Nothern Lights M30CW3 User manual

OPERATOR’S

MANUAL

OM944W3

For Models:

M944W3 & M30CW3

Northern Lights

4420 14th Avenue N.W.

Seattle, WA 98107

Tel: (206) 789-3880

Fax: (206) 782-5455

the Northern Lights logo are trademarks of

Northern Lights, Inc.

Printed in U.S.A.

PART NO.: OM944W3 6/17

Northern Lights generator sets and /or any other

diesel powered equipment provided by NLI is not

provided with spark arresting or explosion proof

components, and therefore is not to be installed

in the presence of combustible gases having a

ash point of 43.3 Degrees C (110 Degrees F)

or lower, such as Gasoline, Propane, Natural

Gas or other similar fuel sources.

Diesel engine exhaust and some of its constitu-

ents are known to the State of California to cause

cancer, birth defects, and other reproductive harm.

DANGER

— CALIFORNIA —

Proposition 65 Warning:

OM944W3 6/17

1

Proprietary Information

This publication is the property of Alaska Diesel Electric, Inc.

It may not be reproduced in whole or in part without the written permission of Northern Lights, Inc.

Read this operator's manual thoroughly before starting to operate your equipment.

This manual contains information you will need to run and service your new unit.

OPERATOR'S MANUAL

for Northern Lights

®

M944W3 and M30CW3

Diesel Generator Sets

INTRODUCTION ..................................................2

Model Numbers ..................................................2

Serial Numbers ...................................................2

WARRANTY ...........................................................3

SAFETY RULES ..............................................3 - 7

LOCK OUT / TAG OUT INSTRUCTIONS...........8

COMPONENT LOCATIONS

Generator Set ...........................................10 - 11

CONTROL PANELS

Northern Lights Generator Sets ...................... 14

OPERATING PROCEDURES

Break-in Period ................................................ 15

Before Starting ................................................. 15

Starting ............................................................. 16

Operating ......................................................... 16

Stopping ........................................................... 16

Shutdowns and Alarms .................................... 17

Spare Parts ....................................................... 17

SERVICING SCHEDULE CHART ......... 18 - 19

SERVICING

Lubrication - General ....................................... 20

Checking Oil .................................................... 20

Oil Changes ..................................................... 20

Changing Oil Filter .......................................... 21

Air Filter .......................................................... 21

Table of Contents

SERVICING (Continued)

V-Belts ............................................................. 21

Valve Clearances .............................................. 22

Fuels - General ................................................. 23

Fuel Filters ....................................................... 23

Bleeding the Fuel System ................................ 24

Injector Service ................................................ 25

Injection Pump ................................................. 26

Cooling System ............................................... 27

Heat Exchanger ................................................ 28

Raw Water Pump ............................................. 28

Zinc Electrodes ................................................ 28

Electrical System - General ............................. 29

Booster Batteries .............................................. 29

Battery Care ..................................................... 30

Winterizing / Out-of-Service ........................... 30

TROUBLESHOOTING

Electrical .......................................................... 31

Engine ...................................................... 32 - 34

WIRING DIAGRAMS

AC Electrical ........................................... 35 - 36

DC Electrical ........................................... 37 - 44

Panel Diagrams ........................................ 45 - 51

OM944W3 6/17

2

The servicing of marine engines and generator sets

presents unique problems. In many cases, boats cannot

be moved to a repair facility. Marine engines cannot be

compared to the servicing of automobiles, trucks, or

even farm equipment. Failures often occur in remote

areas far from competent assistance. Marine engines are

taxed far more severely than auto or truck engines;

therefore, maintenance schedules must be adhered to

more strictly. Failures begin with minor problems that

are overlooked and become amplied when not corrected

during routine maintenance.

As operator, it is your obligation to learn about your

equipment and its proper maintenance. This is not a

comprehensive technical service manual. Nor will it make

the reader into an expert mechanic. Its aim is to aid you in

maintaining your unit properly.

Introduction

M - Northern Lights marine generator set

Model number of engine block

Bore Cylinders

94 mm 4

Serial Numbers

MODELS INCLUDED

This manual covers the operating instructions for:

M944W3 marine generator sets, which use the 944 engine block.

Model Numbers

Model numbers give the unit's application, block model, aspiration, and RPM:

+

Unit Identication

Northern Lights marine diesel generator set with a 944

engine and a PX-332K2 series generator end, Tier III.

M944W3

M 944

=

Your set has three serial numbers:

1

an engine number stamped on

a plate attached to the valve cover, 2 a generator end serial number,

and

3

a generator set serial number.

NOTE: Always use the generator set serial number when ordering parts

or in correspondence. The generator set serial number plate is found on

the service side of the generator and resembles the drawing in Figure 1.

Figure 1: Generator set

serial number plate.

Northern Lights marine diesel generator set with a 944 engine and a

PX-332K2 series generator end; commercial unit, 30 kW, Tier III.

M30CW3

=

OM944W3 6/17

3

A warranty registration certicate is supplied with your set. It entitles the original purchaser of our equipment

to a warranty covering material or assembly faults. The extent of coverage is described in the Limited Warranty

Statement. We recommend that you study the statement carefully.

NOTE: If the warranty is to apply, the servicing instructions outlined in this manual must be followed. If further

information is needed, please contact an authorized dealer or the factory.

Safety Rules

Warranty

Revised 6-5-17

IMPORTANT SAFETY INSTRUCTIONS.

Electromagnetic equipment, including generator sets

and their accessories, can cause bodily harm and

life threatening injuries when improperly installed,

operated or maintained. To prevent accidents be aware

of potential dangers and act safely.

READ AND FOLLOW ALL SAFETY

INSTRUCTIONS IN THIS MANUAL,

PRIOR TO THE INSTALLATION

OF ANY GENERATOR SET OR

ACCESSORY. KEEP THESE

INSTRUCTIONS FOR FUTURE

REFERENCE.

Recognize Safety Symbols and Instructions

In addition to the information found in this section, this

operator’s manual uses three dierent signal words to

outline potential dangers of a specic nature.

Follow All Safety Instructions

Carefully read and understand

all safety messages in this

manual and on your machine’s

safety signs. Keep signs in

good and clean condition.

Replace missing or damaged

signs. Be sure new equipment components and

repair parts include the current safety signs. For

replacement signs, proper placement of safety signs

or clarication on any safety issue, consult your

Northern Lights dealer or the factory.

There can be additional safety information contained

on parts and components from outside suppliers

that is not reproduced in this manual. Consult the

suppliers for additional safety information.

Learn how to operate the machine and how to use

the controls properly. Only trained personnel should

operate machines, or work on or around them.

Keep you machine in proper working condition.

UNAUTHORIZED MODIFICATIONS TO THE

MACHINERY MAY IMPAIR ITS FUNCTION

AND SAFETY PARAMETERS.

Prevent Bypass and Accidental

Starting

!

WARNING

Do not start engine by shorting across start terminal.

Engine will start if normal circuitry is bypassed,

creating a hazard by runaway machinery.

Start engine only from operator’s station.

!

DANGER

!

WARNING

!

CAUTION

DANGER indicates a hazardous situation which, if

not avoided, will result in death or serious injury.

WARNING indicates a hazardous situation which, if

not avoided, could result in death or serious injury.

CAUTION indicates a hazardous situation which,

if not avoided, could result in minor or moderate

injury.

NOTICE: Accident reports show that careless use of engines causes a high percentage of accidents.

You can avoid accidents by observing these safety rules. Study these rules carefully and enforce them on the job.

DANGER: Northern Lights generator sets and /or any other diesel powered equipment provided

by NLI is not provided with spark arresting or explosion proof components, and therefore is not

to be installed in the presence of combustible gases having a ash point of 43.3 Degrees C (110

Degrees F) or lower, such as Gasoline, Propane, Natural Gas or other similar fuel sources.

OM944W3 6/17

4

Safety Rules (Continued)

Revised 4-12-17

Wear Protective Clothing

!

WARNING

To prevent catching anything in moving machinery,

always wear close tting clothes and safety

equipment appropriate

to the job.

Prolonged exposure

to loud noise can

cause hearing loss or

impairment. Wear

suitable authorized

hearing protection,

such as earmus or plugs to protect against loud

noises.

Operating equipment requires the full attention of the

operator. Do not use radio or music headphones

while operating machinery.

Practice Safe Maintenance

!

CAUTION

Understand all service

procedures before starting work.

Keep area clean and dry. Never lubricate, service, or

adjust machine while it is in operation.

Keep hands, feet and clothing away from power-

driven equipment. When shutting down an engine,

disengage all power and operator controls. Allow

the engine to cool completely before beginning any

service work.

Securely support any machinery elements that must

be raised for service work with support or lifting

machinery specically intended for that purpose.

Keep all parts in good conditions and properly

installed. Fix damage immediately. Replace any

worn or broken parts. Remove any build up of

grease, oil or debris.

Disconnect battery ground cable (-) before making

any adjustments or service work.

Handle Fuel Safely - Avoid Flames

!

WARNING

Diesel is highly ammable and should be treated with

care at all times. Do do not refuel while smoking or

when near sparks or open ame.

ALWAYS STOP ENGINE BEFORE FUELING

MACHINE. Always ll

portable fuel tank outdoors.

Never fuel a hot engine.

Prevent accidental

discharge of starting uids

by storing all cans in a

cool, safe place, away

from sparks or open ame. Store with cap securely

on container. Never incinerate or puncture a fuel

container.

Prevent res by keeping machine clean of accumulated

trash, grease and debris. Always clean any spilled fuel

as swiftly as possible. Do not store oily rags, which

can ignite and burn spontaneously.

Be prepared if a re starts. Keep a rst aid kit and re

extinguisher handy. Keep emergency contact numbers

for re department, doctors, ambulance and hospital

near the telephone.

Service Machines Safely

!

DANGER

Do not wear a necktie, scarf, necklace, rings or other

jewelry, or any loose clothing

when working near moving

parts. Tie long hair behind your

head. If any of these items get

caught in moving machinery,

severe injury or death could

result.

Check for any loose electrical connections or faulty

wiring.

Look completely around engine to make sure that

everything is clear before starting.

OM944W3 6/17

5

Stay Clear of Rotating Drivelines

!

DANGER

Entanglement in rotating

drivelines can cause serious

injury or death. Keep

shields in place at all times. Make sure that rotating

shields turn freely in pace with the drivelines.

Do not wear loose tting equipment around rotating

drivelines. Stop the engine and make sure that

all moving parts have stopped before making any

adjustments, connections, or performing any other type

of service to the engine or other driven equipment.

Install all Safety Guards

!

WARNING

Direct contact with rotating

fans, belts, pulley and drives

can cause serious injury.

Keep all guards in place

at all times during engine

operation.

Wear close-tting clothes. Stop the engine and be

sure all fans, belts, pulleys and drives are stopped

before making adjustments, connections, or cleaning

near fans and their components.

Do not allow anything on your person to dangle into

or come in contact with a moving fan, belt, pulley or

drive. Fans can act as vacuums and pull materials

up from below, so avoid that area as well while in

service.

Safe Battery Handling

!

WARNING

Prevent Battery Explosions

Battery gas is highly ammable. Battery explosions

can cause severe injury or death. To help prevent

battery explosions, keep sparks, lighted matches

and open ame away from the top of battery. When

checking battery electrolyte level, use a ashlight.

Safety Rules (Continued)

Revised 4-12-17

Never check battery charge

by contacting the posts with

a metal object. Use a volt-

meter or hydrometer.

Frozen batteries may explode

if charged. Never charge

a battery that has not been

allowed to warm to at least

16

o

C (60

o

F).

Always remove grounded (-) battery clamp rst and

replace ground clamp last.

S

ulfuric acid in battery electrolyte is poisonous and

strong enough to burn skin, eat holes into clothing and

other materials, and cause blindness if splashed into eyes.

To Avoid Hazards:

• Fill batteries only in well-ventilated areas.

• Wear appropriate eye protection and rubber gloves.

• Never use air pressure to clean batteries.

• Wear appropriate ventilation equipment to avoid

inhaling fumes when adding electrolyte.

• Do not spill or drip electrolyte.

• Use correct jump-start procedure if required.

If acid is spilled on skin or in eyes:

1. Flush skin with water.

2. Apply baking soda or lime to

help neutralize acid.

3. Flush eyes with water for

15-30 minutes.

4. Get medical attention

immediately.

If acid is swallowed:

1. DO NOT induce vomiting.

2. Drink large amounts of

water or milk, without

exceeding 2 liters

(2 quarts)

3. Get medical attention

immediately

Battery posts, terminals, and related accessories

can contain lead and lead compounds, chemicals

known to the State of California to cause cancer and

reproductive harm. Wash hands after handling.

!

WARNING

OM944W3 6/17

6

Safety Rules (Continued)

Revised 4-12-17

Do not use a chlorinated solvent in an area where

welding will occur. Work only in areas that are well

ventilated. Dispose of paint and solvent properly.

Service Cooling System Safely

!

WARNING

Opening a pressurized cooling

system can release explosive uids

and causing serious burns.

Before opening any pressurized

cooling system, make sure the

engine has been shut o. Do

not remove a ller cap unless it

is cool enough to

comfortably grip with bare hands. Slowly loosen cap to

relieve pressure before opening fully.

Avoid High Pressure Fluids

!

WARNING

Relieve pressure prior to

disconnecting pressurized

lines. Escaping uid under

pressure can penetrate the

skin causing serious injury.

Always relieve pressure before disconnecting

hydraulic or other pressurized lines. Tighten all

connections rmly before re-applying pressure.

If searching for leaks, use a piece of cardboard.

Always protect your hands and other body parts from

high-pressure uids.

If an accident occurs, see a doctor immediately. Any

high pressure spray injected into the skin must be

removed within a few hours to prevent the risk of

gangrene or other infection.

Avoid Heating Near Pressurized Fluid Lines

!

WARNING

Flammable spray can be generated

by heating near pressurized uid

lines, resulting in severe burns and

bodily injury. Pressurized lines

can rupture when heat goes beyond

the immediate ame area. Do not weld, solder or use

a torch or open ame near pressurized lines or other

ammable uids.

Handle Chemical Products Safely

!

WARNING

Direct exposure to hazardous

chemicals can cause serious

injury. Among the potentially

hazardous chemicals that may be

used with Northern Lights

products are lubricants, coolants,

paints and adhesives.

All potentially hazardous chemicals come with a Material

Data Safety Sheet (MSDS). The MSDS provides specic

details on chemical products, including physical hazards,

safety procedures and emergency response techniques

Read and understand the MSDS for each chemical before

you start any job that includes it. Follow the procedures

and use appropriate equipment exactly as recommended.

Contact your Northern Lights dealer or Northern Lights

factory for MSDS’s used on Northern Lights products.

Work in Well Ventilated Areas

!

CAUTION

Exhaust fumes from engines contain carbon monoxide

and can cause sickness or death. Work in well ventilated

areas to avoid prolonged exposure to engine fumes. If it

is necessary to run an engine in an enclosed area, route

the exhaust fumes out of the area with an approved, leak

proof exhaust pipe extension.

Remove Paint Before Welding or Heating

!

WARNING

Hazardous fumes can be

generated when paint is heated

by welding, soldering or using a

torch. To avoid potentially toxic

fumes and dust, remove paint

before heating.

•

Remove paint a minimum of 100 mm (4 in.) from the

area that will be aected by heat.

•

If paint cannot be removed, wear an approved respirator.

• If you sand or grind paint, use an approved respirator.

• If you use solvent or paint stripper, remove stripper

with soap and water before welding. Remove

solvent or paint stripper containers from the area.

• Allow at least 15 minutes for fumes to disperse

before welding or heating.

OM944W3 6/17

7

Safety Rules (Continued)

Revised 4-12-17

Avoid creating dust. Never use compressed air for

cleaning. Avoid brushing or grinding materials

containing asbestos. When servicing, wear an

approved respirator. A special vacuum cleaner is

recommended to clean asbestos. If this vacuum is not

available, apply a mist of oil or water on the material

containing asbestos. Keep all bystanders away from

any area where asbestos dust may be generated.

Use Proper Lifting Equipment and Techniques

!

WARNING

Lifting heavy components incorrectly

can cause severe injury or damage

to machinery. Avoid unbalanced

loads. Do not use lifting eyes. Lift

the generator set using lifting bars inserted through

the lifting holes on the skid. Follow all recommended

removal and installation procedures in this and

associated Northern Lights manuals.

Use Proper Tools

!

CAUTION

Makeshift tools and procedures

can create safety hazards.

Always use appropriate tools for the job.

Use power tools only to loosen threaded parts and

fasteners. For loosening and tightening hardware,

always use the correct sized tools.

Do not use US measurement tools on metric

fasteners, or vice versa. Use only service parts that

meet Northern Lights specications.

Dispose of Waste Properly

!

CAUTION

Disposing of waste improperly can threaten the

environment and lead to unsafe working conditions.

Potentially harmful waste used in Northern Lights

equipment can include oil, fuel, coolant, lters and

batteries.

Use leakproof containers to drain uid. Do not

use food or beverage containers that may mislead

someone into drinking from them.

Do not pour waste onto the ground, down a drain or

into any water source.

Do Not Open High-Pressure Fuel System

!

DANGER

Many Northern Lights engines use high-

pressure fuel injection. High-pressure uid

remaining in fuel lines can cause serious

injury. Do not disconnect or attempt

any repair of fuel lines, sensors, or other

components between the high-pressure fuel pump

and nozzles on engines with high pressure fuel

systems.

ONLY AUTHORIZED TECHNICIANS CAN

PERFORM REPAIRS ON AN HIGH PRESSURE

FUEL INJECTION SYSTEMS.

Avoid Hot Exhaust

!

WARNING

Avoid exposure to and physical

contact with hot exhaust gases. Exhaust parts

and streams can reach high temperatures during

operation, leading to burns or other serious injury.

Cleaning exhaust lters can also lead to exposure to

hot exhaust gas and the injury risk associated with

it. Avoid exposure to and physical contact with hot

exhaust gases when cleaning exhaust lters.

During auto or manual/stationary exhaust lter

cleaning operations, the engine will run at

elevated temperatures for an extended period of

time. Exhaust parts and streams can reach high

temperatures during operation, leading to burns or

other serious injury.

Avoid Harmful Asbestos Dust

!

WARNING

Inhaling asbestos bers may

cause lung cancer. Avoid

breathing any dust that may

be generated when handling

components containing asbestos

bers, including some gaskets.

The asbestos used in these components is usually

found in a resin or otherwise sealed. Normal

handling of these components is not dangerous,

as long as airborne dust containing asbestos is not

generated.

OM944W3 6/17

8

General Policy

To avoid dangerous or hazardous situations, refrain from

any of the following:

• Removing or bypassing a guard or other safety device

• Placing any part of your body in a position where you

could be caught by moving machinery.

• Cleaning or oiling machinery when in operation.

• Adjusting circuits, chillers, pumps, air handlers, valves,

circuit breakers or fans while in operation.

• Working on piping or high pressure systems.

Lock Out/Tag Out Instructions -

Electrical Equipment

Be sure the equipment’s ON/OFF switch is in the OFF

position and is unplugged from any electrical source before

attempting to perform any type of work on the equipment.

Obtain an electrical plug cap cover with a lockset. Secure

the plug terminal end using the electrical plug lockout cap.

Lock the cap and retain the key.

If the equipment is directly wired into an electrical box with

a shut o switch, obtain a lock pad and/or the appropriate

colored tags and place the lock and tag through the shut

o lever. Retain the key until the repair is completed and

the machine is safe to start. Be certain the shut o lever

is in the OFF position before restarting. NEVER give a

lock out key to unauthorized personnel.

If the equipment is directly wired into an electrical box

without a shut o switch and lock out capability, then a

circuit breaker lock out will be required. Obtain a circuit

lock and tag set. Install the lock onto the circuit breaker

box. Ensure the unit ON/OFF switch is in the OFF position

before restarting.

Lock Out/Tag Out Instructions -

Pneumatic and Hydraulic Equipment

For servicing pneumatic and hydraulic equipment, the

following additional procedures must be implemented,

following completion of lock out/tag out procedures for

the unit to be serviced:

Shut o air, water or supply valves at the equipment to

be serviced.

Check the local bleed-o point for completed release of

pressurized air, water or oil.

If shutting o of air, water or other material cannot be

achieved at the local supply valve, shut o valves further

back in the system and re-check the bleed-o point until

complete shut-o is achieved.

Ax a DO NOT OPERATE tag to each valve handle that

requires shut o. Each DO NOT OPERATE tag must be

signed and dated by the authorized technician servicing

the equipment.

Lock Out/Tag Out Instructions -

Air Hose Connected Pneumatic Equipment

Equipment connected to the compressed air system

through an air hose with a detachable tting must be

shutdown and unplugged. Excess air must be bled prior

to removing the air hose, prior to any maintenance or

repair activities.

Ax a DO NOT OPERATE tag to the air hose near the

detachable tting. Each DO NOT OPERATE tag must be

signed and dated by the authorized technician servicing

the equipment. Check that the equipment cannot be

operated by activating the ON switch.

Stored Energy

Immediately after applying Lock Out or Tag Out devices,

ensure that all potentially hazardous stored or residual

energy is relieved, disconnected, restrained and otherwise

rendered safe.

Verication of Isolation

Verify the machinery or equipment is actually isolated and

de-energized prior to beginning work on a machine or on

equipment that has been locked out.

Restarting Procedures

Follow the procedures below prior to restoring energy:

• Ensure that all machinery or equipment is properly

reassembled. Inspect the machinery or equipment to

verify non-essential items have been removed.

• Ensure that all personnel are safely outside danger

zones. Notify personnel that lock out/tag out devices have

been removed and energy will be reapplied.

• Only authorized personnel may remove lock out/tag out

devices or notices.

Scope

During maintenance, repairs or retooling of a Northern Lights generator set, simply turning the machine o or unplugging

it while it is being worked on does not give enough protection to others who are not performing the maintenance or

repair. Many serious accidents happen when someone thought the machine was turned o, or all of its energy was

safely blocked or released.

!

CAUTION

!

WARNING

!

WARNING

!

WARNING

!

WARNING

!

CAUTION

!

CAUTION

Lock Out / Tag Out Procedures

Revised 4-12-17

OM944W3 6/17

9

added 11-12-12

Notes

OM944W3 6/17

10

Figure 2: M944W3 Service Side with PX-300K2 series generator end.

M944W3 Generator Set Component Locations

1. Expansion Tank

2. Coolant Fill

3. Rocker Arm Cover

4. Intake Manifold

5. Lube Oil Fill

6. Air Filter

7. Junction Box

8. Fuel Filter

9. Vibration Mounts

10. Lube Oil Dipstick

11. Fuel Manifold

12. Oil Filter

13. Fuel Primer Pump

14. Injection Pump

15. Lube Oil Drain

16. Thermostat Housing

17. Heat Exchanger Raw Water

Drain and Zinc

23. Raw Water Pump

1

2

3

4

5

6

7

8

9

1011

13

12

1415

16

17

23

5

OM944W3 6/17

11

M944W3 Generator Set Component Locations

Figure 3: M944W3 Non-Service Side with PX-300K2 series generator end.

18. AC Circuit Breaker

19. DC Circuit Breaker

20. Wet Exhaust Elbow

21. Exhaust Manifold

22. Heat Exchanger

23. Raw Water Pump

24. Belt Guard

25. Oil Pan

26. Alternator

27. Starter

18

19

20

21

22

24

25

26

27

23

OM944W3 6/17

12

1

2

3

4

5

6

7

8

9

10

11

13

12

14

15

16

17

23

5

Figure 2: M944W3 Service Side with PX-300K2 series generator end and new baseframe.

M944W3 Generator Set Component Locations

1. Expansion Tank

2. Coolant Fill

3. Rocker Arm Cover

4. Intake Manifold

5. Lube Oil Fill

6. Air Filter

7. Junction Box

8. Fuel Filter

9.

Fuel Supply &

Return Connections

10. Lube Oil Dipstick

11.

Intake Air Noise Reduction Tube

12. Oil Filter

13. Fuel Primer Pump

14. Injection Pump

16. Thermostat Housing

17. Heat Exchanger with Raw

Water Drain and Zinc

19. Vibration Isolating Mounts

23. Raw Water Pump

revised 9-24-12

OM944W3 6/17

13

M944W3 Generator Set Component Locations

Figure 3: M944W3 Non-Service Side with PX-300K2 series generator end and new baseframe.

15. Lube Oil Drain

18. AC Circuit Breaker

20. Wet Exhaust Elbow

21. Exhaust Manifold

22. Heat Exchanger

23. Raw Water Pump

24. Belt Guard

25. Oil Pan

26. Alternator

27. Starter

18

20

21

22

24

25

15

26

27

23

revised 9-24-12

OM944W3 6/17

14

Control Panels

Figure 4-B: Series 3 Generator Control Panel

Figure 4-A: Series 1-B Generator Control Panel

1. PREHEAT/ SHUTDOWN BYPASS

This switch serves two functions:

1. Preheats air before beginning the starting process.

Press switch for 10-20 seconds before attempting

startup.

2. Bypasses the safety shutdown feature during the

starting process. Keep switch engaged while starting

engine, and for 2 to 3 seconds afterwards, allowing oil

pressure to build beyond shutdown setpoint.

2. ENGINE CONTROL SWITCH

To start the engine, hold this switch in the START

position until the engine is running. After the engine

starts, release the switch and it will return to RUN

position. To stop the engine, hold the switch in the

STOP position.

NOTE: The rocker switch is used on Series 1 panels

only, and has a light that glows when the set is

running.

3. HOUR METER

Keeps track of engine running time.

4. OIL PRESSURE GAUGE

Shows the oil pressure in the engine lubricating system.

5. WATER TEMPERATURE GAUGE

Registers the temperature of the cooling water.

6. D.C. VOLTMETER

When the engine is stopped, the voltmeter indicates the

condition of the battery. When the engine is running,

the voltmeter indicates the voltage output of the

alternator.

For Series 4 Control Panels only:

7. A.C. VOLTMETER

Shows the generator output voltage.

8. FREQUENCY METER (Hertz)

The frequency meter indicates alternating current

frequency: 60 Hz (1800 rpm) or 50 Hz (1500 rpm).

9. AMMETER/VOLTMETER SELECTOR

Used to check the voltage and current of each phase.

Return to “Amps O” position when not monitoring.

10. A.C. AMMETER

Shows the generator load on each phase. The phase is

selected with the Ammeter Selector switch (#9).

Figure 4-C: Series 4 Generator Control Panel

OM944W3 6/17

15

Operating Procedures

BEFORE STARTING

1. Check the water level by removing the pressure

cap from the expansion tank. In order to give the

cooling water an opportunity to expand, the level

should be about 1 in. (2.5 cm) below the ller cap

sealing surface when the engine is cold.

CAUTION: Use protective clothing and open

the ller cap carefully when the engine is warm

to prevent burns.

2. Check the oil level in the crankcase with the

dipstick. The oil level must be between high and

low marks on the stick. Never allow the level to go

below this area. Always add the same viscosity of

oil as is already in the crankcase.

3. Check the fuel tank level and open any fuel valves

on the tank and at the secondary fuel lter.

4. Close the sea-cock, check and clean the sea strainer,

and reopen the sea-cock.

5. Place the battery switch in the ON position.

NOTE: The battery switch must always be kept ON

while the engine is running. If the switch is

turned OFF while the engine is running,

the battery charging alternator could be

damaged.

BREAK-IN PERIOD

1. The rst 100 hours on a new or reconditioned

engine are critical to its life and performance.

2. Operate the engine under various conditions,

particularly heavy loades with minimal idling, to

help seat engine components properly.

3. Constantly check the engine temperature and oil

pressure gauges.

4. Oil consumption is greater during break-in as

piston rings take time to seat.

5. Break-In Oil Changes: Change engine oil and

lter at 50 hours. Change oil and lter again at

100 hours (consult Lubricants section for oil

recommendation).

updated page 1-9-13

OM944W3 6/17

16

OPERATING

1. Units with Series 3 and Series 4 Control Panels:

check gauges often. Oil pressure must be above

15 PSI. The D.C. voltmeter should read between

11 and 15 volts at 80° F (25° C) ambient temperature.

The water temperature gauge must be below 200°

F (94° C). Check the A.C. voltage and frequency

meters (Series 4 panel). If the gauges deviate from

normal levels, shut down the generator set and

investigate.

2. Let the unit run unloaded for a three to ve minute

warm-up period.

3. Add electrical load.

STOPPING

1. Remove electrical load from the generator set.

2. Run the engine for a three to ve minute cool-down

period.

3. Move the Engine Control switch to the STOP

position until the engine stops completely.

4. Shut o seacock, fuel valve, and battery switch.

Operating Procedures

STARTING

1. Hold the Shutdown Bypass switch in the ON

position.

2. While holding the Shutdown Bypass switch in the

ON position, push the Engine Control switch to the

START position.

3. As soon as the engine starts, release both switches.

Do not crank the starter for more than 20 seconds

consecutively. If the engine fails to start with the

rst attempt, be sure that it has stopped completely

before re-engaging the starter.

NOTE: Excessive cranking of the starter on marine

   setsequippedwithawaterliftmuercan

cause engine damage. If the engine does not

start after 3 consecutive 20-second cranks,

remove the impeller from the seawater

   pump.Thiswillpreventthemuerfrom

   llingwithwaterandbackllingtheexhaust

line and engine. Once the engine starts, shut

   ifoimmediatelyandreinstalltheimpeller.

Restart and check the exhaust overboard

outlet for gushes of water.

OM944W3 6/17

17

SHUTDOWNS AND ALARMS

1. Your unit is tted with a system to protect it from

high water temperature, low oil pressure, and high

exhaust temperature.

a. Generator sets have shutdown systems to stop

the engine. They have no warning horns.

b. Other alarms and shutdowns are available as

optional equipment.

NOTE: If your unit is equipped with optional

shutdowns and alarms, do not rely on your

warning or shutdown system to the exclusion

of careful gauge monitoring. Watching your

gauges can prevent damage to the unit and

dangerous power losses.

2. Do the following when your warning or shutdown

system is activated:

a. Engage the preheat switch to check the

temperature gauge.

b. If above 205°F (96°C), use the Troubleshooting

Guide on page 25 to isolate the cause of the over-

heat.

CAUTION: Do not remove the water ll

cap of an overheated engine. Escaping high

temperature steam can cause severe burns. Allow

the engine to cool and then remove the cap slowly

using protective clothing.

c. Make repairs and restart after the temperature

gauge registers below 200° F (94° C).

d. Watch the temperature gauge regularly and

turn o the unit if the temperature rises above

205° F (96° C). Repeat troubleshooting.

3. If shutdown is activated and the temperature gauge

shows temperature within normal temperature range:

a. This shutdown could have happened because

of a too high exhaust temperature. This could

have been caused by a damaged impeller or a

partially blocked sea water strainer. Check the sea

water strainer rst. If it is clear, then check the

condition of the sea water pump impeller.

b. Check the engine crankcase oil level.

Operating Procedures

c. If the oil level is low, ll with recommended

lubricating oil and restart. Watch the oil pressure

gauge carefully and shut o the engine if it does

not show a normal reading (20-60 PSI) after a

few seconds of operation.

d. If the oil level is normal, DO NOT restart the

engine. Call your dealer for assistance.

SPARE PARTS

1. ADE recommends that you keep the following spare

parts on hand for eld service. The parts are

available from your local Northern Lights dealer.

Some marine models may already have “On-Board

Kits,” a handy box that contains the most common

parts you will need.

a. Primary and secondary fuel lter elements

b. Oil lters

c. Air lter elements

d. Alternator belt

e. Thermostat and gaskets

f. Seawater pump impeller and gaskets

g. Glow plugs

h. Injector and washer

2. If your set is operating a long distance from a

servicing dealer, add the following:

a. Complete set of injectors

b. Copper washers for injector change

c. Complete set of glow plugs

d. Fuel lift pump

page updated 8/27/09

Page is loading ...

Nothern Lights M30CW3 User manual

Nothern Lights M30CW3 User manual

Related papers

Other documents