Hunter Fan 59230 Owner's manual

Category
Household fans
Type
Owner's manual
www.HunterFan.com
1.888.830.1326
PAGE
13
PAGE
5
30 inches
7 feet
PAGE
2
What to Expect with
Your Installation Ceiling Bracket
Ladder
PAGE
3
Tools Needed
Maintenance
& Cleaning
Troubleshooting
PAGE
8
PAGE
11
WiringDownrod
Switch Housing Light Kit
Table of Contents
Canopy
PAGE
12
Blades
PAGE
6
PAGE
7
Top Housing
PAGE
4
Mounting Options
PAGE
14
PAGE
16
?
?
?
PAGE
17
Congratulations on purchasing
your new Hunter® ceiling fan! It will
provide comfort and performance
in your home or ofce for many
years. This installation and operation
manual contains complete
instructions for installing and
operating your fan.
We are proud of our work and
appreciate the opportunity to
supply you with the best ceiling fan
available anywhere in the world.
To register your fan, please visit:
www.HunterFan.com/register
Save your receipt for proof of purchase.
1
M3606-01 • 04/21/16 • © Hunter Fan Company
www.HunterFan.com
1.888.830.1326
2
M3606-01 • 04/21/16 • © Hunter Fan Company
What to Expect with Your Installation
Know your wiring
If you are unfamiliar
with wiring, use a
qualied electrician.
You may need a
friend to help you.
Check box to see
fan weight
Assess location
30 inches
from blade tip
to nearest wall
or obstruction
7 feet
from bottom
edge of blade
to the oor
Select a downrod length
w.1 - To reduce the risk of re, electrical shock, or
personal injury, mount fan directly from building
structure and/or an outlet box marked acceptable for
fan support of 70 lbs (31.8 kg) and use the mounting
screws provided with the outlet box.
w.2 - To avoid possible electrical shock, before installing
or servicing your fan, disconnect the power by turning
off the circuit breakers to the outlet box and associated
wall switch location. If you cannot lock the circuit
breakers in the off position, securely fasten a prominent
warning device, such as a tag, to the service panel.
w.3 - To reduce the risk of re, electrical shock, or motor
damage, use only Hunter Solid State Speed Controls.
w.4 - To reduce the risk of personal injury, do not bend the
blade brackets when installing the blade brackets, balancing
the blades, or cleaning the fan. Do not insert foreign objects
in between rotating fan blades.
c.1 - All wiring must be in accordance with national and
local electrical codes ANSI/NFPA 70. If you are unfamiliar
with wiring, use a qualied electrician.
c.2 - Use only Hunter replacement parts.
Assess ceiling angle
Read and Save These Instructions
This product conforms to UL Standard 507.
WARNINGS
CAUTIONS
Must be able to
secure the fan to
building structure or
fan-rated outlet box
1
2
3
Standard Downrod
for ceilings 8-10 feet high
Shorter Downrod
for fans installed close to ceiling
Longer Downrod
for ceilings 10 feet or higher
Ceiling angles greater
than 34° will require an
Angled Mounting Kit.
See page 4 for details.
www.HunterFan.com
1.888.830.1326
Tools Needed
Ladder
Power Drill
(optional)
9/64” Drill Bit
(optional)
Screwdrivers
Pliers Wire Strippers
If mounting to a support structure, you will also need these tools.
Do not discard the hardware bags or mix
parts from different bags. Make note of
the symbol printed on each hardware
bag. The symbols can be used to identify
the appropriate hardware for each step.
3
M3606-01 • 04/21/16 • © Hunter Fan Company
www.HunterFan.com
1.888.830.1326
If you have an angled ceiling:
1. You will need a longer downrod (sold separately).
2. If your ceiling angle is greater than 34°, you will
also need an Angled Mounting Kit (sold separately).
Guide Touches
BOTH Ceiling & Wall
S
I
T
U
A
T
I
O
N
1
Guide Touches
Wall
but
NOT Ceiling
S
I
T
U
A
T
I
O
N
2
You need BOTH
a Longer
Downrod &
an Angled
Mounting Kit
You need ONLY
a Longer
Downrod
*most common
If you have a at ceiling:
Hang your fan by a standard downrod (included).
Mounting Options
Use Standard Mounting
or Low-Prole Mounting
to hang the fan from a at ceiling.
Use Angled Mounting
to hang the fan from a
vaulted or angled ceiling.
34
O
CEILING
WALL
OPTION
1
Standard
Mounting
OPTION
2
Angled
Mounting
2 3
SLIDE
toward ceiling
PLACE
against wall
1
FOLD
on dotted line
34°
Use the three steps below to determine if your ceiling angle is greater than 34°
Support
Structure
Ceiling
Outlet Box
(required)
Angled
Mounting
Style
Standard
Mounting
Style
Support
Structure
Ceiling
Outlet Box
(required)
4
M3606-01 • 04/21/16 • © Hunter Fan Company
www.HunterFan.com
1.888.830.1326
Ceiling Bracket
Refer to warning w.1 on pg. 2
To avoid possible electrical shock, before
installing your fan, disconnect the power by
turning off the circuit breakers to the outlet
box associated with the wall switch location.
For angled ceilings, point
opening toward peak.
If you are unable to do this,
call Technical Support at
1-888-830-1326.
Make sure all four bumpers are
still attached.
Use wood screws
(included) when securing
to support structure with
approved electrical outlet
box. Drill 9/64” pilot holes
in support structure to aid
in securing ceiling bracket
with hardware found in
the hardware bag.
Use machine screws
(provided with outlet
box) when securing to
existing ceiling fan-rated
outlet box. Make sure
it is securely installed
and is acceptable for fan
support of 31.8 kg (70 lbs)
or less.
OFF
Turn Power
5
M3606-01 • 04/21/16 • © Hunter Fan Company
www.HunterFan.com
1.888.830.1326
Blades
Insert each blade through the slot in the
motor housing.
Lightly attach the blades to the motor
with screws found in the hardware
bag, then securely tighten after all three
screws are attached.
6
M3606-01 • 04/21/16 • © Hunter Fan Company
www.HunterFan.com
1.888.830.1326
Top Housing
KEEP!
Remove the pre-installed
setscrew.
K
E
E
P
!
Place the top housing onto the
motor housing so that the holes
in the top housing lineup with
the holes in the motor housing
and the adapter.
Install the top housing screws
found in the hardware bag.
7
M3606-01 • 04/21/16 • © Hunter Fan Company
www.HunterFan.com
1.888.830.1326
8
M3606-01 • 04/21/16 • © Hunter Fan Company
Downrod
Slide
Slide
1 2 3 4 5
678910
Sold Separately
Sold Separately
Longer
Downrod
for angled
ceilings or
ceilings 10’ or
higher
Shorter
Downrod
for fans installed
close to ceiling
Standard
Downrod
for ceilings 8-10’ high
Option 1Option 2
Option 3
skip to next page
If you need a different downrod length follow these steps:
Steps 1-5 to remove standard downrod pipe
Steps 6-10 to reassemble with new pipe
Included
(pre-assembled)
www.HunterFan.com
1.888.830.1326
9
M3606-01 • 04/21/16 • © Hunter Fan Company
8”
3/8”
C
U
T
&
S
T
R
I
P
(not to scale)
Hand tighten the downrod (at least
4-5 full turns) until it stops.
The wires can be cut, but leave at
least 8” extending from the top of
the downrod.
Downrod (continued)
8”
3/8”
Tighten the setscrew
with pliers. DO NOT
HAND TIGHTEN.
If the setscrew is not tightened
securely, the fan may fall.
www.HunterFan.com
1.888.830.1326
Downrod (continued)
Put the wires and downrod through the
canopy. Let the canopy sit loosely on top
of the fan.
DO NOT PICK THE FAN UP BY THE
CANOPY OR WIRES. Place the downrod
ball into the slot in the ceiling bracket.
10
M3606-01 • 04/21/16 • © Hunter Fan Company
www.HunterFan.com
1.888.830.1326
Wiring
F
R
O
M
F
A
N
F
R
O
M
C
E
I
L
I
N
G
B
R
A
C
K
E
T
F
R
O
M
F
A
N
Using an orange wire
connector from
the hardware bag,
connect the 3 grounding
wires (green, green/
yellow stripe, or bare
copper) coming from the
ceiling, downrod, and
hanging bracket.
(Grounding)
Green/Yellow
Stripe
Green/Yellow
Stripe
White
Black
(Grounded)
Note: To connect the wires,
hold the bare metal leads
together and place a wire
connector over them, then twist
clockwise until tight.
Using the orange wire
connectors from
the hardware bag, connect
the black wire (ungrounded)
from the ceiling to the black
and the blue wires from the
fan. Connect the white wire
(grounded) from the ceiling to
the white wire from the fan.
Using orange wire
connectors from
the hardware bag,
connect the white wire
(grounded) from the
ceiling to the white wire
from the fan.
Connect the black wire
(ungrounded) from the
ceiling to the black wire
from the fan. Connect the
second (ungrounded) wire
from the ceiling to the blue
wire from the fan.
F
R
O
M
F
A
N
White
(Ungrounded)
Black
Blue
(Grounded)
F
R
O
M
C
E
I
L
I
N
G
(Ungrounded)
Blue
For Dual Switches
For a Single Switch
F
R
O
M
C
E
I
L
I
N
G
F
R
O
M
C
E
I
L
I
N
G
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
11
M3606-01 • 04/21/16 • © Hunter Fan Company
(Ungrounded)
www.HunterFan.com
1.888.830.1326
Canopy
Lift the canopy into place so that
the screw holes are aligned.
Position the canopy so that, when
lifted into place, the canopy ts into
the hanging bracket as shown.
Screw
Holes
Insert the two canopy screws
found in the hardware bag.
12
M3606-01 • 04/21/16 • © Hunter Fan Company
www.HunterFan.com
1.888.830.1326
Feed the wire plug through the center
hole of the upper switch housing, then
wrap keyhole slots around the screws and
twist counterclockwise.
Screw two (2) housing assembly screws
from the hardware bag halfway into
the motor housing. It does not matter
which two screw holes you choose.
Insert the third screw, found in
the hardware bag, into place and then
tighten all three (3) screws.
Make sure the upper switch housing is securely
attached to the mounting plate. Failure to properly
secure all 3 assembly screws could result in the switch
housing xture falling.
Switch Housing
13
M3606-01 • 04/21/16 • © Hunter Fan Company
www.HunterFan.com
1.888.830.1326
14
M3606-01 • 04/21/16 • © Hunter Fan Company
Light Kit
Partially install two of the switch housing
screws found in the bag.
Connect the plugs from the upper and lower
switch housings. Make sure to line up the
colored markings on the connectors. Align
the keyholes of the lower switch housing
with the upper switch housing screws. Lift the
lower switch housing. Twist the lower switch
housing clockwise to lock into place.
Light Kit
Install the third switch housing screw.
Tighten all three screws securely.
Make sure the lower switch housing is securely attached to
the upper switch housing. Failure to properly secure all three
switch housing screws could result in the light xture falling.
www.HunterFan.com
1.888.830.1326
Light Kit (continued)
See next page for fan
operation instructions.
CONGRATULATIONS!
YOU’RE DONE!
See next page for fan
operation instructions.
Connect the appropriate pull
chain pendant to each of the short
chains coming from the nial
and nial cap. The fan pull chain
controls the speed: from high to
off. The light pull chain controls
the light xture: on and off.
Light
Pull
Chain
Fan
Pull
Chain
Press the globe and globe keeper ush
against the metal plate. Thread the
light pull chain through the hole in the
center of the nial cap and thread the
fan pull chain through the hole in the
side of the cap. Finally, thread only the
light pull chain through the hole in
the nial and screw the nial onto the
threaded rod.
Install a bulb into each of the
sockets. When necessary, replace
with bulbs of the same wattage.
Finial
Finial
Cap
Globe
Keeper
Metal
Plate
Globe
15
M3606-01 • 04/21/16 • © Hunter Fan Company
www.HunterFan.com
1.888.830.1326
Maintenance & Cleaning
ON
Turn Power
Changing the direction of air
ow - move the reverse switch
to the opposite position.
Cleaning the fan - use soft
brushes or cloths to prevent
scratching. Cleaning products
may damage the nishes.
Reverse
Switch
Changing the bulbs - unscrew
the nial and remove it from the
threaded rod. Remove the nial cap
and unscrew the globe keeper while
supporting the globe with your other
hand. Carefully remove the globe.
Unscrew bulbs and replace with
bulbs of same type and wattage.
Reinstall the globe assembly.
Finial
Finial
Cap
Globe
Keeper
Metal
Plate
Globe
16
M3606-01 • 04/21/16 • © Hunter Fan Company
www.HunterFan.com
1.888.830.1326
Troubleshooting
Excessive wobbling
Tighten all of the blade and
blade iron screws until they
are snug.
Turn the power off, support
the fan carefully, and check
that the hanger ball is
properly seated.
Use the provided balancing
kit and instructions to balance
the fan.
Noisy Operation
Tighten the blade and blade
iron screws until they are snug.
Check to see if any of the
blades are cracked. If so, replace
all of the blades.
Fan doesn’t work
Make sure power switch is on.
Pull the pull chain to make sure
it is on.
Push the motor reversing switch
rmly left or right to ensure that
it is engaged.
Check the circuit breaker to
ensure the power is turned on.
Make sure the blades spin freely.
Turn off power from the circuit
breaker, then loosen the canopy
and check all the connections
according to the wiring diagram
on page 11.
Check the plug connection in
the switch housing.
17
M3606-01 • 04/21/16 • © Hunter Fan Company
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17

Hunter Fan 59230 Owner's manual

Category
Household fans
Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI