Toto Clean Dry HDR110#SS Installation guide

Brand: Toto

Model: Clean Dry HDR110#SS

Type: Installation guide

Toto Clean Dry HDR110#SS is a high-speed concealed hand dryer with a power rating of 120V AC, 4.25 Amps, 60 Hz, and 510 W. It features a power-saving function that automatically turns off after 60 seconds of use, reducing energy consumption. With a decibel rating of 58 dB, it operates quietly, making it suitable for use in various environments. The dryer boasts an impressive air speed of 224 mph (100 meters/second), ensuring fast and efficient hand drying in just 12 seconds. It has a drain tray capacity of 0.

INSTALLATION MANUAL Clean Dry™

High Speed Concealed Hand Dryer

Important Safeguards

(For your safety, please follow the instructions below.)

Warning

Ignoring these symbols may cause

personal injury and/or property damage.

*Some models may have different components from the ones illustrated below.

Do not install the unit in the places where corrosive

or combustible gas can be present.

This may cause product failure or damage.

Do not use in

humid area

Warning

Never attempt to disassemble for repair or

modification.

This may cause electric shock, fire, injury or failure

Do not install outdoors or where it is exposed to

water.

This may cause current leakage, electric shock, fire, or failure.

Do not

disassemble

Specification

0GU3049E 2009.04

Do not

Caution

Ignoring these symbols may cause

severe injury and/or property damage.

Product HDR110#SS

Power Rating 120V AC, 4.25 Amps, 60 Hz, 510 W

Power Saving Function Automatically turns OFF after 60 seconds of use

58 dB

Ambient temperature 32° - 104°F (0° - 40°C)

Size

9-5/8" x 18-1/2" x 6-5/16"

Decibel Rating

Power Connection Hardwiring

224 mph (100 meters/second)

Air Speed

12 seconds

Dry Time

0.27 gal (950 ml)

Drain Tray Capacity

Weight

22.2 lbs (10kg)

Warning

It is necessary to install a circuit-breaker in the power supply

Failure to do this may cause electric shock during overload or short

circuit.

Important

Caution

The chassis assembly must be installed on a smooth and even

wall surface which has enough strength.

Failure to do this may cause damage or personal injury if it falls down.

Important

In this Instruction Manual, the following symbols are shown for safe and proper use of

the product and to alert you of the possibility of personal injury and damage to your

property.

The symbols and their meanings are as follows:

Warranty Registration and Inquiry

For product warranty registration, TOTO U.S.A. Inc. recommends online Warranty Registration. Please visit our web site http://www.totousa.com. If you have questions regarding warranty policy or

coverage, please contact TOTO U.S.A. Inc., Customer Service Department, 1155 Southern Road, Morrow, GA 30260 (888) 295 8134 or (678)466-1300 when calling from outside of U.S.A.

HandDryerSupply.com | 804-859-2498 | [email protected]

Before Installing

Precautions

2. Others

Confirm the rough-in, major dimensions and wiring diagram before installation

in order to properly install the hand dryer and electrical wiring.

All electrical wiring should be installed in accordance with national/local codes

and regulations with assistance from a certified electrician.

Mounting surface should be even and smooth.

Confirmation must be made that the wall has enough strength for hand dryer

installation and be sure to use all the mounting hardware provided to securely

install the hand dryer.

It is necessary to install circuit breaker for the power supply.

Pay special attention so that both the top cover and the sensor surface are

not flawed or scratched.

Do not place other devices using inverter or infrared sensor near the

hand dryer, this may cause malfunction.

Set-up Drawing

Some models may have different components as illustrated below.

Recommended mounting bracket heights from floor are as follow:

- Male/Female: 29-1/2” (750 mm)

- Children: 23-1/2” (598 mm)

- Handicapped: 21-1/2” (547 mm)

Meets the American Disabilities Act Guidelines, ANSI A117.1 and CSA B651 requirements

when mounted in a recessed wall where the front surface is not more than 4” (102mm) from

finished wall and max. height of air blower outlet from finished floor is 47-1/4” (1200mm).

FLOOR

1-9/16″ (40mm)

3-9/16″ (90mm)

2-3/8″ (60mm)

FINISHED

WALL

OPEN WALL

1-9/16″

(40mm)

3-1/8″ (80mm)

2-3/4″ (70mm)

1-3/16″ (30mm)

26-5/16″

(668mm)

11-13/16″

(300mm)

5-1/8″

(130mm)

1-5/16″

(34mm)

2″ (50mm)

Junction box

location

27-9/16″ - 27-5/8″ (700±2 mm)

1-9/16″

(40mm)

12-5/8″

(320mm)

28-3/4″

(730mm)

5-1/8″

(130mm)

6-7/16″

(164mm)

26-5/16″ (668mm)

9-15/16″ (252mm)

2″

(50mm)

HandDryerSupply.com | 804-859-2498 | [email protected]

Installation

*Some models may have different component as illustrated below.

※

Hand Dryer Unit

w/o Top Cover

Accessories

Model is subject to change without further notification.

Mounting Bracket Screws and Vandal Resist Hex Wrench Template

Installation Manual

(φ4.5×30) ×6

(M4×6) ×2

Bracket (Top)

Bracket (Bottom)

Installation

position

Installation

position

Wiring Hole

Water Tray

Chassis Assy

Filter

Filter case

Top cover

Drain tray

Power Cable

Filter case

Wall surface

Sensor

Air nozzles

Junction box

(Connection type)

Color : White,Black,Green

Size : AWG16×3

HandDryerSupply.com | 804-859-2498 | [email protected]

Installation Procedure

To be continued on the back

・

Attach the bracket firmly on the rigid wall with the three screws (φ4.5×30)

provided.

In the case of a tile or concrete wall, please use plastic plug anchors with

screws provided.

Mark the wall with template and install the bracket

Caution

Chassis Assy. must be installed on a rigid and even surface

Failure to do this may cause damage or personal injury when it falls.

STEP 1

Recommended mounting bracket heights from floor are as follow:

- Male/Female: 29-1/2” (750 mm)

- Children: 23-1/2” (598 mm)

- Handicapped: 21-1/2” (547 mm)

1-9/16″

(

40mm)

Finished

wall

Finished

wall

1-9/16″

(40mm)

3-1/8

″

(80mm)

2-3/4

″

(70mm)

2-3/4

″

(70mm)

Bracket (Bottom)

Beam/Stud

1-9/16″ (40mm)

Wall

Finished Wall

Remove drain tray

during installation

△

Junction box

location

Drain tray

Wall thickness needs

to be 5 to 30mm.

Wall thickness needs

to be 5 to 30mm.

Bracket

(Top)

Beam/Stud

Using template provided, mark the wall for locations and install

the mounting bracket.

Complete the electrical wiring; install the junction

box, and connect the power cord using wire nuts.

Mount the chassis assembly and drain tray assembly

Install the top cover and drain tray

1-9/16″ (40mm)

1-9/16

″

(40mm)

3-1/8

″ (80mm)

2-3/4

″ (70mm)

2-3/4

″ (70mm)

1-3/16

″ (30mm)

1-3/16

″ (30mm)

″ (50mm)

3-9/16″ (90mm)

2-3/8″ (60mm)

3-9/16″ (90mm)

2-3/8″ (60mm)

HandDryerSupply.com | 804-859-2498 | [email protected]

STEP 2 －

STEP 3

STEP 2

Complete the electrical wiring

STEP 3

Mount the Chassis Assembly and Drain Tray

Assembly

※

Connection

Diagram

Connect the cord firmly with a wire nut or equivalent.

・

Make sure all electrical wiring is placed away inside the junction box.

Use 2 screws (M4) that come with the product and tighten unit to the bottom

bracket.

・Place chassis assembly onto the bottom bracket.

・Using wire nuts, connect power cable from hand dryer to power supply in the

junction box (confirm with certified electrician on correct wire nuts to use).

・Place connection point (with wire nuts) into the junction box.

・Hang chassis assembly onto the top bracket.

Connection point

(Actual Placement)

Junction box

Place mounting platform

onto mounting bracket hooks.

Place connection point (with

wire nuts) into the junction box

(Actual Placement)

Junction box

Chassis

Assy

Bracket (Top)

Bracket (Bottom)

Attach water tray after

installation is complete

Screw in two screws onto bottom

of body through the bottom bracket

(Actual Placement)

Junction box

Chassis Assembly

Drain tray

HandDryerSupply.com | 804-859-2498 | [email protected]

■

・

After trial run

Test the product as follows after the installation is complete.

Check the circuit breaker

Check the functionality

Turn the circuit breaker ON.

Place your hand under the outlet nozzles to see if air blows out.

After you check the functionality by trial run, give the user manual

(with warranty) to the customer, and explain how to use and maintain the

product.

First peel off the seal on the filter.

(The seal is used to protect the filter from scratches during

shipment; it is no longer needed.)

B=BLACK

R=RED

W=WHITE

Bu=BLUE

G=GREEN

Sensor

Control

Assembly

Motor

Power

Connector

Power Fuse

Motor

P1-1

P1-2

15A

Body Case

Function Test

1. Checking after installation

Wiring Diagram

Peel off the seal

Air nozzles

HandDryerSupply.com | 804-859-2498 | [email protected]

Toto Clean Dry HDR110#SS Installation guide

Toto Clean Dry HDR110#SS Installation guide

Toto Clean Dry HDR110#SS Installation guide

Related papers

Other documents