TEAC DV-W50PUK Owner's manual

TEAC
Brand
TEAC
Model
DV-W50PUK
Category
Optical disc drives
Type
Owner's manual

This manual is also suitable for

page 1
The TEAC DV-W50PUK is a modern high per-
formance DVD-R/RW drive. It offers reading
speeds of 12x for DVD-ROM media and 32x for
CD-ROM media. The maximum writing speed is
rated to 4x for DVD-Rs, to 2x for DVD-RWs, 16x
for CD-Rs and 8x for CD-RWs. DVD-Rs and
DVD-RW media allow to store up to 4.7GB.
Very important:
TEAC assumes no responsibility for data
loss caused by the operation that is not
in accordance to this document, or data
loss caused by natural disaster, fire,
power outage, or spontaneous defect of
this product.
Components
Drive unit, AC adapter, USB interface cable, CD
with software, 1 CD-R, quick Installation Guide,
warranty booklet
System Requirements
PC/AT compatible machine with a USB 1.1 or
USB 2.0 interface, CPU Intel Pentium III 600MHz
or more, main memory of 128MB or more, mini-
mum 10GByte free HDD capacity, 24 bit Colour
Graphic Display with 1024 x 768 resolution
Conforming OSes
Microsoft Windows 98 Second Edition, Microsoft
Windows Me, Microsoft Windows 2000 Profes-
sional, Microsoft Windows XP Home Edition/Pro-
fessional
The drive does not conform to Windows 95, Win-
dows 98 and MS-DOS.
Setting up the drive
Windows Me, Windows 2000 and Windows XP
operating systems have the native drivers for
USB controller and TEAC DV-W50PUK. There-
fore, when this drive is connected, Windows will
automatically install the appropriate driver and
the drive will be ready to be used. You do not
have to perform any special installation or
uninstallation.
TEAC DV-W50PUK DVD-R/RW Drive
Quick Installation Guide
However, it is required that the device driver be
installed from the CD provided with this product
when you use Windows 98 Second Edition (Win-
dows 98SE). Set the provided CD in one CD-
ROM drive (not in the USB drive) of your com-
puter.
Very important:
Do not connect the drive if your PC is in
sleep or in suspend mode. Prior to con-
nect the drive you have to set your PC
in the normal mode of operation.
(1) Turn on the power of the computer and wait
for the desktop screen to appear.
(2) Connect the DC output plug of the provided
AC adapter to the DC input connector of the
drive.
0
ON
OFF
DC
IN
+5V
+12V
Audio
(3) Connect the other DC plug of the provided
AC adapter to an outlet. Set the power switch
of your USB drive to on.
(4) Connect the drive and the computer using
the provided USB cable. Insert the mini B
plug of the provided USB connector to the
USB connector at the back of the drive.
0
ON
OFF
DC
IN
+5V
+12V
Audio
page 2
Insert the A plug of the USB connector to
the USB terminal of the computer.
(5) Locate the USB terminal of your computer.
Refer to the instruction manual of your com-
puter for its location. The following logo is
usually indicated near the USB terminal.
(6) There appear some messages on the screen
followed by the appearance of an CD-ROM
icon in the window My Computer. Now the
drive is ready to use.
Very important:
When you are using Windows 98SE and
the drive is connected for the first time,
it is required to read and install the de-
vice driver file from the provided CD.
Driver installation under Windows98SE
(1) Connect as described before the dedicated
AC adapter to the drive, then connect the
USB interface cable between the drive and
your computer.
(2) Add New Hardware Wizard starts automati-
cally.
(3) Ensure your driver CD is inserted correctly
into a CD-ROM drive and select “Search for
the best driver for your device (Recom-
mended)”. Click Next.
(4) When specifying the location to search the
driver, select “CD-ROM drive” or check
“Specify a location” and input the location of
the driver folder if you have saved them in
advance on your computer (The window
below is an example if the folder DVW50PU
in drive C: is specified). Click Next.
(5) If the driver was found (TTP300.INF for USB
2.0; TTPSL11R.INF for USB 1.1), click on
Next.
(6) After sucessfully finishing the installation the
hardware assistant is closed with Finish.
Important:
If an error message appears you may
move one step backwards or cancel the
process (using Cancel) and try it again
later. If installation of the driver fails you
will see in the device manager an excla-
mation mark (!) or a question mark (?).
Remove the driver and start the installa-
tion process again.
Disconnecting the drive
The drive can be disconnected from the PC if it
is not used any longer during the actual session.
It is of major importance to logoff the drive at the
PC before disconnecting it.
(1) Close the program that uses the drive.
(2) Confirm that the busy indicator of the drive
is off.
(3) Click the Remove icon on the Taskbar.
(4) Select the removing drive with the name
assigned to the drive.
(5) The Remove Hardware confirmation mes-
sage „Save to remove storage device“ ap-
pears. Click the OK button.
(6) Remove the plug of the USB cable from the
USB terminal of the computer.
page 3
Cleaning and maintenance of your
TEAC USB DVD-R/RW drive
TEAC drives will not need maintenance if used
as specified in this manual. Usually there are only
problems with dirty or defective CDs.
Important:
If liquid is allowed to poor into the drive,
it may cause a serious malfunction, an
electric shock or a fire. When cleaning
with liquid, be sure to remove the pro-
vided AC adapter from the wall outlet
after disconnecting the drive from your
computer.
Important:
Do not use cleaning CDs which will re-
move dirt of the lense of the laser aided
by a little brush. Do not clean the inner
parts of your TEAC DVD-R/RW drive
with compressed air. Any of these meth-
ods may cause damage to your TEAC
drive.
Handling
Check the CD before inserting it into the drive. It
should not have finger prints or other dirt on it.
Especially at high reading velocities dirt may in-
crease the number of reading errors.
Very important:
Shape CDs, a kind of CD which is not
shaped like the normal round CD, are
not allowed to be used in this drive. Oth-
erwise rotational forces may cause se-
vere damage to the drive.
Installing the Writer Software
As a general precaution the installation of the
hardware has to be carried out as described be-
fore. The software installation starts with activat-
ing the reading functionality of the drive as this
is well known with any conventional CD-ROM
drive.
If the reading functionality is available the next
installation step is to achieve the writing func-
tionality provided of the writer software. More
details according the installation of your writer
software you will find in its documention [Help].
Rear panel
ON OFF
0
DC
IN
+5V
+12V
Audio
L
R
USB 2.0
Ventilator
Analogue
audio output
USB
connector
DC input
connector
Power switch
Important:
Do not disconnect the power cord or the
USB cable which connects the PC and
the drive without carrying out the logoff
procedure. Otherwise this may lead to
loss of data and erroneous operation of
the PC.
Names and Functions
Front panel
Playing back the audio CD
Use Windows Media Player or audio CD play-
back software such as Microsoft CD Player for
playing back the audio CD using the drive. The
operation method differs depending on the soft-
ware and versions. Refer to the operation manual
of your computer or software for details.
Headphone
jack
Disk trayEject emergency hole
Eject button
Volume control
ON/BUSY
indicator (LED)
Ventilation hole
page 4
Warranty is provided under the terms of the TEAC warranty conditions.
In case of warranty: www.teac.de/support
Applicable DVDs DVD-ROM and DVD-Video (single and dual layer), DVD-Audio
DVD-R (vers. 2.00), DVD-RW (vers. 1.0+1.1, DVD-RAM is not
supported
Applicable CDs CD-ROM Mode-1/650 MB/700 MB, CD-DA/74 min/79 min,
CD-ROM XA Mode-2 (Form-1)/650 MB/700 MB,
CD-ROM XA Mode-2 (Form-2)/738 MB/795 MB,
Photo-CD (Single und Multisession), CD-I, CD-Text, Video CD, CD-R,
CD-Extra (CD PLUS), CD-RW (AM2, High Speed CD-RW)
Writable DVDs* DVD-R 4.7 GB, DVD-RW 4.7 GB
Writable CDs* 12 cm CD-R /CD-RW
* Specific application programs are required for writing.
An actual list of media recommended by TEAC can be found at TEACs web site under
www.teac.de/support. Please select the menu "CD-Medias".
Disk diameter 12 cm, 8 cm
Write methods
__for DVD-R
__for DVD-RW
__for CD-R and CD-RW
Disk at once, Incremental recording, multi-border recording
Restricted overwriting
Disk at once, Track at once, Session at once, Packet write
Disk rotational speed ca. 7,200rpm max. (32 X CAV)
Rotational speed
(read mode)
12X (CAV): DVD-ROM (single layer);
8X (CAV): DVD-ROM (dual layer);
6X (CAV): DVD-R (4X media), DVD-RW (2X media);
2X (CLV): DVD-R (2X media), DVD-RW (1X media);
32X (CAV): CD-ROM, CD-R, CD-RW, CD-DA (DAE), Video CD (not
Mode-2, Form-2);
10X (CAV): CD-Audio Play; 4X (CLV): Video CD Mode-2 (Form-2)
Rotational speed
(write mode)
DVD-R: 1X/2X/4X (CLV); DVD-RW: 1X/2X (CLV);
CD-R: 4X/8X/12X/16X (CLV); CD-RW: 4X/8X (CLV)
Under some circumstances the maximum write speed may not be achieved due to external
factors (e.g. supported DVD-R/CD-R media speed or data transfer rate of the computer).
Interface USB 1.1 / USB 2.0 (High Speed)
Data rate USB 1.1: 1.5MB/sec = 12Mbit/sec; USB 2.0: 60MB/sec = 480Mbit/sec
Data buffer capacity 2MByte
Audio out Line out: 0,7Vrms±0,1Vrms (at load of 10 kOhm typ.)
ear phone (ø3.5mm stereo mini jack):
0,7Vrms±0,2Vrms (at load of 32 Ohm)
Power consumption primary: 240V/110V 50/60Hz 850mA
secondary: 5V/2.5A, 12V/1.5A
Environmental condition
Place of operation Temperature 5 to 45 °C (within 10°C/hour deviation)
Humidity 5 to 85 % (non condensing, within 10%/hour deviation)
Place of storage Temperature -20 to 60 °C (within 10°C/hour deviation)
Humidity 5 to 90 % (non condensing, within 10%/hour deviation)
Safety standards CE
Dimensions 167 (W) × 55 (H) × 273 (D) mm
Weight 1.85 kg (without AC adapter and interface cable)
Changes in specifications and features may be made without notice or obligation.
Specifications
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

TEAC DV-W50PUK Owner's manual

TEAC
Brand
TEAC
Model
DV-W50PUK
Category
Optical disc drives
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents