2. Kogan
  3. OVTHEOBFKGA
OVTHEOBFKGA

Kogan OVTHEOBFKGA User guide

  • Hello! I'm here to assist you with your Ovela Theodore Bed Frame assembly. I have reviewed the provided user guide which includes step-by-step instructions on putting together your king size bed frame. The guide details all components, hardware, and assembly process, including attaching legs, sideboards, slat supports and slats. Feel free to ask any questions related to this assembly process.
  • What should I do if any components are missing?
    What tools are needed for assembly?
    How many slats are included?
THEODORE BED FRAME
KING
OVTHEOBFKGA, OVTHEOBFKCA, OVTHEOBFKBA
A Headboard (x1)
B Footboard (x1)
C Upper sideboard (x2)
D Lower sideboard (x2)
E Upper slat support (x2)
F Lower slat support (x2)
G Sideboard leg support (x2)
H Leg support (x4)
I Horizontal slat support (x1)
J Sideboard rail (x4)
K Leg (x4)
COMPONENTS
Hardware
1 Allen key (x1)
2 50mm M8
screw (x2)
3 Nut (x10)
4 20mm M8
screw (x20)
5 40mm M4 screw (x4)
6 40mm M8
screw (x16)
7 Washer (x20)
8 T-handle Allen
key (x1)
9 Slat (x36)
10 Inner cap (x24)
11 End cap (x24)
12 Screwdriver (x1)
Remove all components from the packaging and check all components are accounted for.
If any components are missing, contact help.Kogan.com for assistance.
Step 1: Secure four legs (K) onto the headboard (A) and footboard (B).
ASSEMBLY
BEFORE ASSEMBLY
B
K
A
K
Step 2: Align one sideboard rail (J) with one lower sideboard (D). Place a washer (7) over the
hole at the end of the sideboard rail (J), then using the Allen key (1), secure a 40mm M8
screw (6) through the washer (7).
Using the screwdriver (12), secure a 40mm M4 screw (5) through the middle hole.
Repeat this process one more time to create two lower sideboard assemblies.
1 (x1)
5 (x2)
6 (x2)
7 (x2)
12 (x1)
x2
1
7
6
12
5
D
J
Step 3: Align one sideboard rail (J) with one upper sideboard (C). Place a washer (7) over
the hole at the end of the sideboard rail (J), then using the Allen key (1), secure a 40mm M8
screw (6) through the washer (7).
Using the screwdriver (12), secure a 40mm M4 screw (5) through the middle hole.
Repeat this process one more time to create two upper sideboard assemblies.
1 (x1)
5 (x2)
6 (x2)
7 (x2)
12 (x1)
x2
C
5
12
1
7
6
J
Step 4: Align one lower and upper sideboard assemblies with a sideboard leg support (G),
ensuring the sideboard leg support (G) is fitted behind the sideboard rails (J).
Place two washers (7) over the upper holes of the sideboard leg support (G), then using the
Allen key (1), secure two 40mm M8 screws (6) through the washers (7). Using the Allen key
(1), secure the lower holes with two 20mm M8 screws (4).
Repeat this process with the remaining lower and upper sideboard assemblies to create two
sideboard assemblies.
1 (x1)
4 (x4)
6 (x4)
7 (x4)
x2
7
6
1
4
D
C
G
J
Step 5: Connect one lower slat support (F) with one upper slat support (E), then align the
holes of two leg supports (H) with the lower and upper slat supports (F, E).
Place four washers (7) over the holes, then using the Allen key (1), secure four 40mm M8
screws (6) through the washers (7). Using the T-handle Allen key (8), secure the underside of
the holes with four nuts (3).
Repeat this process with the other lower and upper slat supports (E, F) to create two slat
support assemblies.
1
(x1)
3
(x8)
6
(x8)
7
(x8)
8
(x1)
x2
H
H
1
6
7
3
8
F
E
Step 6: Align the brackets on the sideboard assemblies with the headboard (A) and
footboard (B). Using the Allen key (1), secure the brackets with eight 20mm M8 screws (4).
1
(x1)
4
(x8)
1
4
A
B
Step 7: Align the slat support assemblies with the headboard (A) and footboard (B). Using
the Allen key (1), secure the slat support assemblies with eight 20mm M8 screws (4).
1
(x1)
4
(x8)
1
4
A
B
Step 8: Align the horizontal slat support (I) with the sideboard assemblies. On the ends of
the horizontal slat support (I), place two washers (7) over the holes on one side, then using
the Allen key (1), secure two 50mm M8 screws (2) through the washers (7). The screws (2)
should now be protruding out the other side.
On the other side, secure two washers (7) and two nuts (3) over the screws (2) using the
T-handle Allen key (8).
1 (x1)
2 (x2)
3 (x2)
7 (x4)
8 (x1)
I
1
2
7
8
3
7
Step 9: Connect two slats (9) with two end caps (11) and two inner caps (10) to create a slat
assembly. Repeat this process until you have twelve slat assemblies.
Secure the slat assemblies by aligning the holes on the end caps (11) and inner caps (10)
with the markers on the bed.
9 (x36)
10 (x24)
11 (x24)
x12
11
9
10
9
10
9
11
Assembly is complete.
NOTES
Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com
/