Channel Plus 5435 User manual

Type
User manual
2005 CATALOG
“Innovations in video,voice and data”
Over two decades of excellence in video, voice, and data products.
For over 20 years, the ChannelPlus product line has been acknowledged as the premier brand in multi-room
audio/video distribution systems. Innovative design and dependable performance have made ChannelPlus the
number one choice of professional installers.
ChannelPlus products are used in residential homes and commercial installations such as restaurants,
sports bars, training facilities, and schools. Homeowners can enjoy an advanced integrated home network that
provides outstanding picture quality to every TV, clear telephone connections, easy satellite access, a residential
gateway for data networking, and the ability to watch a front door camera, DVD, and VCR from every TV in the
house. Why limit home theater to one room? With the addition of a ChannelPlus stereo modulator, homeowners
can distribute home theater all throughout the house.
ChannelPlus products include a complete line of modulators, cameras, enclosures, RF amplifiers, distribution
panels, and telephone products. And ChannelPlus is one of the many household technology brands of Linear LLC.
No strings attached 2/5/15 warranty.
Don’t worry about fine print on a ChannelPlus warranty. There is none. We do not require that the installation
be done by a certified installer (although we do recommend it). We do not void our warranty if other products
are used with ours in the same systems. We offer two years on audio amplifiers and data products, and five years
on active products* (such as amplifiers, modulators, and infrared receivers). On passive products, we offer a full
15 years* (passive products include rack mount accessories, filters, and splitters).
*All products in this literature are protected by one or more US and international patents, issued or pending.
All product brands mentioned in this catalog are trademarks or registered trademarks of their respective manufacturers.
ChannelPlus products delivered direct to you.
MTExpress
®
is our full-line ChannelPlus, Linear, and OpenHouse product distributor.
Mail order sales are available from 7 am to 4:30 pm Pacific Time weekdays:
By Phone: 888-996-4949
By Fax: 888-996-4950
Internet sales are available 24 hours a day.
www.mtx-sales.com
Telephone support for dealers and installers.
Call 800-999-5225 for toll-free,
US-based technical assistance 7 am to 4:30 pm Pacific Time every business day.
CONTENTS
INTRODUCTION
ChannelPlus and Structured Wiring 2
New Product Highlights 3
PRE-WIRE AND INTEGRATED SYSTEMS
Pre-Wire Cabling 4
Pre-Wire for Audio, Video, and Television 5
Pre-Wire for Telecommunications and Cameras 6
Pre-Wire for Data 7
S-VIDEO DISTRIBUTION
True 8x8 Audio/Video Matrix Switcher 8
Audio/Video Switcher 10
Video Distribution Over CAT-5 Cable 12
Video Distribution Panel 13
S-Video Modulators 14
STRUCTURED WIRE
Data and Telephone Distribution Modules 16
Ethernet Router and Switch 17
TAP (Total Access Port) Wall Plates 18
Rack Mount Accessories 19
RF-DISTRIBUTION
RF Distribution Amplifiers 20
Distribution Amplifiers 22
RF Amplifiers 24
MODULATION
Modulators 26
Modulator Starter Kits 28
All-In-One Video Distribution 30
IR ACCESSORIES
Infrared Accessories 32
MUSIC DISTRIBUTION
Multi-Source, Multi-Zone Music Distribution 34
CAMERAS
Black and White; Color Cameras 36
COMBINERS AND SPLITTERS
Splitters, Combiners, and Taps 38
ACCESSORIES
Accessories and Filters 40
REFERENCE GUIDES
Digital Television 41
RF Troubleshooting 42
RF System Design 43
Power Supply Chart 44
International Standards 45
Frequency Spectrum 46
Glossary of RF and Data Terms 47
INDEX 49
800.999.5225 • www.channelplus.com 1
2 800.999.5225 • www.channelplus.com
STRUCTURED WIRE FOR THE CUSTOM HOME
SVS-52
Five source A/V switcher
SVC-10
Delivers S-video and audio over CAT-5
to a remote location up to 1,000’ away
SVM-22
2-channel S-video stereo modulator
SVM-24
4-channel S-video stereo modulator
MDS-6A
Music distribution for six audio sources
to six rooms
DMT-24
Telephone distribution for four lines to 24
locations
DMT-16
Telephone distribution for four lines to
16 locations
DMD-16
16-port CAT-5e termination panel for data,
telephone, or A/V
DA-550HHR/BID
RF Distribution Amplifier to eight locations
DA-506BID
RF Distribution Amplifier to six locations
DA-8200HHR/BID
RF Distribution Amplifier to eight locations
H638
Ethernet Switch networks home computers,
printers, etc.
H634
Ethernet broadband residential gateway
routes data from DSL or cable modem
2619
10-space rack mount grid system
800.999.5225 • www.channelplus.com 3
Audio/Video Distribution
SVS-88
True 8x8 switching of S-video,
composite video, stereo audio, and
Dolby
®
digital audio, plus IR control.
See pages 10-11 for details
Music Distribution
MDS-6A; MCS-1A; MCS-2A
Multi-room, multi-source, 6x6 music
distribution system with 40 watts/
channel and keypad control.
See pages 34-35 for details
Modulation
5415; 5425; 5435; 5445
Economically priced, one, two, three,
and four channel mono modulators
with loop-through capabilities.
See pages 26-27 for details
Accessories
TAP (Total Access Port) Wall Plates
Self-mapping, easy-to-terminate wall
plates — dual data, data/telephone,
data/telephone/coax, and telephone/
coax models available in three colors.
See page 18 for details.
CHANNELPLUS
®
NEW PRODUCTS 2005
4 800.999.5225 • www.channelplus.com
The demand for multi-room video entertainment and telecommunications
(telephone, fax, computer, and data networking) is easily satisfied with the
installation of RG-6 coax and CAT-5 UTP wire. The key is to pre-wire. When you
put the right cables in the walls, the rest is easy.
An important feature of the ChannelPlus integrated home network is that it
utilizes industry-recognized cabling. The cable types listed here are available from
a wide variety of manufacturers ensuring both competitive prices, availability,
and compatibility now and in the future.
CABLE TYPES AND USAGE
RG-6
RF sources like CATV, off-air NTSC, and off-air ATSC (HDTV) use RG-6 coax with
standard foil shield and aluminum braid. For DBS satellite installations — from dish,
to multi-switch, to receiver — use standard RG-6. It is perfect for most residential
situations. In commercial or extreme noise environments (such as near a radio or
television transmitter tower), use quad-shielded RG-6.
CAT-5
Category 5 is recommended for telecommunication, camera, and data applications.
Consumers building a new home will often want to provide a computer network in
order to protect the long-term resale value of the home. Installing and terminating
the cable is as simple as a telephone installation. CAT-5 is made up of four
unshielded twisted pairs (UTP). This type of cable is easy to find and by changing
the termination jacks, you can upgrade the wiring for future applications such as
video distribution.
PRE-WIRE WITH INDUSTRY STANDARD CABLING
CAT-5 TELEPHONE PAIRS
CAT-5 CONNECTION TO
TOTAL ACCESS PORT WALL PLATE
CAT-5 DATA TERMINATION
800.999.5225 • www.channelplus.com 5
PRE-WIRE AUDIO/VIDEO AND TELEVISION WITH RG-6 COAX
PRE-WIRE GUIDE
Using RG-6 white and black coaxial
cable, install the following cable runs
from the network enclosure:
• One black coax from each TV
or computer location.
• One white coax from everywhere
one or more video sources might
be located.
• Video sources include VCRs, satel-
lite receivers, TiVo, DVD players,
cameras, computers, and Internet
TV products.
• One white coax from the CATV
demarcation point.
• One white coax to a place where
an off-air antenna might be located.
• Four white coax to a place where a
satellite dish with a dual LNB might
be mounted.
cable: coaxial cable type RG-6 75
connectors: type F
applications: CATV, antenna,
audio/video, and satellite.
COLOR CODING
white RG-6 coax: use as a “send”
or “upstream” cable from modulators
to distribution panel
black RG-6 coax: use as “receive”
or “downstream” cable from
distribution panel to TVs
6 800.999.5225 • www.channelplus.com
PRE-WIRE TELEPHONE, MULTI-ROOM AUDIO,
AND SECURITY CAMERAS with CAT-5 or CAT-5e
PRE-WIRE GUIDE
Using gray or white Category 5 or
Category 5e cable, install the
following cable runs from the net-
work enclosure:
One from each telephone location.
• One from the location(s) where
a satellite receiver might be located.
• One from each video camera
location (front door, back door,
baby’s room, backyard).
One from the telephone company’s
demarcation point.
• One from the front door for
installing an intercom.
• Two from the media center for video
and audio distribution and control.
cable: Category 5 or Category 5e
connectors: jacks and plugs type
RJ-11 (1 pair), type RJ-14 (2 pair),
and type RJ-25 (3 pair)
applications: telephone, fax, com-
puter modem, and video cameras
COLOR CODING
gray or white: telephone
yellow: demarc and gateway
800.999.5225 • www.channelplus.com 7
PRE-WIRE DATA NETWORKING AND INTERNET
with CAT-5e
PRE-WIRE GUIDE
Using Category 5e cable, install the
following cable runs from the net-
work enclosure:
• One from each computer location.
• One from any location(s) where a
computer peripheral (such as a
printer) might be located separately
from the computer.
• One at any location where access
to the network is desired (kitchen,
bedroom, or den).
cable: Category 5e
connectors: jacks and plugs are
Category 5e, type RJ-45 (4 pair)
applications: printer sharing, 10
BASE-T (Ethernet) or 100 BASE-T
(Fast Ethernet)
COLOR CODING
blue: data
8 800.999.5225 • www.channelplus.com
VIDEO DISTRIBUTION
TRUE 8x8 AUDIO/VIDEO MATRIX SWITCHER
Our SVS-88 is an industry leader in solid 8x8 switching with volume control,
S-video, stereo, or digital audio options, plus IR control. Up to 8 S-video
(or composite video with an external adapter) sources can be switched using the
SVS-88. Composite is up converted to S-video. DVRs, VCRs, DVD players, cable
boxes, and satellite receivers, including digital audio, can be converted to CAT-5
and transmitted up to 1,000 feet by adding our SVC-10 to the system. Inputs can
be switched at the remote locations using an IR remote. IR is passed back down
the same CAT-5 cabling from the remote location.
When multiple locations are needed, our
SVD-8 can expand the output to eight different
locations up to 1,000 feet away. For more
locations, additional SVD-8s can be added.
SVS-88 FEATURES
• Audio/video matrix switcher
• Any eight A/V inputs switched to any eight
A/V outputs
• All video connections are S-video type (composite video can be used with an
external adapter)
• Stereo audio analog and digital inputs and outputs
• Linear or logarithmic volume control for each output
• Simple text based commands for PC control
• Compatible with Crestron
®
, Elan
, AMX
®
and other home control systems
• RS-232 and RS-485 interface
• Switches PAL, SECAM, NTSC
• Front panel controls with pushbuttons and 7-segment displays
• IR control with built-in command set
• Set-top or rack mount
• International power supply
SUGGESTED USES
• Home theaters, whole-house video systems, sports bars, stadiums, casinos,
schools
• Any place that needs quality video to multiple locations up to 2,000 feet using
SVC-10, SVD-8, and SVC-10R components
model SVS-88
NEW!
800.999.5225 • www.channelplus.com 9
SPECIFICATIONS SVS-88
ELECTRICAL Input Voltage Range 100-240 VAC 50/60 Hz
Power Consumption 65 Watts maximum
Nominal Audio/Video Input/Output Levels 1 volt peak-to-peak
Audio/Video Shutdown Levels 3 volts peak-to-peak
CONNECTOR TYPES Video S-video (16)
Stereo Audio RCA (32)
Digital Audio RCA (16)
RS-232 9-pin sub-D (1)
RS-485 Expansion Ports RJ-12 (2)
Direct IR Input 3.5 mm jack (1)
Power Cord Connector EIC-320 (1)
MECHANICAL Dimensions 16-3/4” W x 3-1/2” H x 13-3/4”
Weight 16 lbs. (18 lbs. boxed)
Connection Diagram for SVS-88, SVC-10, SVD-8
10 800.999.5225 • www.channelplus.com
VIDEO DISTRIBUTION
5-SOURCE VIDEO/AUDIO SWITCHER
The SVS-52 video/audio switcher allows users to choose between five video/audio
sources. This versatile product operates as a stand-alone or expansion video/audio
switcher for home theater and music systems. Combine the SVS-52 with the SVC-10
and have multi-source selection capabilities up to 1,000 feet away. The SVS-52 can be
used in RS-232 based multi-unit installation systems like Crestron
®
, Elan
, and AMX
®
.
FEATURES:
• Five S-video/composite video and analog/digital audio inputs
• Five S-video/composite video and analog/digital audio outputs
• Composite to S-video conversion on all video inputs
• Cross conversion of optical and coax digital inputs
• IR and RS-232 control interfaces
• Front panel convenience inputs
• Remote control included
• Direct source selection
• IR learning capabilities
• Broadcast quality switching
• Auto/manual seek modes
ELIMINATES:
• Limited inputs on A/V receivers or televisions
• Poor video switching quality from A/V receivers
• Low quality composite to S-video conversion from passive products
• The need for costly digital audio signal conversion products
SUGGESTED USES:
• Add five additional video/audio inputs to an A/V receiver
• Add five additional video/audio inputs to a TV or monitor
• Add source selection capabilities to a single channel modulator
• Create a security system with five video cameras on a single channel or combine
three SVC-52s and maintain IR control with a single remote control
• Combine with SVC-10 to distribute S-video and digital audio up to 1000’ away
over one CAT-5 cable.
model SVS-52
800.999.5225 • www.channelplus.com 11
SPECIFICATIONS: SVS-52
typical @ 25
o
C +_ 5
o
INPUTS & OUTPUTS S-video/composite video 5 inputs x 2 outputs
optical digital audio 3 inputs x 1 output
audio digital/analog 5 inputs x 2 outputs
gain 1.0 nominal (2 ports)
video level 1 V p-p @ 75
audio level 1 V rms @ 47k
VIDEO PERFORMANCE video bandwidth <0.1 dB (0-4 MHz)
crosstalk (0-4 MHz) >70 dB
RS-232 pin out 2 TX, 3 RX, 5 GND
protocol 9600 baud, 8 bit, 1 stop, no parity
POWER SUPPLY model number 350-103
output current 600mA
output voltage 15 Vdc
input power 105-125 Vac
power consumption 8 watts typical
PHYSICAL height 1.75” (4.4 cm)
width 17” (43.2 cm)
depth 6.5” (16.5 cm)
weight 2 lbs, 10 oz (1.19 kg)
Distributed Multi-Source Home Theater Installation
EXPORT MODELS AVAILABLE
(SEE PAGE 49)
12 800.999.5225 • www.channelplus.com
VIDEO DISTRIBUTION
POINT-TO-POINT S-VIDEO DISTRIBUTION SYSTEM
The SVC-10 delivers true, unconverted S-video or composite video, digital audio or
analog audio over CAT-5 up to 1,000 feet away. Simply place the SVC-10 transmitter
at the source and the SVC-10R receiver at a remote location. The integrated IR
makes it possible to control the source with a click of the remote*. Use the SVC-10
to distribute both audio and video or distribute audio alone.
*Target and emitter required
FEATURES:
Transmitter
• Composite and S-video inputs
• Digital, optical digital 5.1, and analog stereo audio inputs
• Auto termination loop-through
• IR emitter and RJ-45 CAT-5 outputs
• 19-inch rack mountable (one space)
• Automatic optical to coax digital audio conversion
• Adjustable picture compensation for length of wire run
Receiver
• Composite and S-video outputs
• Coax digital and analog audio outputs
• 12 volt IR target input
• RJ-45 CAT-5 input
• Compact size
ELIMINATES:
• Ground loop problems
• Stacks of components in remote rooms
• Lack of signal integrity from sending S-video over long runs
• Need for coax or multiple video and audio cables to remote locations
SUGGESTED USES:
Distribute unconverted audio and video from music management system over single
CAT-5 cable
• Provide video and audio access to distant location such as pool house with no
ground looping problems or coax required
• Create cost effective single-zone audio distribution system with unlimited power
and simplified wiring
• Loop several units together for whole house distribution
• Deliver high quality audio and video to box seats in sports arena
• Access home theater from bedroom with full IR remote control
• Combine SVS-52 or SVS-88 (previous pages) to switch between multiple sources
model SVC-10R
(included with SVC-10)
model SVC-10
800.999.5225 • www.channelplus.com 13
SPECIFICATIONS
SVC-10 SVD-8
typical @ 25
o
C +_ 5
o
VIDEO nominal level 1.0 V P-P 1.0 V P-P
impedence 75 75
3 dB bandwidth 15 MHz 15 MHz
(worst case 1,000’)
DIGITAL AUDIO nominal level 0.5 V P-P 0.5 V P-P
impedence 75 75
3 dB bandwidth 15 MHz 15 MHz
(worst case 1,000’)
ANALOG AUDIO nominal level 1 Vrms 1 Vrms
impedence 10 nominal 10 nominal
3 dB bandwidth 20 Hz – 20 KHz 20 Hz – 20 KHz
(worst case 1,000’)
POWER SUPPLY included with domestic product 15 Vdc 600 mA 12 Vdc 2 amps
power consumption (transmitter) 5 watts typical
power consumption (receiver) 5 watts typical 18 watts typical
PHYSICAL transmitter size (H x W x D) 1.75” x 17.0” x 6.5” 12” x 2.4” x 1”
(4.4 cm x 43.2 cm (30 cm x 6 cm x 2.54 cm)
x 16.5 cm)
receiver size (H x W x D) 1.0” x 4.6” x 3.2” N/A
(2.54 cm x 12 cm x 8 cm)
ENVIRONMENTAL shipping weight 3.5 lbs 5 lbs
operating temperature 0°C to 50°C 0°C to 50°C
storage temperature -30°C to 70°C -30°C to 70°C
humidity 5% to 90% non-condensing 5% to 90% non-condensing
SVD-8 DISTRIBUTION PANEL WITH DIFFERENTIAL DRIVE
ENGINE
The SVD-8 distribution panel is a companion product to the SVC-10 point-to-point distribution system. Adding an SVD-8
to the system expands distribution capabilities from one to eight locations with IR capabilities at each. It also doubles the
distance that signals can be distributed to 2,000 feet using CAT-5 wire. Both the SVC-10 and the SVD-8 distribute true,
unconverted S-video, composite video, digital audio, and analog audio. The system is also compatible with SVS-52 five-
source audio video switcher and the SVS-88 eight-way matrix switcher. The system is expandable to 64 outputs.
SUGGESTED USES:
Ideal to send single source to multiple locations over long distance (up to 2,000’)
• Combine the SVS-88, SVS-52, the SVC-10, and the SVD-8 to distribute multiple sources over long distance such as schools,
training facilities, sports bars, video stores, or light commercial applications
• Choose SVD-8 and SVC-10 when high signal integrity is important
model SVD-8
EXPORT MODELS AVAILABLE
(SEE PAGE 49)
14 800.999.5225 • www.channelplus.com
VIDEO DISTRIBUTION
S-VIDEO MODULATORS WITH
THE ULTIMATE IN MTS STEREO
SVM modulators offer complete MTS stereo encoding and S-video inputs in a
full component size rack mountable case.The SVM-22 and SVM-24 are two and
four-channel stereo modulators with 25 dBmV of output and easy push button
digital programming. The SVM series incorporates S-video inputs that support both
S-video and composite video feeds with included adapters. Offering full MTS
stereo with dbx noise reduction and compatibility with Dolby Pro Logic
®
, the
SVMs are ideal for integration into any home theater system.
INTEGRATED IR CONTROL
Each SVM modulator has IR emitter output jacks and is compatible with both
12-volt or 5-volt IR systems. With new desktop power supplies, SVM modulators
can remotely power a DA-550 or DA-8200 series distribution panel from up to
75 feet away.
AUTO-TERMINATION
The SVM series offers full loop-through outputs with 75-ohm auto-termination.
By connecting video/audio cables to the output jacks, you can have all video and
audio signals pass through for use with a local monitor, VCR, or DVR.
RACK SIZE
SVM modulators will fit any 19-inch EIA rack (mounting ears included). The SVM-22
and SVM-24 are one rack space high.
SUGGESTED USES
• When quality video and the ability to distribute S-video are important
• For remotely powering DA series amplifiers
• For installation with other home theater components in a 19-inch EIA rack
model SVM-24
model SVM-22
800.999.5225 • www.channelplus.com 15
SPECIFICATIONS SVM-22 SVM-24
typical @ 25
o
C +_ 5
o
C
INPUTS video: baseband 1.0 V P-P @ 75 1.0 V P-P @ 75
video standard NTSC NTSC
video connector type mini DIN (2) mini DIN (4)
audio: left and right 1.0 Vrms @ 10 k 1.0 Vrms @ 10 k
audio connector type RCA (4) RCA (8)
RF OUTPUTS number of modulators 2 4
tuning range: UHF 14-64 14-64
CATV 65-125 excluding 95-99 65-125 excluding 95-99
maximum output 25 dBmV 25 dBmV
frequency stability +_ 5 KHz +_ 5 KHz
OUTPUTS S-video mini DIN (2) mini DIN (4)
audio connector type RCA (4) RCA (8)
mts stereo yes yes
dbx noise reduction yes yes
5.1 surround sound support yes yes
signal to noise ratio >65 dB >65 dB
separation @ 1000 Hz >25 dB >25 dB
audio frequency range 20Hz to 12 KHz 20Hz to 12 KHz
IR emitter connectors mini jack (2) mini jack (4)
POWER SUPPLY included with product 15 Vdc 900 mA 15 Vdc 900 mA
GENERAL width x height x depth 1.75” x 17” x 6.5” 1.75” x 17” x 6.5”
(4.4 cm x 43.2 cm x 16.5 cm) (4.4 cm x 43.2 cm x 16.5 cm)
shipping weight 2 lbs (1 kg) 2 lbs (1 kg)
operating temperature 32
o
F to 122
o
F (0
o
C to 50
o
C) 32
o
F to 122
o
F (0
o
C to 50
o
C)
Model SVM-22 and SVM-24
16 800.999.5225 • www.channelplus.com
DATA AND TELEPHONE DISTRIBUTION MODULES
ChannelPlus DMD-16 Data Termination Hub provides a superior way to terminate
data connections. Each unit has 16 unbridged 110 punch-down termination
points that are aligned with a corresponding RJ-45 connector. Rated for CAT-5e
performance in data networks, the DMD-16 is an excellent data termination hub
for use with an Ethernet hub for LANs. The DMD-16 can also be used as a
termination point for control signals over CAT-5, video and audio signals, home
control signals, security camera video, and KSU and PBX phone systems.
STRUCTURED WIRE
Telephone Distribution Module
MODEL DMT-16
• Four lines to 16 locations
• Four line surge protection
• Labeling system
• RJ-31X
• Disconnect/test service
Telephone Distribution Module
MODEL DMT-24
• Four lines to 24 locations
• Four line surge protection
• Labeling system
• RJ-31X
• Disconnect/test service
Data Distribution Module
MODEL DMD-16
• CAT-5 certified
• Unbridged termination hub
• 16 data locations
• Labeling system
800.999.5225 • www.channelplus.com 17
ETHERNET ROUTER AND SWITCH
Connection Diagram for H634
Connection Diagram for H638
Ethernet Broadband Residential
Gateway
MODEL H634
• Certified 10/100 Base-T
performance
• Four-port router
• DSL and cable modem input
• Built-in firewall
• RJ-45 connections
• Mounting bracket included
• Replaces 8157
Ethernet Switch
MODEL H638
• Certified 10/100 Base-T
performance
• Eight-port switch
• RJ-45 connections
• Uplink port
• Expandable
• Mounting bracket attached
• Any port may be either input or uplink
• Can be combined with Model H634
18 800.999.5225 • www.channelplus.com
TAP (TOTAL ACCESS PORT) WALL PLATES
TAP (Total Access Port) wall plates come pre-configured and pre-assembled for
fast, sure installations. Pre-assembly eliminates fabrication time. Pre-configuration
eliminates messy plate wiring and wiring mistakes. Merely install coax cable on the
supplied connectors and punch down CAT-5 wire on the 110 punch-down blocks.
Each TAP is self-mapping for clear terminal assignments. No external boxes or
devices are necessary. TAP plates blend in just about anywhere, thanks to a choice
of white, almond and ivory. They are available in four configurations and are
supplied either as single units or in convenient ten-packs.
• Quicker to install
• Eliminates connection errors — TIA 570 color coded
Offers a totally terminated connection in contrast with other systems on the market,
which are incomplete
STRUCTURED WIRE
Telephone/Coax WPx-PC
• Four RJ-25 telephone jacks
• Breaks out each telephone line to an
individual jack
Provisions for two coax barrel connectors
(connectors included)
• Includes one pre-configured 110 punch-
down block plus two coax barrel connectors
Home Theater
Wallplate
WPW-D7.1
• Terminate
speakers for
Dolby
®
5.1,
6.1 or 7.1
• Double-gang
width
• Available in
white only
Data/Telephone WPx-DP
• Single CAT-5e RJ-45 jack and four
RJ-25 telephone jacks
• Breaks out each telephone line to an
individual jack
• Includes two pre-configured 110
punch-down blocks for termination
Data/Telephone/Coax WPx-PDC
• Our most versatile wall plate design
• One CAT-5e RJ-45 jack, two breakout RJ-25
telephone jacks, and two knock outs for
use with coax barrel
connectors (connectors included)
• Includes two pre-configured 110 punch-
down blocks for termination and two coax
barrel connectors
Dual Data WPx-DD
• Two CAT-5e RJ-45 connectors
• Decora
®
compatible design
• Includes two 110 punch-down blocks for
termination
FRONT
BACK
FRONT
BACK
FRONT
BACK
FRONT
BACK
All four TAP wall plates come in
the following colors:
White Almond Ivory
Specify A (almond), I (ivory) or W (white) in the
“x” place of the model number. For instance,
to order a WPx-PC in almond, specify WPA-PC.
To order a ten pack of any model, just add a
“-10” suffix to the model number. For instance,
WPA-PC designates a single unit; WPA-PC-10
designates a 10-pack.
NEW!
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

Channel Plus 5435 User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI