Playstation 4-198-819-12 User manual

Page is loading ...

2

WARNING

To avoid electrical shock, do not open the cabinet. Refer

servicing to qualified personnel only.

Caution

Use of controls or adjustments or performance of

procedures other than those specified herein may result in

hazardous radiation exposure.

The use of optical instruments with this product will

increase eye hazard.

This appliance is classified as a CLASS 1 LASER product under IEC60825-

1:2007.

This equipment complies with FCC/IC radiation exposure limits set forth for

uncontrolled equipment and meets the FCC radio frequency (RF) Exposure

Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF)

Exposure rules. This equipment should be installed and operated with at least 20

cm (8 in) and more between the radiator and person’s body (excluding

extremities: hands, wrists, feet and legs).

This transmitter must not be co-located or operated in conjunction with any other

antenna or transmitter.

The wireless controller complies with FCC/IC radiation exposure limits set forth for

uncontrolled equipment and meets the FCC radio frequency (RF) Exposure

Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF)

Exposure rules. This equipment has very low levels of RF energy that are deemed

to comply without testing of specific absorption ratio (SAR).

NOTE:

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following measures:

−

Reorient or relocate the receiving antenna.

− Increase the separation between the equipment and receiver.

− Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

−

Consult the dealer or an experienced radio/TV technician for help.

You are cautioned that any changes or modifications not expressly approved by

the party responsible for compliance could void the user’s authority to operate the

equipment.

3

WARNING

US

If you have questions about this product, call our technical support line at

1-800-345-7669 or write to:

Sony Computer Entertainment America

Consumer Services/Technical Support

PO Box 5888, San Mateo, CA 94402-0888 U.S.A.

Declaration of Conformity

Trade Name : SONY

Model No. : CECH-2501B

Responsible Party : Sony Electronics Inc.

Address : 16530 Via Esprillo

San Diego, CA 92127 U.S.A.

T

elephone No. : 858-942-2230

This device complies with Part 15 of the FCC Rules and RSS-Gen of IC

Rules. Operation is subject to the following two conditions: (1) this device

may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired

operation of this device.

Photosensitivity/Epilepsy/Seizures

A very small percentage of individuals may experience epileptic seizures or

blackouts when exposed to certain light patterns or flashing lights. Exposure to

certain patterns or backgrounds on a television screen or when playing video

games may trigger epileptic seizures or blackouts in these individuals. These

conditions may trigger previously undetected epileptic symptoms or seizures in

persons who have no history of prior seizures or epilepsy. If you, or anyone in your

family, has an epileptic condition or has had seizures of any kind, consult your

physician before playing.

IMMEDIATELY DISCONTINUE use and consult your physician before resuming

gameplay if you or your child experience any of the following health problems or

symptoms:



dizziness,



altered vision,



eye or muscle twitches,



loss of awareness,



disorientation,



seizures, or



any involuntary movement or convulsion.

RESUME GAMEPLAY ONLY ON APPROVAL OF YOUR PHYSICIAN.

Use and handling of video games to reduce the likelihood of a

seizure



Use in a well-lit area and keep as far away as possible from the television

screen.



Avoid large screen televisions. Use the smallest television screen available.



Avoid prolonged use of the PS3™ system. Take a 15-minute break during each

hour of play.



Avoid playing when you are tired or need sleep.

About the lithium coin memory back-up battery

The lithium coin memory back-up battery inside this product contains Perchlorate.

The following statement is required by the State of California, USA:

Perchlorate Material - special handling may apply, See

http://www.dtsc.ca.gov/hazardouswaste/perchlorate

4

WARNING

Radio waves

Radio waves may affect electronic equipment or medical devices (for example,

pacemakers), which may cause malfunctions and possible injuries.



If you use a pacemaker or other medical device, consult your physician or the

manufacturer of your medical device before using the wireless networking

feature (Bluetooth

®

and wireless LAN).



Do not use the wireless networking feature in the following locations:

–

Areas where wireless network use is prohibited, such as in hospitals. Abide

by medical institution regulations when using the system on their premises.

–

Areas near fire alarms, automatic doors and other types of automated

equipment.

3D images

Some people may experience discomfort (such as eye strain, eye fatigue, or

nausea) while watching 3D video images or playing stereoscopic 3D games on

3D televisions. If you experience such discomfort you should immediately

discontinue use of your television until the discomfort subsides.

SCE recommends that all viewers take regular breaks while watching 3D video, or

playing stereoscopic 3D games. The length and frequency of necessary breaks

may vary from person to person – please take breaks that are long enough to

allow any feelings of discomfort to subside. If symptoms persist, consult your

physician.

The vision of young children (especially those under six years old) is still under

development. Consult with a physician (such as a pediatrician or eye doctor)

before allowing a young child to watch 3D video images or play stereoscopic 3D

games. When using any 3D enabled device with your PlayStation

®

3 system you

should read the instruction manual for that device and visit

www.us.playstation.com/support/3D for updated information.

PlayStation

®

and PlayStation

®

2 format software

This model of the PlayStation

®

3 system is designed to play PlayStation

®

3 format

software and has limited backward compatibility. This system is not compatible

with and will not play PlayStation

®

2 format software. Some PlayStation

®

format

software may play on this system. For more information, visit

www.us.playstation.com.

System software

The system software included within this product is subject to a limited license

from Sony Computer Entertainment Inc. Refer to http://www.scei.co.jp/ps3-eula for

further details.

About national export control

This product may fall within the scope of national export control legislation. You

must comply fully with the requirements of such legislation and of all other

applicable laws of any jurisdiction in relation to this product.

Notice about U.S. Export Administration Regulations

This product contains software that is subject to certain restrictions under the U.S.

Export Administration Regulations, and may not be exported or re-exported to

U.S. embargoed destinations. In addition this product may not be exported or

re-exported to persons and entities prohibited by the U.S. Export Administration

Regulations.

5

Table of contents

US

Part names ...............................................................................12

Getting started .......................................................................... 13

Connection methods ......................................................................13

Performing initial setup of the system software ..............................15

Video output on the PS3™ system ................................................16

Connecting digital audio devices ...................................................20

Turning the PS3™ system on and off ....................................... 21

Using the wireless controller .....................................................22

Playing content .........................................................................24

Blu-ray Disc (BD)/DVD/CD .............................................................24

Playing content on USB devices ....................................................25

File formats that can be played or viewed ......................................25

Playing games ..........................................................................26

Game compatibility ........................................................................26

Playing games ...............................................................................26

Controller settings ..........................................................................27

Saved data for PlayStation

®

3 format software ...............................27

Saved data for PlayStation

®

format software .................................27

Adjusting network settings ........................................................28

Adjusting network settings (wired) .................................................29

Adjusting network settings (wireless) .............................................29

Adjusting custom settings ..............................................................31

Connecting to the Internet ........................................................ 32

Using the Internet browser .............................................................32

Viewing the user’s guide ................................................................32

Creating a PlayStation

®

Network account .......................................32

PS3™ system updates .............................................................33

Using the on-screen keyboard .................................................. 34

Parental control ........................................................................35

Replacing the hard disk ............................................................36

Backing up data .............................................................................36

Removing the hard disk .................................................................37

Replacing the hard disk .................................................................39

Reinstalling the system software ...................................................40

Restoring data that has been backed up .......................................40

Transferring data to another PS3™ system /

restoring the system ................................................................. 42

Transferring data to another PS3™ system ...................................42

Restoring the PS3™ system ..........................................................42

Before disposing of or transferring the PS3™ system ...................42

Before requesting service .........................................................43

Table of contents

WARNING ......................................................................................... 2

Precautions ....................................................................................... 6

Online information about the PS3™ system ................................... 10

XMB

™

(XrossMediaBar) menu .......................................................11

Specifications ..................................................................................48

LIMITED HARDWARE WARRANTY AND LIABILITY ..................... 53

Copyright and trademarks ...............................................................55

6

Precautions

Before using this product, carefully read all the precautions.

Safety

This product has been designed with the highest concern for safety. However, any

electrical device, if used improperly, has the potential for causing fire, electrical

shock or personal injury. To help ensure accident-free operation, follow these

guidelines:





Observe all warnings, precautions and instructions.





Regularly inspect the AC power cord for damage.





Stop use, unplug the AC power cord from the electrical outlet and disconnect

any other cables immediately if the device functions in an abnormal manner,

produces unusual sounds or smells or becomes too hot to touch.





For more information on product safety and support, visit our website (

back

cover).

Use and handling



Use in a well-lit area and keep as far away as possible from the television

screen.



Avoid prolonged use of the PS3™ system and wireless controller.



Stop using the system immediately if you begin to feel tired or if you experience

discomfort or pain in your hands or arms while operating the wireless controller.

If the condition persists, consult a doctor.



If you experience any of the following health problems, discontinue use of the

system immediately. If symptoms persist, consult with your physician.

−

Dizziness, nausea, fatigue or symptoms similar to motion sickness

− Discomfort or pain in a part of the body, such as eyes, ears, hands or arms



Keep the system and accessories, including cable ties and fasteners, out of the

reach of small children.



Do not connect cables other than a USB cable while the system is turned on

(power indicator is lit solid green).



Any TV or component connected to the system must be functioning properly

and free of defects. If a TV or component connected to the system is faulty or

defective, it may cause damage to the TV or component, or to the system itself.

As with all electrical products, connection to faulty or defective components, or

the failure to connect to a properly wired outlet, may cause sparking and pose

a fire hazard.



Do not touch the system or connected cables or accessories during an

electrical storm.



Do not use the system or accessories near water.



Do not allow liquid, small particles or other foreign objects to get into the

system or accessories.



Do not touch the connectors of the system or accessories.



Do not expose the system or accessories to dust, smoke or steam. Also, do not

place the system in an area subject to excessive dust or cigarette smoke. Dust

build-up or cigarette smoke residue on the internal components (such as the

lens) may cause the system to malfunction.



Do not expose the system or accessories to high temperatures, high humidity

or direct sunlight.



Do not place the system or accessories on surfaces that are unstable, tilted or

subject to vibration.



Do not set the system other than in the vertical or horizontal position. When

setting the system in the vertical position, use the vertical stand (sold

separately) for this model of the system. Also, do not change the position of the

system while it is turned on.



Be careful when carrying the system. If you do not have a good grip, the

system may drop causing potential damage or injury.



Do not move or change the position of the system with a disc inserted. The

vibration may result in scratching of the disc or the system.



Do not turn off the system while data is being saved on or loaded from the hard

disk.



Do not stand on or put objects on the system, and do not stack the system with

other devices.

7

Precautions

US



Do not place the system and connected accessories on the floor or in a place

where they may cause someone to trip or stumble.



Do not allow bodily contact with the system or air from the system vents for an

extended period of time while in use. Extended contact under these conditions

may cause low-temperature burns.



When connecting the system to a plasma or projection* TV, do not leave a still

image on the TV screen for an extended period of time, as this may leave a

faint image permanently on the screen.

* Except LCD screen types



Parents are encouraged to monitor children in online activities to ensure safe

and responsible Internet usage.

Notes on safety when using the DUALSHOCK

®

3

Wireless Controller*



Stop using the system immediately if you begin to feel tired or if you experience

discomfort or pain in your hands or arms while operating the DUALSHOCK

®

3

Wireless Controller. If the condition persists, consult a doctor.



The vibration function of the DUALSHOCK

®

3 Wireless Controller can aggravate

injuries. Do not use the vibration function if you have any ailment or injury to the

bones, joints or muscles of your hands or arms. If you have an ailment or an

injury, do not play software titles that contain the vibration function using the

DUALSHOCK

®

3 Wireless Controller unless you have set the vibration function

to [Off].



Avoid prolonged use of the DUALSHOCK

®

3 Wireless Controller. Take a break at

about 30-minute intervals.



Note that some software titles set the vibration function to [On] by default. To

disable the vibration function, press the PS button of the controller, and then

select [Controller Settings]

[Vibration Function] [Off]



When using the motion sensor function of the wireless controller, be cautious of

the following points. If the controller hits a person or object, this may cause

accidental injury or damage.

–

Before using, check that there is plenty of space around you.

– When using the controller, grip it firmly to make sure it cannot slip out of your

hand.

–

If using a controller that is connected to the PS3™ system with a USB cable,

make sure there is enough space for the cable so that the cable will not hit a

person or object. Also, take care to avoid pulling the cable out of the PS3™

system while using the controller.

* These notes also apply to other controllers.

Vents

Do not block any vents. To maintain good ventilation, follow the guidelines below:



Place the system at least 10 cm (4 in) away from a wall surface.



Do not place on a carpet or rug with long fibers.



Do not place in a narrow or cramped space.



Do not cover with cloth.



Do not allow dust to build up on the vents.

AC power cord use



Any TV or component connected to the system must be functioning properly

and free of defects. If a TV or component is faulty or defective, it may cause

damage to the TV or component, or to the system itself. As with all electrical

products, connection to faulty or defective components, or the failure to

connect to a properly wired outlet, may cause sparking and pose a fire hazard.



Do not plug the AC power cord for the system into an electrical outlet until you

have made all other connections. Make sure the TV or other component is

unplugged from the electrical outlet prior to connecting it to the system.



To help ensure safe operation, regularly inspect the AC power cord. If

damaged, stop use immediately and contact SCEA Consumer Services

(

back cover).



Do not use a power cord other than the supplied AC power cord. Do not modify

the cord.

8

Precautions



Do not touch the plug of the AC power cord with wet hands.



Protect the AC power cord from being walked on or pinched particularly at

plugs, expansion receptacles and the point where the cord exits from the

system.



Do not place heavy items on the cord.



Do not place the AC power cord near heating equipment and do not expose

the cord to heat.



Unplug the AC power cord from the electrical outlet before cleaning or moving

the system, or when you do not intend to use the system for an extended period

of time. When disconnecting, grasp the power cord by the plug and pull

straight out of the electrical outlet. Never pull by the cord and do not pull out at

an angle.



Do not connect the AC power cord to a voltage transformer or inverter.

Connecting the AC power cord to a voltage transformer for overseas travel or

an inverter for use in an automobile may cause heat to build up in the system

and may cause burns or a malfunction.

Never disassemble or modify the system or accessories

Use the PS3™ system and accessories according to the instructions in the

product documentation. No authorization for the analysis or modification of the

system or accessories, or the analysis and use of its circuit configurations, is

provided. Unauthorized modification of the system or accessories will void your

warranty. There are no user serviceable components inside the PS3™ system (the

supplied hard disk may be removed but not disassembled or modified).

Additionally, there is a risk of exposure to laser radiation as well as to electrical

shock.

Network



A broadband connection is required to access the Internet. Note that dial-up

connectivity is not supported.



User is responsible for Internet service fees. For details, refer to the information

provided in your service contract or contact your Internet service provider.



Do not use a cord for a standard residential telephone line or cables of types

other than those mentioned here. Using the wrong type of cord or cable can

cause more electrical current than necessary to flow through the LAN

connector, which may lead to heat build-up, fire or malfunction.

Wireless networking feature



The 2.4 GHz range of radio waves used by the wireless networking feature of

this product is a range shared by various devices. This product has been

designed to minimize the effect of other devices using the same range.

However, in some cases interference from other devices may reduce the

connection speed, shorten the signal range or cause the connection to be

terminated unexpectedly.



When using the PS3™ system’s scan function to select a wireless LAN access

point, access points that are not intended for public use may be displayed.

Only connect to an access point that you are authorized to use.

Moisture condensation

If the system or disc is brought directly from a cold location to a warm one,

moisture may condense on the lens inside the system or on the disc. Should this

occur, the system may not operate properly. In this case, remove the disc and

turn off and unplug the system. Do not put the disc back in until the moisture

evaporates (this may take several hours). If the system still does not operate

properly, contact SCEA Consumer Services (

back cover) for assistance.

Cleaning

For safety reasons, before cleaning the system or connected accessories,

disconnect the AC power cord from the electrical outlet.

9

Precautions

US

Exterior surfaces (plastic cover of system and wireless

controller)

Follow the instructions below to help prevent the product exterior from

deteriorating or becoming discolored.



Wipe with a soft, dry cloth.



Do not place any rubber or vinyl materials on the product exterior for an

extended period of time.



Do not use solvents or other chemicals. Do not wipe with a chemically-treated

cleaning cloth.

Vents

When dust accumulates in the system vents, remove the dust with a low-powered

vacuum cleaner.

Discs

Note on compatibility

Some media may have region or territorial restrictions and may not work with your

system. See media packaging for details.

Handling



Do not touch the disc surface when handling a disc; hold it by the edges.



Do not stick paper or tape onto discs and do not write on discs.



Fingerprints, dust, dirt or scratches on the disc can distort the picture or reduce

sound quality. Always handle carefully and check that discs are clean before

use.

Storage



Do not expose discs to high temperatures, high humidity or direct sunlight.



When discs will not be used for an extended period of time, store them in their

cases. Stacking uncased discs or storing them at an angle can cause them to

warp.

Cleaning method



Clean discs with a soft cloth, lightly wiping from the center

outwards.



Do not use solvents, record cleaners, anti-static spray or other

chemicals as these can damage the discs.

10

Online information about the PS3™ system

This manual explains hardware features and provides basic information about how to

set up and operate the PS3™ system, including warnings and precautions for the safe

and proper use of the system. For up-to-date information regarding the PS3™ system,

you can also access the following information available on the Internet.

Online user’s guide http://manuals.playstation.net/document/

This guide contains detailed information about using the PS3™ system software.

System software updates www.us.playstation.com/ps3

This site provides the latest information about system software updates.

PlayStation

®

3 official site www.us.playstation.com/ps3

The official site for PlayStation

®

3 products provides the latest information about software titles and

hardware accessories.

Support www.us.playstation.com/support

The official site for PlayStation

®

product support provides the latest questions and answers about

your product.

Friends

Chatting and exchanging messages

PlayStation

®

Network

Using PlayStation

®

Network services

Network

Connecting to the Internet

Game

Playing games

Video

Playing video

Music

Playing music

Photo

Displaying images

Settings

Adjusting PS3™ system settings

Users

Selecting users to log in to the PS3™

system

Check that you have all of the following items. If any items are missing, contact

SCEA Consumer Services (

back cover).

 PlayStation

®

3 system

 DUALSHOCK

®

3 Wireless Controller

 AC Power Cord

 AV Cable

 USB Cable

 Printed materials

Information about system functionality published in this document may vary from the information

for your PS3™ system, depending on the system software version in use.

11

XMB

™

(XrossMediaBar) menu

Category

Item

The PS3™ system includes a user interface called XMB

™

(XrossMediaBar).

Directional buttons:

Used to select on-screen

categories/items

button:

Displays the options

menu/control panel

button:

Cancel an operation

button:

Confirm the selected

item

PS button :

Displays the XMB

™

menu

Turns the system on/off

Quits a game

Options menu Control panel

Displayed by selecting an icon and

pressing the

button

Displayed by pressing the

button during

content playback

12

Part names

System front / rear

Disc slot

Power button

Eject button

WLAN access indicator

HDD access indicator

USB connectors

Vent

AC IN connector

AV MULTI OUT connector

DIGITAL OUT (OPTICAL)

connector

LAN connector

HDMI OUT connector

DUALSHOCK

®

3 Wireless Controller

SELECT button

USB connector

L2 button

L1 button

Directional buttons

Left stick/L3

button*

R2 button

R1 button

button

Right stick/

R3

button*

Port indicators

START button

PS button

* The L3 and R3 buttons function when the sticks are pressed.

Caution



Do not use the system in a closed cabinet or other locations where heat may

build up. Doing so may cause the system to overheat and may lead to fire,

injury or malfunction.



If the system’s internal temperature becomes elevated, the power indicator

will flash alternately in red and green. In this case, turn off the system

(

page 21) and leave it unused for a while. After the system cools down,

move it to a location with good ventilation, and then resume use.

Notices



Do not place the system in an area subject to excessive dust or cigarette

smoke. Dust build-up or cigarette smoke residue on the internal

components (such as the lens) may cause the system to malfunction.



Do not move or change the position of the system while the power indicator

is lit solid green or flashing green. The vibration that occurs as a result of

moving the system may cause data loss or corruption, or damage to the

system.



Some PlayStation

®

and PlayStation

®

2 peripherals such as the analog

controller (DUALSHOCK

®

) and analog controller (DUALSHOCK

®

2) are not

compatible with the PS3™ system. For details, visit www.us.playstation.com.

Hint

When placing the system in a vertical position, use of the vertical stand (sold

separately) is required for stability.

13

Getting started

US

If video is not displayed on the screen

If you change the type of cable used to connect the

system to a TV, video may not appear on the screen. If

video does not appear, turn off the system and then

turn it on again by pressing the power button for at

least five seconds (until the system beeps twice). The

video output setting will be reset and video will be

output at standard definition (SD) resolution.



HDMI OUT

connector

AV MULTI OUT

connector

Connection methods

Caution

Any TV or component connected to the system

must be functioning properly and free of defects. If

a TV or component connected to the system is

faulty or defective, it may cause damage to the TV

or component, or to the system itself. As with all

electrical products, connection to faulty or

defective components, or the failure to connect to a

properly wired outlet, may cause sparking and

pose a fire hazard.



Connect your system to a TV

You can use any of the following methods to connect your system to a TV.

VIDEO L

-

AUDIO

-

R

AV MULTI OUT

connector

AV Cable

TV

HDMI OUT

connector

HDMI Cable (sold separately)

Video output in HD (High Definition) resolution - component video

Y L R

P

R

/C

R

P

B

/C

B

COMPONENT VIDEO IN AUDIO IN

Component AV Cable

(sold separately)

AV MULTI OUT

connector

TV

Video output in HD (High Definition) resolution - HDMI™

Video output in SD (Standard Definition) resolution

Hints



For details about video output cable types and supported video modes, see "Video output on the

PS3™ system" (

page 16) and "Video output cable types" ( page 17).



You can connect audio devices that support digital audio playback, such as an AV receiver for home

entertainment use. For details, see "Connecting digital audio devices" (

page 20).

14

Getting started



Connect an Ethernet cable (sold separately)

Use an Ethernet cable to connect the system to the Internet.

Hint

You can use a wireless network connection to connect to the Internet without using an Ethernet cable.

For details, see "Adjusting network settings" (

page 28).

Caution

Do not connect a standard telephone line or other types of cords or cables that are not compatible

with the system directly to the LAN connector on the system, as this may cause heat build-up, fire

or malfunction.



Connect the AC power cord

After plugging the AC power cord into the electrical outlet, the power indicator on the

PS3™ system will light up in solid red ( page 21).

Caution

Do not plug the AC power cord for the system into an electrical outlet until you have made all other

connections. Make sure the TV or other component is unplugged from the electrical outlet prior to

connecting it to the system.



LAN connector AC IN connector

15

Getting started

US

Performing initial setup of the system software

After turning on the system, perform initial setup.

1 Turn on the TV, and then switch the video input of the TV to

match the input connector used by the PS3™ system.

2 Press the power button.

The power indicator turns green and the picture is displayed on the TV

screen.

Power button

Power indicator

3 Connect the wireless controller to the system using a USB

cable.

4 Press the PS button on the controller.

The system will recognize the controller. After it has recognized the controller,

the initial setup screen will be displayed.

5 Perform initial setup.

Follow the on-screen instructions to enter settings for system language, time

zone, date and time, and user name.

The screen for setting up the Internet connection will be displayed. When

connecting using an Ethernet cable, basic settings will be selected

automatically if you follow the on-screen instructions. When connecting over

a wireless LAN, follow the instructions in "Adjusting network settings

(wireless)" (

page 29) to set up the connection.

After the settings have been completed, the XMB

™

menu (

page 11) will

be displayed on the TV screen.

Hints



When using an HDMI cable to connect the system to the TV, a screen for

changing the video output resolution will be displayed during initial setup. If you

select [Yes] on the screen and then press the

button, the optimal output

resolution will be selected automatically.



For details on entering text, see "Using the on-screen keyboard" (

page 34).



Settings entered during initial setup can be changed under (Settings) or

(Users). For details, refer to the online user’s guide

(http://manuals.playstation.net/document/).

16

Getting started

Video output on the PS3™ system

The PS3™ system can output two types of resolution: HD and SD. Refer to the instruction manual for the TV in use to check which video mode is

supported.

HD

(High Definition)

SD

(Standard Definition)

Video mode *

1

1080p 1080i 720p 480p 480i *

2

Aspect ratio

16:9 16:9 16:9

16:9

4:3

16:9

4:3

*

1

This number indicates the number of scan lines. Note that "i" stands for "interlace" and "p" stands for "progressive". Using progressive results in high-quality video with

minimal flickering.

*

2

The video output setting on the system will display as [Standard (NTSC)].

Screens showing the difference in resolution

HD screen SD screen

17

Getting started

US

Video output cable types

The resolution displayed on the TV varies depending on the input connectors on the TV and the type of cable in use. Select a cable to match the TV

in use.

Cable type Input connector on the TV Supported video modes*¹

HDMI Cable*²

(sold

separately)

HDMI IN connector

1080p / 1080i / 720p / 480p

Component AV Cable

(sold separately)

Component VIDEO IN

connector

Y L RPR/CRPB/CB

COMPONENT VIDEO IN AUDIO IN

1080p / 1080i / 720p / 480p / 480i*

3

S VIDEO Cable

(sold separately)

S VIDEO IN connector

S VIDEO L

-

AUDIO

-

R

480i*

3

AV Cable

(supplied)

VIDEO IN connector

(composite)

VIDEO L

-

AUDIO

-

R

480i*

3

*

1

Depending on the type of TV or content to be played, some video modes may not be supported.

If a device that is not compatible with the HDCP (High-bandwidth Digital Content Protection) standard is connected to the system using an HDMI cable, video and/or

audio cannot be output from the system.

Copyright-protected Blu-ray video discs can only be output at 1080p using an HDMI cable connected to a device that is compatible with the HDCP (Highband-width

Digital Content Protection) standard.

*

2

Connect the system to the TV using an HDMI cable (sold separately). An HDMI cable can output both video and audio and enables you to enjoy digital-quality

video and audio.

*

3

The video output setting on the system will display as [Standard (NTSC)].

18

Getting started

Adjusting video output settings

Depending on the type of cables and the connectors used, you may

need to adjust the PS3™ system's video output settings to display

video at HD resolutions ( page 16) on a TV.

If video is not displayed



Switch the video input of the TV to match the input connector used to

connect to the system.



Turn off the system, and then turn it on again by pressing the power button

for at least five seconds (until the system beeps twice). The video output

setting will be reset and video will be output at standard definition (SD)

resolution.

1 Select (Settings) (Display Settings) [Video Output

Settings], and then press the button.

2 Select the input connector ( page 17) in use on the TV, and

then press the button.

If you select [HDMI], you will have the option to choose [Automatic] or

[Custom] on the next screen. In most cases, select [Automatic], and video

output settings will be completed automatically.

If you select [AV MULTI / SCART], you must choose the type of output signal

on the next screen. In most cases, select [Y Pb/Cb Pr/Cr].

3 Confirm the screen, and then press the button.

If you changed the connector in step 2, a screen for confirming the change

will be displayed.

4 Confirm the settings, select [Yes], and then press the button.

If you changed the connector in step 2, a screen for confirming the settings

will be displayed.

5 Select the resolutions supported by the TV, and then press the

button.

The resolution displayed on the TV varies depending on the input connector

and the type of cable used (

page 17). The highest resolution you

selected will be used for video output.

Depending on the connector selected in step 2, this screen may not be

displayed.

19

Getting started

US

6 Confirm the settings, select [Yes], and then press the button.

Depending on the connector selected in step 2 and the resolutions selected

in step 5, this screen may not be displayed.

7 Select the type of TV, and then press the button.

If you selected [Standard (NTSC)] or [480p] in step 5, a screen for selecting

the TV screen size will be displayed. Adjust the setting to match the TV in use.

If you selected [720p] or a higher resolution in step 5, the TV type will

automatically be set to 16:9 and the screen for selecting the TV screen size

will not be displayed.

8 Confirm the settings, and then press the button.

The video output settings will be saved on the system.

9 Adjust audio output settings.

Continue on to adjust audio output settings. Adjust settings to match the TV

or audio device in use.

If you select [HDMI], you will have the option to choose [Automatic] or

[Manual] on the next screen. In most cases, select [Automatic].

If using a cable other than an HDMI cable to output audio from the TV, select

[Audio Input Connector / SCART / AV MULTI]. If using an optical digital cable

to output audio, select [Digital Out (Optical)] and choose the output format

on the next screen.

10 Confirm the settings, and then press the button.

The audio output settings will be saved on the system.

Hints



You can adjust audio output settings under

(Settings) (Sound

Settings)

[Audio Output Settings].



If the TV in use supports 3D Stereoscopic display, a screen for setting the TV’s

screen resolution will be displayed after step 2. Follow the on-screen

instructions to adjust the settings. Using an HDMI cable, connect the PS3™

system to a TV that supports 3D Stereoscopic display.

20

Getting started

Connecting digital audio devices

You can connect audio devices that support digital audio playback,

such as an AV receiver for home entertainment use.

Audio output on the PS3™ system

The supported channels may vary depending on the output connector

to be used.

PS3™ system output connectors

Channels that can be used for output

2 Ch. 5.1 Ch. 7.1 Ch.

AV MULTI OUT connector

  

DIGITAL OUT (OPTICAL) connector

  

HDMI OUT connector

  

Hints



When connecting a digital audio device to the system, go to

(Settings)

(Sound Settings) [Audio Output Settings], and then adjust the settings as

necessary for the audio device.



For simultaneous audio output from multiple connectors, go to

(Settings)

(Sound Settings) [Audio Multi-Output], and set the option to [On].



The system can output both audio and video through an HDMI cable. If both

the TV and the audio device have HDMI connectors, you can output the TV

picture to the TV through a connected audio device.



If a device is connected to the PS3™ system via an HDMI cable, do not turn off

the device while the system is turned on (power indicator is lit solid green), as

doing so may cause sound distortion or produce abnormal sounds.

Examples when connecting an audio device

An HDMI cable or optical digital cable can be used to connect an

audio device to the PS3™ system.

HDMI cable Optical digital cable

HDMI cable

(sold separately)

Digital audio

device

Optical digital

cable for audio

(sold separately)

Video output cable for the

TV in use (

page 17)

HDMI cable

(sold separately)

TV TV

Digital audio

device

21

Turning the PS3™ system on and off

US

Turning on the system

1 Press the power button.

The power indicator lights up in solid green to indicate that the system is

turned on.

Power indicator:

solid green

Power button

2 Press the PS button on the controller.

After the controller number is assigned, you can use the controller to operate

the system.

PS button

Turning off the system

1 Press the power button.

The power indicator lights up in solid red.

Power indicator:

solid red

Power button

Power indicator status

You can check the power indicator on the PS3™ system to see the

current status of the system.

Solid green

System on

Flashing green

System turning off

Solid red

System off (in standby mode)

Notice

When the power indicator is lit solid green or flashing green, be sure to abide

by the notices below. If you do not, data loss or corruption, or damage to the

system may occur.



Do not unplug the AC power cord from the electrical outlet.



Do not move or change the position of the system.

Hints



Before using a wireless controller, you must first pair it with the system

(

page 22).



You can also turn the PS3™ system on and off using the PS button on the

wireless controller. If you use the PS button to turn on the system, the controller

number will be assigned at the same time. To turn off the system, press the PS

button for more than one second, and then follow the on-screen instructions.



You can also turn off the PS3™ system from the XMB

™

menu. Select

(Users) (Turn Off System).



If you will not be using the system for a long period of time, check that the

power indicator is lit solid red, and then unplug the AC power cord from the

electrical outlet.

Page is loading ...

Playstation 4-198-819-12 User manual

Related papers

Other documents