Quikrete 862009 Installation guide

Quikrete
Brand
Quikrete
Model
862009
Type
Installation guide

Quikrete 862009 is a sanded acrylic formula that adheres to brick, block, stone, and concrete surfaces. It is water-resistant, has minimal shrinkage, excellent adhesion, and is non-flammable. The unique square opening is ideal for filling 3/8" mortar joints. It can be used to seal cracks and mortar joints in masonry walls. Joints must be clean, dry, and free of grease, dust, or loose particles. Apply by pushing the cartridge tip over the surface and forcing a bead of caulk into the opening. Apply no thicker than 3/8” (9 mm) in one application.

Quikrete 862009 is a sanded acrylic formula that adheres to brick, block, stone, and concrete surfaces. It is water-resistant, has minimal shrinkage, excellent adhesion, and is non-flammable. The unique square opening is ideal for filling 3/8" mortar joints. It can be used to seal cracks and mortar joints in masonry walls. Joints must be clean, dry, and free of grease, dust, or loose particles. Apply by pushing the cartridge tip over the surface and forcing a bead of caulk into the opening. Apply no thicker than 3/8” (9 mm) in one application.

M
M
M
O
O
O
R
R
R
T
T
T
A
A
A
R
R
R
R
R
R
E
E
E
P
P
P
A
A
A
I
I
I
R
R
R
P
P
P
R
R
R
O
O
O
D
D
D
U
U
U
C
C
C
T
T
T
N
N
N
O
O
O
.
.
.
8
8
8
6
6
6
2
2
2
0
0
0
PRODUCT USE
QUIKRETE
®
Mortar Repair is a water- resistant acrylic formula that
remains relatively flexible. It is textured and colored to give the
appearance of masonry mortar. The product has minimal shrinkage,
excellent adhesion, and is non-flammable. The unique square
opening is ideal for filling 3/8" mortar joints.
SIZES
• QUIKRETE
®
Mortar Repair - 10.1 oz (296 ml) caulking tubes and
5.5 oz (163 ml) squeeze tubes
YIELD
• Each 10.1 fl oz. (296 ml) tube of QUIKRETE
®
Mortar Repair will fill a
3/8”x 3/8" (10 mm x 10 mm) mortar joint 12 ft. (3.7 M) long.
.
INSTALLATION
Use to seal cracks and mortar joints in masonry walls.
• Joints must be clean, dry, and free of grease, dust, or loose
particles. Remove all loose mortar from the joint before filling.
• Puncture seal inside the applicator tip. Use cartridge in standard
caulking gun.
• Apply by pushing cartridge tip over surface and forcing bead of
caulking into the opening. Apply no thicker than 3/8” (9 mm) in one
application.
• Tip of applicator acts as a tool to smooth the surface.
• Excess can be wiped off with a damp cloth.
• Can be painted after 24 hr. Use latex paints only.
PRECAUTIONS
• Do not apply if rain threatens or is predicted within 12 hours. Not for
use as a structural repair of badly damaged walls. Protect from
freezing. Store between 35
o
F (2
o
C) and 100
o
F (38
o
C). Air and surface
temperature should be above 40
o
F (4
o
C) for proper application.
• Do not use to fill control / expansion joints.
• Do not apply where temperatures may reach 140
o
F (60
o
C) or higher
(fireplaces, electric wires, etc.)
CAUTION
May cause eye, skin, and respiratory irritation. Avoid breathing vapor
and contact with eyes, skin, and clothing. Use only with adequate
ventilation. Ingestion may cause irritation.
WARRANTY
The QUIKRETE
®
Companies warrant this product to be of
merchantable quality when used or applied in accordance with the
instructions herein. The product is not warranted as suitable for any
purpose or use other than the general purpose for which it is
intended. Liability under this warranty is limited to the replacement of
its product (as purchased) found to be defective, or at the shipping
companies’ option, to refund the purchase price. In the event of a
claim under this warranty, notice must be given to The QUIKRETE
®
Companies in writing. This limited warranty is issued and accepted in
lieu of all other express warranties and expressly excludes liability for
consequential damages.
The QUIKRETE
®
Companies
One Securities Centre
3490 Piedmont Rd., NE, Suite 1300, Atlanta, GA 30305
(404) 634-9100 • Fax: (404) 842-1425
PRODUCT DESCRIPTION
QUIKRETE
®
Mortar Repair is a sanded acrylic formula that adheres to brick, block,
stone
,
and concrete surfaces.
* Refer to www.quikrete.com for the most current technical data, MSDS, and guide specifications
Masonry Accessories
04 05 23
DIVISION 4
  • Page 1 1

Quikrete 862009 Installation guide

Quikrete
Brand
Quikrete
Model
862009
Type
Installation guide

Quikrete 862009 is a sanded acrylic formula that adheres to brick, block, stone, and concrete surfaces. It is water-resistant, has minimal shrinkage, excellent adhesion, and is non-flammable. The unique square opening is ideal for filling 3/8" mortar joints. It can be used to seal cracks and mortar joints in masonry walls. Joints must be clean, dry, and free of grease, dust, or loose particles. Apply by pushing the cartridge tip over the surface and forcing a bead of caulk into the opening. Apply no thicker than 3/8” (9 mm) in one application.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents