Palram 702562 Product information

Type
Product information
PALRAM
Assembly
Instructions
Skylight
ShedTM - Shelf
Approx. Dim.
83L x 30W
x 19H cm / 32.6"L x 11.8 "Wx 7.4 "H
After Sale
Service
Email: customer.service
@palram.com
USA 877 -627 -8476 I England 01302
-380775 I France 0169 -791 -094
Canada 1 800 -866 -5749 Germany 0180 -522
-8778 International +972 4- 848 -6942
www.palramapplications.com
IMPORTANT
Please read these instructions carefully before you start to assemble this shelf.
Please carry out the steps in the order set out in these instructions.
Keep these instructions in a safe place for future reference.
Tools & Equipment
(supplied)
Before Assembly
Rt Sort the parts and check according to the contents parts list.
Rt Some parts may have sharp edges. Please be careful when handling components.
Rt Following are a number of illustrations depicting possibilities for mounting the SkyLight
shelf on all Palram SkyLight Shed sizes.
4x6 6x3 6x5, 6x8, 6x1 0, 6x12
Rt It is highly recommended to plan the assembly prior to starting, according to one of the following options:
Rt Once you have chosen your preferable option please go to the appropriate page in the Assembly Instructions.
Option #1:
Mounting the shelf in the
middle of the side wall
(Page 1)
(Not suitable for 4x6 shed)
Attention:
Option #2:
Mounting the shelf where the
shelf's left side connects with the
shed's corner (Pages 2 -3)
"111I
aa.
V Do not mount more than 2 shelves onto one panel.
Do not mount more than 4 shelves on a single wall.
Under any circumstance do not mount more than 10 shelves per shed.
A single shelf can carry up to 30 kg (66 lbs).
Option #3:
Mounting the shelf where the
shelf's right side connects with the
shed's corner (Pages 4 -5)
Option #4:
Mounting the shelf side by side
(only at the shed's rear wall)
(Page 6)
.M11
(Not suitable for 4x6 shed)
During Assembly
Panel ( #8076) is not pre -drilled; therefore you must drill the holes with
accordance to your chosen option.
Rt Metal plate ( #8075) is used to mounting the shelf onto either one of the
shed's corners. If you did not choose this option, there is no need to use
this part; keep it for future use if needed.
V Tighten all screws when completing assembly.
Do not tighten screws and nuts (411 & 412) until completion of assembly process.
These 2 icons indicate if screws' tightening is required or not.
A
[pee
51
N
Contents
Item Qty.
8076
8074
8073
8075
o
o
o
1
1
1
1
Item
8077
466
461
411
T001
1
Option
#1
11
C)
L
461
. II
2
Option
#2
466
Sa=2,
,461
3
Option
#2
r
-,-------____
461
.
4
Option
#3
[AD---
461
461
0f0
4
6
eiÖ
top
5
Option
#3
461
(16
el
%
6
Option
#4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18

Palram 702562 Product information

Type
Product information

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI