Pelgrim GVW557RVS User manual

Gebruiks-

aanwijzing

Afwasmachine

Notice

d'utilisation

Lave-vaisselle

Benutzer-

information

Geschirrspüler

User manual

Dishwasher

GVW557RVS

Page is loading ...

Contents

Safety information 55

Product description 56

Control panel 57

Use of the appliance 58

Setting the water softener 58

Use of dishwasher salt 59

Use of rinse aid 60

Loading cutlery and dishes 61

Use of detergent 63

Setting and starting a washing programme

64

Washing programmes 65

Care and cleaning 66

What to do if… 67

Technical data 69

Installation 69

Water connection 69

Electrical connection 70

Environment concerns 71

Subject to change without notice

Safety information

For your safety and correct operation of

the appliance, read this manual carefully

before installation and use. Always keep

these instructions with the appliance

even if you move or sell it. Users must

fully know the operation and safety fea-

tures of the appliance.

Correct use

• The appliance is designed exclusively for

domestic use.

• Only use the appliance to clean household

utensils that are applicable for dishwash-

ers.

• Do not put solvents in the appliance. Risk

of explosion.

• Put the knives and all items with sharp

points in the cutlery basket with their

points down. If not, put in a horizontal po-

sition in the upper basket.

• Use only branded products for dishwash-

ers (detergent, salt, rinse aid).

• If you open the door while the appliance is

in operation, hot steam can escape. Risk

of skin burns.

•Do not remove dishes from the dishwasher

before the end of the washing programme.

• When the washing programme is comple-

ted, disconnect the mains plug from the

mains socket and close the water tap.

• Only an authorised service engineer can

repair this appliance. Use only original

spare parts.

• Do not do repairs yourself to prevent injury

and damage to the appliance. Always con-

tact your local Service Force Centre.

General safety

• Persons (including children) with reduced

physical sensory, mental capabilities or

lack of experience and knowledge must

not use the appliance. They must have su-

pervision or instruction for the operation of

the appliance by a person responsible for

their safety.

• Obey the safety instructions from the man-

ufacturer of the dishwasher detergent to

prevent burns to eyes, mouth and throat.

• Do not drink the water from the dishwash-

er. Detergent residues can stay in your ap-

pliance.

• Always close the door when you do not

use the appliance to prevent injury and not

to stumble over the open door.

• Do not sit or stand on the open door.

Child safety

• Only adults can use this appliance. Chil-

dren must get supervision to make sure

that they do not play with the appliance.

• Keep all the packaging away from children.

There is a risk of suffocation.

• Keep all detergents in a safe area. Do not

let children touch the detergents.

• Keep children away from the appliance

when the door is open.

55

Installation

• Make sure that the appliance is not dam-

aged because of transport. Do not con-

nect a damaged appliance. If necessary,

contact the supplier.

• Remove all packaging before first use.

• A qualified and competent person must do

the electrical installation.

• A qualified and competent person must do

the plumbing installation.

• Do not change the specifications or modify

this product. Risk of injury and damage to

the appliance.

• Do not use the appliance:

– if the mains cable or water hoses are

damaged,

– if the control panel, worktop or plinth

area are damaged, that you can get ac-

cess to the inner side of the appliance.

Contact your local Service Force Centre.

• Do not drill into the sides of the appliance

to prevent damage to hydraulic and elec-

trical components.

Warning! Carefully obey the

instructions for electrical and water

connections.

Product description

1 Upper basket

2 Water hardness dial

3 Salt container

4 Detergent dispenser

5 Rinse aid dispenser

6 Rating plate

7 Filters

8 Lower spray arm

9 Upper spray arm

56

Control panel

1 3 42

5

ABC

1 On/off button

2 Programme selection buttons

3 Delay start button

4 Indicator lights

5 Function buttons

Indicator lights

End-of-programme Comes on when the washing programme is completed.

Auxiliary functions:

• Level of the water softener.

• Activation/deactivation of the audible signals.

• An alarm if the appliance has a malfunction.

Rinse aid

1)

Comes on when it is necessary to fill the rinse aid dispens-

er. Refer to the chapter 'Use of rinse aid'.

Salt

1)

Comes on when it is necessary to fill the salt container.

Refer to the chapter 'Use of dishwasher salt'.

After you fill the container, the salt indicator light can con-

tinue to stay on for some hours. This does not have an

unwanted effect on the operation of the appliance.

1) When the salt and/or rinse aid containers are empty, the related indicator lights do not come on while

a washing programme operates.

Function buttons

Use the function buttons for these opera-

tions:

• To set the water softener. Refer to the

chapter 'Setting the water softener'.

• To deactivate/activate the audible signals.

Refer to the section 'Audible signals'.

• To cancel the washing programme in pro-

gress or a delay start in progress. Refer to

the chapter 'Setting and starting a washing

programme'.

Delay start button

Use the delay start button to delay the start

of the washing programme with an interval of

3, 6 or 9 hours. Refer to the chapter 'Setting

and starting a washing programme'.

Setting mode

The appliance is in setting mode when all the

programme indicator lights are on.

The appliance must be in setting mode for

these operations:

– To set a washing programme.

– To set the water softener level.

– To deactivate/activate the audible signals.

57

If a programme indicator light is on, cancel

the programme to go back to the setting

mode. Refer to the chapter "Setting and

starting a washing programme".

Audible signals

You can hear an audible signal:

• At the end of the washing programme.

• During the setting of the level of the water

softener.

• When the appliance has a malfunction.

The activation of the audible signals is set at

the factory.

Do these steps to deactivate the audible sig-

nals:

1. Switch on the appliance.

2. Make sure that the appliance is in setting

mode.

3. Press and hold function buttons B and C

until the indicator lights of function but-

tons A, B and C start to flash.

4. Press the function button C.

– Indicator lights for function buttons A

and B go off.

– Indicator light for function button C

starts to flash.

– The end indicator light comes on.

The audible signals are activated.

5. Press the function button C again.

– The end indicator light goes off.

The audible signals are deactivated.

6. Switch off the appliance to save the op-

eration.

Do these steps to activate the audible sig-

nals:

1. Do the above procedure until the end in-

dicator light comes on.

Use of the appliance

Refer to the following instructions for each

step of procedure:

1. Make a check if the water softener level

is correct for the water hardness in your

area. If necessary set the water softener.

2. Fill the salt container with dishwasher salt.

3. Fill the rinse aid dispenser with rinse aid.

4. Load cutlery and dishes into the dish-

washer.

5. Set the correct washing programme for

the type of load and soil.

6. Fill the detergent dispenser with the cor-

rect quantity of detergent.

7. Start the washing programme.

If you use detergent tablets, refer to the

chapter 'Use of detergent'.

Setting the water softener

The water softener removes minerals and

salts from the water supply. Minerals and

salts can have bad effect on the operation of

the appliance.

Water hardness is measured in equivalent

scales:

• German degrees (dH°).

• French degrees (°TH).

• mmol/l (millimol per litre - international unit

for the hardness of water).

•Clarke.

Adjust the water softener to the water hard-

ness in your area. If necessary, contact your

local water authority.

Water hardness Water hardness setting

°dH °TH mmol/l Clarke manually electronically

51 - 70 91 - 125 9,1 - 12,5 64 - 88 2 10

43 - 50 76 - 90 7,6 - 9,0 53 - 63 2 9

37 - 42 65 - 75 6,5 - 7,5 46 - 52 2 8

29 - 36 51 - 64 5,1 - 6,4 36 - 45 2 7

23 - 28 40 - 50 4,0 - 5,0 28 - 35 2 6

19 - 22 33 - 39 3,3 - 3,9 23 - 27 2 5

15 - 18 26 - 32 2,6 - 3,2 18 - 22 1 4

58

Water hardness Water hardness setting

°dH °TH mmol/l Clarke manually electronically

11 - 14 19 - 25 1,9 - 2,5 13 - 17 1 3

4 - 10 7 - 18 0,7 - 1,8 5 - 12 1 2

< 4 < 7 < 0,7 < 5

1

1)

1

1)

1) No use of salt required.

You must set the water softener man-

ually and electronically.

Manual adjustment

The appliance is set at the factory at po-

sition 2.

1. Open the door.

2. Remove the lower basket.

3. Turn the water hardness dial to position

1 or 2 (refer to the chart).

4. Install the lower basket.

5. Close the door.

Electronic adjustment

The water softener is set at the factory

at level 5.

1. Switch on the appliance.

2. Make sure that the appliance is in setting

mode.

3. Press and hold function buttons B and C

until the indicator lights for function but-

tons A, B and C start to flash.

4. Release function buttons B and C.

5. Press function button A.

– The indicator light for function button A

continues to flash.

– The indicator lights for function buttons

B and C go off.

– The end-of-programme indicator light

starts to flash.

– You can hear an audible signal.

The setting function of the water softener

is activated.

The end-of-programme indicator light

flashes and an audible signal operates to

show the level of the water softener. The

pause is approximately 3 seconds.

Example: 5 flashes / 5 intermittent audible

signals - pause - 5 flashes / 5 intermittent

audible signals - pause - etc. = level 5

6. Press the function button A one time to

increase the water softener level by one

step.

7. Press the on/off button to save the oper-

ation.

Use of dishwasher salt

Caution! Only use dishwashers salt.

Types of salt that are not applicable for

dishwashers cause damage to the water

softener.

Caution! Grains of salt and salty water

on the bottom of the appliance can

cause corrosion. Fill the appliance with

salt before you start a washing

programme to prevent corrosion.

Do these steps to fill the salt container:

1. Turn the cap anticlockwise to open the

salt container.

2. Fill the salt container with 1 litre of water

(only the first operation).

3. Use the funnel to fill the salt container with

salt.

59

4. Remove the salt around the opening of

the salt container.

5. Turn the cap clockwise to close the salt

container.

It is normal that water overflows from the

salt container when you fill it with salt.

When you set electronically the water soft-

ener to level 1, the salt indicator light does

not stay on.

Use of rinse aid

Caution! Only use branded rinse aid for

dishwashers.

Do not fill the rinse aid dispenser with

other products (e.g. dishwasher clean-

ing agent, liquid detergent). This can

cause damage to the appliance.

Rinse aid makes it possible to dry the

dishes without streaks and stains.

Rinse aid is automatically added during

the last rinsing phase.

Do these steps to fill the rinse aid dispenser:

1. Press the release button (A) to open the

rinse aid dispenser.

2. Fill the rinse aid dispenser with rinse aid.

The mark 'max.' shows the maximum

level.

3. Remove the spilled rinse aid with an ab-

sorbent cloth to prevent too much foam

during the subsequent washing pro-

gramme.

4. Close the rinse aid dispenser.

Adjusting the rinse aid dosage

The rinse aid is set at the factory at position

4.

You can set the rinse aid dosage between

position 1 (lowest dosage) and position 6

(highest dosage).

60

1. Turn the rinse aid dial to increase or de-

crease the dosage.

– Increase the dosage if there are water

droplets or limescale on the dishes.

– Decrease the dosage if there are

streaks, whitish stains or bluish layers

on the dishes.

Loading cutlery and dishes

Helpful hints and tips

Caution! Only use the appliance for

household utensils that are applicable

for dishwashers.

Do not use the appliance to clean objects

that can absorb water (sponges, household

cloths, etc.).

• Before you load cutlery and dishes, do

these steps:

– Remove all food remainings and debris.

– Make burnt, remaining food in pans soft.

• While you load cutlery and dishes, do

these steps:

– Load hollow items (e.g. cups, glasses

and pans) with the opening down.

– Make sure that water does not collect in

the container or in a deep base.

– Make sure that cutlery and dishes do not

lie inside one another.

– Make sure that cutlery and dishes do not

cover other cutlery and dishes.

– Make sure that glasses do not touch

other glasses.

– Put small objects in the cutlery basket.

• Plastic items and pans with non-stick

coatings can keep water droplets. Plastic

items do not dry as well as porcelain and

steel items.

• Put light items in the upper basket. Make

sure that the items do not move.

Caution! Make sure that the spray arms

can move freely before you start a

washing programme.

Warning! Always close the door after

you load or unload the appliance. An

open door can be dangerous.

Lower basket

Put saucepans, lids, plates, salad bowls and

cutlery in the lower basket. Arrange service

dishes and large lids around the edge of the

basket.

61

The rows of prongs in the lower basket can

be flat to load pots, pans and bowls.

Cutlery basket

Warning! Do not put long-bladed knives

in a vertical position. Arrange long and

sharp cutlery horizontally in the upper

basket. Be careful with sharp items.

Put forks and spoons with the handles down.

Put knives with the handles up.

Mix spoons with other cutlery to prevent

them to bond together.

Use the cutlery grid. If the dimensions of the

cutlery prevent the use of the cutlery grid, you

can remove it.

Upper basket

The upper basket is for plates (maximum 24

cm in diameter), saucers, salad bowls, cups,

glasses, pots and lids. Arrange the items to

let water touch all surfaces.

Prevent to put plates in the first three

sectors in the front part of the basket.

Make sure the plates tilt forward.

Put glasses with long stems in the cup racks

with the stems up. For longer items, fold the

cup racks up.

Adjustment of the height of the upper

basket

If you put large plates in the lower basket, first

move the upper basket to the upper position.

Maximum height of the dishes

upper bas-

ket

lower

basket

Upper position 20 cm 31 cm

Lower position 24 cm 27 cm

Do these steps to move the upper basket to

the upper position:

62

1. Pull the basket out until it stops.

2. Carefully lift the two sides until the mech-

anism is engaged and the basket is sta-

ble.

Do these steps to move the upper basket to

the lower position:

1. Pull the basket out until it stops.

2. Carefully lift the two sides upwards.

3. Hold the mechanism and let it fall back

down slowly.

Caution!

• Do not lift or lower the basket on one

side only.

• If the basket is in the upper position,

do not put cups on the cup racks.

Use of detergent

Only use detergents (powder, liquid or

tablet) that are applicable for dishwash-

ers.

Follow the data on the packaging:

• Dosage recommended by the manu-

facturer.

• Storage recommendations.

Do not use more than the correct quan-

tity of detergent to save an environment.

Do these steps to fill the detergent dispenser:

1. Open the lid of the detergent dispenser.

2. Fill the detergent dispenser (A) with de-

tergent. The marking shows the dosage:

20 = approximately 20 g of detergent

30 = approximately 30 g of detergent.

3. If you use a washing programme with

prewash phase, put more detergent in

the prewash detergent compartment (B).

A

B

4. If you use detergent tablets, put the de-

tergent tablet in the detergent dispenser

(A).

63

5. Close the lid of the detergent dispenser.

Press the lid until it locks into position.

Different brands of detergent dissolve in

different times. Some detergent tablets

do not have the best cleaning results

during short washing programmes. Use

long washing programmes when you

use detergent tablets to fully remove the

detergent.

Use of combi detergent tablets

These tablets contain agents such as deter-

gent, rinse aid and dishwasher salt. Some

types of tablets can contain other agents

When you use tablets, that contain special

salt and rinse aid, it is not necessary to fill the

salt and rinse aid containers. In this condition

the rinse aid indicator light stays on when the

appliance is switched on.

1. Do a check if these tablets are applicable

for the local water hardness. Refer to the

instructions from the manufacturer.

2. Select the lowest setting for the water

hardness and rinse aid dosage.

Do these steps if the drying results are not

satisfactory

1. Fill the rinse aid dispenser with rinse aid.

2. Set the rinse aid dosage to position 2.

To use normal detergent again

1. Fill the salt container and rinse aid dis-

penser.

2. Adjust the water hardness setting to the

highest level.

3. Do a washing programme without

dishes.

4. Adjust the water softener to the water

hardness in your area.

5. Adjust the rinse aid dosage.

Setting and starting a washing programme

Set the washing programme with the

door ajar. The washing programme only

starts after you close the door. Until then

it is possible to modify the settings.

Do these steps to set and start a washing

programme:

1. Switch on the appliance.

2. Make sure that the appliance is in setting

mode.

3. Press one of the programme buttons.

Refer to the chapter 'Washing pro-

grammes'.

– The programme indicator light comes

on.

4. Close the door.

– The washing programme starts.

When the washing programme oper-

ates, you cannot change the pro-

gramme. Cancel the washing pro-

gramme.

Warning! Only interrupt or cancel a

washing programme if necessary.

Caution! Open the door carefully. Hot

steam can come free.

Cancelling a washing programme

1. Press and hold function buttons B and C

until all the programme lights come on.

2. Release function buttons B and C to can-

cel the washing programme.

At this time you can do these steps:

1. Switch off the appliance.

2. Set a new washing programme .

Fill the detergent dispenser with detergent

before you set a new washing programme.

Interrupting a washing programme

Open the door.

• The programme stops.

Close the door.

• The programme continues from the point

of interruption.

64

Setting and starting a washing

programme with delay start

1. Press the on/off button.

2. Set a washing programme.

– The programme indicator light comes

on.

3. Press the delay start button until the in-

dicator light with the correct number of

hours starts to flash (3, 6, or 9 hours).

4. Close the door.

– The countdown of the delay start

starts.

– The countdown of the delay start de-

creases with steps of 3 hours.

When the countdown is completed,

the washing programme starts auto-

matically.

Do not open the door during the count-

down to prevent interruption of the

countdown. When you close the door

again, the countdown continues from

the point of interruption.

Cancelling a delay start:

1. Press and hold function buttons B and C

until all the programme lights come on.

– When you cancel a delay start, you also

cancel the washing programme.

2. Set a new washing programme.

End of the washing programme

Switch off the appliance in these conditions:

• The appliance stops automatically.

• The audible signals for the end of the pro-

gramme operate.

1. Open the door.

– The end indicator light comes on.

– The programme indicator light stays

on.

2. Press the on/off button.

3. For better drying results, keep the door

ajar for some minutes before you remove

the dishes.

Let the dishes cool down before you remove

them from the appliance. Hot dishes are

easily damaged.

Removing the load

• First remove items from the lower basket,

then from the upper basket.

• There can be water on the sides and door

of the appliance. Stainless steel becomes

cool more quickly than the dishes.

Washing programmes

Programme Degree of soil Type of load Programme description

Heavy soil Crockery, cutlery, pots

and pans

Prewash

Main wash up to 70°C

2 intermediate rinses

Final rinse

Drying

Auto

1)

Any Crockery, cutlery, pots

and pans

Prewash

Main wash up to 45°C or 70°C

1 or 2 intermediate rinses

Final rinse

Drying

Normal soil Crockery and cutlery Main wash up to 50°C

1 intermediate rinse

Final rinse

Drying

2)

Normal or light

soil

Crockery and cutlery Main wash up to 60 °C

Final rinse

65

Programme Degree of soil Type of load Programme description

3)

Normal soil Crockery and cutlery Prewash

Main wash up to 50°C

1 intermediate rinse

Final rinse

Drying

1) During the Auto programme, the soil level of the dishes is given by how cloudy the water is. The

programme duration and consumptions can change. This depends if the appliance is fully or not and

on the level of soil on the dishes. The appliance adjusts automatically the temperature of the water

during the main wash.

2) This is the perfect daily programme to clean a not fully load. Ideal for a family of 4 persons who only

want to load breakfast and dinner crockery and cutlery.

3) Test programme for test institutes. Please refer to separate leaflet supplied, for test data.

Consumption values

Programme Duration (in minutes) Energy (in kWh) Water (in litres)

80-90 1,6-1,8 22-24

Auto 90-140 1,1-1,8 12-23

45-55 1,0-1,2 11-22

30 0,9 9

150-160 1,0-1,1 13-15

The pressure and temperature of the

water, the variations of power supply

and the quantity of dishes can change

these values.

Care and cleaning

Warning! Switch the appliance off

before you clean the filters.

Cleaning the filters

Caution! Do not use the appliance

without the filters. Make sure that the

installation of the filters is correct.

Incorrect installation will cause

unsatisfactory washing results and

damage to the appliance.

If necessary, clean the filters. Dirty filters de-

crease the washing results.

The dishwasher has three filters:

1. coarse filter (A)

2. microfilter (B)

3. flat filter (C)

A

B

C

A

B

C

Do these steps to clean the filters:

1. Open the door.

2. Remove the lower basket.

3. To unlock the filter system, turn the han-

dle on the microfilter (B) approximately

1/4 anticlockwise.

66

4. Remove the filter system.

5. Hold the coarse filter (A) by the handle

with the hole.

6. Remove the coarse filter (A) from the mi-

crofilter (B).

7. Remove the flat filter (C) from the bottom

of the appliance.

D

8. Clean the filters below running water.

9. Put the flat filter (C) in the bottom of the

appliance. Install the flat filter correctly

under the two guide (D).

10. Put the coarse filter (A) in the microfilter

(B) and push the filters together.

11. Put the filter system in position.

12. To lock the filter system, turn the handle

on the microfilter (B) clockwise until it

lock in position.

13. Install the lower basket.

14. Close the door.

Do not remove the spray arms.

If the holes in the spray arms become clog-

ged, remove remaining parts of soil with a

cocktail stick.

External cleaning

Clean the external surfaces of the appliance

and control panel with a damp soft cloth.

Only use neutral detergents. Do not use

abrasive products, scouring pads or solvents

(acetone, trichloroethylene etc...).

Frost precautions

Caution! Do not install the appliance

where the temperature is below 0 °C.

The manufacturer is not responsible for

damage because of frost.

If not possible, empty the appliance and

close the door. Disconnect the water inlet

hose and remove water from the water inlet

hose.

What to do if…

The appliance does not start or stops during

operation.

If there is a fault, first try to find a solution to

the problem yourself. If you cannot find a sol-

ution to the problem yourself, contact the

Service Force Centre.

Caution! Switch off the appliance

before you do the below suggested

corrective actions.

67

Fault code and malfunction Possible cause and solution

• continuous flash of the light of the

running programme

• intermittent audible signal

• 1 flash of the end indicator light

The dishwasher does not fill with wa-

ter

• The water tap is blocked or furred with limescale.

Clean the water tap.

• The water tap is closed.

Open the water tap.

• The filter in the water inlet hose is blocked.

Clean the filter.

• The connection of the water inlet hose is not correct. The

hose can be kinked or squashed.

Make sure that the connection is correct.

• continuous flash of the light of the

running programme

• intermittent audible signal

• 2 flashes of the end indicator light

The dishwasher will not drain

• There is a blockage in the sink spigot.

Clean the sink spigot.

• The connection of the water drain hose is not correct. The

hose can be kinked or squashed.

Make sure that the connection is correct.

• continuous flash of the light of the

running programme

• intermittent audible signal

• 3 flashes of the end indicator light

The anti-flood device operates

• Close the water tap and contact your local Service Force

Centre.

The programme does not start • The appliance door is not closed.

Close the door.

• Mains plug is not connected in.

Put in the mains.

• The fuse has blown out in the household fuse box.

Replace the fuse.

• Delay start is set.

Cancel the delay start to start the programme immediately.

After the check, switch on the appliance. The

programme continues from the point of in-

terruption. If the malfunction shows again,

contact your Service Force Centre.

These data are necessary to help you quickly

and correctly:

•Model (Mod.)

• Product number (PNC)

• Serial number (S.N.)

For these data, refer to the rating plate.

Write the necessary data here:

Model description : ..........

Product number : ..........

Serial number : ..........

The cleaning results are not satisfactory

The dishes are not clean • The selected washing programme is not applicable for the type of

load and soil.

• The baskets are loaded incorrectly so that water cannot reach all

surfaces.

• Spray arms do not turn freely because of incorrect arrangement of

the load.

• The filters are dirty or not correctly installed.

• The quantity of detergent is too little or missing.

Limescales particles on the

dishes

• The salt container is empty.

• The water softener is adjusted on a wrong level.

• The salt container cap is not closed correctly.

The dishes are wet and dull • No rinse aid has been used.

• The rinse aid dispenser is empty.

There are streaks, milky spots

or a bluish coating on glasses

and dishes

• Decrease the rinse aid dosage.

68

The cleaning results are not satisfactory

Dry water drop signs on

glasses and dishes

• Increase rinse aid dosage.

• The detergent can be the cause.

Technical data

Dimensions Width cm 59,6

Height cm 81,8-87,8

Depth cm 55,5

Electrical connection - Voltage -

Overall power - Fuse

Information on the electrical connection is given on the rating plate

on the inner edge of the dishwasher door.

Water supply pressure Minimum 0,5 bar (0,05 MPa)

Maximum 8 bar (0,8 MPa)

Capacity Place settings 12

Installation

Warning! Make sure that mains plug is

disconnected from the mains socket

during installation.

Important! Obey the instructions in the

enclosed template to:

• Build-in the appliance.

• Install the furniture panel.

• Connect to the water supply and drain.

Install the appliance under a counter (kitchen

worktop or sink).

If a repair is necessary, the appliance must

be easily accessible for the engineer.

Put the appliance adjacent to a water tap and

a drain.

For the venting of the dishwasher only water

fill, water drain and power supply cable open-

ings are necessary.

The dishwasher has adjustable feet to allow

the adjustment of the height.

Make sure that the water inlet hose, the drain

hose and the supply cable are not kinked or

squashed, when you insert the machine.

Attaching the appliance to the adjacent

units

Make sure that the counter below which you

attach the appliance is a safe structure (ad-

jacent kitchen units, cabinets, wall).

Adjusting the level of the appliance

Make sure that the appliance is level to close

and seal the door correctly. If the level of the

appliance is correct, the door does not catch

on the sides of the cabinet. If the door does

not close correctly, loosen or tighten the ad-

justable feet until the appliance is level.

Water connection

Water inlet hose

Connected the appliance to a hot (max. 60°)

or cold water supply.

If the hot water comes from alternative sour-

ces of energy that are more environmentally

friendly (e.g. solar or photovoltaic panels and

aeolian), use a hot water supply to decrease

energy consumption.

Connect the inlet hose to a water tap with an

external thread of 3/4”.

Caution! Do not use connection hoses

from an old appliance.

The water pressure must be in the limits (refer

to 'Technical data'). Make sure that the local

water authority gives you the average mains

pressure in your area.

Make sure that there are no kinks in the water

inlet hose and that the water inlet hose is not

squashed or entangled.

69

Fit the locknut correctly to prevent water

leaks.

Caution! Do not connect the appliance

to new pipes or pipes that are not used

for a long time. Let the water run for

some minutes, then connect the inlet

hose.

The water inlet hose is double-walled and

has an inner mains cable and a safety valve.

The water inlet hose is under pressure only

while the water is running. If there is a leak in

the water inlet hose, the safety valve inter-

rupts the running water.

Be careful when you connect the water inlet

hose:

• Do not put the water inlet hose or the safe-

ty valve in water.

• If the water inlet hose or the safety valve is

damaged, immediately disconnect the

mains plug from the mains socket.

• Only let the Service Force Centre replace

the water inlet hose with safety valve.

Warning! Dangerous voltage

Water drain hose

1. Connect the water drain hose to the sink

spigot and attach it under the work sur-

face. This prevents that the waste water

from the sink goes back into the appli-

ance.

2. Connect the water drain hose to a stand

pipe with vent-hole (minimum internal di-

ameter 4 cm).

max 85 cm

min 40 cm

max 400 cm

Make sure that the drain hose is not bent or

squashed to prevent that the water drains

does not drain correctly.

Remove the sink plug when the appliance

drains the water to prevent that the water

goes back into the appliance.

A drain hose extension must not be longer

than 2 m. The internal diameter must not be

smaller than the diameter of the hose.

If you connect the water drain hose to a trap

spigot under the sink, remove the plastic

membrane (A). If you do not remove the

membrane, remaining food can cause a

blockage in the drain hose spigot

The appliance has a security feature to

prevent that dirty water goes back into

the appliance. If, the spigot of the sink

has a 'non-return valve', this valve can

cause the appliance to drain incorrectly.

Remove the non-return valve.

Caution! Make sure that the water

couplings are tight to prevent water

leakage.

Electrical connection

Warning! The manufacturer is not

responsible if you do not follow these

safety precautions.

Ground the appliance according to safe-

ty precautions.

Make sure that the rated voltage and

type of power on the rating plate agree

with the voltage and the power of the lo-

cal power supply.

Always use a correctly installed shock-

proof socket.

Do not use multi-way plugs, connectors

and extension cables. There is a risk of

fire.

70

Do not replace the mains cable yourself.

Contact the Service Force Centre.

Make sure that the mains plug is acces-

sible after installation.

Do not pull the mains cable to discon-

nect the appliance. Always pull the

mains plug.

Environment concerns

The symbol on the product or on its

packaging indicates that this product may

not be treated as household waste. Instead

it should be taken to the appropriate

collection point for the recycling of electrical

and electronic equipment. By ensuring this

product is disposed of correctly, you will help

prevent potential negative consequences for

the environment and human health, which

could otherwise be caused by inappropriate

waste handling of this product. For more

detailed information about recycling of this

product, please contact your local council,

your household waste disposal service or the

shop where you purchased the product.

The packaging materials are environmentally

friendly and can be recycled. The plastic

components are identified by markings, e.g.

>PE<, >PS<, etc. Discard the packaging

materials in the applicable container at the

community waste disposal facilities.

Warning! To discard the appliance,

follow the procedure:

• Pull the mains plug out of the socket.

• Cut off the mains cable and mains

plug and discard them.

• Discard the door catch. This prevents

the children to close themselves in-

side the appliance and endanger their

lives.

71

Page is loading ...

Pelgrim GVW557RVS User manual

This manual is also suitable for

Pelgrim GVW557RVS User manual

in other languages

Related papers

Other documents