Dynabrade 52657 Operating instructions

Brand: Dynabrade

Model: 52657

Category: Power tools

Type: Operating instructions

SAFETY INSTRUCTIONS

Carefully Read all instructions before operating or servicing any Dynabrade

Abrasive Power Tool.

Products offered by Dynabrade are not to be modified, converted or otherwise altered from the original design without expressed written consent from Dynabrade, Inc.

Tool Intent: 7" Right Angle Sanders are ideal for material removal using abrasive discs with appropriate back-up pads.

Do Not Use Tool For Anything Other Than Its Intended Applications.

This power tool is not intended for use in potentially explosive atmospheres and is not insulated against contact with electrical power.

Training: Proper care, maintenance, and storage of your air tools will maximize their performance.

• Employer's Responsibility – Provide 7" Right Angle Sander operators with safety instructions and training for safe use of tools and accessories.

Accessory Selection:

• Warning: DO NOT use cut-off wheels, saw blades, grinding wheels or flap discs. See tool intent for recommended accessory.

• Follow tool specifications chart before choosing size and type of accessory.

• Back-up Pad/Abrasive RPM (speed) rating MUST be approved for AT LEAST the tool RPM rating.

• Only use recommended fittings and air line sizes. Air supply hoses and air hose accessories must have a minimum working pressure of 150 PSIG (10 Bars, g) or 150 percent of the maximum

pressure produced in the system, whichever is higher. (See Machine Specifications table on back cover.)

(continued on next page)

Parts Page Reorder No. PD09•34R

Effective June, 2009

Supersedes PD09•15

7" Right Angle Sander

Air Tool Manual – Safety, Operation and Maintenance

WARNING

Read and understand tool manual before

work starts to reduce risk of injury to

operator, visitors, and tool.

WARNING

Eye protection must be worn at all times,

eye protection to conform to ANSI Z87.1.

WARNING

Respiratory protection to be used when exposed to

contaminants that exceed the applicable threshold

limit values required by law.

WARNING

Air line hazard, pressurized supply lines and flexible

hoses can cause serious injury. Do not use damaged,

frayed or deteriorated air hoses and fittings.

SAVE THIS DOCUMENT, EDUCATE ALL PERSONNEL

SAFETY LEGEND

WARNING

Practice safety requirements. Work alert,

have proper attire, and do not operate tools under

the influence of alcohol or drugs.

WARNING

Ear protection to be worn when exposure to sound,

exceeds the limits of applicable Federal, State or

local statues, ordinances and/or regulations.

Read and understand this tool manual before operating your air tool. Follow all safety rules for the protection of operating personnel

as well as adjacent areas. Always operate, inspect and maintain this tool in accordance with the American National Standards

Institute (ANSI) Safety Code for Portable Air Tools – B186.1. For additional safety information, refer to Safety Requirements for the

Use, Care and Protection of Abrasive Wheels – ANSI B7.1, Code of Federal Regulation – CFR 29 Part 1910, European Committee for

Standards (EN) Hand Held Non-Electric Power Tools – Safety Requirements and applicable State and Local Regulations.

WARNING

Some dust created by grinding, sanding, drilling, and other construction activities contain chemicals known to cause cancer, birth

defects or other reproductive harm. Some examples of these chemicals are:

• Lead from lead-based paints

• Crystalline silica from bricks and cement and other masonry products

• Arsenic and chromium from chemically treated lumber

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well

ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

FIND THE MOST CURRENT OFFERING OF SUPPORT DOCUMENTS AND ACCESSORIES @ WWW.DYNABRADE.COM

Model Wheel Size RPM Spindle Thread

52657 7" 6,000 5/8"- 11

52802 7" 7,200 5/8"- 11

53868 7" 8,500 5/8"- 11

OPERATING INSTRUCTIONS

Warning: Always wear eye protection. Operator of tool is responsible for following: accepted eye, face, respiratory, hearing and body protection.

Caution: Hand, wrist and arm injury may result from repetitive work, motion and overexposure to vibration.

• Keep hand and clothing away from working end of the air tool which has a potential hazard of cutting and severing.

Operation: Be sure that any loose clothing, hair and all jewelry is properly restrained.

• Secure inlet bushing on air tool with a wrench before attempting to install the air fitting to avoid damaging housing assembly.

• BEFORE MOUNTING A BACK-UP PAD/ABRASIVE, after all tool repairs and whenever a sander is issued for use, check tool RPM (speed) with tachometer with air pressure set at 90 PSIG

while the tool is running. If tool is operating at a higher speed than the RPM marked on the tool housing, or operating improperly, the tool must be serviced and corrected before use.

Warning: Back-up pad speed rating must be approved for at least the tool RPM rating. Check accessory manufacturer for details on maximum operating speed or special mounting instructions.

• Connect tool to air source. Be careful NOT to depress throttle lever in the process. Do not expose air tool to inlet pressure above 90 PSIG or (6.2 Bars).

Warning: After installing the back-up pad/abrasive, make sure that no one is in the unguarded plane before starting the sander. IN A PROTECTED AREA, test run the sander at a reduced speed to

check for good balance. Gradually increase tool speed. DO NOT USE if tool vibration is excessive. Correct cause, and retest to insure safe operation. Test sander at its free speed (RPM) in a protected

area for at least one minute before use.

• DO NOT engage spindle lock while spindle is rotating.

• Make sure that work area is uncluttered, and visitors are at a safe range from the tools and debris.

• Air tools are not intended for use in explosive atmospheres and are not insulated for contact with electric power sources.

• Use a vise or clamping device to hold work piece firmly in place.

• Do not apply excessive force on tool or apply "rough" treatment to it.

• Always work with a firm footing, posture and proper lighting.

• Ensure that sparks and debris resulting from work does not create a hazard.

• Always be aware of bystanders in work areas.

• This tool has side exhaust, rotate muffler cover by hand to desired exhaust direction. Exhaust may contain lubricants, vane material, bearing grease, and other materials flushed through the tool.

Warning: Sanding certain materials can create explosive dust. It is the employers responsibility to notify the user of acceptable dust levels. Reduce the risk by using dust collection systems and

personal protective equipment.

• Sanding can cause sparks which can cause fires or explosions. It is the users responsibility to make sure the work area is free of flammable materials.

• Use side handle provided to best control tool during sanding.

• Release the throttle lever in case of an interruption of the energy supply.

Report to your supervisor any condition of the tool, accessories, or operation you consider unsafe.

Back-Up Pad/Abrasive Mounting

• Disconnect air source from the tool.

• Clean spindle and locking flange nut mounting surfaces. Inspect for nicks,

cuts, sharp edges and thread wear.

• Install back-up pad onto spindle (ideal mounting is shown) with abrasive disc mounted

and locking flange nut secured. Spindle end should be flush with locking flange nut with

+ or - 1/16". Spacers may be needed to achieve ideal mounting.

• Check mounting by rotating spindle, make certain abrasive disc is concentrically

mounted and back-up pad is not excessively warped.

Side View

Spindle

Tool Housing

1/4" MAX. overhang

of abrasive disc

Abrasive Disc

Lock Flange Nut

Back-Up Pad

Optional Spacer(s)

Filter

Regulator

Lubricator

Lubricator Setting

90 PSIG

(6.2 Bar)

Air Flow to Tool Station

Ball

Valve

Ball

Valve

Air Flow

Drain

Valve

Drain

Valve

Air Tool

Air Compressor and Receiver

Drain Valve

Air Hose

90 PSIG Max.

(6.2 Bar)

Air Flow

Refrigerated

Air Dryer

• Dynabrade Air Power Tools

are designed to operate at 90

PSIG (6.2 Bar) maximum air

pressure at the tool inlet,

when the tool is running. Use

recommended regulator to

control air pressure.

• Ideally the air supply should

be free from moisture. To

facilitate removing moisture

from air supply, the installation

of a refrigerated air dryer after

the compressor and the use of

drain valves at each tool

station is recommended.

‰

CLOSED LOOP AIR SYSTEM

Sloped in Direction of Air Flow

‰

1 Drop/Minute per 20 SCFM

Maintenance Instructions

Important: To keep tools safe a Preventative Maintenance Program is required whenever portable power tools are used. The program shall include

inspection of air supply lines, air line pressure, proper lubrication and repair of tools. Refer to ANSI B186.1 and EN 792 for additional maintenance information.

•

Use only genuine Dynabrade replacement parts to insure quality. To order replacement parts, specify Model#, Serial# and RPM of your air tool.

•

It is strongly recommended that all Dynabrade rotary vane air tools be used with a Filter-Regulator-Lubricator to minimize the possibility of misuse due

to unclean air, wet air or insufficient lubrication. Dynabrade recommends the following: 10681 Air Line Filter-Regulator-Lubricator — Provides accurate air

pressure regulation, two-stage filtration of water contaminants and micro-mist lubrication of pneumatic components

•

Lubricate wick system through the angle gear oil fitting with 2-3 plunges for every 24 hours of use, to achieve maximum gear life.

Important: Use only the recommended angle gear oil for the wick system. Do not contaminate the wick with any other oil or grease product.

(Order 95848 Gear Oil and 95541 Gun) Always prime pump to insure good flow before lubricating gears.

•

Dynabrade recommends one drop of air lube per minute for each 20 SCFM (example: if the tool specification states 40 SCFM, set the drip rate on the

filter-lubricator to 2 drops per minute). Dynabrade Air Lube (P/N 95842: 1 pt 473 ml) is recommended.

Routine Preventative Maintenance:

•

Check free speed of tool using a tachometer without abrasive accessory attached with 90 PSIG at inlet while tool is running. This governor controlled tool

should be speed checked every 20 hours of use or weekly, whichever occurs more frequently. Always check tool speed after any maintenance or repair.

•

Take special care when performing any maintenance to the governor, the governor is preset at the factory to maintain the maximum rated speed for the

tool, if any inconsistency is found in the operating speed the tool must not be used. Investigate the cause, repair and recheck the free speed before use.

•

Inspect pad backing for excessive wear, nicks, cracks and cuts at the pad edges. Do not use pads that show excessive wear.

Check pad backing for concentricity.

•

Visually inspect abrasive discs for nicks, cuts, tears at the edges. Abrasive disc with a curved shape indicates improper storage. Do not use abrasives that

show these characteristics.

•

Mineral spirits are recommended when cleaning the tool and parts. Do not clean tool or parts with any solvents or oils containing acids, esters,

ketones, chlorinated hydrocarbons or nitro carbons.

•

DO NOT clean or maintain tools with chemicals that have a low flash point (example: WD-40

•

A Motor Tune-Up Kit (P/N 96100) is available which includes high wear and medium wear motor parts.

•

Air tool labels must be kept legible at all times, if not, reorder label(s) and replace. User is responsible for maintaining specification information i.e.:

Model #, S/N, and RPM. (See Assembly Breakdown)

•

Blow air supply hose out prior to initial use.

•

Visually inspect air hoses and fittings for frays, visible damage and signs of deterioration. Replace damaged or worn components.

•

Refer to Dynabrade's Warning/Safety Operating Instructions Tag (Reorder No. 95903) for safety information.

After maintenance is performed on tool, add a few drops of Dynabrade Air Lube (P/N 95842) to the air line and start the tool a few times to lubricate air motor.

Check for tool vibration before mounting abrasive wheel accessory.

Handling and Storage:

•

Use of tool rests, hangers and/or balancers is recommended.

•

Protect tool inlet from debris (see Notice below).

•

DO NOT carry tool by air hose. When carrying tool keep hands away from throttle lever to avoid accidental startup.

•

Protect abrasives accessories from exposure to water, solvents, high humidity, freezing temperature and extreme temperature changes.

•

Store abrasive discs prior to use at 40-50% relative humidity and 60-80˚ F (15-27˚ C) to reduce curling.

•

Store accessories in protective racks or compartments to prevent damage.

Notice

All Dynabrade motors use the highest quality parts and metals available and are machined to exacting tolerances. The failure of quality pneumatic motors

can most often be traced to an unclean air supply or the lack of lubrication. Air pressure easily forces dirt or water contained in the air supply into motor

bearings causing early failure. It often scores the cylinder walls and the rotor blades resulting in limited efficiency and power. Our warranty obligation is

contingent upon proper use of our tools and cannot apply to equipment which has been subjected to misuse such as unclean air, wet air or a lack of

lubrication during the use of this tool.

Lifetime Warranty

All Dynabrade portable pneumatic power tools are rigorously inspected and performance tested in our factory before shipping to our customers. If a

Dynabrade tool develops a performance problem and an inherent defect is found during normal use and service, Dynabrade will warrant this tool against

defects in workmanship and materials for the lifetime of the tool. Upon examination and review at our factory, Dynabrade shall confirm that the tool qualifies

for warranty status, and will repair or replace the tool at no charge to the customer. Normally wearable parts and products are NOT covered under this

warranty. Uncovered items include bearings, contact wheels, rotor blades, regulators, valve stems, levers, shrouds, guards, O-rings, seals, gaskets and

other wearable parts. Dynabrade’s warranty policy is contingent upon proper use of our tools in accordance with factory recommendations, instructions and

safety practices. It shall not apply to equipment that has been subjected to misuse, negligence, accident or tampering in any way so as to affect its normal

performance. To activate lifetime warranty, customer must register each tool at www.dynabrade.com. Dynabrade will not honor lifetime warranty on

unregistered tools. A one-year warranty will be honored on all unregistered portable pneumatic power tools. Lifetime warranty applies only to portable

pneumatic tools manufactured by Dynabrade, Inc. in the USA. Lifetime warranty applies only to the original tool owner; warranty is non-transferable.

7 N•m

17 N•m

23 N•m

9 N•m

Left Hand

Threads

25217 Muffler Assembly

Left Hand

Threads

See Label Key

Apply to

both sides

34 N•m

30 N•m

35 N•m

Index Key

No. Part # Description

1 25265 Retainer

2 53609 Felt Seal

3 25271 Spindle

4 01036 Bearing

5 98288 Shim (as required)

6 98287 Shim (as required)

7 Bevel Gear Set

25232 Models: 52657, 52802

25231 Model: 53868

8 25274 Spacer-

52657 & 52802

9 25264 Wick

10 02057 Bearing

11 98243 Wave Spring

12 25273 Plunger Assembly

(Includes 96156)

13 98285 Spring

14 Housing

(Includes: 01041 & 25275)

25203 Model 52657

25202 Model 52802

02208 Model 53868

15 25283 Silencer

16 25217 Muffler Assembly

17 98282 O-Ring (2mm)

18 98281 O-Ring (2.4mm)

19 25282 Silencer

20 25278 Muffler Cover

21 25281 Muffler Stem Assembly

22 53134

Vibration Dampening Handle

23 01007 Bearing

24 01294 Shim (as required)

25 01293 Shim (as required)

26 98242 O-Ring

27 25236 Front Bearing Plate

28 01010 Spacer

29 25233 Rotor

30 25234 Vane (4/Pkg.)

31 25235 Cylinder

32 96441 Pin

33 25237 Rear Bearing Plate

34 01206 Bearing

35 98279 Pin (2)

36 25290 Governor Cage

37 25291 Governor Weight (2)

38 25293 Governor Valve

39 Governor Spring

25296 Model 52657, 53868

25294 Model 52802

40 25298 Shim (.25 mm Thk.)

(asReq)

41 25299 Shim (.13 mm Thk.) (asReq)

42 25292 Governor Spindle

43 25295 Pin

44 66435 O-Ring

45 25256 Governor Housing

46 25257 Cup Nut

47 12132 Pin

48 01950 HD Safety-Lock Lever

49 25247 Valve Stem Assembly

(Includes 96443)

50 25245 Throttle Handle

(Includes 25246)

51 51945 Valve Seat

52 25249 Tip Valve

53 25250 Spring

54 96442 O-Ring

55 51940 Spacer

56 25213 Inlet Bushing

(Includes 51938, Qty-2 )

57 25253 Insulating Cover

58 51151 7" Back-Up Pad

Right Angle Sanders

Complete Assembly

Models:

52657, 52802, 53868

25285 S/N, RPM Label

25287 Sanding Label

Label Key

Part # Description

Adhesive: A

= Loctite #609

= Loctite #380

= Loctite #567

= Loctite #243

Torque: N•m x 8.85 = In. - lbs.

Oil: O

= Air Lube

Wicking: W

= Gear Oil

KEY

Disassembly/Assembly Instructions - Right Angle Sanders

Important: The Manufacturing Warranty is void if the tool is disassembled before the warranty expires by anyone other than a Dynabrade

Approved Repair Technician.

Notice: A 96100 Motor Tune-Up Kit is available. Also, the special repair tooling referred to in these instructions can be ordered through your Dynabrade

Distributor. Please refer to this tool manual for correct part number identification.

Important: Always follow these steps before servicing any part of this air tool.

1. Shut off the air supply, and depress throttle lever to dissipate the remaining air. Carefully disconnect the tool from the air supply hose.

Note: Use a wrench to hold the air tool inlet bushing stationary when removing the air supply connection.

2. Remove any abrasive product, flanging, guard, and side handle.

Motor Disassembly:

1. Use a 3mm drive punch to remove the throttle lever.

2. Roll back front edge of 25253 Insulating Cover just enough to expose wrench flats on 25257 Cup Nut.

3. Place padding around the housing and carefully hold the housing stationary in a vise. Use an adjustable wrench or 98283 Open End Wrench (

sold separately

) to loosen the

25257 Cup Nut. Turn counterclockwise. Note: Applying heat to cup nut will help loosen adhesive.

4. Carefully pull motor assembly out of the housing.

5. Hold pinion gear in a vise with aluminum or bronze jaws. Use an adjustable wrench to remove the governor assembly.

LEFT HAND THREAD Turn clockwise.

6. Fasten 96346 2" Bearing Separator around the portion of 25235 Cylinder that is closest to 25237 Rear Bearing Plate. Place the bearing separator motor on the table

of the 96232 #2 Arbor Press with pinion gear pointing downward. Use a 3/16" or 4mm diameter flat end drive punch push rotor out of the 01206 Bearing.

7. Remove the vanes from rotor and 01206 Bearing from bearing plate.

8. Fasten the vane slot portion of rotor in a vise with aluminum or bronze jaws so that the pinion gear is pointing up.

9. Use a hook/pin spanner wrench unthread pinion gear from rotor. Turn counterclockwise.

10. Remove the front bearing plate, shims and 01010 Spacer.

Motor Disassembly Complete.

Spindle/Gear Disassembly:

1. Place padding around the housing and carefully hold the housing stationary in a vise with the spindle pointing up. Use the 97782 Pin Wrench (

sold separately

) or an

adjustable pin wrench to remove 25265 Retainer. LEFT HAND THREAD Turn clockwise.

2. Remove 53609 Felt Seal from spindle or retainer.

3. Pull spindle and gear assembly out of the housing.

4. Fasten the 96346 2" Bearing Separator under 02057 Bearing and press spindle through bearing. Remove 25264 Wick.

Remove 98243 Wave Spring from the right angle housing.

5. Fasten the 96346 2" Bearing Separator between 01036 Bearing and spiral bevel gear. Place the bearing separator along with the spiral bevel gear assembly on the table of the

96232 #2 Arbor Press so that the spindle thread is pointing down. Push the gear off the spindle.

6. Remove the 01036 Bearing the same way.

7. Remove the housing from vise.

Spindle Disassembly Complete.

Spindle Lock Disassembly:

1. Apply a small amount of the Dynabrade Air Lube 10W/NR (P/N 95842 or equivalent) around the 25273 Plunger Assembly.

2. Place padding around the housing and carefully hold the housing stationary in a vise with the plunger assembly facing up.

3. Use two flat blade screwdrivers to pry the plunger assembly out of the 25275 Spindle Lock Bushing.

4. Remove the 98285 Spring and the 96156 Ring from the plunger.

Spindle Lock Disassembly Complete.

Valve Disassembly:

1. Secure 25245 Throttle Handle in a vise using wrench flats so that the 25213 Inlet Bushing pointing upward.

2. Use an adjustable wrench, unthread 25213 Inlet Bushing. Turn counterclockwise.

3. Use needle nose pliers, pull 25249 Tip Valve from handle.

4. Use a small screwdriver to remove the 96443 O-Ring from the valve stem and remove the valve stem.

5. Position 25245 Throttle Handle in the vise with 25257 Cup Nut and 25256 Governor Housing pointing up. Use a 10 mm hex key to remove the 25256 and

25257. Turn counterclockwise. Note: Applying heat to throttle handle will help loosen adhesive bond.

6. Push the 51945 Valve Seat out of the 25245 Throttle Handle.

Valve Body Disassembly Complete.

Important: Clean and inspect all parts for wear before assembling. Note: Follow all lubricant, adhesive, and torque specifications.

Valve Assembly:

1. Install 96443 O-Ring onto 25247 Valve Stem. Apply Dynabrade Air Lube to 96443 O-Ring and carefully install the valve stem and o-ring assembly into the

throttle handle. Note: Rotating the valve stem while inserting prevents damage to the o-ring

2. Apply several drops of the Dynabrade Air Lube 10W/NR (P/N 95842 or equivalent) to valve seat pocket wall on the inside of the 25245 Throttle Handle before inserting the

51945 Valve Seat. Install the 51945 Valve Seat by aligning the 3 male prongs of the valve seat with three slots of the valve seat pocket in the throttle handle. Note: Use an

arbor press and the 96241 Bearing Press Tool to support the valve seat and press it into the valve seat pocket. Make certain that the valve seat lays flat.

3. Use needle nose pliers install 25249 Tip Valve into the throttle handle.

4. Install 51940 Spacer onto 25213 Inlet Bushing, followed by the 96442 O-Ring. Install the larger end of the 25250 Spring into the inlet bushing. The smaller end of the

spring fits against the back of the tip valve.

5. Apply a small amount of the Loctite

#243 (or equivalent) to the external threads of the 25213 Inlet Bushing and install it onto the throttle handle. Secure throttle handle in a

vise using wrench flats. (Torque to 35N·m/310 lbs. in.)

6. Position the throttle handle in vise with the inlet bushing pointing downward.

7. Install the 66435 O-Ring onto the 25256 Governor Housing. Apply some Dynabrade Air Lube to the o-ring. Insert the governor housing through the 25257 Cup Nut. Apply a

small amount of the Loctite

#567 (or equivalent) to the external threads of the governor housing. Use a 10 mm hex key to fasten the governor housing and cup nut onto the

throttle handle. Turn clockwise. (Torque to 34N·m/300 lbs. in.) Note: The position of the throttle lever should be secured between the 9:00 to 11:00 o'clock position to best

protect the operator from unintentional starts.

8. Apply a few drops of Loctite

#380 (or equivalent) to both sides of the throttle handle (as shown). Install the 25253 Insulating Cover and the 01462 Throttle Lever onto

the throttle handle.

Valve Assembly Complete.

(continued on next page)

Disassembly/Assembly Instructions - Right Angle Sanders (cont.)

Spindle Lock Assembly:

1. Install a new 96156 Ring onto the plunger and apply a small amount of the Dynabrade Gear Oil (P/N 95848 or equivalent) to the o-ring and plunger.

2. Install 98285 Spring onto the housing bushing and insert the 25273 Plunger Assembly through the spring.

3. Install the plunger assembly into the spindle lock bushing. Note: Rotating the plunger while inserting prevents damage to the o-ring.

Spindle Lock Assembly Complete.

Motor Assembly:

1. Install 01010 Spacer onto the rotor front mandrel.

2. Select .003" (.08mm) thickness shims from the 01121 Shim Pack and install these into the 25236 Front Bearing Plate.

3. Install 98242 O-Ring into front bearing plate groove and install 01007 Bearing, into the front bearing plate.

4. Position the rotor in a vise with aluminum or bronze jaws so that the rotor spindle is pointing up. Install the front bearing/plate onto the rotor.

5. Apply a small amount of the Loctite

#243 (or equivalent) to the external threads on the rotor stem and install the pinion gear. (Torque to 17N·m/150 lbs. in.)

Using a hook/pin spanner wrench. Remove the assembly from the vise.

6. Use a .001" (0.3mm) thick feeler gauge to check the clearance between the front bearing plate and the face of the rotor. The clearance should be .001"-.0015" (0.3-0.4mm).

Note: If the clearance needs adjustment repeat steps 2-6 adding or removing shims as required.

7. Lubricate 25234 Vanes (4) with the 95842 Dynabrade Air Lube 10W/NR (or equivalent) and install these into the rotor.

8. Install 25235 Cylinder over the rotor so that the air inlet opening of the cylinder will line up with the air inlet opening on the 25237 Rear Bearing Plate.

9. Install 01206 Bearing into 25237 Rear Bearing Plate.

10. Use the raised inner diameter of 96244 Bearing Press Tool and the arbor press to install the rear bearing plate onto the rotor.

Note: Carefully press the bearing/plate down until it just touches the cylinder. This will establish a snug fit between the bearing plates and the cylinder.

11. Fasten the pinion gear in a vise with aluminum or bronze jaws so that the rear bearing/plate pointing up.

12. Apply a small amount of the Loctite

#567 (or equivalent) to the external threads of governor assembly. Install it onto the rotor using an 18 mm crowfoot and

torque wrench. LEFT HAND THREAD Turn counterclockwise. (Torque to 9N·m/80 lbs. in.)

13. Carefully slide the motor assembly into the housing.

14. Place padding around the housing and carefully hold the housing stationary in a vise. Apply a small amount of the Loctite

#567 (or equivalent) to housing external threads.

Use an adjustable wrench tighten 25257 Cup Nut onto housing. Turn clockwise. (Torque to 30N·m/265 lbs. in.)

Important: Allow 30 minutes for the adhesives to cure before operating the tool.

Run the tool to make sure that the air motor is functioning properly before installing the right angle gears. Motor Assembly Complete.

Spindle/Gear Assembly:

1. Position the spindle in the arbor press so that the threaded end is pointing down.

2. Use a 19/32" deep well socket as a press tool, install the 01036 Bearing onto the spindle and against the step.

3. Use a 19/32" deep well socket as a press tool and install the bevel gear onto the spindle.

4. Press 25274 Spacer onto the spindle and firmly against the shoulder.

5. Prepare the 25264 Wick by soaking in 95848 Gear Oil and then install wick onto the spindle against 25274 Spacer.

6. Press 02057 Bearing using 96243 Press Tool (

sold separately

) onto spindle until the spindle is flush with the bearing top.

7. Place padding around the housing and carefully hold the housing stationary in a vise with the right angle spindle opening facing up.

8. Place 98243 Wave Spring into housing pocket.

Important: Follow these steps to adjust the fit or “backlash” of the spiral bevel gear/pinion gear.

9. Install the spindle assembly into the housing align wick shape to housing contour. Mesh bevel and pinion gears together.

10. Apply a small amount of downward force on the spindle and rotate the spindle 360˚. The rotation should be smooth without any tight feel or binding of the gear teeth. Next,

rotate the spindle forward and backward to check the amount of backlash (free movement between the gear teeth). The correct fit should be minimal backlash without any

binding of the gear teeth. Add or remove shims to adjust the gear “backlash”.

11. Place the 53609 Felt Seal into the 25265 Retainer recess bore.

12. Apply a small amount of the Loctite

#567 (or equivalent) to the threads of the retainer and use the 97782 Pin wrench to install the retainer onto the housing.

LEFT HAND THREAD Turn counterclockwise. (Torque to 23N·m/203 lbs. in.)

13. Re-check the fit of the gears by hand before connecting the tool to the air supply. The correct fit should be minimal backlash without any binding of the gear teeth. Add or

remove shims to adjust the gear fit if necessary.

14. Use the 95541 Lubricant Gun to apply the 95848 Gear Oil Lubricant required for the lubricating wick prime the plunger before adding gear oil to housing. Inject three full

plunges of the gear oil into the 01041 Gear Oil Fitting on the front of housing.

Note: Inject three full plunges of gear oil into the lubricant fitting after operating the tool every 24-hour interval of use.

Right Angle Assembly Complete:

Muffler Assembly:

1. Install 25282 Silencer (Cross section size: 7.5 mm) up and inside recess diameter of 25278 Muffler Cover.

2. Install the 98281 O-Ring (Cross section size: 2.4 mm) into the inside groove of the muffler cover.

3. Install the 98282 O-Ring (Cross section size: 2.0 mm) into the outside groove of the muffler cover.

4. Install 25278 Muffler Cover (the side with the smaller hole) onto 25281 Muffler Stem Assembly.

5. Install 25283 Silencer (Cross section size: 13 mm) into housing cavity.

6. Apply a small amount of the Loctite

#243 (or equivalent) to the external threads of the 25281 Muffler Stem Assembly. Install the 25217 Muffler Assembly

onto the housing. Rotate 25281 Muffler Stem Assembly until slot aligns with housing raised boss. Thread socket head cap screw into housing using a 5/32" hex key

(Torque to 7N·m/60 lbs. in.).

Muffler Assembly Complete.

Final Assembly:

Important: Allow 30 minutes for the adhesives to cure before operating the tool. Install and properly position all guarding and auxiliary side handle. Before installing

mounting flanges or any abrasive product, the air tool must be tested for proper operation. Follow these steps to verify the correct rated operating speed of the tool.

1. Supply 3 drops of 95482 Dynabrade Air Lube 10W/NR (or equivalent) into the air inlet bushing of the tool while the throttle lever is depressed. Allowing the oil to flow into

the air motor.

2. Release the throttle lever.

3. With the air supply valve in the OFF position, carefully connect the tool to the air supply hose. Note: Use a wrench to hold the air inlet bushing on the tool stationary when

installing the air supply connection.

4. Once the tool is connected to the air supply, turn the supply valve to the ON position. Run the tool and use a tachometer to verify the rated operating speed (RPM) of the tool.

The tool should operate within 5% of the maximum rated RPM. The tool RPM must never exceed the maximum rated RPM with the operating air supply pressure reading 90

PSIG (6.2 bar g) at the air inlet of the tool. To adjust free speed add or remove shims. Adding shims will increase the speed, removing shims will reduce the tool free speed.

Once the correct rated operating speed for the tool is verified, disconnect the tool from the air supply and install the proper flanging and abrasive product.

Final Assembly Complete. Tool Assembly Complete.

This service chart is published as a guide to expectant life of component parts. The replacement levels are based on average tool

usage over one year. Dynabrade Inc. considers one year usage to be 1,000 hours.

Parts Common to all Models:

Preventative Maintenance Schedule

For Model All 7" Right Angle Sanders

Index Part Description Number High Wear Medium Wear Low Wear Non-Wear

# Number Required 100% 70% 30% 10%

1 25265 Retainer 1 X

2 53609 Felt Seal 1 X

3 25271 Spindle 1 X

4 01036 Bearing 1 X

5 98288 Shim 1 X

6 98287 Shim 1 X

See Note Bevel Gear Set 1 X

8 25274 Spacer 1 X

9 25264 Wick 1 X

10 02057 Bearing 1 X

11 98243 Wave Spring 1 X

12 25273 Plunger Assembly 1 X

13 98285 Spring 1 X

See Note Housing 1 X

15 25283 Silencer 1 T

16 25217 Muffler Assembly 1 X

17 98282 O-Ring 1 X

18 98281 O-Ring 1 X

19 25282 Silencer 1 T

20 25278 Muffler Cover 1 X

21 25281 Muffler Stem Assembly 1 X

22 53134

Vibration Dampening Handle 1 X

23 01007 Bearing 1 T

24 01294 Shim 1 T

25 01293 Shim 1 T

26 98242 O-Ring 1 T

27 25236 Front Bearing Plate 1 X

28 01010 Spacer 1 X

29 25233 Rotor 1 X

30 25234 Vane (4/pkg.) 1 T

31 25235 Cylinder 1 X

32 96411 Pin 1 X

33 25237 Rear Bearing Plate 1 X

34 01206 Bearing 1 T

35 98279 Pin 2 X

36 25290 Governor Cage 1 X

37 25291 Governor Weight 2 X

38 25293 Governor Valve 1 X

See Note Governor Spring 1 X

40 25298 Shim 1 X

41 25299 Shim 1 X

42 25292 Governor Spindle 1 X

43 25295 Pin 1 X

44 66435 O-Ring 1 T

45 25256 Governor Housing 1 X

46 25257 Cup Nut 1 X

47 12132 Pin 1 T

48 01462 Safety-Lock Lever 1 X

49 25247 Valve Stem Assembly 1 T

50 25245 Throttle Handle 1 X

51 51945 Valve Seat 1 X

52 25249 Tip Valve 1 T

53 25250 Spring 1 T

54 96442 O-Ring 1 T

55 51940 Spacer 1 X

56 25213 Inlet Bushing 1 X

57 25253 Insulating Cover 1 X

96100 – Motor Tune-Up Kit

LEGEND

T Included in Tune-Up Kit

X Type of wear, no other

comments apply.

L Easily lost. Care during

assembly/disassembly.

D Easily damaged during

assembly/disassembly.

R Replace each time tool is

disassembled.

Note: Please refer to page 4 for specific part number and description.

DYNABRADE

DYNABRADE, INC.,

8989 Sheridan Drive

•

Clarence, NY 14031-1490

•

Phone: (716) 631-0100

•

Fax: 716-631-2073

•

International Fax: 716-631-2524

Visit Our Web Site: www.dynabrade.com Email: Customer[email protected]

Optional Accessories

Dynabrade Air Lube

•

Formulated for pneumatic equipment.

•

Absorbs up to 10% of its weight in water.

95821: 4oz. (118 ml)

95842: 1pt. (473 ml)

95843: 1gal. (3.8 L)

98263 Male Plug - 3/8" NPT

•

Provides up to twice the air flow

compared to standard plug design.

•

Plug has “ported” design to prevent

“starving” of the air tool.

Dynabrade Angle Gear Oil

•

Specifically formulated to saturate wick system in right

angle gear head.

95848: 2.5 oz. tube

95541: Gear Oil Gun

96100 Motor Tune-Up Kit

•

Includes assorted parts to help

maintain and repair motor.

Additional Repair Tools (Not shown)

96244 - Bearing Press Tool

96243 - Bearing Press Tool

96346 - Bearing Separator

96208 - Repair Collar

97782 - Pin Wrench

Wrenches

98283 - Open End (1-5/8")

95281 - Open End (19mm)

95049 - Hex Key (3/16")

Dynaswivel

•

Swivels 360° at two locations which allows an

air hose to drop straight to the floor, no matter

how the tool is held.

95461 3/8" NPT.

FIND THE MOST CURRENT OFFERING OF SUPPORT DOCUMENTS AND ACCESSORIES @ WWW.DYNABRADE.COM

Machine Specifications

Model Motor Motor Sound Maximum Air Flow Spindle Air Pressure Weight Length Height

Number hp (W) RPM Level SCFM (LPM) Thread PSIG (Bars) Pound (kg) Inch (mm) Inch (mm)

52657 1.3 (969) 6,000 76 dB(A) 40 (1138) 5/8-11" male 90 (6.2) 4.5 (2.0) 10 (255) 3-9/16 (90)

52802 1.3 (969) 7,200 78 dB(A) 42 (1189) 5/8-11" male 90 (6.2) 4.5 (2.0) 10 (255) 3-9/16 (90)

53868 1.3 (969) 8,500 76 dB(A) 40 (1138) 5/8-11" male 90 (6.2) 4.5 (2.0) 10 (255) 3-9/16 (90)

Additional Specifications: Air Inlet Thread 3/8" NPT • Hose I.D. 3/8" (10mm)

Sound Level is the pressure measurement according to the method outlined in ISO regulation ISO-15744

Apply 2-3

plunges

into lubrication

fitting every

24 hours of

operation.

Expect a gear life

of 500 hours

minimum, with

proper lubrication.

Special Greasing Instructions

•

Lubricate wick system through the angle gear oil fitting with 2-3 plunges for every 24

hours of use, to achieve maximum gear life. Prime pump to insure good oil flow.

Important: Use only the recommended angle gear oil for the wick system.

Do not contaminate the wick with any other oil or grease product. Insure that all 3 plunges of

oil are injected through the fitting.

(Order 95848 Gear Oil and 95541 Gun)

American National Standards Institute (ANSI)

25 West 43 Rd St., 14th Floor • New York, NY 10036 • Tel: 1 (202) 293-8020

Compressed Air & Gas Institute

1300 Sumner Ave. • Cleveland, OH 44115-2851

Tel: 1 (216) 241-7333 • Fax. (216) 241-0105

European Committee for Standardization

Rue de Stassart 36 • B - 1050 Brussels, Belgium

International Organization of Standards

Case postale 56 • CH-1211 Geneva 20

Tel: + 41 22 749 01 11 • Fax: + 41 22 749 09 47

Government Printing Office

Superintendent of Documents • Attn: New Orders

P.O. Box 371954 • Pittsburgh, PA 15250-7954

Tel: 1 (202) 512-1803

REFERENCE CONTACT INFORMATION

Dynabrade 52657 Operating instructions

Brand: Dynabrade

Model: 52657

Category: Power tools

Type: Operating instructions

Download PDF

report

Dynabrade 52657 Operating instructions

Dynabrade 52657 Operating instructions

Related papers

Other documents