Proscenic M8 Pro User guide

Guide to set up M8/M8 PRO robot vacuum cleaner on the Proscenic APP

INDEX

1. Introduction for connecting to the app via WiFi

1) Download the "Proscenichome" app and log in.

2) Add Proscenic M8 Pro.

3) Watch the screenshots below to connect.

2. Introduction to Cleaning Mode

4) Adjustment of suction power and water flow speed.

5) Adjusting the suction power.

6) Adjusting the water flow speed.

3. Cleaning Mode Settings (Mode List)

7) Global Cleaning.

8) Partition Cleaning.

9) Area Cleaning.

10) Single Point Cleaning.

4. Prohibited Area setting.

11) Y-shaped cleaning mode.

12) Cleaning Program.

5. Introduction of other functions

13) Cleaning Records.

14) Device Sharing.

15) Parts Life Cycle.

16) Robot information.

17) Notification settings.

18) Manual control.

19) Unit settings.

6. Alexa/Google Home configuration

20) Alexa configuration

21) Google Home configuration

1. Introduction for connecting to the app via WiFi

Note: The screenshots were taken on an Android device but are similar for

Ios devices as well. There are two Proscenic apps in the App Store:

"ProscenicHome" and "Proscenic Robotic". "Proscenic Robotic" only works

for older generation robots (Suzuka, 790T and 811GB). So, download the

"ProscenicHome" APP to connect.

1.1 Download the "ProscenicHome" app and log in

1) Log in to the "ProscenicHome" app.

1.1.1 Register your "ProscenicHome" account with your email address or

phone number. Select "CA". Please note: If you already have a

"ProscenicHome" account, please skip this step.

1.1.2 Enter your username and password to log in with your

"ProscenicHome" account.

1.1.3Add the Proscenic M8 Pro.

Note: Make sure your device is connected to a 2.4Ghz WiFi network. If your

WiFi is 5Ghz, it probably has 2.4Ghz as well. So associate with the latter to

connect or go into your router settings.

1.1.3 Following the instructions in the screenshots below to turn on your robot

and proceed with activating pairing mode.

1.1.3 1.1.3Select the 2.4Ghz WiFi network (e.g. PDCN) and enter your WiFi

password. Then press the "Next" button.

1.1.4 On the WiFi settings page, switch from the 2.4Ghz Wifi network where

you are connected to the robot's Wifi network, i.e. the Wifi named

Proscenic-M8-xxxx. Then go back to "Proscenic". Now press the "Next"

button.

Note: The two buttons on the robot will change from flashing to solid

when the connection is successfully established. You will now be able

to control your Proscenic M8 Pro robot in "Proscenic".

2. Introduction to Cleaning Mode

2.1 Adjustment of suction power and water flow speed.

1) Adjusting the suction power.

The M8 PRO robot offers 4 levels of suction power:

Suction 0 (off).

Suction 1.

Suction 2.

Suction 3.

It can be applied in global cleaning, partition cleaning and area cleaning. Note:

When cleaning a spot, the robot will default to the maximum suction mode

(2700Pa).

10) Water flow speed adjustment.

The M8 PRO robot offers 4 levels of suction power:

Speed 0 (off)

Speed 1

Speed 2

Speed 3

It can be applied in global cleaning, partition cleaning, area cleaning and one

spot cleaning. If you only want to do vacuuming, please set the speed 0 or

remove the cloth holder.

2.1 Cleaning Mode Settings (Mode List)

1) Global cleaning

The M8 PRO robot starts cleaning the edge of your home first and then

continues with the interior cleaning. When finished, it will return to the

charging base (dust collector). In this mode, you can freely adjust the suction

mode and water speed flow.

2) Partition Cleaning

When the robot vacuum cleaner has finished cleaning once in the global

cleaning mode, it will automatically divide into partitions on the app.

You can also go into the settings and manage the partition management

yourself. Selecting an area already divided, you can set a partition, assigning

it a name, dividing or joining other areas of the house. In this mode, you can

freely choose the suction and water speed flow.

Note: You can manually subdivide (a division divides into two) the area (or

room) that has already been partitioned.

3) Area cleaning

You can select customize areas (name and adjust cleaning frequency) and

perform suction or suction and wash operations.

In this mode you can adjust the suction and water speed flow as you like.

Note: Provide settings in a rectangular and polygonal area.

4) Cleaning a point

Select a specific point on the map and your M8 PRO can go to the identified

square area with a diameter of 1.5m on the central point. It will start

vacuuming first along the edge of the square area and close in cleaning

inwards (default suction setting: 2700pa), vacuum twice and return to the

charging base to recharge.

2.1 Setting the Restricted Area.

You can set up multiple restricted areas (max. 15) and choose the most

suitable shape for your restricted areas (square or polygon). You can also

assign names, for example: forbidden area 1 and forbidden area 2. In this

way you can formalize your restricted areas.

2.1 Y-Shape Washing Mode.

Choose Y washing mode

2.5 Cleaning program

Method:

1. Choose the Cleaning Program in the settings.

2.Add the cleaning list: the cleaning time, the cleaning frequency, the

cleaning mode (Global Cleaning, Area Cleaning and Partial Cleaning) and

the frequency to empty dust automatically.

3.Tap the "save" symbol. This completes the setting process.

If you prefer, you can also turn on do not disturb mode.

2.1 More information in the settings

3. Introduction of other functions

Page is loading ...

Proscenic M8 Pro User guide

Related papers

Other documents