BEGLEC Led Rope Light Owner's manual

Type
Owner's manual

This manual is also suitable for

Version: 1.1
WWW.BEGLEC.COM
Copyright © 2007 by BEGLEC cva.
Reproduction or publication of the content in any manner, without express permission of the publisher, is prohibited.
LED Rope
Light
Operation Manual
Mode d'emploi
Gebruiksaanwijzing
Bedienungsanleitung
Manual de instrucciones
EN
FR
NL
DU
ES
EN - DISPOSAL OF THE DEVICE
Dispose of the unit and used batteries in an environment friendly manner
according to your country regulations.
FR - DÉCLASSER L’APPAREIL
Débarrassez-vous de l’appareil et des piles usagées de manière écologique
Conformément aux dispositions légales de votre pays.
NL - VERWIJDEREN VAN HET APPARAAT
Verwijder het toestel en de gebruikte batterijen op een milieuvriendelijke
manier conform de in uw land geldende voorschriften.
DU - ENTSORGUNG DES GERÄTS
Entsorgen Sie das Gerät und die Batterien auf umweltfreundliche Art und
Weise gemäß den Vorschriften Ihres Landes.
ES - DESHACERSE DEL APARATO
Reciclar el aparato y pilas usadas de forma ecologica conforme a las
disposiciones legales de su pais.
PT - COMO DESFAZER-SE DA UNIDADE
Tente reciclar a unidade e as pilhas usadas respeitando o ambiente e em
conformidade com as normas vigentes no seu país.
ENGLISH OPERATION MANUAL
JB SYSTEMS
®
1/25 LED ROPE LIGHT
Thank you for buying this JB Systems
®
product. To take full advantage of all possibilities and for your own safety, please
read these operatinginstructions verycarefully before you start using thisunit.
FEATURES
This product meets the requirements of the current European and national guidelines. Conformity has been established
and the relevant statements anddocuments havebeen deposited by themanufacturer.
This device hasbeen designed toproduce decorative effect lightingand is used in light show systems.
RGB Multicolorflexible ropelight (round, D=14mm) withsuper bright LEDs inside.
Perfect forindoor and outdoormulticolor façade decorationof bars, discotheques, shops, …
Can be bended to follow the shape of walls andcorners.
Solid 4pinconnectorswith security lock.
To be used with our LED-MANAGER (dmxpower supply)
Comes in 30 mlengths that can be cutevery 50cm.
Lowpowerconsumption: 2 Watt/meter
Power cables, middle connectors, end capsand mounting clips separately available.
Importantremark : The led rope does only work in cooperation with a separate device, the LED MANAGER (to control
the rope light by DMX). It’s impossible to use the led rope light separately.
BEFORE USE
Before you start using this unit,please check if there’s no transportation damage. Shouldthere be any, do not use the
device and consult yourdealer first.
Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary for the user to
strictly follow the safety instructions and warnings in this user manual. Any damage caused by mishandling is not
subject to warranty. The dealer will not accept responsibility for any resulting defects or problems caused by
disregardingthisuser manual.
Keep this booklet in a safe place for future consultation.If yousell the fixture, be sure to addthis user manual.
Check thecontents:
Check that the carton contains the followingitems:
Operatinginstructions
30m Ledrope light
INSTALLING THE LED ROPE LIGHT AND ACCESSORIES
SOME IMPORTANT REMARKS:
With all LEDs switched on, thisrope lightconsumes about 2 Watts/meter. This means you can connect up to 150m on
1 LED MANAGER (75m on each output: 2x 75m = 150m)
The rope light canbe cut every 50cm (cutting marks available)
This product can be used inindoor and outdoor situations, the maximum ambient temperature is 45°C.
!!This LED RGBrope lightcan only be used together with theJB SYSTEMS
®
LED MANAGER !!
!!!DON’T CONNECT DIRECTLY TO230 Vac!!!
Don’t use lengths over 30m, theinternal conductors willbe overloaded which will damage therope light!! (
more infobelow )
ENGLISH OPERATION MANUAL
JB SYSTEMS
®
2/25 LED ROPE LIGHT
SOME ACCESSORIES EXPLAINED:
POWER CABLE: this power cable is used to connect the rope light to the LED MANAGER. This can be done by
simplyconnecting the conductorsof the powercable with the coloredconductors ofthe cables delivered with the LED
MANAGER.
MIDDLECONNECTOR:
Used to link 2pieces of LED RGB rope light together.
ENDCAP: Used to seal the end of a rope light.
MOUNTING TRACKS (2m): Used to guide the rope light when it is installed on a flat surface. You will be come a
nicely aligned straightrope light.
ENGLISH OPERATION MANUAL
JB SYSTEMS
®
3/25 LED ROPE LIGHT
INSTALLING THE LED ROPE LIGHT:
You can installthe rope light easily on any surface, we suggest using the optional mounting tracks. Do NOT use lengths
over 30m, this may damage the internal conductors! When you have to install lengths over 30m, just split up the
installation in several individual lengths. With a sharp cutting device (very sharphobby knife or wire cutter) you can easily
cut the rope light on the cutting marks ( scissor symbol every 50cm) to split it up in several parts. See “how to make a
length of over 30m” for more info!
1.
2. CUT THE CABLE ATA SCISSORSYMBOL
3. WHEN YOU CONNECT WITH THE POWER CABLE, ALWAYS MAKE SURE THAT THE 24V
SIGN ON THE CABLEIS ON YOUR RIGHT
HOW TO MAKE A LENGTH OF OVER 30M ?
This is an example for 2 pieces with a combined length of 50m.
1. 24 VPower LED rope
2. LED Manager cable assembly
3. 4 conductorcable
4. 24 VPowercable
INSTALLING THE MOUNTING TRACKS:
Use a small hacksaw to cut the mounting tracks to the desired lengths. You can fix them to the surface using strong glue
or small screws. When all tracks are in place youjust have to press the ropelight in the mounting tracks. Done!
LINKING 2 LED ROPE LIGHTS:
Remove the sealing rings on both sides of the middle connector and push the sealing rings over the 2 rope light ends.
Press the 4sharppins of themiddle connectorin the 4conductor holes of 1rope light.
Attention: the holes and pins are a little out of the center, make sure to insert the pins in the right way and push the
middle connector as far aspossible on the rope light! Put the sealingring back in place and tighten it well. Do exactly the
same thing withthe other ropelight end. Ready!
ENGLISH OPERATION MANUAL
JB SYSTEMS
®
4/25 LED ROPE LIGHT
INSTALLING THE POWER CABLE:
The power cable comes together with a rope light connector that must be installed on the rope light first. Refer to the
pictures 1 and 2below.
Attention: the holes and pins are a little out of the center, make sure to insert the pins in the right way and push the
connector from the power cable as far as possible on the rope light! Put the sealing ring back in place and tighten it well.
Ready!
1. 2.
Strip the other end of the power cable and connect it to one of the two small cable assemblies that came with the led
manager. Referto picture 3 for the corresponding colours ofthe wires!
3.
INSTALLING THE END CAP:
The end of the rope light must be sealed. To make it waterproof you must put some silicon on the inside of the cap
before you press it onthe ropelight.
ENGLISH OPERATION MANUAL
JB SYSTEMS
®
5/25 LED ROPE LIGHT
CONNECTING 2 ROPE LIGHTS TROUGH A CABLE:
When you want to connect 2 led ropes trough a piece of cable, you put 2 power cables to each other. You do this as
shown below ( watch the color code + ropemarkings ! ) :
Blue Blauw/Bleu/Blau/Azul
Brown Bruin/Brun/Braun/Marrón/Marrom
Yellow-green Geel-groen/Jaune-vert/Gelb-grün/Amarillo-verde/Amarelo-verde
Black Zwart/Noir/Schwarz/Negro/Preto
OPERATING INSTRUCTIONS
Onceconnected tothe LEDMANAGER the devicestarts running.
Inthe event of serious operating problems, stop using thefixture and contact yourdealer immediately.
Important: Never look directly into the light source! Don’t use the effect in the presence of persons suffering from
epilepsy.
MAINTENANCE
Make sure the area below the installationplaceis free from unwanted persons during servicing.
Switch offthe unit and unplug the mains.
Duringinspectionthefollowing pointsshould bechecked:
All screws used forinstalling the device and any of its parts shouldbe tightly fastened and may not be corroded.
Housings, fixations andinstallations spots (ceiling, truss, suspensions)should be totallyfree from any deformation.
The mains cables must be in impeccable condition andshould be replaced immediately when even a small problemis
detected.
SPECIFICATIONS
Supplyvoltage: 3x24V common anode
Powerconsumption: 2 Watt/meter
Cuttingmarks: every 50 cm
Soundcontrol: none, see LedManager
Diameterropelight: 14 mm
Size: 30 m
Weight: 192 g/meter
Every information is subjectto change without prior notice
You can download the latestversion ofthisuser manualon our website: www.beglec.com
FRANÇAIS MODE D’EMPLOI
JB SYSTEMS
®
6/25 LED ROPE LIGHT
Merci d’avoir choisi ce produitJB Systems
®
. Pourvotre sécurité et pour une utilisationoptimale de toutes les possibilités
de l’appareil,lisez attentivement cettenotice avant utilisation.
EN VOUS INSCRIVANT POUR LA LETTRE D’INFORMATION VOUS SEREZ TOUJOURS TENU AU
COURANT DES DERNIERES NOUVELLES CONCERNANT NOS PRODUITS: NOUVEAUTES,
ACTIONS SPECIALES, JOURNEES PORTES OUVERTES, ETC.
SURFEZ SUR: WWW.BEGLEC.COM
CARACTERISTIQUES
Il répond aux exigences nationales et européennes. La conformité a été établie et les déclarations et documents
correspondants ont été déposés parle fabricant.
Cet appareil a été conçu pour laproduction de jeuxde lumières décoratifset estutilisé dansdes spectacles lumineux.
Guirlande lumineuse flexiblemulticolore RVB(rond, D = 14mm) avec àl’intérieur des LED super brillantes.
Parfait pour des façades multicolores (utilisation à l'intérieur comme à l'extérieur), la décoration de bars, discothèques,
magasins, etc
Peut être plié pour épouser la forme des murs et/oudes coins.
Connecteurs à4brochessolides avec verrouillage.
A utiliser avec le LEDMANAGER (alimentation LEDpar DMX)
En longueurde 30mètres qui peuvent être coupés tousles 50cm.
Consommation: 2Watt/mètre
Câbles d’alimentation, connecteurs de liaison, capuchons pour fermer les extrémités et clips de montage disponibles
séparément.
Remarqueimportante : cetteguirlandelumineuse fonctionne exclusivement en association avec un appareil séparé, le
LED MANAGER (alimentation LED par DMX), auquel elle doit être raccordée. Il est donc impossible de la faire
fonctionnerseule."
AVANT UTILISATION
Avant d’utiliser cet appareil, assurez-vous de l’absence de dommages liés au transport. En cas de dommages,
n’utilisez pasl’appareil etcontactez le vendeur.
Important: Cet appareil a quit notre usine en parfaite condition et bien emballé. Il est primordial que l’utilisateur
suive les instructions de sécurité et avertissements inclus dans ce manuel. La garantie ne s’applique pas en cas de
dommage lié à une utilisation incorrecte. Le vendeur ne prend pas la responsabilité des défauts ou de tout problème
résultantdu fait de n’avoir pas tenu compte des mises en garde de ce manuel.
Conservez ce manuel dans un endroit sûr pour toute consultation future. Si vous vendez l’appareil, assurez-vous d’y
joindre cemanuel également.
Afin de protéger l’environnement, merci de recycler les emballages autant que possible.
Vérifiezlecontenu:
Vérifiez si l’emballage contient bien les articles suivants:
Led Rope Light de 30m
Mode d'emploi
INSTALLATION DE LA GUIRLANDE LUMINEUSE
ET DE SES ACCESSOIRES
QUELQUES REMARQUES IMPORTANTES
!!Cette guirlande lumineuseà LED nepeut être utilisée qu'avec le JB SYSTEMS
®
LEDMANAGER
exclusivement !!
!!!Donc, NE LACONNECTEZ PAS DIRECTEMENT AU230 VOLTS !!!
N'utilisez pas deslongueurs deplus de 30mètres,les conducteurs internes seraient en surcharge, ce qui
endommageraitlaguirlandelumineuse.
(Pour plus d'info, sereporterci-dessous)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15

BEGLEC Led Rope Light Owner's manual

Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI