V I V O MOUNT-RAIL02H User manual

MOUNT-RAIL02H
V I V O
Brand
V I V O
Model
MOUNT-RAIL02H
Type
User manual
Height Adjustable Clamp and Rail Set for Custom
Wood Tray - 2 Pack
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-rail02h
SKU: MOUNT-RAIL02H
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
2
ASSEMBLY STEPS
STEP 1
PACKAGE CONTENTS
WARNING!
Phillips
Screwdriver
A (x2)
Slider Bracket
B (x2)
Clamp
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do
not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly
or inappropriate use.
11lbs
(5kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
C (x2)
Support Bracket
D (x2)
Clamp Pad
S-A (x6)
M4x7mm Screw
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
NOT INCLUDED
TOOLS NEEDED NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED.
S-C (x6)
M5x8mm Screw
S-B (x8)
ST5x12mm Screw
Assemble Slider Brackets (A) to the Support Brackets (C) using M4x7mm Screws (S-A), making sure the
countersunk holes on Support Brackets (C) are facing outward, as shown below. Tighten with a Phillips
screwdriver.
S-A
CA
NOTE: Clamp can be oset using the extra holes in Slider Brackets (A) to allow the tray to be pulled out an extra 1.2”
(30mm) when in use. If mounted this way the tray will sit further out from desk edge.
NOTE: Countersunk holes
should be facing outward.
3
STEP 2
Assemble Slider Brackets (A) with Support Brackets (C) to the keyboard tray using ST5x12mm
Screws (S-B), and tighten with a Phillips screwdriver.
NOTE: We recommend using a tray with a depth of no less than 10.5”, and a thickness of at least 5/8”.
STEP 3
STEP 4
Desktop
Assemble Clamps (B) to Support Brackets (C) at desired height using M5x8mm Screws (S-C). Tighten
with a Phillips screwdriver.
NOTE: Slider Brackets (A) and Clamps (B) should be paired with the corresponding "L" and "R" stickers.
Place Clamp Pads (D) on the underside of each Clamp (B). Place assembled keyboard mount on edge
of desktop and tighten Clamps (B).
NOTE: To ensure keyboard tray is level, do not over-tighten Clamps (B). Slide keyboard tray forward/
back to desired position.
A
C
S-B
BC
S-C
A
D
B
Front
LAST UPDATED: 08/09/2022
REV2
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

V I V O MOUNT-RAIL02H User manual

MOUNT-RAIL02H
V I V O
Brand
V I V O
Model
MOUNT-RAIL02H
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents