Aeg-Electrolux S73000DSW0 User manual

Page is loading ...

FOR PERFECT RESULTS

Thank you for choosing this AEG product. We have

created it to give you impeccable performance for many

years, with innovative technologies that help make life

simpler – features you might not find on ordinary

appliances. Please spend a few minutes reading to get the

very best from it.

ACCESSORIES AND CONSUMABLES

In the AEG webshop, you’ll find everything you need to

keep all your AEG appliances looking spotless and

working perfectly. Along with a wide range of accessories

designed and built to the high quality standards you

would expect, from specialist cookware to cutlery baskets,

from bottle holders to delicate laundry bags…

Visit the webshop at:

www.aeg.com/shop

20

CONTENTS

22 Safety information

24 Operation

25 First use

26 Daily use

27 Helpful hints and tips

29 What to do if…

31 Technical data

31 Installation

34 Noises

36 Environmental concerns

The following symbols are used in this user

manual:

Important information concerning your

personal safety and information on how to

avoid damaging the appliance.

General information and tips

Environmental information

Subject to change without notice

Contents

21

SAFETY INFORMATION

In the interest of your safety and to ensure the correct use, before installing and first using

the appliance, read this user manual carefully, including its hints and warnings. To avoid

unnecessary mistakes and accidents, it is important to ensure that all people using the ap-

pliance are thoroughly familiar with its operation and safety features. Save these instruc-

tions and make sure that they remain with the appliance if it is moved or sold, so that ev-

eryone using it through its life will be properly informed on appliance use and safety.

For the safety of life and property keep the precautions of these user's instructions as the

manufacturer is not responsible for damages caused by omission.

Children and vulnerable people safety

• This appliance is not intended for use by persons (including children) with reduced physi-

cal, sensory or mental capabilities, or lack of experience and knowledge, unless they have

been given supervision or instruction concerning use of the appliance by a person re-

sponsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

• Keep all packaging well away from children. There is risk of suffocation.

• If you are discarding the appliance pull the plug out of the socket, cut the connection

cable (as close to the appliance as you can) and remove the door to prevent playing chil-

dren to suffer electric shock or to close themselves into it.

• If this appliance featuring magnetic door seals is to replace an older appliance having a

spring lock (latch) on the door or lid, be sure to make that spring lock unusable before

you discard the old appliance. This will prevent it from becoming a death trap for a child.

General safety

WARNING!

Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of

obstruction.

• The appliance is intended for keeping foodstuff and/or beverages in a normal household

as explained in this instruction booklet.

• Do not use a mechanical device or any artificial means to speed up the thawing process.

• Do not use other electrical appliances (such as ice cream makers) inside of refrigerating

appliances, unless they are approved for this purpose by the manufacturer.

• Do not damage the refrigerant circuit.

• The refrigerant isobutane (R600a) is contained within the refrigerant circuit of the appli-

ance, a natural gas with a high level of environmental compatibility, which is neverthe-

less flammable.

During transportation and installation of the appliance, be certain that none of the com-

ponents of the refrigerant circuit become damaged.

If the refrigerant circuit should become damaged:

– avoid open flames and sources of ignition

22 Safety information

– thoroughly ventilate the room in which the appliance is situated

• It is dangerous to alter the specifications or modify this product in any way. Any damage

to the cord may cause a short-circuit, fire and/or electric shock.

WARNING!

Any electrical component (power cord, plug, compressor) must be replaced by a certified

service agent or qualified service personnel to avoid hazard.

1. Power cord must not be lengthened.

2. Make sure that the power plug is not squashed or damaged by the back of the ap-

pliance. A squashed or damaged power plug may overheat and cause a fire.

3. Make sure that you can come to the mains plug of the appliance.

4. Do not pull the mains cable.

5. If the power plug socket is loose, do not insert the power plug. There is a risk of

electric shock or fire.

6.

You must not operate the appliance without the lamp cover

5)

of interior lighting.

• This appliance is heavy. Care should be taken when moving it.

• Do not remove nor touch items from the freezer compartment if your hands are damp/

wet, as this could cause skin abrasions or frost/freezer burns.

• Avoid prolonged exposure of the appliance to direct sunlight.

•

Bulb lamps

6)

used in this appliance are special purpose lamps selected for household ap-

pliances use only. They are not suitable for household room illumination.

Daily Use

• Do not put hot pot on the plastic parts in the appliance.

• Do not store flammable gas and liquid in the appliance, because they may explode.

•

Do not place food products directly against the air outlet on the rear wall.

7)

• Frozen food must not be re-frozen once it has been thawed out.

• Store pre-packed frozen food in accordance with the frozen food manufacturer's in-

structions.

• Appliance's manufacturers storage recommendations should be strictly adhered to. Refer

to relevant instructions.

• Do not place carbonated or fizzy drinks in the freezer compartment as it creates pressure

on the container, which may cause it to explode, resulting in damage to the appliance.

• Ice lollies can cause frost burns if consumed straight from the appliance.

Care and cleaning

• Before maintenance, switch off the appliance and disconnect the mains plug from the

mains socket.

• Do not clean the appliance with metal objects.

• Do not use sharp objects to remove frost from the appliance. Use a plastic scraper.

5) If the lamp cover is foreseen.

6) If the lamp is foreseen.

7) If the appliance is Frost Free.

Safety information 23

• Regularly examine the drain in the refrigerator for defrosted water. If necessary, clean

the drain. If the drain is blocked, water will collect in the bottom of the appliance.

Installation

For electrical connection carefully follow the instructions given in specific paragraphs.

• Unpack the appliance and check if there are damages on it. Do not connect the appli-

ance if it is damaged. Report possible damages immediately to the place you bought it.

In that case retain packing.

• It is advisable to wait at least four hours before connecting the appliance to allow the oil

to flow back in the compressor.

• Adequate air circulation should be around the appliance, lacking this leads to overheat-

ing. To achieve sufficient ventilation follow the instructions relevant to installation.

• Wherever possible the back of the product should be against a wall to avoid touching or

catching warm parts (compressor, condenser) to prevent possible burn.

• The appliance must not be located close to radiators or cookers.

• Make sure that the mains plug is accessible after the installation of the appliance.

•

Connect to potable water supply only.

8)

Service

• Any electrical work required to do the servicing of the appliance should be carried out by

a qualified electrician or competent person.

• This product must be serviced by an authorized Service Centre, and only genuine spare

parts must be used.

Environment Protection

This appliance does not contain gasses which could damage the ozone layer, in either its

refrigerant circuit or insulation materials. The appliance shall not be discarded together

with the urban refuse and rubbish. The insulation foam contains flammable gases: the ap-

pliance shall be disposed according to the applicable regulations to obtain from your local

authorities. Avoid damaging the cooling unit, especially at the rear near the heat exchang-

er. The materials used on this appliance marked by the symbol

are recyclable.

OPERATION

Switching on

Insert the plug into the wall socket.

Turn the Temperature regulator clockwise to a medium setting.

Switching off

To turn off the appliance, turn the Temperature regulator to the "O" position.

8) If a water connection is foreseen.

24 Operation

Temperature regulation

The temperature is automatically regulated.

To operate the appliance, proceed as follows:

• turn the Temperature regulator toward lower settings to obtain the minimum coldness.

• turn the Temperature regulator toward higher settings to obtain the maximum coldness.

A medium setting is generally the most suitable.

However, the exact setting should be chosen keeping in mind that the temperature inside

the appliance depends on:

• room temperature

• how often the door is opened

• the quantity of food stored

• the location of the appliance.

If the ambient temperature is high or the appliance is fully loaded, and the appliance is set

to the lowest temperatures, it may run continuously causing frost to form on the rear wall.

In this case the dial must be set to a higher temperature to allow automatic defrosting and

therefore reduced energy consumption.

FIRST USE

Cleaning the interior

Before using the appliance for the first time, wash the interior and all internal accessories

with lukewarm water and some neutral soap so as to remove the typical smell of a brand-

new product, then dry thoroughly.

Do not use detergents or abrasive powders, as these will damage the finish.

First use

25

DAILY USE

Movable shelves

The walls of the refrigerator are equipped with a

series of runners so that the shelves can be posi-

tioned as desired.

Bottle rack

Place the bottles (with the opening facing front)

in the pre-positioned shelf.

If the shelf is positioned horizontally, place only

closed bottles.

This bottle holder shelf can be tilted in order to

store previously opened bottles. To obtain this re-

sult, pull the shelf up so it can rotate upwards and

be placed on the next higher level.

Positioning the door shelves

To permit storage of food packages of various sizes, the door shelves can be placed at dif-

ferent heights.

Frozen Food Calendar

The symbols show different types of frozen goods.

The numbers indicate storage times in months for the appropriate types of frozen goods.

Whether the upper or lower value of the indicated storage time is valid depends on the

quality of the foods and treating before freezing.

Freezing fresh food

The freezer compartment is suitable for freezing fresh food and storing frozen and deep-

frozen food for a long time.

26 Daily use

To freeze fresh foods it is not necessary to change the medium setting.

Move the shelf present in the freezer compartment to the upper seat, keeping it horizontal.

Place the fresh food to be frozen on that shelf.

However, for a faster freezing operation, turn the temperature regulator toward higher set-

tings to obtain the maximum coldness.

In this condition, the refrigerator compartment temperature might drop below 0°C. If this

occurs reset the temperature regulator to a warmer setting.

Storage of frozen food

When first starting-up or after a period out of use, before putting the products in the com-

partment let the appliance run at least 2 hours on the higher settings.

In the event of accidental defrosting, for example due to a power failure, if the power has

been off for longer than the value shown in the technical characteristics chart under "rising

time", the defrosted food must be consumed quickly or cooked immediately and then re-

frozen (after cooling).

Thawing

Deep-frozen or frozen food, prior to being used, can be thawed in the refrigerator compart-

ment or at room temperature, depending on the time available for this operation.

Small pieces may even be cooked still frozen, directly from the freezer: in this case, cooking

will take longer.

Ice-cube production

This appliance is equipped with one or more trays for the production of ice-cubes. Fill these

trays with water, then put them in the freezer compartment.

Do not use metallic instruments to remove the trays from the freezer.

HELPFUL HINTS AND TIPS

Hints for energy saving

• Do not open the door frequently or leave it open longer than absolutely necessary.

• If the ambient temperature is high and the Temperature Regulator is set to low tempera-

ture and the appliance is fully loaded, the compressor may run continuously, causing

frost or ice on the evaporator. If this happens, set the Temperature Regulator toward

warmer settings to allow automatic defrosting and so a saving in electricity consump-

tion.

Hints for fresh food refrigeration

To obtain the best performance:

• do not store warm food or evaporating liquids in the refrigerator

• do cover or wrap the food, particularly if it has a strong flavour

• position food so that air can circulate freely around it

Helpful hints and tips

27

Hints for refrigeration

Useful hints:

Meat (all types) : wrap in polythene bags and place on the glass shelf above the vegetable

drawer.

For safety, store in this way only one or two days at the most.

Cooked foods, cold dishes, etc..: these should be covered and may be placed on any shelf.

Fruit and vegetables: these should be thoroughly cleaned and placed in the special draw-

er(s) provided.

Butter and cheese: these should be placed in special airtight containers or wrapped in alu-

minium foil or polythene bags to exclude as much air as possible.

Milk bottles: these should have a cap and should be stored in the bottle rack on the door.

Bananas, potatoes, onions and garlic, if not packed, must not be kept in the refrigerator.

Hints for freezing

To help you make the most of the freezing process, here are some important hints:

• the maximum quantity of food which can be frozen in 24 hrs. is shown on the rating

plate;

• the freezing process takes 24 hours. No further food to be frozen should be added during

this period;

• only freeze top quality, fresh and thoroughly cleaned, foodstuffs;

• prepare food in small portions to enable it to be rapidly and completely frozen and to

make it possible subsequently to thaw only the quantity required;

• wrap up the food in aluminium foil or polythene and make sure that the packages are

airtight;

• do not allow fresh, unfrozen food to touch food which is already frozen, thus avoiding a

rise in temperature of the latter;

• lean foods store better and longer than fatty ones; salt reduces the storage life of food;

• water ices, if consumed immediately after removal from the freezer compartment, can

possibly cause the skin to be freeze burnt;

• it is advisable to show the freezing in date on each individual pack to enable you to keep

tab of the storage time.

Hints for storage of frozen food

To obtain the best performance from this appliance, you should:

• make sure that the commercially frozen foodstuffs were adequately stored by the retail-

er;

• be sure that frozen foodstuffs are transferred from the foodstore to the freezer in the

shortest possible time;

• not open the door frequently or leave it open longer than absolutely necessary.

• Once defrosted, food deteriorates rapidly and cannot be refrozen.

• Do not exceed the storage period indicated by the food manufacturer.

28 Helpful hints and tips

WHAT TO DO IF…

WARNING!

Before troubleshooting, disconnect the mains plug from the mains socket.

Only a qualified electrician or competent person must do the troubleshooting that is not in

this manual.

There are some sounds during normal use (compressor, refrigerant circulation).

Problem Possible cause Solution

The appliance does not

operate. The lamp does

not operate.

The appliance is switched off. Switch on the appliance.

The mains plug is not connected

to the mains socket correctly.

Connect the mains plug to the

mains socket correctly.

The appliance has no power.

There is no voltage in the mains

socket.

Connect a different electrical ap-

pliance to the mains socket.

Contact a qualified electrician.

The lamp does not work. The lamp is in stand-by. Close and open the door.

The lamp is defective. Refer to "Replacing the lamp".

The compressor operates

continually.

The temperature is not set cor-

rectly.

Set a higher temperature.

The door is not closed correctly. Refer to "Closing the door".

The door has been opened too

frequently.

Do not keep the door open longer

than necessary.

The product temperature is too

high.

Let the product temperature de-

crease to room temperature be-

fore storage.

The room temperature is too

high.

Decrease the room temperature.

Water flows on the rear

plate of the refrigerator.

During the automatic defrosting

process, frost defrosts on the

rear plate.

This is correct.

Water flows into the re-

frigerator.

The water outlet is clogged. Clean the water outlet.

Products prevent that water

flows into the water collector.

Make sure that products do not

touch the rear plate.

Water flows on the

ground.

The melting water outlet does

not flow in the evaporative tray

above the compressor.

Attach the melting water outlet

to the evaporative tray.

The temperature in the

appliance is too low.

The temperature regulator is not

set correctly.

Set a higher temperature.

What to do if… 29

Problem Possible cause Solution

The temperature in the

appliance is too high.

The temperature regulator is not

set correctly.

Set a lower temperature.

The door is not closed correctly. Refer to "Closing the door".

The product temperature is too

high.

Let the product temperature de-

crease to room temperature be-

fore storage.

Many products are stored at the

same time.

Store less products at the same

time.

There is no cold air circulation in

the appliance.

Make sure that there is cold air

circulation in the appliance.

Replacing the lamp

1. Disconnect the mains plug from the mains socket.

2. Remove the screw from the lamp cover.

3. Remove the lamp cover (refer to the il-

lustration).

4. Replace the used lamp with a new lamp

of the same power and specifically de-

signed for household appliances. (the

maximum power is shown on the lamp

cover).

5. Install the lamp cover.

6. Tighten the screw to the lamp cover.

7. Connect the mains plug to the mains socket.

8. Open the door. Make sure that the lamp comes on.

Closing the door

1. Clean the door gaskets.

2. If necessary, adjust the door. Refer to "Installation".

3. If necessary, replace the defective door gaskets. Contact the Service Center.

30 What to do if…

TECHNICAL DATA

Dimension of the recess

Height 1600 mm

Width 600 mm

Depth 645 mm

Rising Time 25 h

Voltage 230-240 V

Frequency 50 Hz

The technical information are situated in the rating plate on the internal left side of the

appliance and in the energy label.

INSTALLATION

WARNING!

Read the "Safety Information" carefully for your safety and correct operation of the appli-

ance before installing the appliance.

Positioning

Install this appliance at a location where the ambient temperature corresponds to the cli-

mate class indicated on the rating plate of the appliance:

Climate class Ambient temperature

SN +10°C to + 32°C

N +16°C to + 32°C

ST +16°C to + 38°C

T +16°C to + 43°C

Location

The appliance should be installed well away from sources of heat such as radiators, boilers,

direct sunlight etc. Ensure that air can circulate freely around the back of the cabinet. To

ensure best performance, if the appliance is positioned below an overhanging wall unit, the

minimum distance between the top of the cabinet and the wall unit must be at least 100

mm . Ideally, however, the appliance should not be positioned below overhanging wall

units. Accurate levelling is ensured by one or more adjustable feet at the base of the cabi-

net.

WARNING!

It must be possible to disconnect the appliance from the mains power supply; the plug

must therefore be easily accessible after installation.

Technical data

31

10 mm

100 mm

AB

Electrical connection

Before plugging in, ensure that the voltage and frequency shown on the rating plate corre-

spond to your domestic power supply.

The appliance must be earthed. The power supply cable plug is provided with a contact for

this purpose. If the domestic power supply socket is not earthed, connect the appliance to a

separate earth in compliance with current regulations, consulting a qualified electrician.

The manufacturer declines all responsibility if the above safety precautions are not ob-

served.

This appliance complies with the E.E.C. Directives.

Rear spacers

Inside the appliance you find two spacers which

must be fitted as shown in the figure.

Slacken the screws and insert the spacer under

the screw head, then retighten the screws.

32 Installation

Door reversibility

WARNING!

Before carrying out any operations, remove the mains plug from the power socket.

To carry out the following operations, we suggest that this be made with another person

that will keep a firm hold on the doors of the appliance during the operations.

To change the opening direction of the door, do these steps:

1. Slide the bottom door off the middle

hinge (H). Remove the middle hinge by

unscrewing the fixing screws.

Make sure to remove the plastic spacer

inserted under the hinge.

2. Slide the top door off the pin (G). Un-

screw the pin (G) and install it on the

opposite side.

3. Remove the two plugs from the middle

crossbeam and install them on the op-

posite side, covering the holes left free

from the removed hinge.

4. Remove the plugs (1) on the upper side

of both doors and move them to the

other side.

H

G

1

Installation 33

5. Remove with a tool the cover (e), un-

screw the lower hinge pivot (f) using a

10 mm spanner and re-screw it on the

opposite side.

6. Install the cover (e) on the opposite side.

7. Install the top door on the pin (G). Insert

the pivot of the middle hinge (H) into

the hole of the top door. Make sure that

the plastic space is placed under the

hinge. Install the bottom door on the

lower hinge pivot (f). Slightly tilting the

doors insert the pivot of the middle

hinge (H) into the hole of the bottom

door.

8. Keeping the doors open, tighten the middle hinge with two screws.

9. Unscrew the handle. Remove the plug

with a punch. Install the handle and the

plug on opposite side. Take from the ac-

cessory bag the two plugs and cover the

holes left open after having removed

the handle.

10. Make sure that the front board of the

door is parallel to the front board of the

top.

11. Reposition, level the appliance, wait for

at least four hours and then connect it

to the power socket.

Do a final check to make sure that:

• All screws are tightened.

• The magnetic seal adheres to the cabinet.

• The door opens and closes correctly.

If the ambient temperature is cold (i.e. in Winter), the gasket may not fit perfectly to the

cabinet. In that case, wait for the natural fitting of the gasket.

NOISES

There are some sounds during normal running (compressor, refrigerant circulation).

1

2

5

3

4

e

f

34 Noises

Page is loading ...

HISSS!

SSSRRR!

CRACK!

ENVIRONMENTAL CONCERNS

The symbol on the product or on its packaging indicates that this product may not be

treated as household waste. Instead it should be taken to the appropriate collection point

for the recycling of electrical and electronic equipment. By ensuring this product is

disposed of correctly, you will help prevent potential negative consequences for the

environment and human health, which could otherwise be caused by inappropriate waste

handling of this product. For more detailed information about recycling of this product,

please contact your local council, your household waste disposal service or the shop where

you purchased the product.

36 Environmental concerns

Page is loading ...

www.aeg.com/shop 222346426-A-072011