Wolf DD30I Planning Information

Wolf
Brand
Wolf
Model
DD30I
Category
Deep fryers
Type
Planning Information

This manual is also suitable for

Dimensions in parentheses are in
millimeters unless otherwise specified.
9/07
1
Planning Information
30" (762) Downdraft Ventilation System
MODELS DD30I AND DD30R
The cooktop downdraft rises from the countertop to
whisk away odors and smoke into the easy-to-clean,
five-layer mesh filter. For ease in matching your Wolf
cooktop, the remote-mounted control module and top
cover are available in the exclusive premium finishes
of platinum or carbon stainless steel, or the standard
classic stainless steel finish.
Wolf downdraft ventilation systems are recommended
for use with Wolf induction, framed electric and gas
cooktops and integrated modules. They cannot be
used with unframed electric cooktops and are not
recommended for use with the electric grill, steamer
and fryer modules.
A Pro ventilation hood is recommended for use with
Wolf dual fuel ranges, gas ranges, sealed burner
rangetops and gas rangetops. With an accessory trim
kit, the 30" (762) downdraft can be used with sealed
burner rangetop Model SRT304.
Control module and top cover for
the 30" (762) downdraft come in classic,
platinum and carbon stainless steel
finishes and are available as sales acces-
sories. Model DD30I includes a 500 CFM
internal blower. In-line and remote blower
options are available for Model DD30R.
Model DD30I
Internal Blower Included
Model DD30R
In-Line or Remote Blower
Required
Stainless steel
filter covers
Top cover available
in three finishes
Remote-mounted
control module
Location of
rating plate
Three-speed
blower control
9" (229) chimney
elevation
Aluminum mesh
filters
2
Dimensions in parentheses are in
millimeters unless otherwise specified.
Unit dimensions may vary by ±
1
/
8
" (3).
Planning Information
30" (762) Downdraft Ventilation System
MODELS DD30I AND DD30R
FEATURES
Classic, platinum and carbon stainless steel
finishes available on control module and top
cover
Remote-mounted control module
Internal, in-line and remote blower options
Three-speed blower control
Filter clean timer lets you know when the
filter needs cleaning
Delay-off feature automatically turns unit off
after five minutes, chimney remains up
Stainless steel filter cover with dishwasher-
safe aluminum mesh filter
LED indicators
Downdraft control kit, available as a sales
accessory—includes control module, top
cover, mounting brackets, RJ45 connector
and mounting hardware
UL listed to US and Canadian safety
standards
Two and five year residential warranty—
exclusions apply; warranty information can
be found on our website, wolfappliance.com
2
3
/8"
(60)
30"
(762)
9
1
/16"
(230)
26
1
/4"
(667)
1
1
/2" (38)
DEPTH OF
DOWNDRAFT CHIMNEY
OVERALL DIMENSIONS
3
Dimensions in parentheses are in
millimeters unless otherwise specified.
Planning Information
30" (762) Downdraft Ventilation System
MODELS DD30I AND DD30R
SPECIFICATIONS
Overall Width 30" (762)
Overall Height (above countertop) 9
1
/16" (230)
Overall Depth 2
3
/8" (60)
Duct Size (Model DD30I) 3
1
/4" (83) x 10" (254)
Duct Size (Model DD30R) 3
1
/4" (83) x 14" (356)
Discharge Adjustable
Recommended Cabinet Width 33" (838)
Minimum Cabinet Width 30" (762)
Minimum Flat Countertop Depth* 25
1
/8" (638)
Downdraft Cut-Out Width 27" (686)
Downdraft Cut-Out Depth 2
3
/4" (70)
Electrical Supply Requirements 110 /120 V AC
60 Hz, 15 amp circuit
Power Cord 2
1
/2' (.8 m) power cord
with grounded plug
Shipping Weight 75 lbs (34 kg)
*Depth of countertop increases for installation with the sealed
burner rangetop. Refer to installation instructions provided with
the SRT/downdraft trim kit.
Specifications are subject to change without notice.
MODEL OPTIONS
Downdraft with 500 CFM
Internal Blower Included DD30I
Downdraft Only—In-Line or
Remote Blower Required DD30R
For Model DD30R, see in-line and remote
blower options below.
BLOWER OPTIONS
1100 CFM In-Line Blower 808332
900 CFM Remote Blower 801641
1200 CFM Remote Blower 801642
1500 CFM Remote Blower 804701
Refer to Cooktop Ventilation Recommen-
dations at the end of this section.
TRIM OPTIONS
Classic Stainless DD30CONTROL/S
Platinum Stainless DD30CONTROL/P
Carbon Stainless DD30CONTROL/B
Control module and top cover are
available in three finishes. Control kits
also include mounting brackets, RJ45
connector and mounting hardware and
are available as sales accessories.
ACCESSORIES
Bracket supports for installation
of two integrated modules with
downdraft
SRT/Downdraft trim kit for use
with sealed burner rangetop
Model SRT304
Transitions in various sizes
Accessories are available through your
Wolf dealer. To obtain local dealer
information, visit the Showroom Locator
section of our website, wolfappliance.com.
COUNTERTOP CUT-OUT
27" (686)
2
1
/2
" MIN
(64)
2
3
/4
" (70)
COOKTOP CUT-OUT
WIDTH
25
1
/8
" MIN
(638)
FLAT
COUNTERTOP
SPACE
19
1
/4
"
(489)
IMPORTANT NOTE: Countertop cut-out dimensions will change for
installation with the sealed burner rangetop. Refer to installation
instructions provided with the SRT/downdraft trim kit.
4
Dimensions in parentheses are in
millimeters unless otherwise specified.
Planning Information
30" (762) Downdraft Ventilation System
MODELS DD30I AND DD30R
2
1
/8
" (54)
19
1
/4
" (489)
COOKTOP CUT-OUT
DEPTH
36"
(914)
2
3
/8
" (60)
25
1
/8
" MIN (638)
OF FLAT COUNTERTOP*
.344"
29
5
/16
"
(745)
COUNTERTOP
TO BOTTOM OF
AIR BOX
18"
(457)
3
5
/8
"
(92)
3
1
/4
"
(83)
5"
(127)
7
11
/16
"
(197)
5
/8
"
(16)
2
1
/2
" MIN
(64)
WITH NO
RAISED LIP*
*AREAS OF POTENTIAL INTERFERENCE
24" MIN (610)
CABINET DEPTH
1
3
/4
" MIN (45)
BACK EDGE
OF COOKTOP
TO INSIDE OF
CABINET BACK*
7
1
/8
"
(181)
30"min (762)
ELECTRICAL LOCATION
IN CABINET BACK
E
3
1
/2" (89)
4"min (102)
10" (254)
24" min (610)
CABINET DEPTH
OPTIONAL
ELECTRICAL
LOCATION IN
ADJACENT RIGHT
SIDE CABINET
E
LOCATION OF ELECTRICAL
INSTALLATION SPECIFICATIONS
5
Dimensions in parentheses are in
millimeters unless otherwise specified.
Planning Information
30" (762) Downdraft Ventilation System
MODELS DD30I AND DD30R
INSTALLATION NOTES
Refer to the illustrations and specifications
for overall dimensions and installation specifics.
Wolf downdraft ventilation systems are
recommended for use with Wolf induction,
framed electric and gas cooktops and inte-
grated modules. The downdraft should be at
least as wide as the cooking surface.
IMPORTANT NOTE: Wolf downdraft ventilation
systems cannot be used with unframed electric
cooktops and are not recommended for use
with the electric grill, steamer and fryer
modules.
A Pro ventilation hood is recommended for
use with Wolf dual fuel ranges, gas ranges,
sealed burner rangetops and gas rangetops.
The 30" (762) downdraft can be used with
sealed burner rangetop Model SRT304. An
accessory trim kit is necessary for this installa-
tion. Contact your Wolf dealer for details.
Model DD30I has a 500 CFM internal blower.
Model DD300R is shipped without the blower
assembly. In-line and remote blower assemblies
are available. Blower options vary with the
volume of air that needs to be moved and the
length of the duct run. Refer to the cooktop
ventilation charts at the end of this section for
minimum CFM recommendations and blower
options.
IMPORTANT NOTE: Install this downdraft only
with a Wolf blower.
The 30" (762) downdraft will fit most 30"
(762) wide cabinets. It is recommended that
oversized cabinets be used for easier installa-
tion. Cabinet backs may need to be removed.
IMPORTANT NOTE: To install a downdraft
system and a Wolf cooktop, you must allow for
a minimum 25
1
/8" (638) flat counter space from
front to back. A countertop with a raised lip
and/or backsplash may not allow enough space
for proper installation. 2
3
/8" (60) of flat counter-
top is required behind the cooktop and 1
3
/4"
(44) is necessary between the back edge of the
cooktop and inside of cabinet back.
The remote-mounted control module is
available as a sales accessory for the 30" (762)
downdraft. Installation of the control module
must be within 10' (3 m) of the downdraft
assembly and a minimum of 4" (102) from the
outer edge of cooktop element or burner. You
will be required to drill three holes and connect
the downdraft to the control module with the
provided wire.
IMPORTANT NOTE: This appliance must be
used with a Wolf-approved control module and
top cover.
Wolf downdraft ventilation systems require a
separate, grounded 110/120 V AC, 60 Hz power
supply. The service should have its own 15
amp circuit breaker and a grounded 3-prong
receptacle should be located within the reach of
the 2
1
/2' (.8 m) power cord. The specific
location of the outlet is not critical, as long as it
is within reach of the power cord that is located
mid-way, top and bottom on the right side of
the downdraft.
If the 30" (762) downdraft is being installed
in a 30" (762) wide cabinet, the outlet cannot
be located on the back wall of the cabinet. It is
recommended that the outlet be placed in an
adjacent cabinet within reach of the power
cord. Refer to the illustration on page 4 for
location of electrical.
IMPORTANT NOTE: A ground fault circuit
interrupter (GFCI) is not recommended and may
cause interruption of operation.
You must follow all National Electrical Code
regulations. In addition, be aware of local codes
and ordinances when installing your service.
If the 30" (762) downdraft is installed in
combination with two integrated modules, an
integrated module support for downdraft venti-
lation is required. Accessory components are
available through your Wolf dealer.
Refer to the installation instructions shipped
with each Wolf product for detailed specifica-
tions. This information can also be found on
our website, wolfappliance.com.
6
Dimensions in parentheses are in
millimeters unless otherwise specified.
Planning Information
30" (762) Downdraft Ventilation System
MODELS DD30I AND DD30R
Discharge location and
adjustment for downdraft
systems.
DISCHARGE CUT-OUT
DIMENSIONS:
10
1
/4
" (260) x 3
1
/2
" (89)
INTERNAL BLOWER
14
1
/4
" (362) x 3
1
/2
" (89)
IN-LINE OR
REMOTE BLOWER
CENTERLINE OF COUNTERTOP CUT-OUT
16
3
/8
" (416)
INTERNAL BLOWER
21
1
/2
" (546)
IN-LINE OR
REMOTE BLOWER
5
1
/2
" (140)
INTERNAL BLOWER
4
1
/4
" (108)
IN-LINE OR
REMOTE BLOWER
C
L
22
1
/8
" (562)
INTERNAL BLOWER
19" (483)
IN-LINE OR
REMOTE BLOWER
RIGHT
DISCHARGE
LOCATION
LEFT
DISCHARGE
LOCATION
CENTERLINE OF COUNTERTOP CUT-OUT
5
1
/2
" (140)
INTERNAL BLOWER
4
1
/4
" (108)
IN-LINE OR
REMOTE BLOWER
C
L
NOTE: Measurements are to centerline of duct cut-outs
ADJUSTMENT:
5" MAX (127)
IN-LINE OR
REMOTE BLOWER
ADJUSTMENT:
1" (25) – 7" (178)
INTERNAL BLOWER
2
1
/2
" MAX (165)
IN-LINE OR
REMOTE BLOWER
BOTTOM
DISCHARGE
LOCATION
DUCTING CONSIDERATIONS
Downdraft (I) models include a 500 CFM internal
blower and (R) models are shipped without the
blower assembly. In-line and remote blower
assemblies are available through your Wolf
dealer.
IMPORTANT NOTE: Use only a Wolf blower
with all Wolf ventilation products.
Wolf downdraft systems have an adjustable
discharge that will allow you to negotiate
ducting around floor joists and other obstacles.
Three different discharge locations are available
with side-to-side adjustment for accurate align-
ment of ductwork. Refer to the illustration below
for discharge location and adjustment.
7
Dimensions in parentheses are in
millimeters unless otherwise specified.
Planning Information
30" (762) Downdraft Ventilation System
MODELS DD30I AND DD30R
Ducting options for
downdraft systems with
internal or remote
blowers.
12" MIN
TO
GROUND
WALL CAP
INTERNAL BLOWER
INSTALLATION THROUGH WALL
REMOTE BLOWER
ROOF MOUNT INSTALLATION
12" MIN
TO
GROUND
INTERNAL BLOWER
INSTALLATION THROUGH WALL
12" MIN
TO
GROUND
10"
ROUND
REMOTE BLOWER
INSTALLATION THROUGH WALL
REMOTE
BLOWER
REMOTE
BLOWER
10"
ROUND
DUCTING CONSIDERATIONS
For best performance, 10" (254) round ductwork
is recommended. The downdraft will operate
most efficiently when ductwork does not exceed
40' (12 m) in length. Consult a qualified HVAC
engineer for specific ducting applications.
IMPORTANT NOTE: All Wolf downdraft systems
must be vented to the outside. Use only metal
ductwork.
Choose the ducting option that allows the
shortest length of ductwork and a minimum
number of elbows and transitions. Refer to the
illustration below for ducting options for Wolf
downdraft systems.
Refer to the cooktop ventilation charts at the end
of this section for minimum CFM recommenda-
tions and blower options.
8
Dimensions in parentheses are in
millimeters unless otherwise specified.
Unit dimensions may vary by ±
1
/
8
" (3).
Planning Information
30" (762) Downdraft Ventilation System
MODELS DD30I AND DD30R
WOLF BLOWER ASSEMBLIES
The downdraft ventilation system must include a
blower assembly. (I) models include a 500 CFM
internal blower and (R) models are shipped
without the blower assembly. An in-line or
remote blower assembly must be selected to
accommodate the cooking appliance, CFM
requirements and homeowner preferences. In-
line and remote blower assemblies are available
as sales accessories through your Wolf dealer.
IMPORTANT NOTE: Use only a Wolf blower
with all Wolf ventilation products.
In-line blowers are mounted in between the
downdraft and the exterior of the home. Remote
blowers can be mounted on the roof or in some
cases, on an exterior wall. Refer to the illustra-
tions below for dimensions of Wolf in-line and
remote blowers.
Cooktop ventilation recommendation charts on
the following page provide minimum CFM
recommendations according to the cooking
appliance and downdraft system used and
blower options for each specific downdraft.
24
1
/2
"
(622)
15
1
/2
"
(394)
28
1
/4
"
(718)
20
3
/4
"
(527)
24
3
/4
"
(629)
14"
(356)
4
3
/4
"
(121)
10" (254)
Diameter
14
3
/4
"
(375)
29
1
/2
"
(749)
29
1
/2
"
(749)
18" (457)
22"
(559)
10
1
/8
"
(257)
7
1
/4
"
(184)
10"
(254)
10" (254)
Diameter
14
3
/4
"
(375)
29
1
/2
"
(749)
29
1
/2
"
(749)
21" (533)
25"
(635)
10
3
/8
"
(264)
7
1
/4
"
(184)
10"
(254)
10" (254)
Diameter
Remote BLOWER-90REM Remote BLOWER-120REM Remote BLOWER-150REM
18"
(457)
22"
(559)
24
7
/8
"
(632)
12"
(305)
18"
(457)
8"
(203)
In-line BLOWER-110IL
9
Dimensions in parentheses are in
millimeters unless otherwise specified.
Planning Information
30" (762) Downdraft Ventilation System
MODELS DD30I AND DD30R
Downdraft Ventilation Systems
Blower Description Blower Number Downdraft Models
500 CFM Internal Included with (I) Models DD30I / DD36I / DD45I
1100 CFM In-Line BLOWER-110IL (808332) DD30R / DD36R / DD45R
900 CFM Remote BLOWER-90REM (801641) DD30R / DD36R / DD45R
1200 CFM Remote BLOWER-120REM (801642) DD30R / DD36R / DD45R
1500 CFM Remote BLOWER-150REM (804701) DD30R / DD36R / DD45R
Adjustable discharge. 3
1
/
4
" (83) x 10" (254) duct for internal blower, no transition required. 3
1
/
4
" (83) x 14" (356)
duct for in-line and remote blowers. TRANS-14-10 required for remote blowers.
COOKTOP VENTILATION BLOWER OPTIONS
Downdraft Ventilation Systems
Cooktop DD30 DD36 DD45
Model CT15I 215* 150*
Model CT30I 500 350
Model CT36I 500
Model CT15E 215* 150*
Model CT30E 500 350
Model CT36E 500
Model CT15G 215* 150*
Model CT30G 500 350
Model CT36G 500
Model IM15 215* 150*
Model SRT304 600
Model SRT366 900
*Use these recommendations to determine total CFM when installing multiple cooktops or modules.
Minimum CFM requirements for Wolf cooktops. CFM recommendations are based on total Btu/hr output. Additional
CFM may be required for long duct runs.
COOKTOP VENTILATION CFM RECOMMENDATIONS
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9

Wolf DD30I Planning Information

Wolf
Brand
Wolf
Model
DD30I
Category
Deep fryers
Type
Planning Information
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents