PDP-MONITOR
(PLASMA DISPLAY PANEL)
PPM42M5S
PPM42M5H
PPM50M5H
PPM63M5H
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
ON-SCREEN MENUS
Picture In Picture (PIP)
VIDEO WALL
MDC
(Multiple Display Control)
Screen Burn Protection
Digital Natural Image engine
Intended for Commercial Use and Operation
Register your product at www.samsung.com/global/register
This device is a Class A digital apparatus.
BN68-00848B-00Eng_0420 4/20/05 6:26 PM Page 1
English - 2
User Instructions
◆ Screen Image retention
Do not display a still image (such as on a video game or when hooking up a PC to this PDP Monitor)
on the plasma monitor panel for more than 2 hours as it can cause screen image retention. This image
retention is also known as “screen burn”. To avoid such image retention, reduce the degree of
brightness and contrast of the screen when displaying a still image.
◆ Height
The PDP Monitor can normally operate only under 2000m in height. It might abnormally function at
a place over 2000m in height so do not install and operate there.
◆ Heat on the top of the PDP Monitor
The top side of the product may be hot after long periods of use as heat dissipates from the panel
through the vent hole in the upper part of the product.
This is normal and does not indicate any defect or operation failure of the product.
However, children should be prevented from touching the upper part of the product.
◆ The product is making a ‘cracking’ noise.
A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding
environment such as temperature or humidity. This is normal and not a defect of the unit.
◆ Cell Defects
The PDP Monitor uses a panel consisting of 1,230,000(SD-level) to 3,150,000(HD-level) pixels which
require sophisticated technology to produce. However, there may a few bright or dark pixels on the
screen. These pixels will have no impact on the performance of the product.
◆ Avoid operating the PDP Monitor at temperatures below 5°C(41°F)
◆ A still image displayed too long may cause permanent damage to the PDP Monitor Panel
Watching the PDP Monitor in 4:3 format for a long period of time may leave
traces of borders displayed on the left, right and center of the screen caused
by the difference of light emission on the screen.
Playing a DVD or a game console may cause similar effect to the screen.
Damage caused by the above effect are not covered by the Warranty.
◆ Afterimage on the Screen.
Displaying still images from Video games and PC for longer than a certain period of time may
produce partial afterimages.
To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images for a
long time.
◆ Warranty
- Warranty does not cover any damage caused by image retention.
- Burn-in is not covered by the warranty.
◆ Installation
Be sure to contact an authorized service center, when installing your monitor in a location with
heavy dust, high or low temperatures, high humidity, chemical substance and where it operates
for 24 hours such as the airport, the train station or etc.
Failure to do so may cause a serious damage to your monitor.
Installing the product in an airtight place may shorten the lifetime of the product.
BN68-00848B-00Eng_0420 4/20/05 6:26 PM Page 2
Owner’s Instructions
Remote Control/
AAA Batteries
Power Cord
PC Cable
Checking Parts
Install CD
- MDC Software (RS-232C)
PPM42M5S/
42M5H/50M5H
Stand-Base
(2EA)
Screws
(4EA)
English - 3
e
h
Ferrite Cores for
Speaker Wire (2EA)
(Refer to page 14)
BN68-00848B-00Eng_0420 4/20/05 6:26 PM Page 3
Contents
◆ FOREWORD
■ User Instructions............................................................................................ 2
◆ CONNECTING AND PREPARING YOUR DISPLAY
■ Control Panel................................................................................................. 6
■ Infrared Remote Control ................................................................................ 8
■ Inserting the Batteries in the Remote Control................................................ 9
■ Assembling the Stand-Base .......................................................................... 9
■ Installing the Display on the Wall Attachment Panel ..................................... 10
■ Installing the Display Vertically ...................................................................... 12
■ Before Using the Video Wall and the Multiple Display Control function ........ 12
■ Connecting Speakers .................................................................................... 13
■ Switching Your PDP Monitor On and Off....................................................... 15
■ Choosing Your Language.............................................................................. 15
◆ USING YOUR DISPLAY
■ Changing the Picture Standard ..................................................................... 16
■ Customizing the Picture Settings................................................................... 17
■ Adjusting the RGB Color (PC Mode) ............................................................. 18
■ Setting the Picture (PC Mode)....................................................................... 19
■ Using Zoom function (PC Mode) ................................................................... 21
■ Viewing the PC Information ........................................................................... 22
■ Selecting the Picture Size.............................................................................. 23
■ Freezing the Current Picture ......................................................................... 24
■ Changing the Sound Standard ...................................................................... 24
■ Extra Sound Settings..................................................................................... 25
■ Activating Panel Button Lock......................................................................... 26
■ Activating Remote Control Button Lock......................................................... 27
■ Setting Up Your Personal ID Number............................................................ 28
English - 4
BN68-00848B-00Eng_0420 4/20/05 6:26 PM Page 4
Contents (continued)
◆ USING YOUR DISPLAY (CONTINUED)
■ Setting the MDC (Multiple Display Control) ................................................... 29
■ Preventing Screen Burn-in ............................................................................ 30
■ Reducing the Effects of Screen Burn ............................................................ 31
■ Setting the Screen Burn Protection Timer ..................................................... 32
■ Setting the Multiple Screen............................................................................ 33
■ Displaying the Setting Information................................................................. 34
■ Setting and Displaying the Current Time....................................................... 34
■ Switching the PDP Monitor On and Off Automatically................................... 35
■ Selecting the Fan........................................................................................... 37
■ Setting the Film Mode.................................................................................... 38
■ Viewing the Picture in Picture (PIP)............................................................... 39
■ Listening to the Sound of the Sub Picture ..................................................... 41
■ Viewing an External Signal Source ............................................................... 42
◆ ADDITIONAL INFORMATION AND CONNECTIONS
■ Connecting to the Audio/Video Input............................................................. 43
■ Connecting to the S-Video Input.................................................................... 44
■ Connecting to the Component Input.............................................................. 44
■ Connecting to the DVD/DTV Receiver Input ................................................. 45
■ Connecting to the DVI Input .......................................................................... 46
■ Connecting to the PC Input ........................................................................... 46
■ Setting up Your PC Software (Windows only) ............................................... 47
■ Input Mode (PC/DVI) ..................................................................................... 48
■ Power Saver (PC1 mode only) ...................................................................... 49
◆ RECOMMENDATIONS FOR USE
■ Troubleshooting: Before Contacting Service Personnel................................ 50
■ Technical Specifications ................................................................................ 51
■ Dimension...................................................................................................... 52
☛
➢
Press Important Note
Symbols
English - 5
BN68-00848B-00Eng_0420 4/20/05 6:26 PM Page 5
➢
Control Panel
Front of the PDP Monitor
➢
The actual configuration of your PDP Monitor may be different,
depending on your model.
a)
b
c)
➢
d
➢
e)
➢
English - 6
➢
◆ You can use the
SEL ,
buttons to switch on the PDP Monitor when it is in standby
mode depending on the model.
◆ The VOL
-
,
+ and
SEL ,
buttons have the same function as the ▲/▼/œ/√ buttons
on the remote control.
◆ If the remote control no longer works or you have misplaced it, you can use the controls
on the panel of the PDP Monitor.
➢
➢
SOURCE
- Select the external input source.
- Store your settings in the menu.
- When the Main menu is displayed on screen,
the Main menu is not operated with source key.
MENU
Display the on-screen menu.
-
VOL +
- Adjust the volume.
- Adjust an option value respectively.
(VOL + : Enter to the selected menu.)
SEL
Control the cursor in the menu.
I /
Press to turn the PDP Monitor on and off.
a
Power Indicator
- Power Off; Black
- Power On; Green
b
Remote Control Sensor
Aim the remote control towards this spot on the
PDP Monitor.
c
Speaker Speaker
a b c
BN68-00848B-00Eng_0420 4/20/05 6:26 PM Page 6
Control Panel (continued)
➢
The actual configuration of your PDP Monitor may be different,
depending on your model.
Rear Panel
a) POWER IN
Connect the supplied power cord.
b) EXT SPEAKER (8Ω)
Connect external speakers.
c) PC1 IN/OUT
-
IN : Connect to the video output jack on your PC.
-
OUT : Connect to the video input jack on
external devices.
-
AUDIO : Connect to the audio output jack on
your PC.
➢
AUDIO is an audio input jack for PC1 and PC2
modes.
d) PC2 (BNC) IN
Connect for RGB(Y/PB/PR)HV video signal input from
the PC.
➢
“PC Mode” from this page onward means
PC1/PC2 mode using
RGB1(PC1) and
RGB2(PC2).
e) RS-232C
-
IN : Used for the MDC function when connecting
PC or RS-232C output of another PDP
Monitor.
-
OUT : Used for the MDC function when
connecting with RS-232C input of another
PDP Monitor.
➢
For further details about connections, refer to
Page 12.
f) DVI IN
-
DVI : Connect to the video output jack for device
with DVI output.
-
AUDIO : Connect to the audio output jack for
devices with DVI output.
g) COMPONENT IN
Video (Y/PB/PR) and audio (L/R) inputs for
component.
h) AV (VIDEO/AUDIO L/R)
-
IN : Video and audio inputs for external devices,
such as a camcorder or VCR.
-
OUT : Outputs for external devices.
i) S-VIDEO IN
Video input for external devices with an S-Video
output, such as a camcorder or VCR.
English - 7
➢
For further details about connection, refer to pages 43~46.
➢
Whenever you connect an audio or video system to your PDP Monitor, ensure that all elements are
switched off. Refer to the documentation supplied with your equipment for detailed connection
instructions and associated safety precautions.
c
BN68-00848B-00Eng_0420 4/20/05 6:26 PM Page 7
Infrared Remote Control
Y
yo
PDP MONITOR ON
DIRECT CHANNEL SELECTION
VOLUME INCREASE
TEMPORARY SOUND SWITCH-OFF
MENU DISPLAY
MOVE TO THE REQUIRED MENU
OPTION/
ADJUST AN OPTION VALUE
RESPECTIVELY
PICTURE EFFECT SELECTION
EXTERNAL INPUT SELECTION
EXIT FROM ANY DISPLAY
PREVIOUS CHANNEL
CONFIRM YOUR CHOICE
(STORE OR ENTER)
INFORMATION DISPLAY
PIP FUNCTIONS:
- PIP ACTIVATION OR DEACTIVATION
(PIP)
- SWAPPING THE MAIN AND THE SUB
PICTURE (SWAP)
- SIZE SELECTION (SIZE)
- SOURCE SELECTION (SOURCE)
PICTURE SIZE
NOT AVAILABLE
SETTING THE TIMER
AUTO ADJUSTMENT IN PC MODE
PDP MONITOR OFF
PICTURE STILL
SOUND EFFECT SELECTION
VOLUME DECREASE
NEXT CHANNEL
➢
The performance of the remote control may be affected by bright light.
➢
English - 8
BN68-00848B-00Eng_0420 4/20/05 6:26 PM Page 8
You must insert or replace the batteries in the remote control when
you:
◆ Purchase the PDP Monitor
◆ Find that the remote control is no longer operating
correctly
1 Remove the cover on the rear of the remote control by pressing
the symbol ( ) downwards and then pulling firmly to remove it.
2 Insert two R03, UM4, “AAA” 1.5V or equivalent batteries taking
care to respect the polarities:
◆
-
on the battery against
-
on the remote control
◆
+
on the battery against
+
on the remote control
3 Replace the cover by aligning it with the base of the remote
control and pressing it back into place.
Do not mix battery types, i.e. alkaline and manganese.
Inserting the Batteries in the Remote Control
Assembling the Stand-Base
1 Assemble the PDP Monitor with the stand and firmly
secure the PDP Monitor using 4 screws provided.
➢
Two or more people should carry the PDP Monitor.
Never lay the PDP Monitor on the floor because of
possible damage to the screen.
Always store the PDP Monitor upright.
English - 9
BN68-00848B-00Eng_0420 4/20/05 6:26 PM Page 9
English - 10
➢
◆
Installing the Display on the Wall Attachment Panel
Wall Bracket
Components
Plastic Hanger: 4 Screw : 11
Screw : 4
Anchor : 11
Wall Bracket Assembly
Installation Notes
◆
Contact a technician for installing the wall bracket.
◆
Samsung Electronics is not responsible for any damages to the product or harm to customers when
the installation is done by the customer.
◆
This product is for installing on cement walls. The product may not stay in place when installed on
plaster or wood.
Hinge
Accessories
➢
Refer to the correct installation guide according to your wall bracket.
1 Insert and tighten the Captive Screw in
the direction of the arrow.
When done, mount the wall bracket on
the wall.
2 Before drilling into the wall, check if the length
between the two locking holes at the back of
the product is correct.
If the length is too short or long, loosen all or
some of the 4 screws on the wall bracket to
adjust the length.
3 Check the installation diagram and mark the drill
points on the wall. Use the 5.0 mm bit to drill holes
deeper than 35 mm.
Fix each anchor in the corresponding hole.
Match each of the brackets and hinge holes to the
corresponding anchor holes and insert and tighten
the 11 screws .
Length between the
two locking holes
Captive Screw
Wall Bracket
Hinge (Right)
There are two hinges
(left and right). Use the
correct one.
Hinge (Left)
1 Left: 1 Right: 1
◆
Only use the components and accessories shipped with the product.
BN68-00848B-00Eng_0420 4/20/05 6:26 PM Page 10
English - 11
Installing the Display on the Wall Attachment Panel (continued)
1 Remove the 4 screws on the back of the product.
3 Tighten the 4 screws in step 2 (plastic hanger
+ screw ) to the rear holes of the product.
2 Insert the screw into the plastic hanger.
(See the figure below)
☛
◆ Mount the product on the wall bracket
and make sure it is properly fixed to
the left and right plastic hangers.
◆ Be careful when installing the product
on the bracket as fingers can be
caught in the holes.
◆ Make sure the wall bracket is securely
fixed to the wall, or the product may not
stay in place after installation.
4
Remove safety pin (#) and insert the 4 product
holders into the corresponding bracket holes (
!). Then
place the product (
@) so that it is firmly fixed to the
bracket. Make sure to reinsert and tighten the safety
pin (
#) to securely hold the product to the bracket.
Wall Bracket Angle Adjustment
➢
Adjust the bracket angle to -
2
o
before installing it on the wall.
◆ The shape of the product may vary depending on the model. (The assemblies of the plastic hanger
and the screw are the same)
PDP Monitor
Wall Bracket
Wall
1 Fix the product to the wall bracket.
2 Hold the product at the top in the center and pull it
forward (direction of the arrow) to adjust the angle.
(See the figure to the right)
3 You can adjust the bracket angle between -2° and 15°.
Make sure to use the top center,
and not the left or the right side of
the product to adjust the angle.
To mount the product on the wall bracket
t.
BN68-00848B-00Eng_0420 4/20/05 6:26 PM Page 11
Installing the Display Vertically
You can install the PDP Monitor vertically. In this case, the fan
automatically works. If you wish to stop the fan, position the PDP
Monitor horizontally and then set “
Fan” to “Off” in the
“
Function” menu.
Please use the wall attachment panel exclusively when installing
vertically. And you have to put left side of the PDP Monitor on top
when viewed from front.
Before Using the Video Wall and the Multiple Display Control function
Example for Multiple Display Control connections
1 Please create ID for each PDP Monitor before
installing them close together. It may be difficult to
create IDs when operating the remote control for
PDPs that are installed close to each other.
2 For details about Video Wall configuration and
operation, refer to “Setting the Multiple Screen”
on page 33.
➢
◆ You can connect a Composite (Video) without
a distributor as you would connect a PC.
◆ Select ID input on the menu. Use the numeric
buttons to enter the ID for PDP Monitor
adjustment. You can operate the remote
control only for the PDP Monitor that has been
selected.
◆ For details about Multiple Display Control, refer
to “Setting the MDC (M
ultiple Display Control)”
on page 29 and the Help section in MDC
program CD.
Example for 2x2 Video Wall function
Example for 2x2 Video Wall connections
Rear of the PDP Monitor Rear of the PDP Monitor
①
②
English - 12
➢
BN68-00848B-00Eng_0420 4/20/05 6:26 PM Page 12
Connecting Speakers
1 Remove the screws on the rear of the PDP Monitor.
2 Hang the two “T” shaped hangers
on the square holes on the rear of
the PDP Monitor.
3 Tighten the PDP Monitor and the speaker bracket using the screws removed from the PDP Monitor.
➢
When moving your PDP Monitor, do NOT hold the speaker connected to your PDP Monitor. It may
damage the bracket clamping the speaker and your PDP Monitor together and result in a drop of
your PDP Monitor and a risk of personal damage and injury.
PPM42M5S
PPM42M5H
PPM50M5H PPM63M5H
PPM42M5S
PPM42M5H
PPM50M5H
PPM63M5H
PPM42M5S
PPM42M5H
PPM50M5H PPM63M5H
p
English - 13
➢
Speakers are optional. You have to purchase the speakers
additionally.
BN68-00848B-00Eng_0420 4/20/05 6:26 PM Page 13
W
se
in
T
Connecting Speakers (continued)
Ferrite Cores
The ferrite cores are used to attenuate undesired signals.
When connecting cables, attach one of these ferrite cores to the cable
near the connector.
Connect the speaker audio cable to the external speaker output jack on the rear of the PDP Monitor
matching the “+” and “
-
” ends of the cable with the diagram on the PDP Monitor.
➢
◆ The speakers MUST have a power handling capability of 10 watts minimum (impedance 8Ω).
◆ When you connect the speaker wire to the external speaker out connector, first bind the
speaker wire round the ferrite core to secure it.
English - 14
BN68-00848B-00Eng_0420 4/21/05 2:56 PM Page 14
When you start using your PDP Monitor for the first time, you must
select the language which will be used for displaying menus and
indications.
1 Press the MENU ()button.
Result
: The main menu is displayed.
2 Press the … or † button to select Setup.
Result
: The Setup menu is displayed.
3 Press the ENTER () button.
4 Press the … or † button to select Language.
Press the
ENTER () button.
Result
: The available languages are listed.
5 Select the appropriate language by pressing the … or † button.
Press the
ENTER () button.
Choosing Your Language
The mains lead is attached to the rear of your PDP Monitor.
1 Plug the mains lead into an appropriate socket.
Result
: The Standby indicator on the front of the PDP Monitor
lights up.
➢
The main voltage is indicated on the rear of the PDP
Monitor and the frequency is 50 or 60Hz.
2 Press the “ ” button on the front of the PDP Monitor (or the ON
() button on the remote control) to switch the PDP Monitor on.
3 To switch your PDP Monitor off, press the “ ” button again (or
the
OFF () button on the remote control).
Front of the PDP Monitor
Switching Your PDP Monitor On and Off
English - 15
Time
√√
Language : English
√√
PC
√√
Setup
Move Enter Return
TV
Time
Language : English
PC
Setup
Move Enter Return
TV
English
Français
Deutsch
Italiano
Español
Português
††
BN68-00848B-00Eng_0420 4/20/05 6:28 PM Page 15
Y
co
You can select the type of picture which best corresponds to your
viewing requirements.
1 Press the MENU ()button.
Result
: The main menu is displayed.
2 Press the … or † button to select Picture.
Result
:
The
Picture menu is displayed.
3 Press the ENTER () button.
Result
:
The
Mode is selected.
4 Press the ENTER () button again.
Result
:
The available options are listed.
5 Select the required option by pressing the … or † button.
Result
: The following
options
are available.
◆ Dynamic - Standard - Movie - Custom
◆ Entertain - Internet - Text - Custom
: PC or DVI Mode.
6 Press the ENTER () button.
➢
You can also set these options simply by pressing the
P.MODE (Picture Mode) button on the remote
control.
Changing the Picture Standard
English - 16
Mode : Dynamic
√√
Custom
√√
Color Tone : Normal
√√
Color Control
√√
Film Mode : Off
√√
Size : 16:9
√√
PIP
√√
Picture
Move Enter Return
TV
Mode : Dynamic
Custom
Color Tone : Normal
Color Control
Film Mode : Off
Size : 16:9
PIP
Picture
Move Enter Return
TV
Dynamic
Standard
Movie
Custom
BN68-00848B-00Eng_0420 4/20/05 6:46 PM Page 16
Your PDP Monitor has several setting options that allow you to
control the picture quality.
1 Press the MENU ()button.
Result
: The main menu is displayed.
2 Press the … or † button to select Picture.
Result
:
The
Picture menu is displayed.
3 Press the ENTER () button.
Result
:
The
Mode is selected.
4 Press the … or † button to select Custom.
Press the
ENTER () button.
5 Select the required option by pressing the … or † button.
Result
: The following options are available.
◆ Contrast - Brightness - Sharpness - Color -
Tint (NTSC only)
◆ Contrast - Brightness : PC or DVI Mode.
6 Press the ENTER () button.
Result
: The horizontal bar is displayed.
Press the
œ or √ button until you reach the optimal
setting.
➢
◆ Press the … or † button to select other option(s).
◆ When the picture mode is set to Custom, the settings
values may vary depending on the input source.
(ex. AV, Component, PC, or DVI.)
7 Press the ENTER () button.
8 Press the MENU () button to return to the Picture menu.
Press the
… or † button to select Color Tone.
Press the
ENTER () button.
9 Select the required option by pressing the … or † button.
Result
: The following
options
are available.
◆ Cool2 - Cool1 - Normal - Warm1 - Warm2
◆ Custom - Cool - Normal - Warm : PC Mode.
◆ Cool - Normal - Warm : DVI Mode.
10 Press the ENTER () button.
Customizing the Picture Settings
English - 17
Contrast 100
Mode : Dynamic
√√
Custom
√√
Color Tone : Normal
√√
Color Control
√√
Film Mode : Off
√√
Size : 16:9
√√
PIP
√√
Picture
Move Enter Return
TV
Mode : Dynamic
√√
Custom
√√
Color Tone : Normal
√√
Color Control
√√
Film Mode : Off
√√
Size : 16:9
√√
PIP
√√
Picture
Move Enter Return
TV
Mode : Dynamic
Custom
Color Tone : Normal
Color Control
Film Mode : Off
Size : 16:9
PIP
Picture
Move Enter Return
TV
Contrast 100
Brightness 45
Sharpness 75
Color 55
Tint G 50 R 50
Custom
Move Enter Return
TV
Cool2
Cool1
Normal
Warm1
Warm2
BN68-00848B-00Eng_0420 4/20/05 6:46 PM Page 17
Adjusting the RGB Color (PC Mode)
English - 18
➢
1 Press the MENU ()button.
Result
: The main menu is displayed.
2 Press the … or † button to select Picture.
Result
: The Picture menu is displayed.
3 Press the ENTER () button.
4 Press the … or † button to select Color Tone.
Press the
ENTER () button.
5 Press the … or † button to select Custom.
Press the
ENTER () button.
➢
This feature is not available when the input source is DVI
mode.
6 Press the … or † button to select Color Control.
Press the
ENTER () button.
7 Select the required option (Red, Green, or Blue) by pressing the
… or † button.
8 Press the ENTER () button.
Result
: The horizontal bar is displayed.
Press the œ or √ button until you reach the optimal
setting.
➢
Press the … or † button to select other option(s).
9 Press the ENTER () button.
➢
Preset to the PC mode by pressing the SOURCE () button.
Mode : Entertain
√√
Custom
√√
Color Tone : Custom
√√
Color Control
√√
Film Mode : Off
√√
Size : 16:9
√√
PIP
√√
Picture
Move Enter Return
TV
Mode : Entertain
√√
Custom
√√
Color Tone : Custom
√√
Color Control
√√
Film Mode : Off
√√
Size : 16:9
√√
PIP
√√
Picture
Move Enter Return
TV
Red 50
Green 50
Blue 50
Color Control
Move Enter Return
TV
Red 50
BN68-00848B-00Eng_0420 4/20/05 6:46 PM Page 18
Setting the Picture (PC Mode)
English - 19
1 Press the MENU ()button.
Result
: The main menu is displayed.
2 Press the … or † button to select Setup.
Result
: The Setup menu is displayed.
3 Press the ENTER () button.
4 Press the … or † button to select PC.
Press the
ENTER () button.
Result
: The PC menu is displayed.
5 Press the ENTER () button again to select Auto Adjustment.
Result
: The screen quality and position are automatically reset.
The settings are all finished, and the PDP Monitor will
automatically return to the previous picture.
6 Press the … or † button to select Image Lock.
Press the ENTER () button.
7 Press the … or † button to select the option (Coarse or Fine) to
be adjusted. Press the
ENTER () button.
Result
: The horizontal bar is displayed.
Press the
œ or √ button until you reach the optimal
setting.
➢
Press the … or † button to select other option(s).
8 Press the ENTER () button.
➢
Preset to the PC mode by pressing the SOURCE () button.
Time
√√
Language : English
√√
PC
√√
Setup
Move Enter Return
TV
Auto Adjustment
√√
Image Lock
√√
Position
√√
Zoom
√√
Information
√√
PC
Move Enter Return
TV
Auto Adjustment
√√
Image Lock
√√
Position
√√
Zoom
√√
Information
√√
PC
Move Enter Return
TV
Coarse 50
√√
Fine 65
√√
Image Lock
Move Enter Return
TV
Auto Adjustment in Progress.
Please wait.
i
Coarse 50
BN68-00848B-00Eng_0420 4/20/05 6:46 PM Page 19
9 Press the MENU ()button.
Result
: The
PC menu is displayed again.
10 Press the … or † button to select Position.
Press the
ENTER () button.
11 Adjust the position by pressing the …, †, œ, or √ button.
12 Press the ENTER () button.
➢
Preset to the PC mode by pressing the SOURCE () button.
English - 20
Setting the Picture (PC Mode) (continued)
Auto Adjustment
√√
Image Lock
√√
Position
√√
Zoom
√√
Information
√√
PC
Move Enter Return
TV
Position
Adjust Return
TV
➢
BN68-00848B-00Eng_0420 4/20/05 6:46 PM Page 20
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
