Craftsman CMXEVBE17585 User manual

Brand: Craftsman

Model: CMXEVBE17585

Category: Vacuum cleaners

Type: User manual

Part No. SP7088 Printed in Mexico

INSTRUCTION MANUAL | GUIDE D’UTILISATION | MANUAL DE INSTRUCCIONES

IF YOU HAVE QUESTIONS OR COMMENTS, CONTACT US.

POUR TOUTE QUESTION OU TOUT COMMENTAIRE, NOUS CONTACTER.

SI TIENE DUDAS O COMENTARIOS, CONTÁCTENOS.

5 GALLON (18 LITERS) ASH VACUUM

ASPIRATEUR POUR RAMASSER DES CENDRES

DE 18 LITRES (5 GALLONS)

ASPIRADORA DE CENIZA DE 18 LITROS (5 GALONES)

CMXEVBE175850

1-888-331-4569 WWW.CRAFTSMAN.COM

SP7088-2 CMXEVBE175850.indb 1 10/24/19 11:59 AM

DANGER: Indicates a hazardous situation which, if not avoided, will result in death or serious

injury.

WARNING: Indicates a hazardous situation which, if not avoided, could result in death or serious

injury.

CAUTION: Indicates a hazardous situation which, if not avoided, may result in minor or moderate

injury.

(Used without word) Indicates a safety related message.

NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in property damage.

Definitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk

of personal injury or property damage.

Components

Fig. A

1 Carry Handle

2 Cord Wrap Area

3 Hose Wrap Area

4 ON/OFF Switch

5 Powerhead Assembly

6 Vacuum Inlet Port

7 Drum

8 Drum Latches (2)

9 Power Cord

10 Accessory Storage Slots (2)

If you have any questions or comments about this or

any product, call CRAFTSMAN toll free at:

1-888-331-4569.

WARNING: Read all safety

warnings and all instructions. Failure to follow the

warnings and instructions may result in electric shock,

fire and/or serious injury.

WARNING: Never modify the

product or any part of it. Damage or personal injury

could result.

WARNING: To reduce the risk of

injury, read the instruction manual.

SP7088-2 CMXEVBE175850.indb 2 10/24/19 11:59 AM

IMPORTANT SAFETY INSTRUCTIONS

• Read and understand this manual and all labels on the

Vacuum before operating.

• Use only as described in this manual.

• Do not pick up anything that is burning or smoking, like

cigarettes, matches or hot, glowing, or burning embers.

Pick up cold ash only. Be aware that ash/embers can be hot

for days after use.

• Use caution when vacuuming materials that appear to have

cooled, but may actually be hot inside. First check for hot

spots by raking through the ashes/coals. Air flow created

during vacuuming may cause hot ash to re-ignite. As you

vacuum, constantly check the nozzle, hose, drum, and motor

for excessive temperatures. If you notice an increase in

temperature, turn off the vacuum immediately. Unplug the

vacuum and remove the vacuumed material from the drum.

• The drum must be emptied and cleaned after each use,

and before picking up other household debris.

• Allow the vacuum to cool before storage, especially enclosed

storage.

• Do not use paper dust bags.

• To reduce the risk of damage from accidental hot ember

pickup, do not place the vacuum on surfaces susceptible

to heat damage, such as carpeting, vinyl flooring, or wood

surfaces.

• Do not leave vacuum running while unattended - you

may fail to notice important signs indicating abnormal

operation such as loss of suction, or abnormal motor noises.

Immediately stop using vacuum if you notice these signs.

• Do not leave vacuum when plugged in. Unplug from

outlet when not in use and before servicing.

• Sparks inside the motor can ignite flammable vapors

or dust. To reduce the risk of fire or explosion, do not

use near combustible liquids, gases, or dusts, such as

gasoline or other fuels, lighter fluid, cleaners, oil-based

paints, natural gas, coal dust, magnesium dust, grain

dust, aluminum dust, or gun powder.

• To reduce the risk of inhaling toxic vapors, do not

vacuum or use near toxic or hazardous materials.

• To reduce the risk of electric shock, do not expose

to rain or allow liquid to enter motor compartment.

Store indoors.

• This Ash Vacuum is not intended for use by

persons (including children) with reduced physical,

sensory, or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person

responsible for their safety.

• Only use extension cords that are intended

for outdoor use. Use only three-wire outdoor

extension cords that have three-prong grounding plugs

and grounding receptacles that accept the vacuum’s

plug. Extension cords in poor condition or too small in

wire size can pose fire and shock hazards. To reduce

the risk of these hazards, be sure the cord is in good

condition and that liquid does not contact the

connection. Do not use an extension cord with

conductors smaller than 1,3 mm

(16 AWG) in size.

• Do not use with damaged cord, plug, or other parts.

If your Vacuum is not working as it should, has

missing parts, has been dropped, damaged, left

outdoors, or dropped into water, call customer service at

1-888-331-4569 (Mexico 001-881-331-4569).

• Connect only to a properly-grounded outlet.

See grounding instructions

• Do not put any object into ventilation openings. Do not

vacuum with any ventilation openings blocked; keep

free of dust, lint, hair or anything that may reduce air

flow.

• Keep hair, loose clothing, fingers, and all parts of body

away from openings and moving parts.

• To reduce the risk of falls, use extra care when cleaning

on stairs.

• To reduce the risk of personal injury or damage to

Vacuum, use only CRAFTSMAN recommended

accessories.

• To reduce the risk of eye injury, wear safety eyewear.

The operation of any utility vacuum can result in foreign

objects being blown into the eyes, which can result in

severe eye damage.

• Do not allow to be used as a toy. Close attention is

necessary when used by or near children.

• Turn off Vac before unplugging.

• To reduce the risk of injury from accidental starting,

unplug power cord before changing or cleaning filter.

• Do not unplug by pulling on cord. To unplug, grasp the

plug, not the cord.

• Do not pull or carry by cord, use cord as handle, close a

door on cord, or pull cord around sharp edges or corners.

Keep cord away from heated surfaces.

WARNING:

To reduce the risk of fire, electric shock, or injury:

When using this Vacuum, always follow basic safety

precautions including the following:

This vacuum is intended to pick up COLD ash from

fireplaces, grills, ovens, ashtrays, etc. Read and understand

this manual and all labels on this Ash Vacuum before

operating.

SP7088-2 CMXEVBE175850.indb 3 10/24/19 11:59 AM

CAUTION:

• To reduce the risk of hearing damage, wear ear

protectors when using for an extended time or

in a noisy area.

• For dusty operations, wear dust mask.

• Static shocks are common when the relative

humidity of the air is low. Vacuuming fine

debris with your Vac can deposit static charge on

the hose or Vacuum. To reduce the frequency of

static shocks in your home or when using

this Vacuum, add moisture to the air with a

humidifier.

SAVE THESE INSTRUCTIONS

WARNING:

• For your own safety, read and understand Instruction

Manual.

• Do not run unattended.

• Do not pick up hot ashes, coals, flammable,

combustible / self-igniting, toxic, or other hazardous

materials.

• Do not use around explosive liquids or vapors.

• To reduce the risk of electric shock, do not use on wet

surfaces.

• Do not expose to rain. Store indoors.

• This is a dry vacuum only; NEVER vacuum liquids

with this product.

Observe the following warnings that appear on the

Lighted Nozzle.

WARNING:

• Keep batteries out of reach of small children. Consult

a physician immediately if a battery is swallowed;

severe burning or injury may occur.

• Battery contains Perchlorate Material - Special

handling may apply.

See www.dtsc.ca.gov/hazardouswaste/perchlorate.

Observe the following warnings that appear on the Vacuum.

WARNING:

Risk of fire and Heat Damage.

This vacuum is intended to pick up COLD ash from

fireplaces, grills, ovens, ash-trays, etc. Do not pick up

hot, glowing, or burning ash/embers. Pick up cold ash

only. Be aware that ash/embers can be hot for days after

use. To reduce the risk of damage from accidental hot

ember pickup, do not place the vacuum on surfaces

susceptible to heat damage such as carpeting, vinyl

flooring, or wood surfaces. Empty drum after each use.

Allow to cool before storing, especially in enclosed

spaces. Do not use dust collection bags.

FREE WARNING LABEL REPLACEMENT: If your warning

labels become illegible or are missing, call 1-888-331-4569

for a free replacement.

SP7088-2 CMXEVBE175850.indb 4 10/24/19 11:59 AM

This Ash Vacuum is intended for household use. It may be

used for vacuuming of dry debris, including cold ash from

fireplaces, grills, ovens, ash-trays, etc. It should not be used

to pick up liquids.

Read this Instruction Manual to familiarize yourself with

the product features and to understand the specific usage

of your new vacuum.

INTRODUCTION

Section Page

Important Safety Instructions.......................2-4

Introduction .......................................5

Grounding Instructions..............................6

Carton Contents ....................................7

Installation .....................................8-11

Powerhead Assembly .............................8

Powerhead Disassembly...........................8

Insert Locking Hose ...............................9

Hose Assembly...................................9

LED Lighted Nozzle Usage ........................10

LED Lighted Nozzle Battery Replacement............10

Power Cord Storage..............................11

Accessory Storage ...............................11

Hose Assembly Storage...........................11

Operation .....................................12-13

Motor / Electrical ................................12

Emptying the Drum..............................13

Maintenance...................................14-15

HEPA Media Filter ...............................14

Filter Removal and Replacement...................14

Filter Removal ..................................14

Filter Installation ................................14

Cleaning a Dry Cartridge Filter.....................15

Cleaning and Disinfecting the Ash Vacuum..........15

Cord Maintenance & Storage ......................15

Ash Vacuum Storage .............................15

Service / Repair Parts...............................16

Warranty .........................................17

TABLE OF CONTENTS

SP7088-2 CMXEVBE175850.indb 5 10/24/19 11:59 AM

This Vacuum must be Grounded. If it should

malfunction or break down, Grounding provides a path

of least resistance for Electric Current to reduce the risk of

Electric Shock. This Vacuum is equipped with a Cord

having an Equipment-grounding Conductor and

Grounding Plug. The Plug must be inserted into an

appropriate Outlet that is properly installed and Grounded

in accordance with all Local Codes and Ordinances.

Properly

Grounded

Outlet

Grounding

Prong

3-Prong

Plug

GROUNDING INSTRUCTIONS

Fig. B

This Vacuum is for use on a nominal 120 Volt Circuit, and

has a Grounded Plug that looks like the Plug shown.

A Temporary Adapter that looks like the Adapter shown

may be used to connect this Plug to a 2-Pole Receptacle,

as shown. If a properly Grounded Outlet is not

available, the Temporary Adapter should be used only

until a properly Grounded Outlet can be installed by a

Qualified Electrician.

The Green Colored Rigid Ear, Lug or the like extending

from the Adapter must be connected to a Permanent

Ground such as a properly Grounded Outlet Box Cover.

Whenever the Adapter is used, it must be held in place

by a Metal Screw.

NOTE: In Canada, the Use of a Temporary Adapter is Not

Permitted by the Canadian Electrical Code.

Make sure this is a

metal screw connected

to a known ground

Green

Grounding Lug

Metal

Screw

3-Prong Plug

Adapter

2-Prong Outlet

Fig. C

WARNING:

Improper connection of the equipment grounding

conductor can result in a risk of electric shock. Check

with a qualified electrician or service person if you are

in doubt as to whether the outlet is properly grounded.

Do not modify the plug provided with the appliance -

if it will not fit the outlet, have a proper outlet installed

by a qualified electrician.

SP7088-2 CMXEVBE175850.indb 6 10/24/19 11:59 AM

Key Description Qty.

A Ash Vacuum (5 Gallon/18 Liters) 1

B Metal Cover 1

C HEPA Media Filter 1

D Filter Screen 1

E Extension Nozzle 1

F Wand Nozzle 1

G Locking Hose (metal lined)

with LED Lighted Nozzle 1

H Instruction Manual 1

Some items may come preassembled.

If they are not present in the carton, check the vacuum

powerhead to see if they are preassembled.

Remove entire contents of carton. Check each item against

the Carton Contents List.

If any parts are damaged or missing, return the product

to the retailer from which is was purchased for exchange.

CARTON CONTENTS (Fig. D)

Fig. D

SP7088-2 CMXEVBE175850.indb 7 10/24/19 11:59 AM

Powerhead Assembly (Figs. E & F)

1. Line up front of Powerhead Assembly with Vacuum

Port located on the front of the Drum, as shown.

2. Place Powerhead Assembly on top of Drum.

3. Be sure Powerhead Assembly completely covers the

top of the Drum so leakage does not occur.

4. Rotate the Latches on each side of the Drum,

positioning the Latch Hooks over the Lip of the

Powerhead Assembly.

5. Snap down the bottom edge of the Latches to secure

the Powerhead Assembly to the Drum.

INSTALLATION

Fig. E

Powerhead Disassembly (Fig. G)

Fig. F

Vacuum

Port

Drum

Powerhead

Assembly

Lip

ROTATE

LATCH

SNAP

DOWN

LATCH

Powerhead

Assembly

Latch

Fig. G

1. Grasp the Drum Latches on both the right and left side

of the Vacuum.

2. Slowly pull the bottom of the Latches up and away

from the Drum.

3. The top of the Latches will then be free of the

Powerhead Assembly.

4. Lift the Powerhead Assembly from the Drum and place

it on a dry surface.

WARNING:

For your own safety, never connect plug to

power source outlet until all assembly steps

are complete and you have read and under-

stood the safety and operation instructions.

Do not operate vacuum with any parts damaged or

missing.

SNAP

DOWN

LATCH

Latches

ROTATE

LATCH

Powerhead Assembly

Lip

SP7088-2 CMXEVBE175850.indb 8 10/24/19 11:59 AM

Insert Locking Hose (Fig. H)

NOTE: Use ONLY the Metal Lined Hose and Metal

Accessories provided with this Ash Vacuum.

1. Align Hose Tabs with Vacuum Inlet and insert the

Locking End of the Hose into the Vacuum Inlet of the

Vacuum Drum, as shown.

2. Rotate the Hose clockwise to lock into place.

3. To remove the Hose from the Vacuum, rotate the

Locking Hose Counterclockwise and pull the Hose out

of the Vacuum Inlet.

Fig. H

Inlet

Locking Hose

(Metal Lined)

with LED Light

ROTATE HOSE

CLOCKWISE

TO LOCK

Hose Locking End

Hose Assembly (Figs. I & J)

1. Slide the Round End of the Extension Nozzle into the

smaller Tapered End of the Wand Nozzle.

Fig. I

Wand

Nozzle

Extension

Nozzle

2. Loosen the Two LED Assembly Screws, located at the

bottom of the LED Lighted Nozzle.

3 Slide the Wand Nozzle through the LED Assembly and

into the Rubber Hose Fitting.

4. Retighten the Two LED Assembly Screws to secure the

LED Assembly to the Hose Assembly.

Fig. J

LED Lighted

Nozzle

Screws (2)

Wand Nozzle

SP7088-2 CMXEVBE175850.indb 9 10/24/19 11:59 AM

LED Lighted Nozzle Usage (Fig. K)

1. Press Button to activate LED light while Vacuuming.

2. Slide the Switch Forward to Lock the LED Light in the

ON position.

3. Slide the Switch Back to the OFF position after use.

Fig. K

LED Lighted Nozzle Battery Replacement

(Fig. L)

1. To access Batteries, remove and retain the Battery

Access Panel Screw.

2. Remove and retain the Four Screws from the LED

Assembly, releasing the Switch Button Module.

3. The Two Batteries are located under the Switch

Button module. Dispose Batteries in the proper waste

disposal container.

4. The LED Light uses Two CR2016 Lithium Batteries that

are replaceable.

5. Reposition the Switch Button Module over the Battery

Compartment. Install the previously removed Four

Screws into the Switch Button Module to secure.

6. Reposition the Battery Access Panel over the Switch

Button Module. Install the previously removed Screw

into the Battery Access Panel to secure.

WARNING:

Keep batteries out of reach of small children. Consult

a physician immediately if a battery is swallowed.

Severe burning or injury may occur.

Battery contains Perchlorate Material - Special handling

may apply.

See www.dtsc.ca.gov/hazardouswaste/perchlorate.

LED Button

LED

Assembly

Fig. L

Switch

Button

Module

CR2016

Lithium

Batteries

(2)

Battery

Access

Panel

Screw (1)

Screws (4)

LED

Assembly

SP7088-2 CMXEVBE175850.indb 10 10/24/19 11:59 AM

Hose Assembly Storage (Fig. O)

Wrap the Hose around the top of the cooled Powerhead

Assembly, positioning the Hose under the Carry Handle/

Hose Wrap Area.

CAUTION:

Do not operate vacuum while the hose or

accessories are stored on the wet/dry vacuum’s

powerhead assembly.

Fig. O

WARNING:

Do not put any object into ventilation openings.

Do not vacuum with any ventilation openings blocked;

keep free of dust, lint, hair or anything that may reduce

air flow.

Hose Wrap

Area

Hose

Accessory Storage (Fig. N)

The Accessories can be stored on the rear of the Powerhead

Assembly by placing each Accessory into the Powerhead

Assembly Slots.

Fig. N

Powerhead

Assembly

Slots (2)

Accessories

Power Cord Storage (Fig. M)

The Power Cord should be wrapped around the Powerhead

Assembly Carry Handle.

Snap the Cord Clip onto the Power Cord, to secure in place.

Fig. M

Power

Cord

Powerhead

Assembly

Cord

Storage

Cord Clip

WARNING:

To prevent serious injury from electrical shock,

stop vacuum use immediately if the power cord is

damaged. Take the vacuum to a qualified service dealer

for inspection and possible repair.

SP7088-2 CMXEVBE175850.indb 11 10/24/19 11:59 AM

WARNING:

To reduce the risk of fire, explosion,

or damage to Vacuum:

OPERATION

• Do not leave Vacuum running while

unattended - you may fail to notice import-

ant signs indicating abnormal operation such

as loss of suction, debris exiting the exhaust,

or abnormal motor noises. Immediately stop

using Vacuum if you notice these signs.

• Do not leave Vacuum plugged in when not in

use.

• Sparks inside the motor can ignite airborne

flammables. Do not operate Vacuum near

flammable liquids or in areas with flammable gases,

vapors, or explosive / airborne dust. Flammable

liquids, gases, and vapors include: lighter fluid,

solvent-type cleaners, oil-based paints,

gasoline, alcohol, and aerosol sprays. Explosive

dusts include: coal, magnesium, aluminum, grain,

and gun powder.

• Do not vacuum up explosive dusts, flammable

liquids, or hot ashes.

• The drum must be emptied and cleaned after

each use, and before picking up other household

debris.

Motor / Electrical (Fig. P)

This Ash Vacuum is rated for use with 120 Volt 60 Hz

supply. The Vacuum is equipped with a Thermal Protection

Cutoff Switch which will remove Power from the Vacuum

Motor if excessively high Operating Temperatures are

detected. This condition may arise as the result of a

blocked Vacuum passage, or clogged Filter. If a Thermal

trip takes place, immediately Toggle the Vacuum’s

Switch to OFF, Unplug the Unit and inspect for an airflow

blockage in the Hose and verify the condition of the Filters

(see Maintenance). Clean or replace the Filters as required.

The Vacuum will require several minutes to cool down to

a safe operating temperature. When this temperature is

attained, the Thermal Switch will automatically Reset and

the Vacuum will be able to be used in the normal manner.

After you Plug the Power Cord into the Outlet, turn the Unit

on by pushing the Switch from position “O” to position “l”.

The symbols used on the Switch Actuator are International

“On & Off” Symbols:

OFF

Fig. P

"OFF"

"ON"

WARNING:

To reduce the risk of electric shock or injury:

• Do not expose to rain or allow liquid to enter

motor compartment. Store indoors.

• Do not handle plug, switch, or Vacuum with wet

hands.

• Unplug Vacuum before servicing. If your Vacuum

is not working as it should, has missing parts,

has been dropped, damaged, left outdoors, or

dropped into water, call customer service at

1-888-331-4569 (Mexico 001-881-331-4569).

• When using an extension cord, use only

outdoor-rated cords that are in good condition.

Do not allow the connection to come into contact

with liquid.

CAUTION:

To reduce the risk of hearing damage, wear ear

protectors when using the Vacuum for an extended

time or in a noisy area.

SP7088-2 CMXEVBE175850.indb 12 10/24/19 11:59 AM

NOTE: Do not store the Vacuum immediately after Ash

removal or other use in a confined area or enclosed space.

Allow the Powerhead Assembly to cool and remove Ash

from Drum before storage.

1. Grasp the Drum Latches on both sides of the

Powerhead Assembly.

2. Slowly Pull Up on the Drum Latches, away from the

Drum.

3. The top of the Latches will be free of the Powerhead

Assembly.

Emptying the Vacuum Drum (Figs. Q & R)

WARNING:

To reduce the risk of injury from accidental starting,

unplug power cord before emptying the vacuum

drum.

Fig. Q

Drum

PULL

LATCH

UP AND

AWAY

ROTATE

LATCH

DOWN

ROTA

LATCH

DOWN

PULL

LATCH

UP AND

AWAY

Latch

NOTE: Be sure the Ash is cool prior to dumping the

contents into the proper waste disposal container.

4. Lift up on the Powerhead Assembly and set it on a

clean dry area.

5. Empty the Drum into the proper waste disposal

container.

6. Inspect the Filter per the “Filter Removal and

Installation” Section of this Manual.

7. Reassemble the Powerhead Assembly to the Drum.

Drum

Cold Ash

Fig. R

CAUTION:

To reduce the risk of hearing damage, wear ear

protectors when using the Vacuum for an extended

time or in a noisy area.

SP7088-2 CMXEVBE175850.indb 13 10/24/19 11:59 AM

MAINTENANCE

WARNING:

To reduce the risk of injury from accidental starting,

unplug power cord before changing or cleaning filter.

HEPA Media Filter

Your HEPA Media Filter should be cleaned often to

maintain peak Vacuum performance.

IMPORTANT: It is very important that the screen filter is

installed prior to use.

NOTE: The HEPA Media Filter is made of high quality

material designed to stop dust and smaller particles.

Handle the HEPA Media Filter carefully when

removing to clean or installing a new HEPA Media

Filter. Creases in the HEPA Media Filter pleats may

occur from installation but creases will not affect the

performance of the HEPA Media Filter.

Filter Removal and Installation

Filter Removal (Fig. S):

1. Rotate the Filter Screen / HEPA Media Filter

Counter-Clockwise.

2. Remove the HEPA Media Filter from the Filter Screen.

NOTE: The Filter Screen should be cleaned with a brush.

3. Check the Motor Inlet Filter, clean or replace,

if necessary.

Fig. S

HEPA

Media Filter

Filter

Screen

Raised Lip

Filter Installation (Fig. T):

1. Replace Motor Inlet Filter.

2. Replace the HEPA Media Filter into the Filter Screen.

NOTE: Be sure to orient the HEPA Media Filter and the Filter

Screen in the correct position, as shown. The Filter Screen

has a raised lip on the inside of the Screen to hold it in place.

3. Rotate the Filter Screen/HEPA Media Filter Clockwise

onto the Powerhead Metal Cover.

Fig. T

Powerhead

Assembly

Filter

Screen

HEPA Media

Filter

Motor Inlet

Filter

Metal

Cover

SP7088-2 CMXEVBE175850.indb 14 10/24/19 11:59 AM

Cleaning A Dry Cartridge Filter

NOTE: For best cleaning results due to accumulated dust,

clean the Filter in an open area. Cleaning SHOULD be done

outdoors and not in the living quarters.

1. Light cleaning of some dry debris from the Filter can

be accomplished without removing the Filter from the

Vacuum. Simply slap your hand on top of the handle

while the Vacuum is turned off.

2. Remove Filter from Vacuum. Gently tap the Filter against

the inside wall of your Drum, or against the floor, and the

debris will loosen and fall.

Cleaning and Disinfecting the

Ash Vacuum

To keep your Vacuum looking its best, clean the outside with

a cloth dampened with warm water and mild soap.

To clean the Drum:

1. Dump debris out.

2. Wash the Drum thoroughly with warm water and mild

soap.

3. Wipe out with dry cloth.

Cord Maintenance & Storage

When vacuuming is complete, unplug the Power Cord and

wrap it around the Powerhead Handle. Accessories can be

stored on the rear of the Powerhead Assembly.

WARNING:

To assure product SAFETY and RELIABILITY, any other

maintenance, repairs and adjustments should be

performed by Authorized Service Centers, always

using CRAFTSMAN replacement parts.

Ash Vacuum Storage

Before storing your Vacuum, the Drum should be emptied

and cleaned. The Power Cord should be wrapped around the

Carry Handle. Positioning the Hose under the Carry Handle.

Accessories should be kept in the same area as the Vacuum

so they can be readily available. The Vacuum should be

stored indoors.

WARNING:

To prevent serious injury from electrical shock,

stop vacuum use immediately if the power cord is

damaged. Take the vacuum to a qualified service

dealer for inspection and possible repair.

SP7088-2 CMXEVBE175850.indb 15 10/24/19 11:59 AM

SERVICE / REPAIR PARTS

5 Gallon (18 Liter) Ash Vacuum

Model Number CMXEVBE175850

Electrical Ratings: 120 V~ 7.6 A 60 Hz

Always order by Part Number - Not by Key Number

WARNING: To reduce the risk of injury, unplug power cord before servicing the Wet/Dry Vacuum.

WARNING: All disassembly and repairs should be performed by qualified personnel.

Key

No. Part No. Description

1 836247-3 Handle, Carry

2 836248 Switch, Toggle

3 836265 Power Cord

4 836506 Drum Assembly

(Includes Drum, Drum Inlet,

Drum Latches, Carton & Label)

5 836257 Metal Cover

6 CMXZVBE38740 HEPA Media Filter

w/Motor Inlet Filter

Key

No. Part No. Description

7 836270 Metal Filter Screen

8 836276 Metal Extension Nozzle

9 836275 Metal Wand Nozzle

10 836277 Locking Hose

(Metal Lined)

11 836279 LED Lighted Nozzle Assembly

12 SP7088 Instruction Manual

SP7088-2 CMXEVBE175850.indb 16 10/24/19 11:59 AM

CRAFTSMAN

LIMITED WARRANTY – 3 YEARS

This limited warranty is provided by Emerson Tool Company, a division of Emerson Electric Co., (“We” or “Our” or “Us”) to

the original consumer owner (“Customer” or “You” or “Your”) of the CRAFTSMAN product with which this limited warranty

is provided (the “CRAFTSMAN Product”).

What is Covered

We warrant to You that your CRAFTSMAN Product will be free from defects in materials and workmanship when used

under normal conditions in accordance with the terms of the Instruction Manual provided to You with the CRAFTSMAN

Product, subject to the exclusions described below, for a period of three years commencing on the date of purchase by

You (the “Warranty Period”). This limited warranty terminates if the original purchaser transfers the CRAFTSMAN Product

to any other person or entity.

What is not Covered

This limited warranty does not extend to and expressly excludes:

• Normal wear and tear and/or replacement attachments or accessories, including, without limitation, power cords,

hoses, filters, and other attachments or accessories that may be offered for sale by Us for use with the CRAFTSMAN

Product.

• Damage or burnout of the CRAFTSMAN Product motor resulting from failure to clear a blockage occurring during the

normal course of use.

• Loss or damage to the CRAFTSMAN Product resulting from conditions beyond Our control including without

limitation, misuse, accident, abuse, neglect, negligence (other than Our’s), overuse beyond intended capacity as set

forth in the Instruction Manual, or modifications or alterations made by anyone other than Us.

• Loss or damage to the CRAFTSMAN Product resulting from failure to use the CRAFTSMAN Product in accordance with

the written instructions, guidelines, and terms and conditions set forth in the Instruction Manual.

• TO THE EXTENT PERMITTED BY LAW, IN NO EVENT SHALL WE BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR

CONSEQUENTIAL DAMAGES, INCLUDING ANY ECONOMIC LOSS, WHETHER RESULTING FROM NONPERFORMANCE,

USE, MISUSE OR INABILITY TO USE THE CRAFTSMAN PRODUCT OR FOR THE NEGLIGENCE OF ETC.

How to Obtain Service

US and Canada – To obtain warranty benefits contact us toll free at 1-888-331-4569 (Mexico 001-881-331-4569).

We will direct you to the nearest service center to review your vacuum for inspection, repairs or replacement.

Mexico - To obtain warranty benefits contact us toll free at 001-881-331-4569. We will direct you to the nearest service

center to review your vacuum for inspection, repairs or replacement.

No Other Express Warranty Applies

This limited warranty is the sole and exclusive warranty provided to You. No other express warranty, written or verbal,

applies including, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

No employee, agent, dealer, or other person is authorized to alter this limited warranty or make any other warranty on

behalf of Us.

What We will do to Correct Problems

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE LIMITED TO REPAIR, REPLACEMENT,

REFUND OF THE CRAFTSMAN PRODUCT.

After You have contacted CRAFTSMAN Product Customer Service Department, We will initiate warranty proceedings,

including a physical inspection, subject to the exclusions and the Warranty Period stated herein, to determine whether to

repair or replace the CRAFTSMAN Product or provide You with a refund.

The decision to repair or replace your CRAFTSMAN Product or to provide a refund is at Our sole discretion. Repair or

replacements provided to You by ETC are at no cost to You if covered under this limited warranty.

If we are unable to provide You with a suitable repaired or replacement CRAFTSMAN Product, we will provide you with

a refund equal to the purchase price of your CRAFTSMAN Product or a credit to be used toward the purchase of a new

CRAFTSMAN Product.

In the event of any dispute between CUSTOMER AND US, either party may choose to resolve the dispute by binding

arbitration. THIS MEANS IF EITHER CUSTOMER OR US CHOOSE BINDING ARBITRATION, NEITHER PARTY SHALL HAVE THE

RIGHT TO LITIGATE SUCH CLAIM IN COURT OR HAVE A JURY TRIAL. DISCOVERY AND APPEAL RIGHTS ARE LIMITED.

This limited warranty gives you specific legal rights, and you may also have other rights, which vary from State to State.

Some states do not allow the exclusion of incidental or consequential damages, so the above limitation may not apply.

SP7088-2 CMXEVBE175850.indb 17 10/24/19 11:59 AM

Part No. SP7088 Form No. SP7088-2 Printed in Mexico 10/2019

CRAFTSMAN®

is a registered trademark of Stanley Black & Decker, Inc., used under license.

es una marca registrada de Stanley Black & Decker, Inc., utilizada bajo licencia.

est une marque déposée de Stanley Black & Decker, Inc., utilisée sous licence.

2019 CRAFTSMAN

Product Manufactured by: EMERSON TOOL COMPANY

Producto fabricado por: 8100 W. Florissant • St. Louis, MO 63136

Produit fabriqué par : U.S. & Canada Only • É.-U. et Canada seulement • EE.UU. y Canadá solamente

SP7088-2 CMXEVBE175850.indb 18 10/24/19 11:59 AM

Page is loading ...

Pièce N° SP7088 Imprimé N° SP7088-2 Imprimé au Mexique 10/2019

CRAFTSMAN®

is a registered trademark of Stanley Black & Decker, Inc., used under license.

es una marca registrada de Stanley Black & Decker, Inc., utilizada bajo licencio.

est une marque déposée de Stanley Black & Decker, Inc., utilisée sous licence.

2019 CRAFTSMAN

Product Manufactured by: EMERSON TOOL COMPANY

Producto fabricado por: 8100 W. Florissant • St. Louis, MO 63136

Produit fabriqué par : U.S. & Canada Only • É.-U. et Canada seulement

SP7088-2 CMXEVBE175850.indb 35 10/24/19 11:59 AM

Page is loading ...

Craftsman CMXEVBE17585 User manual

Brand: Craftsman

Model: CMXEVBE17585

Category: Vacuum cleaners

Type: User manual

Download PDF

report

in other languages

français: Craftsman CMXEVBE17585 Manuel utilisateur
español: Craftsman CMXEVBE17585 Manual de usuario

Craftsman CMXEVBE17585 User manual

Craftsman CMXEVBE17585 User manual

in other languages

Related papers

Other documents