Form No. 70704A 1/04 CLARKE TECHNOLOGY Printed in the U.S.A.
READ THIS BOOK
This book has important information for the use and safe operation of this machine. Failure to read this
book prior to operating or attempting any service or maintenance procedure to your ALTO machine could
result in injury to you or to other personnel; damage to the machine or to other property could occur as
well. You must have training in the operation of this machine before using it. If your operator(s) cannot
read English, have this manual explained fully before attempting to operate this machine.
Si Ud. o sus operadores no pueden leer el Inglés, se hagan explicar este manual completamente antes
de tratar el manejo o servicio de esta máquina.
All directions given in this book are as seen from the operator’s position at the rear of the machine.
For new books write to: ALTO U.S. Inc., 2100 Highway 265, Springdale, Arkansas 72764.
Operator's Manual
Manual del Operador
Manuel de l'operateur
BEXT
®
-100,
100H, 300HV
Extractor's
230V
Page 2 CLARKE TECHNOLOGY BEXT
®
-100, 100H, 300HV 230V Operator's Manual
CONTENTS OF THIS BOOK
Operator Safety Instructions .................................................................................. 5
Introduction and Machine Specifications ..................................................................6
Controls and Machine Features...............................................................................12
How to Prepare the Machine for Operation ..............................................................14
Set-Up........................................................................................................14
BEXT
®
-100 Control Panel .............................................................................16
BEXT
®
-100H Control Panel...........................................................................18
BEXT
®
-300HV Control Panel ........................................................................18
Instructions for Connection to the Power Supply - 230V
Extension Cords - 230V .............................................................................20
Machine Operating Instructions ...............................................................................22
How to Clean an Area of Carpet..................................................................22
How To clean a Larger Area of Carpet.........................................................22
Maintenance ...........................................................................................................24
After Each Use of the Machine ...................................................................24
How to Prevent Damage from Freezing Temperatures.................................26
The Pump and Vacuum Motor ...................................................................26
How To Check The Commutator and The Carbon Brushes ..........................28
How to Correct Problems in the Machine.................................................................30
BEXT
®
-100 Assembly Drawing .................................................................................34
Parts List ................................................................................................35
BEXT
®
-100H Assembly Drawing ...............................................................................36
Parts List ................................................................................................37
BEXT
®
-300HV Assembly Drawing ............................................................................38
Parts List ................................................................................................39
BEXT
®
-150 Accessories ............................................................................................40
BEXT
®
-100H Accessories .........................................................................................41
BEXT
®
-300HV Accessories.......................................................................................41
BEXT
®
-150/100 Connection Diagram .........................................................................42
BEXT
®
-150/100 Wiring Diagram ................................................................................43
BEXT
®
-150H/100H Connection Diagram ....................................................................44
BEXT
®
-150H/100H Wiring Diagram ............................................................................45
BEXT
®
-300HV Connection Diagram...........................................................................46
BEXT
®
-300HV Wiring Diagram ..................................................................................47
Page is loading ...
Page is loading ...
CLARKE TECHNOLOGY BEXT
®
- 100, 100H, 300HV 230V Operator's Manual Page 5
OPERATOR SAFETY INSTRUCTIONS
WARNING AVERTISSEMENT ADVERTENCIA
For the safe operation of this machine, read and understand all warnings and cautions.
DANGER means: Severe bodily injury or death can occur to you or other personnel if
the DANGER statements found on your machine or in your Owner's
Manual are ignored or are not adhered to. Read and observe all
DANGER statements found in your Owner's Manual and on your
machine.
WARNING means : Injury can occur to you or to other personnel if the WARNING
statements found on your machine or in your Owner's Manual are
ignored or are not adhered to. Read and observe all WARNING
statements found in your Owner's Manual and on your machine.
CAUTION means: Damage can occur to the machine or to other property if the
CAUTION statements found on your machine or in your Owner's
Manual are ignored or not adhered to. Read and observe all
CAUTION statements found in your Owner's Manual and on
your machine.
DANGER: Machines can cause an explosion when operated near flammable materials and vapors. Do not
use this machine with or near fuels, grain dust, solvents, thinners, or other flammable materials.
DANGER: Do not immerse. To reduce the risk of an electric shock, use only on a carpet that has been
moistened by a cleaning process. Protect the machine from rain. Keep the machine in a dry
building. Always clean the machine with a clean dry cloth.
WARNING: You must have training in the operation of this machine before using it. READ THE
INSTRUCTION BOOK FIRST.
WARNING: Always use a three-wire electrical system connected to the electrical ground. For maximum
protection against electric shock, use a circuit that is protected by a ground fault circuit
interrupter. Consult your electrical contractor.
WARNING: To prevent electric shock, always remove the electrical plug from the electrical outlet before
doing any repairs or maintenance to this machine.
WARNING: Do not use this machine as a step or furniture. Injury could occur to the operator.
WARNING: To avoid serious injury, use proper lifting procedures when lifting the machine.
WARNING: Maintenance and repairs must be done by authorized personnel only.
WARNING: Keep all fasteners tight. Keep the adjustments according to specifications.
WARNING: Make sure that all the labels, decals, warnings, cautions and instructions are fastened to the
machine. Replace them when necessary by ordering them from Clarke Technology.
WARNING: Do not use water that is hotter than 120
°
F (40
°
C).
WARNING: If foam/liquid comes out, stop extracting immediately. Allow vacuum('s) to run until exhaust
air is dry.
Page 6 CLARKE TECHNOLOGY BEXT
®
-100, 100H, 300HV 230V Operator's Manual
OPERATOR SAFETY INSTRUCTIONS (CONT.)
WARNING: Improper discharge of waste water may damage the environment and be illegal. The United
States Environmental Protection Agency has established certain regulations regarding dis-
charge of waste water. Also, city and state regulation regarding this discharge may be in effect
in your area. Understand and follow the regulations in your area. Be aware of the environmental
hazards of chemicals that you dispose.
CAUTION: To prevent damage to the power cord, do not move this machine over the power cord, instead,
lift the power cord over the machine. If the cord supplied is damaged, it must be replaced by
the manufacturer, its service agent or a similarly qualifed person in order to avoid the hazard.
CAUTION: To prevent damage to the power cord and hoses, do not use the power cord or hoses to pull
the machine.
CAUTION: To prevent damage to the machine avoid extreme temperatures.
CAUTION: To prevent damage to the machine do not let pump run dry.
Model BEXT
®
-100 BEXT
®
-100H BEXT
®
-300HV
Code Number 04149A 04150A 04151A
Electrical Cord #1 Cord #2 Cord #1 Cord #2
Current (Amps) 9.5 8 8 8 8
Solution Pump Pressure 100 psi 100 psi 300-75 psi
Solution Tank Capacity 13 gallons 13 gallons 13 gallons
Recovery Tank Capacity 11 gallons 11 gallons 11 gallons
Solution Flow per minute .80 gallons .80 gallons .80 gallons
Vacuum Motor Power 2 -1 hp 2 - 1 hp 1
Power Cable Length 25' 25' (2) 25' (2)
Wheels, Number-Diameter 2-10" W 2 - 4"Casters 2-10" W 2 - 4"Casters 2-10" W 2 -4"Casters
Dimensions (LxWxH) 36"L x 16"W x 26.5"H 36"L x 16"W x 26.5"H 36"L x 16"W x 26.5"H
Weight 80 lbs. 90 lbs. 119 lbs.
Shipping Weight 100 lbs. 110 lbs. 150 lbs.
Warranty 1 year (Plus Limited Lifetime)
Sound Level (dBA)
• The Model BEXT
®
-150, 150H or 300HV is an extractor for cleaning carpet. When used with a floor tool, the machine
applies cleaning solution to the carpet and removes the dirty solution and soil from the carpet.
• The extractor has controls to start the pump for the solution and the motor for the vacuum. The floor tools have controls
to release the solution.
• The extractor has a bypass pump. The pump runs when switched on, bypassing solution internally to keep pressure
even.The extractor starts when the solution lever on the floor tool is activated.
NOTE: When using the extractor to clean carpets, follow this procedure:
1. Do not walk on freshly cleaned carpets for at least four hours or until the carpet is dry to touch.
2. Do not remove aluminum or plastic pieces that have been placed under the legs of furniture until
the carpet is dry.
3. Do not allow children or pets to crawl or walk around on the damp carpet.
4. Vacuum right after the carpet is dry and then vacuum the carpet once a week as needed.
INTRODUCTION and MACHINE SPECIFICATIONS
INSPECTION: Carfefully unpack and inspect your new Extractor for shipping damage. Each unit is tested and inspected
before shipment. Any damage incurred is the responsibility of the carrier, who should be notified immediately.
CLEANING SOLUTIONS: We recommend liquid cleaning chemicals. A pH of 7-9 is strongly recommended to avoid
premature pump wear, which would voide the warranty.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
CLARKE TECHNOLOGY BEXT
®
- 100, 100H, 300HV 230V Operator's Manual Page 11
NOTES
Page 12 CLARKE TECHNOLOGY BEXT
®
-100, 100H, 300HV 230V Operator's Manual
CONTROLS and MACHINE FEATURES
The Vacuum Motor Switches See Figure 1-A
The vacuum motor switches are located on the top of the
machine.
The Switch To Activate The Pump See Figure 1-B
The switch to start/stop the pump motor is on the top of the
machine. Press the lever on the floor tool to start the
solution flow. Release the lever on the floor tool to stop the
solution flow.
NOTE: While the BEXT-100 machine is in operation,
the pump will shut-off automatically when it reaches
full pressure. The pump will automatically turn on
when the pressure decreases.
The Float Shut-Off -See Figure 1C
The float shut-off is in the recovery tank. When the liquid
raises the float, the air stops moving through the machine.
NOTE: To avoid vacuum motor damage, always
inspect the float filter and ball. Verify ball travels
easily prior to use of unit. See Figure 2
The Vacuum Hose Connector See figure 1D
The vacuum hose connector is on the front of the unit.
The Solution Hose Connector See Figure 1E
The solution hose connector is on the lower part of the
extractor, below the vacuum hose connector.
The Recovery Tank See Figure 1F
The recovery tank is in the top of the machine.
The Solution Tank See Figure 1G
The solution tank is in the top of the machine next to the
recovery tank.
The Machine Power Cord (Red Band) See Figure 1I
This cord powers all machine functions except the heater.
The Heater Power Cord See Figure 1J
This cord powers heater only.
Figure 2
Figure 1
1G
1B
1A
1C
1F
1E
1D
Figure 1
1I
1J
Page is loading ...
Page 14 CLARKE TECHNOLOGY BEXT
®
-100, 100H, 300HV 230V Operator's Manual
HOW TO PREPARE THE MACHINE FOR OPERATION
To prepare the machine for operation, follow this proce-
dure:
1. Connect the vacuum hose to the hose connector
on the extractor and to the end of the vacuum tube
on the floor tool. See Figure 1 D, E
2. Connect the solution hose to the extractor and the
floor tool. To fasten the quick disconnect fitting,
slide the knurled collar on the female coupling
away from the opening. Push the male coupling
into the female coupling. See figure 3 A & B
WARNING: Do not use water that is hotter than
120°F (48°C).
3. Before moving the extractor onto the carpet, put
clean hot water into the solution tank.
4. Add a cleaning chemical, such as Clarkare
®
Extrac-
tor Concentrate, to the hot water. For the correct
amount, follow the directions shown on the con-
tainer.
Set-Up
WARNING: We recommend that you use liquied
cleaning chemicals. Powder can dam-
age machine. Powders can cause
build-up in the lines, heater, pump,
quick disconnects, etc., all of which
would void the warranty on those items.
A pH of 7-9 is strongly recommended
to avoid damage and premature wear
to the pump, which would void the
warranty.
Fill the holding tank with clear water and the detergent of your
choice. Mix well. Although this machine is designed to
supply instant hot water, the addition of warm or hot water to
the holding tank is beneficial and will reduce pre-heat times..
A. Plug in cord #1 (vac and pump), identified by the 4" long
red band on the end of the cord. Attach the priming hose
to the machine (on 300 HV only). Turn the pump on and
set the switch to the upholstery setting. Run until the
pump is fully primed, then turn off the pump. Remove the
priming hose and attach the cleaning hoses and tool.
B. Turn on the pump and spray through the cleaning tool for
a few seconds to fill the lines with solution.
BEXT
®
100H & 300HV
C. Plug in cord #2. Turn the "Heat" switch on; wait two
minutes for the heat exchanger to reach operating tem-
perature. You may now begin cleaning. It will take about
10 seconds for the initial heat to reach the wand. The
"Mode" light will turn on when the heat exchanger is
actively heating. (See Figure 5 on next page 8)
CAUTION: If both cords are plugged into the same
circuit breaker, the breaker may blow
when operating with the heater on.
Figure 3A
Figure 3B
Page is loading ...
Page 16 CLARKE TECHNOLOGY BEXT
®
-100, 100H, 300HV 230V Operator's Manual
NOTE: To order Clarkare
®
Extractor Concentrate, order
part no. 398421. To order Clarkare
®
Defoamer,
order part no. 398420.
For instructions for preparation and operation of your floor
tool, read the instruction sheet given with your floor tool.
5. If the extractor removes an excess amount of foam
from the carpet, add a de-foamer such as Clarkare
®
De-foamer Concentrate to the recovery tank. The
amount needed will vary according to the amount
of detergent already in the carpet.
CAUTION: To prevent damage, use a water-based
de-foamer rather than an oil-based de-
foamer.
CAUTION: Do not leave the extractor or other
cleaning machines or tools on the car-
pet when not in use. Cleaning solution
in the machines and tools can leak onto
the carpet and cause light spots or
stains.
1
23
VAC 1 VAC 2 PUMP
VACUUM SWITCH (1 &2): Each switch turns on one
vac motor. Turn both switches on for maximum lift.
The vac switches illuminate when turned on.
PUMP SWITCH (3): This switch will illuminate when
the pump is on.
Figure 4
BEXT
®
-100
Control Panel
Page is loading ...
Page 18 CLARKE TECHNOLOGY BEXT
®
-100, 100H, 300HV 230V Operator's Manual
1
2
3
VAC
PUMP
VAC ( 1 ) & PUMP ( 2 ) SWITCHES: These switches are powered
by cord #1 (4" red band). Switches are on when illuminated.
CARPET / UPHOLSTERY SWITCH (3): This switch is also pow-
ered by cord #1 (4" red band). The carpet setting (down position)
is high pressure (approximately 300 psi). The upholstery setting
(up position) is low pressure (approximately 75 psi). NOTE:
Switch does not illuminate.
HEAT SWITCH ( 4): Turning on this switch (switch illuminates
when on) turns the heater on.
HEAT LIGHT MODE ( 5 ) : The light will only illuminate when the
heater uis heating and will turn off when it reaches operating
temperature.
Figure 6
4
HEAT
MODE
5
CARPET
2
3
4
VAC 1 VAC 2
PUMP
HEAT MODE LIGHT ( 1 ): This light will only illuminate when the
heater is heating and will turn off when it reaches operating
temperature.
VACUUM SWITCH ( 2 & 3): Each switch turns on one vac motor.
turn both switches on for maximum lift. The vac switches
illuminate when turned on.
PUMP SWITCH ( 4 ): This switch will illuminate when the pump
is on.
HEAT SWITCH ( 5 ) : The heat switch will illuminate when it is
activated and will turn the heater on.
Figure 5
5
HEAT
MODE
1
BEXT
®
-100 H
Control Panel
Upholstery
BEXT
®
-300 HV
Control Panel
Page is loading ...
Page 20 CLARKE TECHNOLOGY BEXT
®
-100, 100H, 300HV 230V Operator's Manual
INSTRUCTIONS FOR CONNECTION TO THE
POWER SUPPLY AND ELECTRICAL GROUND -
230 V
CAUTION: This machine will operate only on
an AC frequency and on the speci-
fied electrical voltage shown on
the nameplate. Make sure you
have the correct frequency and
voltage before connecting the
power cord to an outlet.
This machine must be connected to an electrically
grounded circuit in order to protect the operator from
electric shock. This machine has an approved power
cord with three conductors as well as a plug with three
terminals. Connect the plug to a three holed receptacle.
For maximum protection against electric shock, use a
circuit that is protected by a ground fault circuit inter-
rupter.
This machine uses a 230 volt AC 50/60 cycle electrical
circuit. Make sure you have the correct frequency and
voltage before connecting the power cord to an outlet. The
machine has a plug as shown in Figure 7. If a receptacle
connected to the electrical ground as shown in Figure 7
is not available, contact an electrical contractor. Do not
use an adapter.
WARNING: To prevent possible electric shock,
protect the machine from rain.
Keep the machine in a dry build-
ing.
WARNING: To prevent possible electric shock,
always use a 3-wire electrical sys-
tem connected to the electrical
ground. For maximum protection
against electrical shock, use a cir-
cuit that is protected by a ground
fault circuit interrupter. Consult
your electrical contractor.
WARNING: If the cords or plugs are worn or
damaged in any way, have them
replaced by an authorized service
person.
Extension Cords
Use only an approved extension cord with three conduc-
tors, a plug with three terminals and a three-holed
connector body. This machine has a power cord with a
wire size of 12 AWG. (AWG stands for American Wire
Gauge).
CAUTION: If you use an extension cord, use
one that has a minimum wire size
of 12 AWG. Be sure your extension
cord is no longer than 50 ft. Do not
join two extension cords.
Figure 7
Pin Earthing Contact
European Plug
Side Earthing Contact
Figura 7
Clavija de contacto de
conexión a tierra
Enchufe europeo
Contacto lateral de
conexión a tierra
Figure 7
Lamelle de mise à la
masse
Prise européenne
Contact latéral de
mise à la masse
Page is loading ...
Page 22 CLARKE TECHNOLOGY BEXT
®
-100, 100H, 300HV 230V Operator's Manual
MACHINE OPERATING INSTRUCTIONS
How to Clean an Area of Carpet See Figure 8A
WARNING: Do not use water that is hotter
than 120°F (48°C).
To clean an area of carpet, follow this procedure:
1. Start the pump for the solution and the motor for the
vacuum on the extractor.
2. Begin at the right-hand corner of the carpet.
3. Hold the floor tool at the angle that gives the best
vacuum seal between the tool and the carpet.
4. Apply pressure to the lever for solution release. Pull
the tool toward you at a slow, steady speed. To
remove as much solution as possible, release the
lever before you stop moving backward. Push tool
away over the same area while moving tool to next
position. (Repeat process)
5. To clean the edge of a room, move the tool along the
baseboard until the edge of all the carpet is cleaned.
6. To clean a small area of carpet, clean the carpet in
sections three feet square. As you make more
passes, repeat one inch of the area already cleaned.
7. To remove more liquid from the carpet, make passes
over the area already cleaned, but do not apply
pressure to the lever for the solution.
How To Clean A Larger Area Of Carpet See Fig. 8B
To clean a larger area of carpet, follow this procedure:
1. Begin at the right-hand corner of the carpet.
2. Make a pass halfway along the edge of the carpet.
Pull the tool backward at a steady speed.
3. Move to the edge of the carpet. Make another pass
next to your first pass.
4. As you make more passes, repeat one inch of the
area already cleaned. If you use a power brush tool,
repeat one inch of the area already cleaned by the
brush. Make each pass four inches different in length
to prevent making a line in the center of the carpet.
5. Make more passes until half of the carpet is cleaned.
To remove more liquid from the carpet, make passes
over the area already cleaned, but do not apply
pressure to the lever for the solution.
6. Move to the right-hand corner of the part of the carpet
not yet cleaned.
7. Make a pass halfway along the edge of the carpet.
8. As you make passes, repeat one inch of the area
already cleaned.
9. Make more passes until all of the room is cleaned.
CAUTION: ALTO U.S. (CLARKE TECHNOLOGY) will
not be held liable for damage to the car-
pet, or poor results because of the
operator's lack of ability.
Figure 8A
Figure 8B
Vacuum only,
after cleaning
each area for
maximum
water removal
Area 1 See figure 8
Superficie 1. Vea la Figura 8
Zone 1 Voir figure 8
Para eliminar
la mayor
cantidad de
agua posible
sólo realice la
aspiración
después de
limpiar cada
superficie
Aspiration
seulement,
après nettoyage
de chaque zone
pour une
élimination
maximum de
l'eau
Page is loading ...
Page 24 CLARKE TECHNOLOGY BEXT
®
-100, 100H, 300HV 230V Operator's Manual
MAINTENANCE
WARNING:Maintenance and repairs must be
done by authorized personnel
only. Keep all fasteners tight.
Use only genuine Clarke Tech-
nology parts.
WARNING: Do not operate this machine un-
less it is completely assembled.
NOTE: For maintenance of the floor tools read the
manual given with the tools.
After Each Use of the Machine
1. Remove unused cleaning solution from the solu-
tion tank, by placing the end of the vacuum hose
in the solution tank. Start the vacuum motor.
Stop the motor when the tank is empty.
2. To prevent damage to the valves and jets, flush
one gallon of clean water through the solution
system and the tools.
3. Disconnect the power cord from the outlet.
4. For optimum performance, flush the machine with
clear water at the end of each working day. Once
a month, minimum, run a flushing compound
through the machine to cut any alkaline build-up
that may have formed.
5. Lubricate wheels, casters, and hinges as needed.
The pump and vacuum motor do not require any
maintenance.
6. The body can be cleaned with a general all-
purpose detergent and protected with a silicone
type product. The quick-disconnects should be
lubricated with silicone, also.
7. Prior to each job, inspect the holding tank filter
and the recovery tank float filter for hair and dirt.
The drain valve should also be inspected regularly
and kept free of any debris or build-up.
8. Drain the recovery tank and dispose of properly.
9. Rinse the recovery tank with clean water.
10. Use a dry cloth to wipe the tools and both tanks,
inside and out.
11. Apply a small amount of silicone lubricant to the
quick-disconnect fittings. To prevent damage to
the O-rings, do not use an oil lubricant.
12. Clean and inspect the gasket on the vacuum
shut-off valve. If the gasket is damaged, replace
the gasket.
Page is loading ...
Page 26 CLARKE TECHNOLOGY BEXT
®
-100, 100H, 300HV 230V Operator's Manual
MAINTENANCE (CONT)
How To Prevent Damage From Freezing Tempera-
tures
To prevent damage from freezing temperatures follow
this procedure:
1. Use the vacuum hose to remove all the solution
from the clean solution tank.
2. Connect the solution hose to the extractor and a
floor tool.
3. Put approximately 1 quart of antifreeze solution in
the solution tank.
4. Put the switch for the pump in the "ON" position.
5. Put the end of the floor tool in the recovery pail.
6. Press the lever on the floor tool to activate the
pump.
7. Make sure the solution runs through the system.
8. Release the lever on the floor tool to stop the
pump.
9. Flush the antifreeze solution from the system
before using the extractor.
WARNING: Electrical repairs must be done by
authorized personnel only.
WARNING: After electrical repairs are done to
the machine, the machine must be
tested for electrical safety.
How To Get Access To The Pump and Vacuum
Motor
To get access to the pump and the vacuum motor,
follow this procedure (see figures 9a & 9b):
1. Empty both tanks.
2. Unlatch tanks from base.
3. Tilt tanks back.
4. Disconnect hoses from tanks.
5. Open up for service.
Figure 9b
Figure 9a
Page is loading ...
Page 28 CLARKE TECHNOLOGY BEXT
®
-100, 100H, 300HV 230V Operator's Manual
Maintenance Of The Motor
This machine has a vacuum motor that uses carbon
brushes. The carbon brushes in the motor must be
checked every three months, or every 500 hours of
operation, whichever comes first. If either of the brushes
is shorter than 3/8 inch, replace both of the carbon
brushes.
How To Check The Commutator And The Carbon
Brushes
WARNING: Electrical inspections must be made
by a person authorized to make
electrical repairs.
To check the commutator and the carbon brushes follow
this procedure:
1. Disconnect the power cord from the electrical outlet.
2. Empty both tanks.
3. Unlatch tanks from lower housing.
4. Lift the upper housing from the lower housing.
5. Disconnect the ground wire.
6. Remove the plastic motor cover.
7. Inspect the commutator. See figure 10. Take the
machine to a Clarke Technology authorized repair
location if you see any of the following conditions:
a.Small holes in the surface of the commutator.
See "A" in figure 11.
b.Uneven color. Look for an even dark brown
color. Clean areas or very dark areas indicate a
problem.
See "B" in figure 11.
c. High mica. The mica insulation must be lower
than the commutator bars. See "C" in figure 11.
8. To check the carbon brush assemblies, remove the
two screws from the holding bracket.
9. Remove the brackets.
10. Remove the carbon brush assemblies.
11. Check the carbon brush assembly. Replace both
carbon brush assemblies if either carbon brush is
shorter than
3
/8 inch. If either brush is shorter than ½
inch, order replacement brushes. Be ready to
replace both carbon brushes earlier than the
normal inspection time.
12. Put the motor brushes in position.
13. Using the two screws, install the bracket that holds
the carbon brushes.
14. Install the plastic motor cover.
15. Connect the ground wire.
16. Install the motor holding bracket.
17. Install the lower housing to the upper housing.
Figure 10
UNEVEN
GOOD
SMALL
HOLES
GOOD
GOOD
HIGH MICA
C
AB
MAINTENANCE (CONT)
INÉGAL
CORRECT
PETITS TROUS
CORRECT
CORRECT
MICA ÉLEVÉ
C
AB
IRREGULAR
EN BUEN
ESTADO
AGUJEROS
PEQUEÑOS
EN BUEN
ESTADO
EN BUEN
ESTADO
MICA ALTA
C
AB
Page is loading ...
Page 30 CLARKE TECHNOLOGY BEXT
®
-100, 100H, 300HV 230V Operator's Manual
HOW TO CORRECT PROBLEMS IN THE MACHINE
ActionCause
Problem
1. Make sure the machine is connected to the
correct frequency and voltage, and all connec-
tions are tight.
Make sure the plug is in the electrical outlet.
2. Contact an authorized service person to replace
the cord.
1. Put the switch for the vacuum in the "I" position.
2. Contact an authorized service person.
3. Contact an authorized service person.
4. Remove the obstruction.
5. Remove the liquid from the tank.
6. Contact an authorized service person to re-
place gasket.
7. Contact an authorized service person.
8. Replace the dome.
9. Replace the motor brushes.
10. Close drain gate.
11.Contact an authorized service person.
1. Put the switch in the "I" position.
2. Contact an authorized service person.
3. Contact an authorized service person.
4. Contact an authorized service person.
5. Contact an authorized service person.
6. Straighten the hose. Replace if damaged.
7. Contact an authorized service person.
8. Contact an authorized service person.
9. Contact an authorized service person.
10.Contact an authorized service person.
11.Contact an authorized service person.
12.Fill the solution tank.
13.Clean the screen.
14.Contact an authorized service person.
1. Contact an authorized service person.
1. Clean the float. Replace if damaged.
2. Put defoamer in the solution. Order P/N 398420.
3. Clean the gasket. Replace if damaged.
1. The machine has no power.
2. The power cord is damaged.
1. The vac motor does not run.
2. The vac motor switch is defective.
3. There is a loose motor connection.
4. There is an obstruction in the vacuum
hose.
5. The recovery tank is full.
6. The dome gasket is worn or damaged.
7. The internal vac hose is damaged
or stopped.
8. The dome is damaged
9. The motor brushes are worn.
10. Drain gate is open.
11.Seals are damaged.
1. The switch is in the "OFF" position.
2. The pressure switch is damaged.
3. The pump motor will not run.
4. The pump motor brushes are worn.
5. The quick disconnect fitting is dirty
or stopped.
6. The solution hose is bent.
7. The pump is worn.
8. The pump switch is defective.
9. The pump connections are loose.
10.The pump intake and oulet valves are
worn.
11.The thermal protector is open.
12.The solution tank is empty.
13.The intake screen is dirty.
14.The rectifier in the pump motor is bad.
1. The tank is damaged.
1. The float is dirty or damaged.
2. There is too much foam.
3. The float gasket is dirty or damaged.
The machine will not run.
There is no suction.
There is no pressure.
The solution tank leaks.
The recovery tank overflows.
Page is loading ...
Page is loading ...
CLARKE TECHNOLOGY BEXT
®
- 100, 100H, 300HV 230V Operator's Manual Page 33
230V
BEXT
®
-100, 100H, 300HV
Extractor
Section II
Parts and Service Manual
(70704A)
Page 34 CLARKE TECHNOLOGY BEXT
®
-100, 100H, 300HV 230V Operator's Manual
CLARKE TECHNOLOGY BEXT
®
-100 230V
Assembly Drawing 2/03
31
30
62
65
64
63
32
16
16A
21
46
44
17
35
53
51
55
54
51
54
51
36
48
51
56
52
33
14
24
67
23
22
21
20
21
26
25
14
15A
22
21
20
21
26
25
71
1A
1
4
6
24
9
9A
8
8A
10A
10
45
34
39
41
38
39A
38A
4
40
2
3
4A
70
7
14
4A
13
15
59
59
59
5
47
51A
68
8
61
49
50
57
58
23
37
4
CLARKE TECHNOLOGY BEXT
®
- 100, 100H, 300HV 230V Operator's Manual Page 35
CLARKE TECHNOLOGY BEXT
®
-100 230V
Assembly Drawing Parts List 9/03
Ref # Part No. Description Qty
1 59721A Valve-Drain 1
1A 53606A Elbow-45 Degree, Drain 1
2 962929 Screw, 10-32 x 3/8 4
3 52636A Latch, Recovery Tank 1
4 837304 O-Ring 3
4A 920797 Nut Drain Valve Lock 3
5 30322A Tank, Recovery 1
*6 690212 Adaptor Asm.-Vac Hose 1
*7 692701 Elbow - 90 Degree 2
8 55674A Lid 6" Clear 1
8A 692409 Chain-Cover 1
9 85613A Screw, 8-32 x 7/8 Pan Hd 6
9A 81109A Nut, Hex Elastic Lock 6
10 52806A Vac Manifold Asm. 1
(includes 10, 11, 12, 13)
11
12
13 30323A Elbow, Vac Manifold 1
14 872010 Hose Clamp 5
15 52666A Hose Vacuum 1
15A 52667A Hose, Vacuum 1
16 52993A Fiber Washer 1
16A 52992A Washer, Brass 1
17 697501 Adapter, 1/8 ro 1/4 NPT 1
18
19
20 87026A Washer 6
21 81102A Nut, Stop, Elastic ¼-20 18
22 44906A Motor, Vacuum 2
23 30197A Gasket 2
24 52670A Vacuum Manifold 1
25 81102A Screw, ¼-20 6
26 87026A Washer ¼ 8
27
28
29
30 52671A Handle, Lifting 1
31 962098 Screw, Flathead ¼" -20 x ¾ 1
32 737140 Quick Disconnect, Male 1
33 52672A Flange, Exhaust 1
34 52673A Louver, Vent 3
Ref # Part No. Description Qty
35 52674A Latch, Strike 2
36 170040 Elbow, ¼ NPT 1
37 52675A PVC Reducer 1
38 52676A Cord Retainer 1
38A 40637A Power Cord 1
39 61338A Axle, ½" x 3½" 1
39A 61339A Hinge Pin 2
40 52471A Wheel 10" 2
41 920346 Axle Cap 2
42
43
44 170915 Screw, ¼-20 x ¾ 8
45 30324A Housing, Lower 1
46 52470A Castor, 4" Grey 1
47 30195A Tank, Solution 1
48 55167A Hosebarb 3/8 x 1/4 NPT 1
49 52841A Inlet Filter 1
50 30325A Lid, Solution Tank 1
51 50248A Clamp 4
51A 52677A Adaptor, Inlet Screen 1
52 51206A Pump, Solution 150 psi 1
53 Screw, 10-32 x 5/8
54 170030 Hosebarb. 3/8H x 1/4MPT 2
55 30326A Hose, Inlet 1
56 30327A Hose, Outlet 1
57 61340A Switch Plate 1
58 Screw. #4 x 3/8 S.S. Pn Phillips 5
59 52842A Switch, Pump & Vac Motors 3
60 170030 Hosebarb 1
61 52679A Cord Wrap 2
62 Screw, 6-32 x 2.0 Phillips S.S. 4
63 920056 Nut - 6x32 Elastic Stop 4
64 40639A Cooling Fan 1
65 52680A Fan Guard 1
66
67 30196A Gasket, Tank to Base 1
68 962454 Screw, ¼ -20 x 1 2
69
*70 693406 Gasket 1
71 34288A Gasket, Rec. Lid 1
* Items 6, 7 & 70 must be ordered as a set when
replacing any original #6 Adapter and
3 - 85522A Screws
1 - 962109 Screw
1 - 920296 Nut
Page 36 CLARKE TECHNOLOGY BEXT
®
-100, 100H, 300HV 230V Operator's Manual
CLARKE TECHNOLOGY BEXT
®
-100H 230V
Assembly Drawing 2/03
8A
8
4
12
13
15
14
4
4
1
1A
9
9A
8A
7
86
34
6
5
71
72
71
69
74
73
10A
10
22
21
20A
20
24A
24
19
17
23
16
16A
14
15A
27
27
26
25
28
29
26
31
30
28
26
25
26
31
32
29
68
61
61
61
63
63
61
67
60
58
59
57
83
84
25
33
2
3
52
46
47
53
48
49
50
51
42
55
82
42
42
45
41
14
43
44
4020
20A
80
79
77
78
38
39
26
56
CLARKE TECHNOLOGY BEXT
®
- 100, 100H, 300HV 230V Operator's Manual Page 37
CLARKE TECHNOLOGY BEXT
®
-100H 230V
Parts List 9/03
Ref # Part No. Description Qty
1 59721A Valve-Drain 1
1A 53606A Elbow-45 Degree, Drain 1
2 962929 Screw, 10-32 x
3
/8 1
3 52636A Latch 2
4 837304 O-Ring (Small) 3
4B 920797 Nut Drain Valve Lock 2
5 30322A Tank, Recovery 1
*6 690212 Adaptor Asm.-Vac Hose 1
*7 692701 Elbow - 90 Degree 1
8 55674A Lid 6" Clear 1
8A 34288A Gasket** 1
8B 692409 Chain-Cover 1
9 85613A Screw, 8-32 x
7
/8 Pan Hd 1
9A 81109A Nut, Hex Elastic Lock 1
10 52806A Vac Manifold Asm. (incl. 10, 10A, 1
4, 12, 13)
11
12
13 30323A Elbow, Vac Manifold 1
14 872010 Hose clamp 1
15 52666A Hose Vacuum Tank 1
15A 52667A Hose, Vacuum to Manifold 1
16 52566A Heater, Complete 1
16A 732870 Hosebarb 1
17 52365A Hose Clamp 1
18
19 30323A Hose, Braided Heater 1
20 52992A Washer, Brass 1
20A 52993A Washer, Fiber 1
21
22 52995A Bushing, Fiber 1
23 52834A Thermostat, Heater 1
24 53639A Elbow, Brass, ¼ NPT (Female) 1
24A Coupling 1
25 87026A Washer ¼ 6
26 81102A Nut, Stop, Elastic ¼ -20 6
27 44906A Motor, Vac 2
28 30197A Gasket, Vac Motor 2
29 52670A Vacuum, Manifold 2
30 85742A Screw, ¼-20 6
31 87026A Washer 6
32
33 170030 Hosebarb 1
34 52665A Label, ALTO 1
35
36
37
38 52671A Handle, Lifting 1
* Items 6, 7 & 86 must be ordered as a set when
replacing any original #6 Adapter and
3 - 85522A Screws
1 - 962109 Screw
1 - 920296 Nut
** Item 8A must be used with any lid replacement.
Ref # Part No. Description Qty
39 962098 Screw, ¼ - 20 x
3
/4 1
40 52840A Quick Disconnect 1
41 52672A Flange, Exhaust- Flange 1
42 52673A Louvre, (includes hardware) 3
43 52674A Strike, Latch 2
44 Screw, 10-32 x ,
5
/8 Socket 4
45 52675A Reducer, PVC 2
46 52676A Retainer, Cord 2
47 52637A Sensor, Dual Cord 1
48 52664A Snap Track, 4" 1
49 61338A Axle, Wheel 1
50 52471A Wheel, 10" 1
51 920346 Axle, Cap 2
52 40637A Cord, Power 1
53 61339A Pin, Hinge 2
54 170915 Screw, ¼-20 x
3
/4 8
55 30324A Housing, Lower 1
56 52470A Castor, 4" Grey 2
57 30195A Tank, Solution 1
58 52841A Filter, Inlet 1
59 52677A Adaptor, Inlet Screen 1
60 30325A Lid, Solution Tank 1
61 50248A Hose Clamp 1
62 51206A Pump, Solution 1
63 53616A Elbow,
3
/8 x
3
/8 NPT 2
64
65
66
67 30326A Hose, Inlet 1
68 30327A Hose, Outlet 1
69 52678A Switch Plate 1
70
71 52668A Light, Green 2
72
73 52842A Switch, Vacuum / Pump 3
74 52843A Switch, HEAT 1
75
76
77 Screw, #6 -32 x 2.0 4
78 Locknut, #6 4
79 40639A Cooling Fan 1
80 52680A Fan Guard 1
81
82 30196A Gasket, Base 1
83 52679A Cord Wrap 2
84 962454 Screw, ¼-20 x 1 2
85
*86 693406 Gasket 1
Part # Miscellaneous Assemblies/ Parts
52847A
Heat Repair Kit w/ Thermostat and Cutout Asm.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
Alto Bext 300HV User manual
- Category
- Space heaters
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- français: Alto Bext 300HV Manuel utilisateur
- español: Alto Bext 300HV Manual de usuario