iGear iG-PO1 User manual

Brand: iGear

Model: iG-PO1

Type: User manual

iGear iG-PO1 is a compact and lightweight fingertip pulse oximeter designed to measure blood oxygen saturation (SpO2) and pulse rate accurately. Its advanced DSP algorithm minimizes the effects of motion artifacts, ensuring precise readings even under low perfusion conditions. With a colorful LED display and four display directions, it allows for easy viewing from different angles. The device operates on two AAA batteries, providing up to 16 seconds of continuous use before automatically turning off to conserve power.

Model No.: iG-PO1

General instructions

The Fingertip Pulse Oximeter is used to detect the

blood oxygen saturation and pulse rate of the

human body. This product is based on digital blood

oxygen technology and uses an advanced DSP

algorithm to reduce the effects of motion artifacts

and improve the measurement accuracy under

weak perfusion.

Technical Parameters

Display mode: Colourful LED display, 4 display

directions.

Power supply: 1.5 V (AAA size) alkaline batteries x2

Working current: 30mA

Measurement performance under weak perfusion

Conditions: 0.3%

Measuring Speciﬁcations:

Oxygen Saturation (SpO2)

Measuring range 0-100%

Resolution 1%

Accuracy 70~100%, 2%, 0-69%

Pulse Rate

Measuring range 25-250 bpm

Resolution 1 bpm

Accuracy 2 bpm

Features

• The product is simple and convenient to operate.

• Small in size and light in weigh (including the total

weight of the battery is about 50 grams), easy to carry.

• The power consumption is low. Can use Two AAA

batteries.

• Show current battery usage. When the voltage is

very low, the normal operation of the oximeter may

be affected.

• When the ﬁnger is not in the measurement

position for more than 16 seconds, the product will

automatically turn off the power.

Product use range

The Fingertip Pulse Oximeter is used to measure the

blood oxygen saturation and pulse rate of the human

body through ﬁngers. The product is suitable for

families, hospitals (including medical and surgical

departments, anaesthesiology, pediatrics, intensive

care, etc.), oxygen bars, community medical, sports and

health care.

This device is not intended for continuous monitoring.

Operation guide

•

Press the power switch on the front panel to turn on

the power pf Oximeter.

• Pinch the clip of the oximeter, and then put one of

the ﬁngers completely into cavity of the oximeter.

• Press the power switch again to change the display

direction.

• Read the data on the display.

When the ﬁnger is placed in the oximeter, the

nail surface must be upward.

If your ﬁngers are not fully inserted, it may cause

measurement errors.

Disclaimer: Before and after each test, please use

medical alcohol to clean the oximeter rubber parts

that touch your ﬁngers (The rubber in the oximeter

is medical rubbber, which is non-toxic and

harmless to human skin).

Control panel instructions

The height of the bar graph can indicate the

strength of the pulse.

Product accessories

• Lanyard x 1

• User manual x1

Battery installation

• Put the AAA batteries x2 into the battery box

with correct polarity.

• Close the battery cover.

Note: The battery polarity must be installed

correctly. Otherwise, the machine may be damaged.

If the oximeter is not used for a long time, the

battery must be removed.

Lanyard installation

• The thin thread at the end of the lanyard should

pass through the perforation used to assemble

the lanyard.

• Pass the thick thread at the head of the lanyard

through the thin thread at the tail and tighten it.

Maintenance and storage

• When the battery is low, please replace the

battery in time.

• Please clean the oximeter before diagnosing the

patient.

• It is best to place the oximeter in an

environment with a temperature of-10 to 400C

and a humidity of 10%-95%.

• Avoid direct sunlight and exposure to strong

radioactive infrared or ultraviolet rays.

It is recommended to put the product in a dry

environment. A humid environment may affect

its life and even damage the product.

Please dispose of used batteries in accordance

with local government laws.

Dimensions

Length: 58mm

Width: 31mm

Height: 29mm

Weight: 50grams (including AAA batteries x2)

Environmental requirements

Working temperature: 5-400C

Storage temperature: 10-500C

Ambient humidity: 15%-80% work

10%-95% storage

Faults and solutions

• There are no user-serviceable parts in the

oximeter, and only qualiﬁed personnel can

perform repairs.

• If you are not sure whether the measurement is

accurate, you can ﬁrst check the vital signs of

the patient through other methods, and then

ensure that the patient through other methods,

and then ensure that the oximeter is in a normal

working state.

DO not pour, or spill any liquid into the accessories,

connectors, switches, or openings in the oximeter

because it will damage the oximeter.

Questions

Blood oxygen

saturation and

pulse rate

cannot be

displayed

normally

The blood

oxygen

saturation and

pulse rate

display are

unstable

Cannot turn

on the power

The screen

suddenly

turns off the

display

Possible reason

1. Incorrect ﬁnger

insertion.

2. The patient’s

perfusion is too low.

1. The ﬁnger may not

be fully inserted

2. Fingers are shaking

or the patient’s body

is moving

1. The battery is low or

the battery is not

installed

2. The battery is not

installed correctly.

3. The oximeter is

damaged

1. Shut down without

detecting a ﬁnger for

a long time

2. The battery is

exhausted

Solution

1. Retry to insert your

ﬁnger

2. Try several more

measurements, if you

are sure that the

product does not have

any problems, please

go to the hospital for

an accurate diagnosis

in time

1. Try to insert ﬁngers

again

2. Don’t move

1. Please replace the

battery

2. Reinstall the battery

with the correct

polarity

3. Please contact your

local customer service

center

1. Normal

2. Replace the batteries

Sign

%SpO2

/Min

Deﬁnition

Class BF equipment

(refer to IEC 60601-1: 1995)

Attention! Please refer to this manual

Arterial oxygen saturation

Pulse rate

1. Symbol for electrical and electronic

equipment according to 200296/EC

2. The waste after use of the

equipment, accessories and

packaging should be properly

handled, please follow the local

disposal regulations or rules

Note: The oximeter applies to this rule

Sign deﬁnition

Manufactured and Marketed By:

iGear Tech Pvt. Ltd.

204, Sai Corporate Park, Laxmi Nagar, Off Link

Road, Goregaon West, Mumbai - 400104.

In case of consumer complaints:

Toll free number - 1800 22 8495

Email: [email protected]

(Between 10am to 5pm, Mon- Fri)

iGear iG-PO1 User manual

iGear iG-PO1 User manual

Related papers

Other documents