Wolf DD30R Planning Information

Brand: Wolf

Model: DD30R

Category: Deep fryers

Type: Planning Information

This manual is also suitable for

DD30I

Wolf DD30R is a downdraft ventilation system that can be used with Wolf induction, framed electric and gas cooktops and integrated modules. It features a remote-mounted control module, three-speed blower control, and a filter clean timer. The DD30R is also equipped with a stainless steel filter cover and dishwasher-safe aluminum mesh filter. With an accessory trim kit, the DD30R can be used with sealed burner rangetop Model SRT304.

Dimensions in parentheses are in

millimeters unless otherwise specified.

9/07

Planning Information

30" (762) Downdraft Ventilation System

MODELS DD30I AND DD30R

The cooktop downdraft rises from the countertop to

whisk away odors and smoke into the easy-to-clean,

five-layer mesh filter. For ease in matching your Wolf

cooktop, the remote-mounted control module and top

cover are available in the exclusive premium finishes

of platinum or carbon stainless steel, or the standard

classic stainless steel finish.

Wolf downdraft ventilation systems are recommended

for use with Wolf induction, framed electric and gas

cooktops and integrated modules. They cannot be

used with unframed electric cooktops and are not

recommended for use with the electric grill, steamer

and fryer modules.

A Pro ventilation hood is recommended for use with

Wolf dual fuel ranges, gas ranges, sealed burner

rangetops and gas rangetops. With an accessory trim

kit, the 30" (762) downdraft can be used with sealed

burner rangetop Model SRT304.

Control module and top cover for

the 30" (762) downdraft come in classic,

platinum and carbon stainless steel

finishes and are available as sales acces-

sories. Model DD30I includes a 500 CFM

internal blower. In-line and remote blower

options are available for Model DD30R.

Model DD30I

Internal Blower Included

Model DD30R

In-Line or Remote Blower

Required

Stainless steel

filter covers

Top cover available

in three finishes

Remote-mounted

control module

Location of

rating plate

Three-speed

blower control

9" (229) chimney

elevation

Aluminum mesh

filters

Dimensions in parentheses are in

millimeters unless otherwise specified.

Unit dimensions may vary by ±

" (3).

Planning Information

30" (762) Downdraft Ventilation System

MODELS DD30I AND DD30R

FEATURES

Classic, platinum and carbon stainless steel

finishes available on control module and top

cover

Remote-mounted control module

Internal, in-line and remote blower options

Three-speed blower control

Filter clean timer lets you know when the

filter needs cleaning

Delay-off feature automatically turns unit off

after five minutes, chimney remains up

Stainless steel filter cover with dishwasher-

safe aluminum mesh filter

LED indicators

Downdraft control kit, available as a sales

accessory—includes control module, top

cover, mounting brackets, RJ45 connector

and mounting hardware

UL listed to US and Canadian safety

standards

Two and five year residential warranty—

exclusions apply; warranty information can

be found on our website, wolfappliance.com

/8"

(60)

30"

(762)

/16"

(230)

/4"

(667)

/2" (38)

DEPTH OF

DOWNDRAFT CHIMNEY

OVERALL DIMENSIONS

Dimensions in parentheses are in

millimeters unless otherwise specified.

Planning Information

30" (762) Downdraft Ventilation System

MODELS DD30I AND DD30R

SPECIFICATIONS

Overall Width 30" (762)

Overall Height (above countertop) 9

/16" (230)

Overall Depth 2

/8" (60)

Duct Size (Model DD30I) 3

/4" (83) x 10" (254)

Duct Size (Model DD30R) 3

/4" (83) x 14" (356)

Discharge Adjustable

Recommended Cabinet Width 33" (838)

Minimum Cabinet Width 30" (762)

Minimum Flat Countertop Depth* 25

/8" (638)

Downdraft Cut-Out Width 27" (686)

Downdraft Cut-Out Depth 2

/4" (70)

Electrical Supply Requirements 110 /120 V AC

60 Hz, 15 amp circuit

Power Cord 2

/2' (.8 m) power cord

with grounded plug

Shipping Weight 75 lbs (34 kg)

*Depth of countertop increases for installation with the sealed

burner rangetop. Refer to installation instructions provided with

the SRT/downdraft trim kit.

Specifications are subject to change without notice.

MODEL OPTIONS

Downdraft with 500 CFM

Internal Blower Included DD30I

Downdraft Only—In-Line or

Remote Blower Required DD30R

For Model DD30R, see in-line and remote

blower options below.

BLOWER OPTIONS

1100 CFM In-Line Blower 808332

900 CFM Remote Blower 801641

1200 CFM Remote Blower 801642

1500 CFM Remote Blower 804701

Refer to Cooktop Ventilation Recommen-

dations at the end of this section.

TRIM OPTIONS

Classic Stainless DD30CONTROL/S

Platinum Stainless DD30CONTROL/P

Carbon Stainless DD30CONTROL/B

Control module and top cover are

available in three finishes. Control kits

also include mounting brackets, RJ45

connector and mounting hardware and

are available as sales accessories.

ACCESSORIES

Bracket supports for installation

of two integrated modules with

downdraft

SRT/Downdraft trim kit for use

with sealed burner rangetop

Model SRT304

Transitions in various sizes

Accessories are available through your

Wolf dealer. To obtain local dealer

information, visit the Showroom Locator

section of our website, wolfappliance.com.

COUNTERTOP CUT-OUT

27" (686)

" MIN

(64)

" (70)

COOKTOP CUT-OUT

WIDTH

" MIN

(638)

FLAT

COUNTERTOP

SPACE

(489)

IMPORTANT NOTE: Countertop cut-out dimensions will change for

installation with the sealed burner rangetop. Refer to installation

instructions provided with the SRT/downdraft trim kit.

Dimensions in parentheses are in

millimeters unless otherwise specified.

Planning Information

30" (762) Downdraft Ventilation System

MODELS DD30I AND DD30R

" (54)

" (489)

COOKTOP CUT-OUT

DEPTH

36"

(914)

" (60)

" MIN (638)

OF FLAT COUNTERTOP*

.344"

/16

(745)

COUNTERTOP

TO BOTTOM OF

AIR BOX

18"

(457)

(92)

(83)

(127)

/16

(197)

(16)

" MIN

(64)

WITH NO

RAISED LIP*

*AREAS OF POTENTIAL INTERFERENCE

24" MIN (610)

CABINET DEPTH

" MIN (45)

BACK EDGE

OF COOKTOP

TO INSIDE OF

CABINET BACK*

(181)

30"min (762)

ELECTRICAL LOCATION

IN CABINET BACK

/2" (89)

4"min (102)

10" (254)

24" min (610)

CABINET DEPTH

OPTIONAL

ELECTRICAL

LOCATION IN

ADJACENT RIGHT

SIDE CABINET

LOCATION OF ELECTRICAL

INSTALLATION SPECIFICATIONS

Dimensions in parentheses are in

millimeters unless otherwise specified.

Planning Information

30" (762) Downdraft Ventilation System

MODELS DD30I AND DD30R

INSTALLATION NOTES

Refer to the illustrations and specifications

for overall dimensions and installation specifics.

Wolf downdraft ventilation systems are

recommended for use with Wolf induction,

framed electric and gas cooktops and inte-

grated modules. The downdraft should be at

least as wide as the cooking surface.

IMPORTANT NOTE: Wolf downdraft ventilation

systems cannot be used with unframed electric

cooktops and are not recommended for use

with the electric grill, steamer and fryer

modules.

A Pro ventilation hood is recommended for

use with Wolf dual fuel ranges, gas ranges,

sealed burner rangetops and gas rangetops.

The 30" (762) downdraft can be used with

sealed burner rangetop Model SRT304. An

accessory trim kit is necessary for this installa-

tion. Contact your Wolf dealer for details.

Model DD30I has a 500 CFM internal blower.

Model DD300R is shipped without the blower

assembly. In-line and remote blower assemblies

are available. Blower options vary with the

volume of air that needs to be moved and the

length of the duct run. Refer to the cooktop

ventilation charts at the end of this section for

minimum CFM recommendations and blower

options.

IMPORTANT NOTE: Install this downdraft only

with a Wolf blower.

The 30" (762) downdraft will fit most 30"

(762) wide cabinets. It is recommended that

oversized cabinets be used for easier installa-

tion. Cabinet backs may need to be removed.

IMPORTANT NOTE: To install a downdraft

system and a Wolf cooktop, you must allow for

a minimum 25

/8" (638) flat counter space from

front to back. A countertop with a raised lip

and/or backsplash may not allow enough space

for proper installation. 2

/8" (60) of flat counter-

top is required behind the cooktop and 1

/4"

(44) is necessary between the back edge of the

cooktop and inside of cabinet back.

The remote-mounted control module is

available as a sales accessory for the 30" (762)

downdraft. Installation of the control module

must be within 10' (3 m) of the downdraft

assembly and a minimum of 4" (102) from the

outer edge of cooktop element or burner. You

will be required to drill three holes and connect

the downdraft to the control module with the

provided wire.

IMPORTANT NOTE: This appliance must be

used with a Wolf-approved control module and

top cover.

Wolf downdraft ventilation systems require a

separate, grounded 110/120 V AC, 60 Hz power

supply. The service should have its own 15

amp circuit breaker and a grounded 3-prong

receptacle should be located within the reach of

the 2

/2' (.8 m) power cord. The specific

location of the outlet is not critical, as long as it

is within reach of the power cord that is located

mid-way, top and bottom on the right side of

the downdraft.

If the 30" (762) downdraft is being installed

in a 30" (762) wide cabinet, the outlet cannot

be located on the back wall of the cabinet. It is

recommended that the outlet be placed in an

adjacent cabinet within reach of the power

cord. Refer to the illustration on page 4 for

location of electrical.

IMPORTANT NOTE: A ground fault circuit

interrupter (GFCI) is not recommended and may

cause interruption of operation.

You must follow all National Electrical Code

regulations. In addition, be aware of local codes

and ordinances when installing your service.

If the 30" (762) downdraft is installed in

combination with two integrated modules, an

integrated module support for downdraft venti-

lation is required. Accessory components are

available through your Wolf dealer.

Refer to the installation instructions shipped

with each Wolf product for detailed specifica-

tions. This information can also be found on

our website, wolfappliance.com.

Dimensions in parentheses are in

millimeters unless otherwise specified.

Planning Information

30" (762) Downdraft Ventilation System

MODELS DD30I AND DD30R

Discharge location and

adjustment for downdraft

systems.

DISCHARGE CUT-OUT

DIMENSIONS:

" (260) x 3

" (89)

INTERNAL BLOWER

" (362) x 3

" (89)

IN-LINE OR

REMOTE BLOWER

CENTERLINE OF COUNTERTOP CUT-OUT

" (416)

INTERNAL BLOWER

" (546)

IN-LINE OR

REMOTE BLOWER

" (140)

INTERNAL BLOWER

" (108)

IN-LINE OR

REMOTE BLOWER

" (562)

INTERNAL BLOWER

19" (483)

IN-LINE OR

REMOTE BLOWER

RIGHT

DISCHARGE

LOCATION

LEFT

DISCHARGE

LOCATION

CENTERLINE OF COUNTERTOP CUT-OUT

" (140)

INTERNAL BLOWER

" (108)

IN-LINE OR

REMOTE BLOWER

NOTE: Measurements are to centerline of duct cut-outs

ADJUSTMENT:

5" MAX (127)

IN-LINE OR

REMOTE BLOWER

ADJUSTMENT:

1" (25) – 7" (178)

INTERNAL BLOWER

" MAX (165)

IN-LINE OR

REMOTE BLOWER

BOTTOM

DISCHARGE

LOCATION

DUCTING CONSIDERATIONS

Downdraft (I) models include a 500 CFM internal

blower and (R) models are shipped without the

blower assembly. In-line and remote blower

assemblies are available through your Wolf

dealer.

IMPORTANT NOTE: Use only a Wolf blower

with all Wolf ventilation products.

Wolf downdraft systems have an adjustable

discharge that will allow you to negotiate

ducting around floor joists and other obstacles.

Three different discharge locations are available

with side-to-side adjustment for accurate align-

ment of ductwork. Refer to the illustration below

for discharge location and adjustment.

Dimensions in parentheses are in

millimeters unless otherwise specified.

Planning Information

30" (762) Downdraft Ventilation System

MODELS DD30I AND DD30R

Ducting options for

downdraft systems with

internal or remote

blowers.

12" MIN

GROUND

WALL CAP

INTERNAL BLOWER

INSTALLATION THROUGH WALL

REMOTE BLOWER

ROOF MOUNT INSTALLATION

12" MIN

GROUND

INTERNAL BLOWER

INSTALLATION THROUGH WALL

12" MIN

GROUND

10"

ROUND

REMOTE BLOWER

INSTALLATION THROUGH WALL

REMOTE

BLOWER

REMOTE

BLOWER

10"

ROUND

DUCTING CONSIDERATIONS

For best performance, 10" (254) round ductwork

is recommended. The downdraft will operate

most efficiently when ductwork does not exceed

40' (12 m) in length. Consult a qualified HVAC

engineer for specific ducting applications.

IMPORTANT NOTE: All Wolf downdraft systems

must be vented to the outside. Use only metal

ductwork.

Choose the ducting option that allows the

shortest length of ductwork and a minimum

number of elbows and transitions. Refer to the

illustration below for ducting options for Wolf

downdraft systems.

Refer to the cooktop ventilation charts at the end

of this section for minimum CFM recommenda-

tions and blower options.

Dimensions in parentheses are in

millimeters unless otherwise specified.

Unit dimensions may vary by ±

" (3).

Planning Information

30" (762) Downdraft Ventilation System

MODELS DD30I AND DD30R

WOLF BLOWER ASSEMBLIES

The downdraft ventilation system must include a

blower assembly. (I) models include a 500 CFM

internal blower and (R) models are shipped

without the blower assembly. An in-line or

remote blower assembly must be selected to

accommodate the cooking appliance, CFM

requirements and homeowner preferences. In-

line and remote blower assemblies are available

as sales accessories through your Wolf dealer.

IMPORTANT NOTE: Use only a Wolf blower

with all Wolf ventilation products.

In-line blowers are mounted in between the

downdraft and the exterior of the home. Remote

blowers can be mounted on the roof or in some

cases, on an exterior wall. Refer to the illustra-

tions below for dimensions of Wolf in-line and

remote blowers.

Cooktop ventilation recommendation charts on

the following page provide minimum CFM

recommendations according to the cooking

appliance and downdraft system used and

blower options for each specific downdraft.

(622)

(394)

(718)

(527)

(629)

14"

(356)

(121)

10" (254)

Diameter

(375)

(749)

18" (457)

22"

(559)

(257)

(184)

10"

(254)

10" (254)

Diameter

(375)

(749)

21" (533)

25"

(635)

(264)

(184)

10"

(254)

10" (254)

Diameter

Remote BLOWER-90REM Remote BLOWER-120REM Remote BLOWER-150REM

18"

(457)

22"

(559)

(632)

12"

(305)

18"

(457)

(203)

In-line BLOWER-110IL

Dimensions in parentheses are in

millimeters unless otherwise specified.

Planning Information

30" (762) Downdraft Ventilation System

MODELS DD30I AND DD30R

Downdraft Ventilation Systems

Blower Description Blower Number Downdraft Models

500 CFM Internal Included with (I) Models DD30I / DD36I / DD45I

1100 CFM In-Line BLOWER-110IL (808332) DD30R / DD36R / DD45R

900 CFM Remote BLOWER-90REM (801641) DD30R / DD36R / DD45R

1200 CFM Remote BLOWER-120REM (801642) DD30R / DD36R / DD45R

1500 CFM Remote BLOWER-150REM (804701) DD30R / DD36R / DD45R

Adjustable discharge. 3

" (83) x 10" (254) duct for internal blower, no transition required. 3

" (83) x 14" (356)

duct for in-line and remote blowers. TRANS-14-10 required for remote blowers.

COOKTOP VENTILATION BLOWER OPTIONS

Downdraft Ventilation Systems

Cooktop DD30 DD36 DD45

Model CT15I 215* 150*

Model CT30I 500 350

Model CT36I 500

Model CT15E 215* 150*

Model CT30E 500 350

Model CT36E 500

Model CT15G 215* 150*

Model CT30G 500 350

Model CT36G 500

Model IM15 215* 150*

Model SRT304 600

Model SRT366 900

*Use these recommendations to determine total CFM when installing multiple cooktops or modules.

Minimum CFM requirements for Wolf cooktops. CFM recommendations are based on total Btu/hr output. Additional

CFM may be required for long duct runs.

COOKTOP VENTILATION CFM RECOMMENDATIONS

Wolf DD30R Planning Information

Brand: Wolf

Model: DD30R

Category: Deep fryers

Type: Planning Information

This manual is also suitable for

DD30I

Download PDF

report

Wolf DD30R Planning Information

This manual is also suitable for

Wolf DD30R Planning Information

Related papers

Other documents