 3-pin waterproof connector from the pump to the controller.
Then attach the DC plug to the controller. And attach the AC cable of the
adaptor.
Fig 1: assembly and operation
Fig. 1
Fig.2
III. Operation and Function
Functions:
MODE/NIGHT: Press the “MODE” button to cycle through the
different modes. Long press to enter into Night mode.
SPEED/FEED: Press the button to adjust the pump flow rate. Long
press to enter/exit the 10 minute feed mode.
Wi-Le/ LOCK: Press the button to set controller to Master /Slave or
independent mode (slaves are syncronised with “master controller”).
Lock the setting by long press of the button.
DIAL: Rotate the dial to adjust different wave periods and patterns in
W1 mode. Adjusts the flow speed in W2 and ELSE mode. Adjusts the
on/off time in mode C.
MASTER Control：Press “Wi-Le” once and enter into Master mode-
“Master” indicator light will be lit.
Master controller mode will operate all the functions for controllers set
to slave mode. In Slave mode, all operations are disabled except
adjusting flow rate by rotating the dial.
With two or more wave makers, set one as the Master and the others
as Slave. You can achieve the same function and operation for all the
pumps by adjusting only the Master controller.
Introduction of each mode
W1：Wave Mode
Adjusting the dial will alter the pump on/off period. This will create
a wave in the tank which can be adjusted to suit your needs. Increase
the wave length by turning the dial clockwise, and reduce by turning
the dial anti clockwise.
Tip: You should change the dial gradually and observe the wave
pattern for a while after each adjustment. Press “SPEED/FEED” to
adjust the flow rate.
W2： Sine Mode
One or more pumps can operate at the same time in this mode. The
power various between 15%-100% in a sinusoidal fashion.
Else： Random Mode
One or more pumps can operate at the same time in this mode. The
power of pump is altered randomly.
H：Constant Flow Mode
One or more pumps can operate at the same time in this mode. Flow
rate can be adjusted by “SPEED/FEED” button.
C – Anti Sync mode.
Pump 1 & 2 operate alternately (Anti SYNC). P1 run, P2 stop--P1
stop, P2 run--P1 run -- P2 stop - the cycling is repeated. The flow
rate of P1 & P2 can be adjusted with P1_FLOW & P2_FLOW.
The interval dial will adjust the frequency of the alternating between
P1 & P2.
C： Anti Sync mode
Two pumps are needed to run in anti sync. Pump 1 & 2 operate
alternately (Anti SYNC). P1 run, P2 stop--P1 stop, P2 run--P1 run --
P2 stop - the cycling is repeated. The cycle period can be adjusted
with the dial (1s – 1min). The flow rate of P1 & P2 can be adjusted
rate by pressing SPEED/FEED.
Night Function:
Enter into Night Mode by a long press of MODE/NIGHT button until
yellow “NIGHT” indicator lights. Wavemakers function normally
during day and enter into NIGHT mode automatically when it’s dark
–wavemaker output will be reduced to 30% flow. Exit mode by a long
press of ”MODE/NIGHT” button until the yellow indicator goes out.
FEED Function:
Enter feed mode by a long press of “SPEED/FEED” button until the
blue indicator lights. The pump will stop working and allow fish to
feed for 10 minutes. Pump will revert back to normal mode after that.
Exit mode by a long press of ”FEED/SPEED” button until the 10 min
indicator goes out.
Dial Locking Function: Enter lock mode by a long press of the
Wi-Le/LOCK button until the red LOCK indicator lights. It prevents
the wave pattern and time from being altered – the dial has no effect
when the lock mode is on.
Warnings
The controller must not be subjected to any moisture – please position
the controller away from any area where it can be splashed with water.
If it is splashed, dry immediately with a soft cloth.
Do not disassemble the controller and the power adaptor.
This product is indoor use only.
Appendix: TYPICAL PUMP LOCATIONS
l
Ref.1
Ref.2
Ref.3
Ref.4
-
1
-
2
-
3
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Jecod RW-8 User manual
-
Sea Ray 2004 600 SUN SPORT Owner's manual
-
Uponor Smatrix Wave Owner's manual
-
-
Chrysler Caliber SRT4 User manual
-
Vortech MP10 Setup Manual
-
-
Culligan M2-5 Installation, Operation And Service Instructions
-
-
