Black & Decker BDCR20C User manual

Category
Power tools
Type
User manual
INSTRUCTION MANUAL
20V MAX* RECIPROCATING SAW
Thank you for choosing BLACK+DECKER!
PLEASE READ BEFORE RETURNING THIS PRODUCT FOR
ANY REASON.
If you have a question or experience a problem with your BLACK+DECKER
purchase, go to http://www.blackanddecker.com/instantanswers
If you cant find the answer or do not have access to the Internet, call
1-800-544-6986 from 8 a.m. to 5 p.m. EST Mon. - Fri. to speak with an agent.
Please have the catalog number available when you call.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
VEA EL ESPANOL EN LA CONTRAPORTADA.
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA.
ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.
*Maximum initial battery pack voltage (measured without a workload) is 20 volts. Measured
under a workload, nominal voltage is 18.
CATALOG NUMBER
BDCR20
To register your new product, call 1-800-544-6986
or visit www.BlackandDecker.com/NewOwner
2
SAFETY GUIDELINES - DEFINITIONS
It is important for you to read and understand this manual. The information it contains relates to
protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help
you recognize this information.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION: Indicates a potentially haz ard ous situation which, if not avoided, may
result in minor or mod er ate injury.
NOTICE: Used without the safety alert symbol indicates potentially hazardous
situation which, if not avoided, may result in property damage.
WARNING: Read all safety
warnings and all instructions.
Failure to follow the warnings and
instructions may result in electric
shock, fire and/or serious injury.
SAVE ALL WARNINGS AND
INSTRUCTIONS FOR FUTURE
REFERENCE
The term “power tool” in the
warnings refers to your mains-
operated (corded) power tool
or battery-operated (cordless)
power tool.
SAVE THESE INSTRUCTIONS
1) WORK AREA SAFETY
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in
explosive atmospheres, such as in the
presence of flammable liquids, gases
or dust. Power tools create sparks which
may ignite the dust or fumes.
c) Keep children and bystanders
away while operating a power tool.
Distractions can cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the
outlet. Never modify the plug in any
way. Do not use any adapter plugs
with earthed (grounded) power tools.
Unmodified plugs and matching outlets
will reduce risk of electric shock.
b) Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators.
There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain
or wet conditions. Water entering
a power tool will increase the risk of
electric shock.
d) Do not abuse the cord. Never use
the cord for carrying, pulling or
unplugging the power tool. Keep
cord away from heat, oil, sharp
edges or moving parts. Damaged or
entangled cords increase the risk of
electric shock.
e) When operating a power tool
outdoors, use an extension cord
suitable for outdoor use. Use of a
cord suitable for outdoor use reduces
the risk of electric shock.
f) If operating a power tool in a damp
location is unavoidable, use a
ground fault circuit interrupter
(GFCI) protected supply. Use of a
GFCI reduces the risk of electric shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are
doing and use common sense
when operating a power tool. Do
not use a power tool while you
are tired or under the influence of
drugs, alcohol or medication. A
moment of inattention while operating
power tools may result in serious
personal injury.
b) Use personal protective equipment.
Always wear eye protection.
Protective equipment such as dust
mask, nonskid safety shoes, hard
hat, or hearing protection used for
appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting.
Ensure the switch is in the off
position before connecting to power
source and/ or battery pack, picking
up or carrying the tool. Carrying
power tools with your finger on the
switch or energizing power tools that
have the switch on invites accidents.
d) Remove any adjusting key or
wrench before turning the power
tool on. A wrench or a key left
attached to a rotating part of the power
tool may result in personal injury.
e) Do not overreach. Keep proper
footing and balance at all times.
This enables better control of the
3
power tool in unexpected situations.
f) Dress properly. Do not wear loose
clothing or jewelry. Keep your hair,
clothing and gloves away from
moving parts. Loose clothes, jewelry or
long hair can be caught in moving parts.
g) If devices are provided for the
connection of dust extraction and
collection facilities, ensure these
are connected and properly used.
Use of dust collection can reduce
dust-related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use
the correct power tool for your
application. The correct power tool
will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the
switch does not turn it on and
off. Any power tool that cannot be
controlled with the switch is dangerous
and must be repaired.
c) Disconnect the plug from the
power source and/or the battery
pack from the power tool before
making any adjustments, changing
accessories, or storing power tools.
Such preventive safety measures
reduce the risk of starting the power
tool accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or
these instructions to operate the
power tool. Power tools are dangerous
in the hands of untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving
parts, breakage of parts and any
other condition that may affect the
power tool’s operation. If damaged,
have the power tool repaired before
use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely to
bind and are easier to control.
g) Use the power tool, accessories
and tool bits, etc. in accordance
with these instructions, taking into
account the working conditions and
the work to be performed. Use of
the power tool for operations different
from those intended could result in a
hazardous situation.
5) BATTERY TOOL USE AND CARE
a) Recharge only with the charger
specified by the manufacturer. A
charger that is suitable for one type of
battery pack may create a risk of fire
when used with another battery pack.
b) Use power tools only with
specifically designated battery
packs. Use of any other battery packs
may create a risk of injury and fire.
c) When battery pack is not in use,
keep it away from other metal
objects like paper clips, coins, keys,
nails, screws, or other small metal
objects that can make a connection
from one terminal to another.
Shorting the battery terminals together
may cause burns or a fire.
d) Under abusive conditions,
liquid may be ejected from the
battery, avoid contact. If contact
accidentally occurs, flush with
water. If liquid contacts eyes,
additionally seek medical help.
Liquid ejected from the battery may
cause irritation or burns.
6) SERVICE
a) Have your power tool serviced by a
qualified repair person using only
identical replacement parts. This will
ensure that the safety of the power
tool is maintained.
SPECIFIC SAFETY RULES
Hold power tool by insulated gripping
surfaces, when performing an
operation where the cutting accessory
may contact hidden wiring. Cutting
accessory contacting a “live” wire may
make exposed metal parts of the power
tool “live” and could give the operator an
electric shock.
Use clamps or another practical way
to secure and support the workpiece
to a stable platform. Holding the work
by hand or against your body leaves it
unstable and may lead to loss of control.
When not in use, place tool on its
side on a stable surface where it will
not cause a tripping or falling hazard.
Some tools with large battery packs will stand
upright but may be easily knocked over.
Keep hands away from cutting area.
Never reach underneath the material for
any reason. Hold front of saw by grasping
the contoured gripping area. Do not insert
fingers or thumb into the vicinity of the
reciprocating blade and blade clamp. Do
not stabilize the saw by gripping the shoe.
Keep blades sharp. Dull blades may
cause the saw to swerve or stall under
pressure.
Use extra caution when cutting
overhead and pay particular attention
to overhead wires which may be hidden
from view. Anticipate the path of falling
branches and debris ahead of time.

When cutting pipe or conduit ensure that they
are free from water, electrical wiring, etc.
4
WARNING: Always wear proper
personal hearing protection that
conforms to ANSI S12.6 (S3.19) during
use. Under some conditions and duration
of use, noise from this product may
contribute to hearing loss.
WARNING: ALWAYS use safety
glasses. Everyday eyeglasses are NOT
safety glasses. Also use face or dust
mask if cutting operation is dusty.
ALWAYS WEAR CERTIFIED SAFETY
EQUIPMENT:




protection.
WARNING: Some dust created by
power sanding, sawing, grinding,
drilling, and other construction
activities contains chemicals known to
the state of California to cause cancer,
birth defects or other reproductive
harm. Some examples of these
chemicals are:
• leadfromlead-basedpaints,
• crystallinesilicafrombricksandcement
and other masonry products, and
• arsenicandchromiumfrom
chemically-treated lumber.
Your risk from these exposures varies,
depending on how often you do this type
of work. To reduce your exposure to these
chemicals: work in a well ventilated area,
and work with approved safety equipment,
such as those dust masks that are specially
designed to filter out microscopic particles.
Avoid prolonged contact with dust
from power sanding, sawing, grinding,
drilling, and other construction
activities. Wear protective clothing
and wash exposed areas with soap
and water. Allowing dust to get into your
mouth, eyes, or lay on the skin may
promote absorption of harmful chemicals.
WARNING: Use of this tool can
generate and/or disperse dust, which may
cause serious and permanent respiratory
or other injury. Always use NIOSH/OSHA
approved respiratory protection
appropriate for the dust exposure. Direct
particles away from face and body.
WARNING: Do not operate this
tool for long periods of time. Vibration
caused by the operating action of this tool
may cause permanent injury to fingers,
hands, and arms. Use gloves to provide
extra cushion, take frequent rest periods,
and limit daily time of use.

When using an extension cord, be sure to
use one heavy enough to carry the current
your product will draw. An undersized cord
will cause a drop in line voltage resulting
in loss of power and overheating. The
following table shows the correct size
to use depending on cord length and
nameplate ampere rating. If in doubt, use
the next heavier gage. The smaller the
gage number, the heavier the cord.
SAVE THESE INSTRUCTIONS
SYMBOLS
The label on your tool may include the
following symbols. The symbols and their
definitions are as follows:
V ..................volts
A ..................amperes
Hz ................hertz
W .................watts
min ..............minutes
or AC ...... alternating current
or DC ...direct current
n
o ................no load speed
................Class I Construction
(grounded)
................earthing terminal
...............safety alert symbol
................Class II Construction
(double insulated)
.../min or rpm...revolutions or
reciprocation per minute
SPM ............Strokes per minute
............ Read instruction manual
before use
................Use proper eye protection
................ Use proper hearing
protection
................
Use proper respiratory
protection
IMPORTANT SAFETY
INSTRUCTIONS FOR
BATTERY CHARGERS
SAVE THESE INSTRUCTIONS: This
manual contains important safety
instructions for battery chargers.
Before using charger, read all instructions
and cautionary markings on charger,
battery pack, and product using battery
pack.
WARNING: Shock hazard. Do not
allow any liquid to get inside charger.
CAUTION: Burn hazard.
To reduce
the risk of injury, charge only designated
BLACK+DECKER batteries. Other types
of batteries may burst causing personal
injury and damage.
Minimum Gauge for Cord Sets
Volts Total Length of Cord in Feet
    

Ampere Rating
More Not more American Wire Gauge
Than Than
    
CAUTION: Under certain conditions,
with the charger plugged in to the power
supply, the charger can be shorted by
foreign material. Foreign materials of a
conductive nature such as, but not li
mited
to, steel wool, aluminum foil, or any buildup
of metallic particles should be kept away
from charger cavities. Always unplug the
charger from the power supply when there
is no battery pack in the cavity. Unplug
charger before attempting to clean.

DO NOT attempt to charge the battery
pack with any chargers other than the
ones in this manual. The charger and
battery pack are specifically designed
to work together.

These chargers are not intended
for any uses other than charging
designated BLACK +DECKER
rechargeable batteries. Any other uses
may result in risk of fire, electric shock
or electrocution.
Do not expose charger to rain or snow.
Pull by plug rather than cord when
disconnecting charger. This will reduce
risk of damage to electric plug and cord.
Make sure that cord is located so that it
will not be stepped on, tripped over, or
otherwise subjected to damage or stress.
Do not use an extension cord unless it is
absolutely necessary. Use of improper
extension cord could result in risk of fire,
electric shock, or electrocution.
An extension cord must have adequate

for safety. The smaller the gauge number
of the wire, the greater the capacity of the


extension to make up the total length, be
sure each individual extension contains at
least the minimum wire size.
Do not place any object on top of
charger or place the charger on
a soft surface that might block
the ventilation slots and result in
excessive internal heat. Place the
charger in a position away from any
heat source. The charger is ventilated
through slots in the top and the bottom of
the housing.
Do not mount charger on wall or
permanently affix charger to any
surface. The charger is intended to use
on a flat, stable surface (i.e., table top,
bench top).

Do not operate charger with damaged
cord or plug —
have them replaced
immediately.
Do not operate charger if it has
received a sharp blow, been dropped,
or otherwise damaged in any way.
Take it to an authorized service center.
Do not disassemble charger; take it
to an authorized service center when
service or repair is required. Incorrect
reassembly may result in a risk of electric
shock, electrocution or fire.

Disconnect the charger from the outlet
before attempting any cleaning.
This
will reduce the risk of electric shock.
Removing the battery pack will not reduce
this risk.
NEVER attempt to connect 2 chargers
together.
The charger is designed to operate on
standard household electrical power
(120 Volts). Do not attempt to use it on
any other voltage.
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTION
FOR BATTERY PACKS
WARNING:
For safe operation,
read this manual and manuals
originally supplied with tool
before using the charger.
The battery pack is not fully charged out of
the carton. Before using the battery pack and
charger, read the safety instructions below.
Then follow charging procedures outlined.
READ ALL INSTRUCTIONS

Do not incinerate the battery pack even
if it is severely damaged or is completely
worn out. The battery pack can explode
in a fire. Toxic fumes and materials are
created when battery packs are burned.

Do not charge or use battery in explosive
atmospheres, such as in the presence
of flammable liquids, gases or dust.
Inserting or removing the battery from the
charger may ignite the dust or fumes.

If battery contents come into contact
with the skin, immediately wash area
with mild soap and water. If battery liquid
gets into the eye, rinse water over the
open eye for 15 minutes or until irritation
ceases. If medical attention is needed, the
battery electrolyte for Lithium-Ion batteries
is composed of a mixture of liquid organic
carbonates and lithium salts.
Contents of opened battery cells may
cause respiratory irritation. Provide
fresh air. If symptoms persist, seek
medical attention.
WARNING:
Burn hazard. Battery
liquid may be flammable if exposed to
spark or flame.
Charge the battery packs only in
BLACK+DECKER chargers.

DO NOT splash or immerse in water or
other liquids. This may cause premature
cell failure.
 Do not store or use the tool and battery
pack in locations where the temperature
may reach or exceed 105°F (40˚C) (such as
outside sheds or metal buildings in summer).
WARNING: Never attempt to open
the battery pack for any reason. If battery
pack case is cracked or damaged, do not
insert into charger. Do not crush, drop or
damage battery pack. Do not use a
battery pack or charger that has received
a sharp blow, been dropped, run over or
damaged in any way (i.e., pierced with a
nail, hit with a hammer, stepped on).
Damaged battery packs should be
returned to service center for recycling.
WARNING: Fire hazard. Do not store
or carry battery so that metal objects can
contact exposed battery terminals. For
example, do not place battery in aprons,
pockets, tool boxes, product kit boxes,
drawers, etc., with loose nails, screws,
keys, etc. Transporting batteries can
possibly cause fires if the battery terminals
inadvertently come in contact with
conductive materials such as keys, coins,
hand tools and the like. The US
Department of Transportation Hazardous
Material Regulations (HMR) actually
prohibit transporting batteries in commerce
or on airplanes (i.e., packed in suitcases
and carry-on luggage) UNLESS they are
properly protected from short circuits. So
when transporting individual batteries,
make sure that the battery terminals are
protected and well insulated from materials
that could contact them and cause a short
circuit. NOTE: Lithium-Ion batteries should
not be put in checked baggage.
STORAGE RECOMMENDATIONS

The best storage place is one that is
cool and dry away from direct sunlight and
excess heat or cold.
2. Long storage will not harm the battery
pack or charger.
IMPORTANT CHARGING NOTES

be obtained if the battery pack is charged


battery pack in an air temperature below

This is important and will prevent serious
damage to the battery pack.
2. The charger and battery pack may become
warm to touch while charging. This is a normal
condition, and does not indicate a problem. To
facilitate the cooling of the battery pack after
use, avoid placing the charger or battery pack
in a warm environment such as in a metal
shed, or an uninsulated trailer.
3.
If the battery pack does not charge properly:

plugging in a lamp or other appliance.

connected to a light switch which turns
power off when you turn out the lights.
c. Move charger and battery pack to a
location where the surrounding air


d. If charging problems persist, take
the tool, battery pack and charger to
your local service center.
4. The battery pack should be recharged
when it fails to produce sufficient power on
jobs which were easily done previously.
DO NOT CONTINUE to use under these
conditions. Follow the charging procedure.
You may also charge a partially used pack
whenever you desire with no adverse
affect on the battery pack.

such as, but not limited to, steel wool,
aluminum foil, or any buildup of metallic
particles should be kept away from charger
cavities. Always unplug the charger from
the power supply when there is no battery
pack in the cavity. Unplug charger before
attempting to clean.

water or any other liquid.
WARNING: Shock hazard. Do not
allow any liquid to get inside charger.Never
attempt to open the battery pack for any
reason. If the plastic housing of the
battery pack breaks or cracks, return to
a service center for recycling.
FUNCTIONAL DESCRIPTION
Figure A


3. Shoe
4. Blade clamp release lever





CHARGING PROCEDURE
 chargers are designed to
charge 
hours depending on the pack being charged.

outlet before inserting the battery pack.
2. Insert the battery pack into the charger
as shown in figure B.
3. The green LED will flash indicating that
the battery is being charged.
4.
The completion of charge is indicated by
the green LED remaining on continuously.
The pack is fully charged and may be used
at this time or left on the charger.
LEAVING THE BATTERY IN
THE CHARGER
The charger and battery pack can be left
connected with the green LED glowing
indefinitely. The charger will keep the
battery pack fresh and fully charged.
INSTALLATION AND REMOVAL OF
THE BATTERY PACK
TO INSTALL BATTERY PACK: Insert
battery pack into the tool until an audible
Figure C). Make sure
Description Catalog #
These products use the batteries and chargers listed in the chart below.
20v Max** Lithium-Ion Battery: LBXR20
20v Max** Type 1 22wh Lithium-Ion Battery: LB20
Lithium 2 Amp Fast Charger: L2AFC
Lithium 2 Amp Fast Charger: L2AFCBST
20v Max** Lithium-Ion Battery Charger: LCS20
20v Max** Lithium-Ion Battery Charger: LCS201
20v Max** Lithium-Ion Battery Charger: LCS1620
battery pack is fully seated and fully
latched into position.
TO REMOVE BATTERY PACK: Depress
the battery release button as shown in figure
D and pull battery pack out of the tool.
OPERATING INSTRUCTIONS
WARNING: Always use proper eye
protection that conforms to ANSI
Z87.1(CAN/CSA Z94.3) while operating
this power tool.
NOTE: Before cutting any type of
material, be sure it is firmly anchored or
clamped to prevent slipping.

to be cut.

maximum speed before starting the cut.

while cutting as shown in figure D.
Whenever possible, the saw shoe must
be held firmly against the material being
cut. This will prevent the saw from
jumping or vibrating and will minimize
blade breakage.
TRIGGER SWITCH

feature to prevent unintentional operation.




Releasing the trigger turns the motor OFF.
NOTE: This tool has no provision to lock
the switch in the ON position, and should
never be locked in the ON position by any
other means.
BLADE CLAMP RELEASE LEVER
WARNING: Cut hazard. Turn off
and remove battery from tool before
making any adjustments or removing or
installing attachments or accessories.
WARNING: Cut hazard. Blade
breakage may occur if the blade does not
extend past the shoe and the workpiece
during the cut. Increased risk of personal
injury, as well as damage to the shoe and
workpiece may result.
TO INSTALL BLADE INTO SAW:
 
full open position as shown in figure F.
2. Insert blade shank from the front.
 
to make sure blade is clamped securely.
NOTE: BLADE CAN BE INSTALLED
UPSIDE-DOWN TO ASSIST IN FLUSH-
TO CUTTING.
TO REMOVE BLADE FROM SAW:
WARNING: Burn hazard. Do not
touch the the blade immediately after use.
Contact with the blade may result in
personal injury.
 
full open position.
2. Remove blade.
FLUSH CUTTING (FIGURE G)

saw motor housing and pivoting shoe
permit close cutting to floors, corners and
other difficult areas.

insert the blade shaft into the blade clamp
with the teeth of the blade facing up.

close to the work surface as possible.
WOOD CUTTING (FIGURE H)

the work piece is firmly anchored or
clamped to prevent slipping.

to be cut.

pressure.

while cutting. Whenever possible, the
shoe must be held firmly against the
material being cut. This will prevent
the saw from jumping or vibrating and
minimize blade breakage.
METAL CUTTING (FIGURE I)



to clamp wood to the underside of the
sheet. This will ensure a clean cut without
excess vibration or tearing of metal.

reduces blade life and causes costly
blade breakage.
NOTE: You should spread a thin
film of oil or other coolant along the
line ahead of the saw cut for easier
operation and longer blade life.
For cutting aluminum, kerosene is
preferred.
POCKET CUTTING - WOOD ONLY
(FIGURE J)

Measure the surface area to be cut and
mark clearly with a pencil, chalk or scriber.

blade clamp securely.

Tip the saw backward until the bottom edge
of the shoe is resting on the work surface.

attain maximum speed.

deliberate upward swing with the handle
of the saw.

Always be sure blade is completely
through material before continuing with
pocket cut.
NOTE: IN AREAS WHERE BLADE
VISIBILITY IS LIMITED, USE THE EDGE
OF THE SHOE AS A GUIDE.
PROJECT TIPS

cleaner, faster and put less strain on the
motor while cutting.

shoe is firmly against the workpiece.
This will improve operator control and
minimize vibration.

These utilize a carbon steel back welded
to high speed steel teeth making the blade
more flexible and less prone to breaking.
MAINTENANCE
WARNING: REMOVE BATTERY
FROM SAW WHEN PERFORMING ANY
CLEANING OR OTHER MAINTENANCE.
WHEN SERVICING USE ONLY
IDENTICAL REPLACEMENT PARTS.

parts. Most plastics are susceptible to
various types of commercial solvents and
may be damaged by their use. Use only
mild soap and damp cloth to clean the tool.

immerse any part of the tool into a liquid.

fiberglass boats, sports cars, drywall
etc.,they are subject to accelerated wear
and possible premature failure, as the
fiberglass chips and grindings and drywall
dust are highly abrasive to bearings,
brushes, commutator, etc. During any
use on fiberglass or drywall it is extremely
important that the tool be cleaned
frequently by blowing with an air jet.
LUBRICATION
Your tool was properly lubricated before
leaving the factory. Once every year take
or send your tool to a

service center, or authorized service
station, for a complete cleaning, inspection
and lubrication. Tools “out of service” for
long periods should be relubricated before
being put back to work.
ACCESSORIES
Your reciprocating saw will accept up to a

blade suitable for your project. Longer blades
are more likely to be bent or damaged during
use. During operation, some longer blades
may vibrate or shake if the saw is not kept in
contact with the workpiece.
WARNING: S
ince accessories, other
than those offered by

,
have not been tested with this product, use of
such accessories with this tool could be
hazardous. To reduce the risk of injury, only

recommended
accessories should be used with this product.
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION
  
installation.
 
charging requirements.
  
charger until LED illuminates.
 
working outlet. Refer to

for more details.
 
too hot or too cold. pack to a surrounding air
temperature of above



  
maximum thermal limit. down.
To 
maximize the life of the allow to charge.
battery pack it is designed
to shutoff abruptly when
the charge is depleted.
For assistance with your product, visit our website www.blackanddecker.com for the location
of the service center nearest you or call the



A complete line of accessories is available
from your

Factory Service


Authorized

Site www.blackanddecker.com for a catalog
or for the name of your nearest supplier.
ACCESSORIES
WARNING:
The use of any accessory
not recommended for use with this tool
could be hazardous.
Recommended accessories for use with
your tool are available from your local
dealer or authorized service center. If you
need assistance regarding accessories,
please call: 1-800-544-6986.
THE RBRC™ SEAL






been paid by . In some

batteries in the trash or municipal solid waste

environmentally conscious alternative.


and other battery
users, has established programs in the


Help protect our environment and
conserve natural resources by returning
the tool to an authorized

service center for recycling. You may also
contact your local recycling center for
information on where to drop off the spent
battery, or call 1-800-8-BATTERY.



Operation is subject to the following two


must accept any interference received,
including interference that may cause
undesired operation.
NOTE:
This equipment has been tested and


Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio or television reception, which can
be determined by turning the equipment
off and on, the user is encouraged to try to
correct the interference by one or more of the
following measures:


equipment and the receiver.

a circuit different from that to which the
receiver is connected.


SERVICE INFORMATION
All 
staffed with trained personnel to provide
customers with efficient and reliable power
tool service. Whether you need technical
advice, repair, or genuine factory replacement
parts, contact the  location
nearest you. To find your local service
location, call: 1-800-544-6986 or visit www.
blackanddecker.com
LIMITED TWO-YEAR
HOME USE WARRANTY

product for two years against any defects
in material or workmanship. The defective
product will be replaced or repaired at no
charge in either of two ways. The first, which
will result in exchanges only, is to return
the product to the retailer from whom it


made within the time period of the retailer’s


required. Please check with the retailer for
their specific return policy regarding returns
that are beyond the time set for exchanges.
The second option is to take or send the


repair or replacement at our option. Proof of
purchase may be required.This warranty does
not apply to accessories. This warranty gives
you specific legal rights and you may have
other rights which vary from state to state or
province to province. Should you have any
questions, contact the manager of your nearest

product is not intended for commercial use.
FREE WARNING LABEL REPLACEMENT:
If your warning labels become illegible or
are missing, call 1-800-544-6986 for a free
replacement.
LATIN AMERICA: This warranty does not
apply to products sold in Latin America. For
products sold in Latin America, check country
specific warranty information contained in the
packaging, call the local company or see the
website for warranty information.
Imported by:



  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

Black & Decker BDCR20C User manual

Category
Power tools
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI