JB Systems Light LED ROPE Owner's manual

Version: 1.1

WWW.BEGLEC.COM

Reproduction or publication of the content in any manner, without express permission of the publisher, is prohibited.

LED Rope

Light

Operation Manual

Mode d'emploi

Gebruiksaanwijzing

Bedienungsanleitung

Manual de instrucciones

EN

FR

NL

DU

ES

EN - DISPOSAL OF THE DEVICE

Dispose of the unit and used batteries in an environment friendly manner

according to your country regulations.

FR - DÉCLASSER L’APPAREIL

Débarrassez-vous de l’appareil et des piles usagées de manière écologique

Conformément aux dispositions légales de votre pays.

NL - VERWIJDEREN VAN HET APPARAAT

Verwijder het toestel en de gebruikte batterijen op een milieuvriendelijke

manier conform de in uw land geldende voorschriften.

DU - ENTSORGUNG DES GERÄTS

Entsorgen Sie das Gerät und die Batterien auf umweltfreundliche Art und

Weise gemäß den Vorschriften Ihres Landes.

ES - DESHACERSE DEL APARATO

Reciclar el aparato y pilas usadas de forma ecologica conforme a las

disposiciones legales de su pais.

PT - COMO DESFAZER-SE DA UNIDADE

Tente reciclar a unidade e as pilhas usadas respeitando o ambiente e em

conformidade com as normas vigentes no seu país.

ENGLISH OPERATION MANUAL

JB SYSTEMS

®

1/25 LED ROPE LIGHT

Thank you for buying this JB Systems

®

product. To take full advantage of all possibilities and for your own safety, please

read these operatinginstructions verycarefully before you start using thisunit.

FEATURES

This product meets the requirements of the current European and national guidelines. Conformity has been established

and the relevant statements anddocuments havebeen deposited by themanufacturer.

 This device hasbeen designed toproduce decorative effect lightingand is used in light show systems.

 RGB Multicolorflexible ropelight (round, D=14mm) withsuper bright LEDs inside.

 Perfect forindoor and outdoormulticolor façade decorationof bars, discotheques, shops, …

 Can be bended to follow the shape of walls andcorners.

 Solid 4pinconnectorswith security lock.

 To be used with our LED-MANAGER (dmxpower supply)

 Comes in 30 mlengths that can be cutevery 50cm.

 Lowpowerconsumption: 2 Watt/meter

 Power cables, middle connectors, end capsand mounting clips separately available.

Importantremark : The led rope does only work in cooperation with a separate device, the LED MANAGER (to control

the rope light by DMX). It’s impossible to use the led rope light separately.

BEFORE USE

 Before you start using this unit,please check if there’s no transportation damage. Shouldthere be any, do not use the

device and consult yourdealer first.

 Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary for the user to

strictly follow the safety instructions and warnings in this user manual. Any damage caused by mishandling is not

subject to warranty. The dealer will not accept responsibility for any resulting defects or problems caused by

disregardingthisuser manual.

 Keep this booklet in a safe place for future consultation.If yousell the fixture, be sure to addthis user manual.

Check thecontents:

Check that the carton contains the followingitems:

 Operatinginstructions

 30m Ledrope light

INSTALLING THE LED ROPE LIGHT AND ACCESSORIES

SOME IMPORTANT REMARKS:

 With all LEDs switched on, thisrope lightconsumes about 2 Watts/meter. This means you can connect up to 150m on

1 LED MANAGER (75m on each output: 2x 75m = 150m)

 The rope light canbe cut every 50cm (cutting marks available)

 This product can be used inindoor and outdoor situations, the maximum ambient temperature is 45°C.

!!This LED RGBrope lightcan only be used together with theJB SYSTEMS

®

LED MANAGER !!

!!!DON’T CONNECT DIRECTLY TO230 Vac!!!

Don’t use lengths over 30m, theinternal conductors willbe overloaded which will damage therope light!! (

more infobelow )

ENGLISH OPERATION MANUAL

JB SYSTEMS

®

2/25 LED ROPE LIGHT

SOME ACCESSORIES EXPLAINED:

 POWER CABLE: this power cable is used to connect the rope light to the LED MANAGER. This can be done by

simplyconnecting the conductorsof the powercable with the coloredconductors ofthe cables delivered with the LED

MANAGER.

 MIDDLECONNECTOR:

Used to link 2pieces of LED RGB rope light together.

 ENDCAP: Used to seal the end of a rope light.

 MOUNTING TRACKS (2m): Used to guide the rope light when it is installed on a flat surface. You will be come a

nicely aligned straightrope light.

ENGLISH OPERATION MANUAL

JB SYSTEMS

®

3/25 LED ROPE LIGHT

INSTALLING THE LED ROPE LIGHT:

You can installthe rope light easily on any surface, we suggest using the optional mounting tracks. Do NOT use lengths

over 30m, this may damage the internal conductors! When you have to install lengths over 30m, just split up the

installation in several individual lengths. With a sharp cutting device (very sharphobby knife or wire cutter) you can easily

cut the rope light on the cutting marks ( scissor symbol every 50cm) to split it up in several parts. See “how to make a

length of over 30m” for more info!

1.

2. CUT THE CABLE ATA SCISSORSYMBOL

3. WHEN YOU CONNECT WITH THE POWER CABLE, ALWAYS MAKE SURE THAT THE 24V

SIGN ON THE CABLEIS ON YOUR RIGHT

HOW TO MAKE A LENGTH OF OVER 30M ?

This is an example for 2 pieces with a combined length of 50m.

1. 24 VPower LED rope

2. LED Manager cable assembly

3. 4 conductorcable

4. 24 VPowercable

INSTALLING THE MOUNTING TRACKS:

Use a small hacksaw to cut the mounting tracks to the desired lengths. You can fix them to the surface using strong glue

or small screws. When all tracks are in place youjust have to press the ropelight in the mounting tracks. Done!

LINKING 2 LED ROPE LIGHTS:

Remove the sealing rings on both sides of the middle connector and push the sealing rings over the 2 rope light ends.

Press the 4sharppins of themiddle connectorin the 4conductor holes of 1rope light.

Attention: the holes and pins are a little out of the center, make sure to insert the pins in the right way and push the

middle connector as far aspossible on the rope light! Put the sealingring back in place and tighten it well. Do exactly the

same thing withthe other ropelight end. Ready!

ENGLISH OPERATION MANUAL

JB SYSTEMS

®

4/25 LED ROPE LIGHT

INSTALLING THE POWER CABLE:

The power cable comes together with a rope light connector that must be installed on the rope light first. Refer to the

pictures 1 and 2below.

Attention: the holes and pins are a little out of the center, make sure to insert the pins in the right way and push the

connector from the power cable as far as possible on the rope light! Put the sealing ring back in place and tighten it well.

Ready!

1. 2.

Strip the other end of the power cable and connect it to one of the two small cable assemblies that came with the led

manager. Referto picture 3 for the corresponding colours ofthe wires!

3.

INSTALLING THE END CAP:

The end of the rope light must be sealed. To make it waterproof you must put some silicon on the inside of the cap

before you press it onthe ropelight.

ENGLISH OPERATION MANUAL

JB SYSTEMS

®

5/25 LED ROPE LIGHT

CONNECTING 2 ROPE LIGHTS TROUGH A CABLE:

When you want to connect 2 led ropes trough a piece of cable, you put 2 power cables to each other. You do this as

shown below ( watch the color code + ropemarkings ! ) :

Blue Blauw/Bleu/Blau/Azul

Brown Bruin/Brun/Braun/Marrón/Marrom

Yellow-green Geel-groen/Jaune-vert/Gelb-grün/Amarillo-verde/Amarelo-verde

Black Zwart/Noir/Schwarz/Negro/Preto

OPERATING INSTRUCTIONS

 Onceconnected tothe LEDMANAGER the devicestarts running.

 Inthe event of serious operating problems, stop using thefixture and contact yourdealer immediately.

 Important: Never look directly into the light source! Don’t use the effect in the presence of persons suffering from

epilepsy.

MAINTENANCE

 Make sure the area below the installationplaceis free from unwanted persons during servicing.

 Switch offthe unit and unplug the mains.

Duringinspectionthefollowing pointsshould bechecked:

 All screws used forinstalling the device and any of its parts shouldbe tightly fastened and may not be corroded.

 Housings, fixations andinstallations spots (ceiling, truss, suspensions)should be totallyfree from any deformation.

 The mains cables must be in impeccable condition andshould be replaced immediately when even a small problemis

detected.

SPECIFICATIONS

Supplyvoltage: 3x24V common anode

Powerconsumption: 2 Watt/meter

Cuttingmarks: every 50 cm

Soundcontrol: none, see LedManager

Diameterropelight: 14 mm

Size: 30 m

Weight: 192 g/meter

Every information is subjectto change without prior notice

You can download the latestversion ofthisuser manualon our website: www.beglec.com

FRANÇAIS MODE D’EMPLOI

JB SYSTEMS

®

6/25 LED ROPE LIGHT

Merci d’avoir choisi ce produitJB Systems

®

. Pourvotre sécurité et pour une utilisationoptimale de toutes les possibilités

de l’appareil,lisez attentivement cettenotice avant utilisation.

EN VOUS INSCRIVANT POUR LA LETTRE D’INFORMATION VOUS SEREZ TOUJOURS TENU AU

COURANT DES DERNIERES NOUVELLES CONCERNANT NOS PRODUITS: NOUVEAUTES,

ACTIONS SPECIALES, JOURNEES PORTES OUVERTES, ETC.

 SURFEZ SUR: WWW.BEGLEC.COM 

CARACTERISTIQUES

Il répond aux exigences nationales et européennes. La conformité a été établie et les déclarations et documents

correspondants ont été déposés parle fabricant.

 Cet appareil a été conçu pour laproduction de jeuxde lumières décoratifset estutilisé dansdes spectacles lumineux.

 Guirlande lumineuse flexiblemulticolore RVB(rond, D = 14mm) avec àl’intérieur des LED super brillantes.

 Parfait pour des façades multicolores (utilisation à l'intérieur comme à l'extérieur), la décoration de bars, discothèques,

magasins, etc …

 Peut être plié pour épouser la forme des murs et/oudes coins.

 Connecteurs à4brochessolides avec verrouillage.

 A utiliser avec le LEDMANAGER (alimentation LEDpar DMX)

 En longueurde 30mètres qui peuvent être coupés tousles 50cm.

 Consommation: 2Watt/mètre

 Câbles d’alimentation, connecteurs de liaison, capuchons pour fermer les extrémités et clips de montage disponibles

séparément.

Remarqueimportante : cetteguirlandelumineuse fonctionne exclusivement en association avec un appareil séparé, le

LED MANAGER (alimentation LED par DMX), auquel elle doit être raccordée. Il est donc impossible de la faire

fonctionnerseule."

AVANT UTILISATION

 Avant d’utiliser cet appareil, assurez-vous de l’absence de dommages liés au transport. En cas de dommages,

n’utilisez pasl’appareil etcontactez le vendeur.

 Important: Cet appareil a quitté notre usine en parfaite condition et bien emballé. Il est primordial que l’utilisateur

suive les instructions de sécurité et avertissements inclus dans ce manuel. La garantie ne s’applique pas en cas de

dommage lié à une utilisation incorrecte. Le vendeur ne prend pas la responsabilité des défauts ou de tout problème

résultantdu fait de n’avoir pas tenu compte des mises en garde de ce manuel.

 Conservez ce manuel dans un endroit sûr pour toute consultation future. Si vous vendez l’appareil, assurez-vous d’y

joindre cemanuel également.

 Afin de protéger l’environnement, merci de recycler les emballages autant que possible.

Vérifiezlecontenu:

Vérifiez si l’emballage contient bien les articles suivants:

 Led Rope Light de 30m

 Mode d'emploi

INSTALLATION DE LA GUIRLANDE LUMINEUSE

ET DE SES ACCESSOIRES

QUELQUES REMARQUES IMPORTANTES

!!Cette guirlande lumineuseà LED nepeut être utilisée qu'avec le JB SYSTEMS

®

LEDMANAGER

exclusivement !!

!!!Donc, NE LACONNECTEZ PAS DIRECTEMENT AU230 VOLTS !!!

N'utilisez pas deslongueurs deplus de 30mètres,les conducteurs internes seraient en surcharge, ce qui

endommageraitlaguirlandelumineuse.

(Pour plus d'info, sereporterci-dessous)

Page is loading ...

JB Systems Light LED ROPE, B04967, Led Rope Light, LED ROPE LIGHT RGB Owner's manual

Related papers

Other documents