PEAK Peak lite - PL320 User manual
- Category
- Laminators
- Type
- User manual
Product instruction manual
A3 Pouch Laminating System
Peak lite - PL320
Peak laminators have been designed to be user
friendly, however we strongly recommend you take
a few minutes to read through this manual to ensure
correct operation.
Keep this manual safe for future reference.
Warranty & Incorrect Use
IMPORTANT INFORMATION
Your laminator should reach you in perfect condition, however please retain all original packaging once you have
unpacked your laminator in case you need to return it to us. If your laminator arrives damaged or faulty in anyway, this
must be reported to your supplier immediately. If you send your laminator back for repair under warranty at any time,
then the warranty may be void if the laminator is not packaged correctly and as a result is damaged in transit. The
laminator you have purchased comes with a 1 year warranty on defective parts. THIS DOES NOT COVER any jams mis-
feeds or wrap arounds caused by operator error and you will be liable for the repair costs (including delivery charges).
Safety!
.
Always remember to switch your pouch laminator o after use. Leaving it on for long periods can cause damage
to the laminator and is a health and safety hazard
.
Always put the sealed end of the pouch into the laminator rst
.
NEVER laminate metal objects such as keys or coins
.
NEVER use the laminator near water and do not leave the laminator next to a hot area such as a radiator
.
Always wrap the power cord around safely after use and do not leave it dangling where it could cause an accident
.
Do not allow children to use the laminator, unless supervised
.
If your laminator stops working, do not try to x it yourself by disassembling the machine. Contact your supplier
for advice
.
Do not operate the laminator if the power cable is damaged in any way
.
Do not use this appliance for anything other than it’s intended purpose
Please note, if you do not follow the safety guidelines above and your laminator breaks, you will not be
covered under warranty.
FAQ’S
My document has come out cloudy - what does this mean?
This means that the temperature setting is not quite hot enough. Try increasing the temperature by 5
o
and try again as applying
more heat should x the problem.
My document has come out wavy - what does this mean?
If the document comes out with a wavy nish the temperature is set too high. Decrease the temperature by 5
o
and try again. If you
have an important document to laminate such as a photograph, it is always good to try a test document rst to ensure you have the
laminator at the perfect temperature.
How to use your laminator
1) Carefully remove the laminator from all of its packaging and place it on a at, level surface. Make sure you
keep the original packaging somewhere safe (in case this is needed in the future).
2) Plug the power cable into an AC outlet and press the FORWARD button on the laminator control panel which will
turn the power on. The red power light will illuminate.
3) Set the temperature control to the required setting (see the chart opposite for guidance).
3) The laminator will begin to warm up, this will take around 5 minutes.
4) Once it has reached the set temperature, the green READY light will illuminate.
6) Once the READY power light glows green, you are ready to laminate. Place your document in the laminating pouch
ensuring that you leave a 5mm gap around the edge. If you are laminating small, cut-up or odd shaped pieces then
you will need to use a Lifejacket® (ask your supplier for more details). Feed your document and pouch into the
laminator making sure it goes in straight and SEALED END FIRST. Once laminated, the nished document will appear
at the exit of the laminator at the back.
!
Do not tug or pull the document as it comes out of the back of the laminator. Wait until it becomes free.
Once you have nished using your laminator, set the FORWARD button to the central ‘0’ position to turn it o.
It is important that you watch your document as you laminate in case of jamming. If your laminating appears to be
jamming, press the REVERSE switch and gently ease the document back out.
Temperature control
Laminating speed: 300mm/minute
Laminating width: 320mm
Maximum pouch thickness: 360 micron
Laminating temperature: 70-130
o
C
Warm up time: 5 minutes
Power supply: 240V/50Hz
Power consumption: 400W
Dimensions: 500 x 187 x 107mm
Weight: 5kgs
Warranty: 1 year
Technical Specications
Parts and Features
Diagram 1
Laminating pouch thickness Paper Type Approx temperature (
o
C)
150 to 200 micron total
(75 + 75 per side up to 100 + 100
per side)
Copy paper (80gsm) 90
Photo paper (120gsm) 85-95
Card (200gsm) 85-95
250 to 360 micron total
(125 + 125 per side up to 180 + 180
per side)
Copy paper (80gsm) 100-105
Photo paper (120gsm) 105-110
Card (200gsm) 105-110
360 micron (maximum)
(180 + 180 per side)
Copy paper (80gsm) 120
Photo paper (120gsm) 120
Card (200gsm) 120
Ready light
Temperature
control switch
Power light
RUN/REVERSE
switch
Thank you for purchasing the Peak lite PL320. Peak laminators are designed to give you professional,
high quality results, quickly and easily. Please take a few minutes to read through this important document
as any damage caused to your laminator by user error is not covered under warranty.
x
x
Don’t overlap
Leave a 5mm border Don’t laminate open
end rst
Never laminate small,
cut-up pieces without
using a Lifejacket® or you
risk jamming and damaging
your laminator (this will not
be covered under warranty)
x
What is a ‘Lifejacket®’?
The Lifejacket® is a highly durable patented product made from teon® that should be used when laminating
cut-up, odd shaped pieces (such as shapes, letters, signs as shown above) to prevent damage to your laminator
and potential jamming. Why use a Lifejacket®?
.
Protect your laminator from jamming
.
Extend the life of your laminator by using the Lifejacket® - stops adhesive seeping onto the rollers
.
Eliminate repair bills as this product keeps your laminator working at an optimum level
.
Available in A4, A3 and A2 sizes to protect documents of all sizes
Ask your supplier for more details.
Temperature control is designed for laminating pouches and documents of varying thickness. Thicker
documents need more heat. The table below gives an indication of the correct temperature setting required.
Please note this is a guide only. Other factors can aect the laminator such as room temperature and the
thickness of document being laminated.
-
1
-
2
PEAK Peak lite - PL320 User manual
- Category
- Laminators
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
PEAK Pro - PP-260 User manual
-
PEAK Pro - PP-260 User manual
-
-
-
-
-
-
-
-