Date of Purchase:
Receipt of Purchase:
Attach Here
_____ /_____ /_____
OWNER'S MANUAL
Product Code: D71 M80439
See our extensive assortment of outdoor living products on-line at www.sears.com and www.kmart.com
UPC Code: 7-6945575485-1
Clayton 12' X 10' Gazebo
with Net and Bar Table
Vendor Item: SS-I-138-2GZA
1
PARTS
Read through all the instructions before beginning assembly. Unpack and identify all the parts.
Place them on a flat, non-abrasive surface. Assembly by four people is recommended.
A1 (2)
Leg Post
(with “A1” lable)
A2 (2)
Leg Post
(with “A2” lable)
2
B (2)
Long Crossbar
with Connector
(with “B” and
“LONG” lables)
C (2)
Long Crossbar
(with “C” and
“LONG” lables)
D (2)
E (2)
Short Crossbar
(with “E” and
“SHORT” lables)
F (1)
Canopy Frame
Short Crossbar
with Connector
(with “D” and
“SHORT” lables)
G (4)
Canopy Short Bar
H (1)
I (1)
Right Side Panel
J (2)
Tabletop
Left Side Panel
K (1)
Table Surpport Bar
L (1)
Canopy Fabric
M (4)
Net
Special Warning
Assemble your gazebo on a soft, non-abrasive surface to avoid damage. The gazebo is heavy. Use care when handing.
Assembly by four adults is recommended. The gazebo is not intended to be a permanent structure. Take it down during
high winds or it may be damaged.
KEEP ALL FLAME AND HEAT SOURCES AWAY FROM CANOPY FABRIC
The canopy is made with flame-resistant fabric which meets CPAI-84 specifications. It is not fireproof. The canopy fabric
will burn if left in continuous contact with flame source. The application of any foreign substance to the canopy fabric
may render the flame-resistant properties ineffective.
Caution:
This gazebo is made for explicit purpose of providing limited outdoor sun shade and is not to be used as a toy, shelter
or tent. This gazebo is not intended for inclement weather in any form including, but not limited to: rain, hail, sleet, snow
and/or wind. Do not locate structure near any open flame. Do not use structure as a support. Do not shake, lean or climb
on structure. Children under age of 10, near the structure, should be supervised by a competent adult at all times.
ACCESSORIES
Na (32 + 2 spares)
Short Bolt
Nb (45 + 3 spares)
Medium Bolt
Nc (2)
Long Bolt
Nk (1)
Plastic Washer
Nl (8)
U Shaped Bracket
Nj (1)
Long Allen Wrench
Nd (24 + 1 spare)
Large Metal Washer
Nm (1)
Hook
Ne (59 + 3 spares)
Small Metal Washer
Nf (44 + 2 spares)
Nut
Ng (2)
Allen Wrench
Nh (2)
Open Hex Wrench
Nn (10)
Lawn Stake
No (1)
Assembly
Instructions Sheet
Np (19 + 1 spare)
Bolt Cap
Nq (12 + 1 spare)
Nut Cap
Ni (1)
Touch up Paint
3
ASSEMBLY INSTRUCTIONS
Insert the bracket of a long crossbar (B) into a
long crossbar (C). Line up the holes, and insert
a short bolt (Na) through a small metal
washer (Ne), the long crossbar (C) and secure
into the bracket of long crossbar (B) for total of
three holes. Don’t tighten completely. Repeat
procedure for remaining hole with an U shaped
bracket (Nl). Securely tighten all bolts. Repeat
procedure for the other pair long crossbar (B, C)
and 2 pairs of the short crossbars (D, E). See
Fig. 1 and Fig. 2.
For each leg post (A), place an U shaped
bracket (Nl) onto the top of the leg post (A), and
insert a short bolt (Na) through a small metal
washer (Ne), the U shaped bracket (Nl) and
secure into the leg post (A). See Fig. 3. Don’t
tighten completely.
Attach the assembled long crossbar (B&C) to
the leg posts (A). Line up all holes and for each
hole from outside insert a medium bolt (Nb)
through the L shaped bracket of the leg post (A),
the crossbar (B&C), a large metal washer (Nd)
and secure with a Nut (Nf). See Fig. 4. Repeat
procedure for the other crossbar (B&C) and two
crossbars (D&E). See Fig. 5. Tighten all bolts
and nuts. NOTE: Small thinner net bars of
crossbars (B,C,D,E) should on outside.
1
2
3
4
Nf
Nd
B
A2
A1
E
D
E
B
C
D
C
B
A1
A2
Ne
Na
Na
Ne
Nl
B
C
A1
C
B
A2
Nb
Nf
Nb
Nd
E
Na
Ne
Nl
Fig. 1
Fig. 4
Fig. 2
Fig. 5
D
E
Ne
Na
Na
Ne
Nl
Fig. 3
Attach a canopy short bar (G) to the canopy
frame (F). For each hole, from upside insert a
medium bolt (Nb) through the bracket of the
short bar (G), the canopy frame (F), a small
metal washer (Ne), and secure with a nut (Nf).
Tighten all bolts and nuts. Repeat procedure for
the remaining three canopy short bars (G).
See Fig. 6. Tighten all bolts and nuts. Cover
with nut caps (Nq).
Place the assembled canopy onto the top of the
assembled leg posts. Make sure each
crossbar (B,C,D,E) is between two edges of the
canopy (L). Line up the holes, for each hole
insert a medium bolt (Nb) through an U shaped
bracket (Nl), canopy short bar (G), a small metal
washer (Ne) and secure with a nut (Nf). Tighten
all bolts and nuts. Slide each tip end of the short
bar (G) into each pocket. See Fig. 8.
NOTE: Short side of the canopy fabric (with
“short” lable) should on the short crossbar (D&E)
4
5
6
G
F
G
G
G
L
G
L
Nf
G
F
Nb
Ne
Nq
Nf
Nl
Nb
G
Ne
s
h
o
r
t
s
h
o
r
t
Nl
Nb
Ne
Nf
F
short
5
Fig. 6
Fig. 7
Fig. 8
long
Attach the canopy fabric (L) to the canopy
frame (F&G) by inserting the bars (G) through
the holes of canopy fabric (L). Then pull down
the wind vent fabric of canopy fabric (L) and
unfold the canopy fabric (L) to the location.
See Fig. 7. NOTE: The middle of the canopy
fabric short side (with “short” lable) towards
middle-length bar of the canopy frame.
: Place the left side panel (H) and the right
side panel (I) on a non-abrasive surface and
line up the holes. For each hole from left insert
a long bolt (Nc) through a small metal
washer (Ne), side panel rims, through another
small metal washer (Ne) and secure with a
nut (Nf). See Fig. 9 and Fig. 10. Don’t tighten
completely.
: Assembled 2 table tops (J) together. Line
up the hole, from left insert a short bolt (Na)
through a small metal washer (Ne), the table
top rims, another small metal washer (Ne) and
secure with a nut (Nf). See Fig. 11. Don’t
tighten completely.
: Attach the support bar (K) to the table
tops (J). Line up the hole, from left insert a
medium bolt (Nb) through a small metal
washer (Ne), the support bar (K), a plastic
washer (Nk), table top rims, another small metal
washer (Ne) and secure with a nut (Nf). See
Fig. 12. Don’t tighten completely.
: Attach the support bar (K) to the assembled
side panels. Insert a short bolt (Na) through
a small metal washer (Ne), through the bracket
of the support bar (K) and secure into the rim of
the left side panel (H). See Fig. 13. Don’t tighten
completely.
: Unfold the left side panel (H), and line up the
holes. For each hole, from inside insert a short
bolt (Na) through a small metal washer (Ne),
table top rim and secure into the side panel (H).
See Fig. 14 and Fig. 15. Repeat procedure for
the right side panel (I). Tighten all bolts and nuts
and cover with bolt caps (Np) and nut caps (Nq).
Na
Nq
Nf
Ne
Ne
Np
K
Na
Np
Ne
H
J
J
I
H
H
I
Nc
Np
Ne
Ne
Nf
Nq
Nc
Np
Ne
Ne
Nf
Nq
Nq
Nb
Ne
K
J
J
Ne
Nf
Nk
Np
6
J
H
Na
Np
Ne
Np
Na
Ne
J
J
I
H
J
Na
Ne
Np
H
7
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13
Fig. 15
Fig. 14
CARE INSTRUCTIONS
Wash with a mild solution of soap and water; rinse thoroughly. Dry completely. Do not use bleach or solvents.
Cover furniture with outdoor furniture covers when not in use.
Made in CHINA
Distributed by Sears, Roebuck and Co., Hoffman Estates, IL 60179
See our extensive assortment of outdoor living products
on-line at www.sears.com and www.kmart.com
For questions or comments about product:
Call toll-free:
800-457-4652
Please refer to part numbers when reordering
sears.com
F
Nm
s
h
o
r
t
A1
A1
A2
A2
s
h
o
r
t
Nn
Nn
M
Ne
Nb
Np
7
Attach the assembled panel with table top to the
assembled gazebo. Line up the holes. For each
hole insert a medium bolt (Nb) through a small
metal washer (Ne), through the panel rim and
secure into the post (A1). See Fig. 16. Don’t
tighten completely. Repeat procedure for the
other side. Tighten all bolts and nuts.
Secure the gazebo to the ground by inserting
the lawn stakes (Nn) through the holes at the
bottom of the side panel or the leg post into the
ground. See Fig. 17.
Locate the nets (M) to the net bars of the top
crossbars with Velcro tabs. Attach S shaped
hook (Nm) to the ring of the canopy frame (F).
The S shaped hook is used for hanging
decoration items if necessary. See Fig. 18.
Tighten all bolts and nuts and cover with bolt
caps (Np) and nut caps (Nq).
8
9
Fig. 16
10
Fig. 17
Fig. 18
/
